GE 861 EWS-12 (T)/ 2025-26

Amount

Taking down chowkhat or frame with shutters (without taking shutter from the frame) exceeding 1.5sqm and not exceeding 4.00 sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down Chowkhats or frames n. exc 1.5 Sqm each with shutters (without taking off shutters from the frames), complete all as specified and directed by Engineer-in-Charge.

Taking down of shutter any description area exceeding 1 sqm but not exceeding 2 sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge. NOTE: The work is to be carried out upto 10 mtr height.

Demolition of cement concrete of Roofs, floors , beams, staircases, landing,(other than ground floor ) chajjas and similar suspended work complete all as specified and directed by Engineer-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors & paving n.exc 15 cm thick (below or above ground level) complete all as specified and directed by Engineer-in-Charge.

Dismantling wall and ceiling boards (fibre, Pulp, insulation etc) or insulation board/slabs/blankets, any thickness, including cover fillets & snap grid frame etc, complete all as specified and directed by Engineer-in-Charge.

Dismantling timber scantling framed work 40 sq cm and over in section in any position, complete all as specified and directed by Engineer-in-Charge.

Dismantling plain or corrugated steel sheeting , any gauge and thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed by Engineer-in-Charge.

Taking down and refixing of shutters of any description in same opening exc 1 Sqm and n.exc 2 sqm complete all as specified and directed by Engineer-in-Charge.

M & L for 2nd class softwood, plain, solid, straight chowkhats and frames, wrought, framed, wrought, framed rebated on the solid, rounded of chamfered, put together with glue pinned complete all as specified and directed by Engineer-in-Charge.

M & L for 35 mm thick, 2nd class soft wood factory made, Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkhats complete all as specified and directed by Engineer-in-Charge.

M & L for 35mm thick, 2nd class softwood factory made glazed and skeleton shutters, open rebated and prepared to receive glass or gauge, etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (a) for door shutter supplying and fitted to chowkhats, complete all as specified and directed by Engineer-in-Charge.

S & F glazed and skeleton shutters, 30mm thick of 2nd class soft wood, open rebated and prepared to receive glass, gauge etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted without and mitred beads for securing glass etc., sizes of members of shutters as specified in SSR Part I section B clause 8.24 (a) complete all as specified and directed by Engineer-in-Charge.

S & F Factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing shown in SSR Part-II, complete all as specified and directed by Engineer-in-Charge.

S & F Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and joined together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified and directed by Engineer-in-Charge. moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and joined together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified and directed by Engineer-in-Charge.

S&F 150mm long mild steel barrel tower bolts, stove enamelled black, with bright bolts fixed, complete all as specified and directed by Engineer-in-Charge.

S&F 150mm long, mild steel pressed handles, oval type, stove enamelled black, complete all as specified and directed by Engineer-in-Charge.

S&F 250mm size Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed by Engineer-in-Charge.

S&F 100mm long mild steel barrel tower bolts, stove enamelled black, with bright bolts fixed, complete all as specified and directed by Engineer-in-Charge.

S&F 100mm long, mild steel pressed handles, oval type, stove enamelled black, complete all as specified and directed by Engineer-in-Charge.

S&F 100mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed by Engineer-in-Charge.

S&F in repair stainless steel sink , made out of 1.00 mm thick sheet of overall size 600x750mmx250mm complete all as specified and directed by Engineer-in-Charge. Make: Nirali/Diamond/Blue King/Kingston.

Taking down & Fixing in repairs the same Steel rolling shutters, with out ball bearing, as specified including top cover, greasing, oiling, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 19/20mm dia MS Pipe powder coated Drapery rods of approved colour as in decorative type complete all as specified and directed by Engineer-in-Charge.

S&F in repairs brackets for drapery rod of powder approved decorative type suitable for fixing drapery rods of 19/20mm dia pipe including fixing screws, drilling etc as per sample approved by Engr-in-charge complete all as specified and directed by Engineer-in-Charge.

