Construction of Additional alteration of ICU/HDU in existing Civil Hospital at Fatehabad

Amount

Dismantling brick work, tile masonry or tile lining and tile terracing (HSR 8.5 (b) in cement

Dismantling cement conglomerate/ terrazo floors 25 mm to 50 mm thick without concrete base (HSR 8.26)

Dismantling white or coloured glazed tiles (to be carefully removed) (HSR 8.38)

Cement concrete 1:1½:3 with stone aggregate 20 mm nominal size for reinforced concrete work for walls exceeding 20 cm thickness (Straight and curved) beams, girders, stairs, columns, (square or rectangular) battens and lintels etc. excluding steel reinforcement but including centring and shuttering, laid in position complete in all respects. [HSR. 10.86+10.95 (a)]

First class brick work laid in cement sand mortar 1:6 in 1st storey upto 4 metre above plinth level. (HSR 11.7)

11.43 cm thick brick wall laid in cement sand mortar 1:4 in spuer-structure. [HSR 11.48 (a)].

Terracing consisting of tiles 22.86 cm X 11.43 Cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 kg per sqm on top of R.C.C slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc., (HSR 13.13).

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised @80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be prepainted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. (with or without grooves). (HSR 13.92).

Conglomerate floor 50 mm thick cement concrete topping 1:2:4 (HSR. 14.10)

PVC (viny I) asbestos tiles as per IS 3461-1961 coloured and marbled or mottled finish flooring on a smooth and damp proof base using adhesive as recommended by manufacturer including rolling with light wooden roller weighting about 5 Kg complete in all respect as desired by Engineer-In-Charge (HSR 14.75 (b) 3 mm thick

Providing and Fixing vitrified tiles of 600 x 600 mm of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1.3 and jointed with white cement slurry mixed with pigment to match the shade to tiles (HSR 14.89) Note: - Tile shall be to premium quality (first quality) of reputed manufacturer like NITCO, KAJA-RIA, SOMANI, ORIENT, JOHNSONS & RAK

Providing & fixing ceramic tiles/anti skid tiles of size 400mm x 400mm or above size of approved make in flooring, laid in any pattern as specified over base of 20 mm thick cement coarse sandmortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like:- RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL, SIMPOLO shall be used as approved by Engineer-in-charge. (HSR 14.91). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing & Fixing Ist quality Ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete. (b) Size of ceramic Glazed tiles 300 x 450 mm of reputed manufacturer like:- RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL, SIMPOLO shall be used as approved by Engineer-in-charge. [HSR 14.92(b)]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

12mm thick cement plaster on walls (1:6). (HSR 15.7).

Cement pointing 1:2 flush on flat brick flooring (HSR 15.71)

Painting two coats with synthetic enamel paint in all shades on old wood work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint (HSR 16.5) Through Rate

Providing and Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surface. (Note:- First quality paint of reputed make firm such as Goodlass-Nerolac, Berger, Garware, Jenson, Nicholson, Asian & Shalimar Shall be used as approved by Engineer-in-charge in writing, Drum of paint shall be opened in presence of Engineer-in-charge). (HSR 16.25). Through Rate

Preparation of plastered surfaces for distempering including sand papering the surface, applying filling with approved quality filler, consisting of plaster of paris and chalk mitti including finishing the surface to the required finish complete (HSR 16.51) Through Rate

Distempering with washable oil bound distemper (of approved manufacture) two coat on old distempered work (HSR 16.60)

Cost of aluminium fittings complete for doors and windows, such as tower bolts, handles, etc. and screws for these fittings (excluding sliding bolt) (HSR 17.72 (a) for single leaf shutter

Providing and fixing sliding bolt with nuts and screws etc. complete (HSR 17.83 (a) brass (i) size 300 mm x 16 mm

Factory manufactured wire gauze door and window shutters of commercial hard wood such as Hollock, Champ, Chikrassy & Chaplash only. (non-coniferous timber other teak conforming to I.S. specification No. 1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position. (Styles and rails of windows shutter shall be 75 mm wide. (i) 30 mm thick. [HSR 17.92 (i) - Note 1 under 17.18]

Factory manufactured Solid Flush Door Shutter, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hotpressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position. (Note:- reputed make such as Duro, Green, Kitply will be used as approved by Engineer-in-charge). HSR 17.93 (a) - Note 1 under 17.18]. (iii) 35 mm thick Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Providing and fixing Aluminum work for doors, windows, ventilators and partitions, Structural Glazing with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS;733 and IS;1285 fixed with raw plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom, and sides with required neoprene felt etc. aluminum sections shall be smooth, rust free straight mitered and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing/paneling C.P brass/stainless steel screws. All complete. Fixed portion (Anodized Aluminum transparent or dyed to required shade according shade according to IS;1868, minimum anodic coating of grade AC 15). [HSR 17.95 + Note (ii)]. Hindalco, Jindal make.

Providing and fixing 12 mm thick preleminated paticle board flat pressed three layer or graded wood particle board conforming to IS;12823 grade I type II in paneling fixed in aluminium doors. Windows shutters and partition frames with c.p brass / stainlees steel screws etc. complete (b) Pre-laminated particle board with decorative lamination on both sides. [HSR 17.97 (b)].

