WBPHE/DIC/BMSD(D)/NIeT-13 of 2023-24/1

Amount

Supply & delivery at site of sheet cubical type dust & vermin proof indoor type single front wall mounted manual motor control centre for operation of the pump motor in star Delta mode (7.5 H.P-12.5 H.P), DOL starter for chlorinator,timer operated outdoor and indoor lighting , made of 2 mm CRCA sheet having common bus bar & individual cable alley of the panel including epoxy based powder coated paint on both inside & outside as per approved drawing : Make of panel: PCE project Pvt. Ltd./ ECS/ system control & automation/ RNR industries/ prayaas automation Pvt. Ltd/ Electromech Engineers]

Installation and commissioning of above panel on wall with grouting arrangement including supply of necessary sand, cement etc as required to complete the job with all electrical connection as per direction & up to the entire satisfaction of the EIC.

Supply and delivery of following materials at site

1.1 KV grade 415 V, 25 sqmm, 3.5 core PVC insulated Aluminium Armoured Cable.(Make-Havells/Gloster/other approved make)

Laying of 25 sq. mm. 3.5 core AL. Ar. Cable in wall/ floor by supplying of all necessary materials as per IE Rules and as per direction

Making joints of the cable by supplying compresion type gland thimple, socket etc. as per requirement and as per direction of EIC.

Supply and laying of 50 mm. dia. non metalic pipes (IS:14930) and specials for protection of submersible cable.

Supply and fitting of Pressure gauge [H.Guru/Febig] 150 mm dia [0-7Kg/Sq.cm] brass cock and fitting complete[This cost includes 15 mm. dia G.I. pipes and specials].(Make-Febig/H.Guru)

80mm dia. CIDF Non-Raising Sluice Valves, PN 1.0 rating (Conforming to IS:14846) for delivery pipe line and wash out line. *MOC & TC needed for valve.

Supply & delivery at site

80mm dia. CIDF Tee.

80mm dia. CIDF Bend.

80 mm dia CI/MS flanged short piece 0.50 mtr.

Making washout line with supplying all fitting fixing materials to complete the work.

Making brick pillar 0.25 x 0.25 x 0.75 Mtr/Suitable hight for supporting of valves and pipes with 12mm thick plaster and net cement finish complete.

Supply & delivery of plastic Chair without arm(Model: Dream/similar)(For P/H-I&II)

Supply & delivery of plastic Table (Model: Arjun/similar)(For P/H-I&II)

Supply & fixing MS fan clamp of two pices type for RC celling or steel joist as per approved specification fabricated from 40mm x 9mm MS flate incl making good damages to building roof with satisfactory finishing and painting. (For PH-II)

Supply and fixing 240v electronic step type socket type fan regulator to be fixied on eixiting switch board (Anchor make) including cutting top cover as per direction of EIC. (For PH-II)

S&F of 240V 48"(1200mm) sweep ceiling fan (make Crompton Greaves /Havells/usha) (For PH-II)

Making earthing arrangement as per following --

Excavation of soil for installation of Earth electrode and filling and ramming for soft soil.

Earthing with 50 mm dia Gl pipe 3.64 mm thick x 3.04 Mts.long with TATA-Medium GI pipe with a provision to connect 25mm X 6mm GI flat strip complete with GI bolts, nuts, washers etc as required.

Supplying & fixing of earth Busbar of galvanized (Hot dip) MS flat 25mm X 6mm on wall having clearance of 6mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulator etc as required.

Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required

Extra for providing masonery enclosure on the top of the earth electrode of overall size 86.36cm X 86.36cm X 46cm deep (below ground level) complete with cemented brick work (1:6) of 25cm width duly plaster with cement morter (inside) CI hinged inspection cover of size 36.56cm X 35.56cm with locking arrangement, GI reducer including drilling of 46nos. 12mm dia holes on the GI pipe.

Extra treatment of soil by using salt and charcoal or coke for plate electrode.

Painting of the installation (viz valves, pipe lines(delivery,wash out and tubewell) etc. by two coats of epoxy paint (colour to be decided by EIC) over a coat of primer as per and direction of EIC.

Add GST @ 18%

Add Cess @ 1%

Moni Electrical Works

C M ENTERPRISE