M & L for Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm & fixed with stainless steel wire staples (fixed in repair), complete all as specified and directed by Engineer-in-Charge.

S&F in repairs vitreous china squatting pan water closet, Orissa pattern, size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) but including PVC (SWR) 'P' trap, jointing to flush pipe complete and making good to floor in cement concrete M-5 (1:5;10), type E-2 using 40mm graded crushed stone aggregate, complete all as specified and directed by Engineer-in-Charge.

M & L for Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm & fixed with stainless steel wire staples, complete all as specified and directed by Engineer-in-Charge.

M & L for 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 finished the surface even and smooth without using extra cement including mixing of water proofing compound in the proportion as mentioned in manufacture's instructions complete all as specified and directed by Engineer-in-Charge. Note: (a) Water proofing compound shall be measured and paid for separately. (b)The work is to be carried out upto 10 mtr height.

M & L for 10mm thick rendering on fair faces of brick or concrete surfaces in CM 1:6 finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.

M & L for Supply only liquid water proofing compound of approved quality, complete all as specified and directed by Engineer-in-Charge.

M & L for Non-skid joint less coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6, complete all as specified and directed by Engineer-in-Charge.

M & L for Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but not exc 0.18 sqm, as in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in cement mortar 1:4 to receive tiles complete all as specified and directed by Engineer-in-Charge.

M & L for 40mm thick PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in floors, finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.(floor to be laid in panels)

M&L for glass dividing Strips, 3mm thick and 38mm width of strip and inserted in position to confirm to design complete all as specified and directed by Engineer-in-Charge.

M & L for Plain cement concrete 1:3:6, type C-2, using 40mm graded mechanically crushed stone aggregate, 50mm thick, as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays, complete all as specified and directed by Engineer-in-Charge. Note:- The unit rate include for use of form work (straight or curved).

M & L for 6mm thick plywood, grade BWR, type BB, fixed in ceiling flat and sloping with nails to timber frame, complete all as specified and directed by Engineer-in-Charge.

M & L for 6mm thick plywood, grade BWR, type BB, fixed in walls with nails to timber frame, complete all as specified and directed by Engineer-in-Charge.

M & L for 2nd class softwood plain fillets square/rectangular or triangular in section of sectional area exc 13 Sqcm but n exc 25 Sqcm including dismantling old unserviceable fillets, complete all as specified and directed by Engineer-in-Charge.

M & L for 2nd class softwood plain fillets bull nosed splayed chamfered or rounded on one edge or face in section of sectional area exc 3 sqcm but n.exc 6 Sqcm complete all as specified and directed by Engineer-in-Charge.

M & L for 2nd class softwood plain fillets square/rectangular or triangular in section of sectional area n exc 3 Sqcm, complete all as specified and directed by Engineer-in-Charge.

M & L for 2nd class soft wood weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps complete all as specified and directed by Engineer-in-Charge.

M & L for 2nd class softwood, as in scantling and similar work, clean sawn, timber fixed in position, complete all as specified and directed by Engineer-in-Charge.

S & F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

S & F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed.

S&F in repair 10 litre capacity PVC valve less, low level, synphonic action type, flushing cistern, with inlet, ball valve, float valve, handle including brackets, complete all as specified and directed by Engineer-in-Charge.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm, complete all as specified and directed by Engineer-in-Charge.

S & F in repair 15mm bore bib tap, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule, complete all as specified and directed by Engineer-in-Charge.

M&L in repairs for weather boarding in 2nd class softwood clean swan , plain , 20 mm thick or feather edeges , 15 mm to 20 mm thick and fixed with 30 mm laps joints complete all as specified and directed by Engineer-in-Charge.

M & L for 4mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed by Engineer-in-Charge.

M & L for 4mm thick sheet glass ordinary quality, and glazing with oil putty or fixed with bead/glazing pins in squares exc 0.50 Sqm in each pane, complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of old surfaces of walls, plastered or unplastered including brooming down or steel wire brushing scraping down smoke soot, moulds moss and efflorescent salts and treating oil and greasy spots and applying one coat of white wash on wall, complete all as specified and directed by Engineer-in-Charge.