Providing and fixing glazing aluminium door, windows ventilator shutter and partitions etc. with PVC/neoprene gasket etc. complete (cost of aluminium snap beading shall be paid in basis items.) (b) with float glass panes of 5.00 mm thickness. [HSR 17.98 (b)].

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS 6315 marked for door including cost of cutting floors as required embedding in floors and cover plates with brass pivot and single piece M.S sheet outer box. (a) with stainless steel cover plate. [HSR 17.99 (a)].

Supplying and fixing Glass panes including special metal sash putty of approved make. (b) glass panes 4 mm thic, exceeding 40 sq. dm areas. [HSR 18.30 (b)].

Pressed steel sheet frames (chowkhats) consisting of 2mm thick steel sheet of the specified section, including iron lugs (hold fasts) iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete. (HSR 18.34 (b) door and window frame of size 76 mm x 38 mm with 35 mm wide single regbate

NS ITEMS Providing and Laying Pre-polished Granite stone 17 mm & above Like :- Z-Black in skirting/dados, risers of steps, pillars, wall facing, laid in any pattern as specified over base of 12mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mixed with pigment to match the shade of granite including labour for fixing cramps pins and dowels etc. (NS).

(PUBLIC HEALTH WORK) Providing & Fixing in position best Indian make (to the approval of the Engineer-in-charge). Indian orissa or orya water water closet suite for sinking into floor, with raised foot treats complete with 100 mm H.C.I.'P' trap with or without vent as required and all other necessary fitting as fully described. (HSR 30.2 (a) Size 580 mm (ii) white

Providing and fixing in position best indian make (as approved by the engineer-in-charge European type water closet suite, syphonic type consisting of- (i) VITREOUS CHINAWARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in-charge). (ii) One piece SEAT AND LID IN HOLLOW BLACK OR WHITE PLASTIC fitted with chromium plated hinges and rubber buffers, (to the approval of the Engineer-in-charge) COMPLETE in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS (HSR 30.5 (a) Single trap syphonic WC suite (i) White

EXTRA OVER item nos. 30.1 to 30.4 and 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY C.I. LOW LEVEL VITREOUS CHINAWARE CISTERN complete with flush bend all other necessary Fittings instead of C.I high level cistern complete with fittings. (i) White. [HSR 30.12 (i)].

Providing and fixing in position best Indian make a range of three urinals flat back or angular lipped in vitreous chinaware with one No. 10 letres capacity best Indian make CI automatic flushing cistern with fittings and flush pipe etc. complete fully described Item No. 30.19 above (HSR 30.21 (i) White (Make Hindware)

Extra for providing and fixing vitreous automatic flushing cistern including fittings and brackets instead of CI flushing cistern complete (HSR 30.37 (a) 5 Litres capacity Cistern (i) white

Extra for providing and fixing standard size CP brass flush pipe complete with fittings instead of GI flush pipe complete (HSR 30.38 (iii) For a range of three urinals

Providing and fixing 25 mm thick marble partitions for different type of urinals. (HSR 30.40 (a) Size 375 mm x 750 mm

Providing & Fixing in position best indian make (ordinary) lavatory suites consisting of:- (v) Size 560 mm x 450 mm with one no. tap. [HSR 30.41(v)].

Providing & fixing in position best Indian make bevelled edge 5.5 mm thick mirror mounted on absetos sheet ground fixed in postion by means of 4 Nos. chromium plated brass screws and washers over rubbers washers and rawl plug embeded in the wall or chromium plated brass clamps with C.P. brass screws (as required by the engineer-in-charge) complete including cutting and making good the walls etc. (a) Indian Make (i) 600 mm x 450 mm. [HSR 30.71 (a) (i)].

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (as required by the Engineer-in-charge). (a) Bib cock long body. [HSR 30.75].

Providing & fixing in position C.P. brass stop cock (as approved by the engineer-in-charge). (a) 15 mm Stop cock. (ii) Concealed stop cock with flange. [HSR 30.76 (a) (ii)].

Providing and fixing in position M.S. or heavy flat iron clamps made out of M.S. flat not less than 5 mm of the approved design for fixing C.I. soil waste vent or anti pipes to walls complete in all respects. (a) for 100 mm interal diameter pipes. (HSR 30.88) (b) for 75 mm interal diameter pipes.

Providing and Fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers flages for connections in tanks complete in all respects to the satisfaction to the Engineer-in-Charge. [HSR 30.119] 1000 Ltrs. Capacity Water Tank

DSR ITEMS Providing and fixing GI pipes complete with GI fittings and clamps i/c cutting and making good the walls etc. (DSR 18.10) (ii) 20 mm dia nominal bor

(iii) 25 mm dia nominal bor

Providing and fixing gun metal gate valve with C.I. Wheel of approved quality (Screwed end). (DSR 18.17) (b) 20 mm nominal bore

(c) 25 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New Work). (DSR 18.46) (b) 20 mm nominal bore

(c) 25 mm nominal bore

M/S KIRORI CONTRACTOR