All as per item No 55 above but applying one coat of white wash on ceiling, complete all as specified and directed by Engineer-in-Charge.

All as per item No 55 above but applying one coat of cement based paint on wall, complete all as specified and directed by Engineer-in-Charge.

M & L for complete removal of existing treatment from external surfaces of walls by wire brushing and washing down and stopping of surfaces and preparation of surfaces by applying 3mm thick wall care putty as required to obtain smooth and even surface and then applying two coats of oil bound distemper, white or tinted complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of old painted GI/steel surfaces of any description not otherwise described over 10cm width or girth as in roof and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M & L for Preparation of new plastered or unplastered surfaces of wall and applying two coats of cement base paint over a coat of alkali-resistant priming coat, complete all as specified and directed by Engineer-in-Charge. NOTE: The work is to be carried out upto 10 mtr height.

M & L for Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over wall putty, on plastered surfaces preparatory to distempering, complete all as specified and directed by Engineer-in-Charge.

M & L for Preparation of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing air termination single pointed copper rod not less than 12mm dia and 300mm long including fixing of GI base on epoxy insulators of suitable size to isolate from the roof and fixing of insulators on roof over the purlin/RCC roofs, using self tapping screws of suitable length or other means to make the roof leakage proof for fixing of air terminal rod and connecting with down/roof conductors complete all as specified and directed by Engineer-in-Charge.

M&L Plain cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in bed blocks/PCC Blocks/dunnage blocks of size 200mmx200mmx200mm and placing and fixing the blocks wherever required complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Aluminium strip 25x3mm including epoxy/porcelain insulators of suitable size, distance between insulators not more than 1 mtr including fixing screws washers etc complete for PCC block of size 200x200x200mm excluding cost of PCC block for RCC roof, using screws, washers, gutti/rawal plugs etc complete all as specified and directed by Engineer-in-Charge. Note : (PCC Block shall be measured and paid separately)

Material and labour test point terminal block made of gun metal or phosphorus bronze size 75 x 75 x 25 mm drilled and screw end connected to existing Aluminium/GI strips complete including 3 nos. 8 mm dia 25 mm long hex. head screw complete and including fixing of test point with sheet metal enclosure on insulators to isolate from the walls, fixing of insulators on wall using suitable size of screws, washers, gutti/rawal plugs etc, including making good to disturbed surfaces complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair GI pipe light grade including provision of all fittings laid in pavement, road crossing, protection to earthing lead and the like and soil complete of size 40mm dia for protection of GI strip complete all as specified and directed by Engineer-in-Charge.

Earthing complete with copper earth plate electrode of size 600 mm x 600 mm x 3.15 mm thick buried directly to ground vertically to a depth not less than 2.25 Mtr below the ground level with top edge of earth plate not less than 1.65 Mtr below normal ground level connected to 20 x 3mm copper strip and earthing lead protected with 50 mm dia GI pipe light grade filling around with charcoal dust and salt including excavation, returning, filling of earth and disposal of surplus soil to a distance not exceeding 50 mtr and connected to GI strip by means of GI nuts, bolts and washers strip connected to earth plate including chamber PCC 1 : 3 : 6 type C1. using 20 mm graded stone aggregate in concrete pit pre-cast RCC 40 mm thick reinforced with 6 mm dia round at the rate of 75 mm C/C both way with 12 mm dia mild steel plain bar lifting handle 2 Nos funnel with wire mesh 20 mm dia GI pipe light grade watering pipe and frame work complete all as shown in electrical plate No. 3 of SSR Part - I 2009 including testing complete. (20x3mm copper earth strip upto 7.5 m length in included in unit rate quoted by contractor and beyond this length the same shall be measured & paid separately.

M/S Manzoor Constructions (BID ID -3326014)

M/S TANTRAY AND CO (BID ID -3327747)

M/S S. D. BUILDERS (BID ID -3328109)