CONSTRUCTION OF BULK STORE FOR TECHNICAL STORE SECTION AT BLDG NO P-238, ADDN / ALTN TO RAMP, GARAGE FLOORING ETC AND CERTAIN MINOR WORKS AT STATIC WKSP EME AT SRINAGAR COLONY UNDER GE MINNIEBAY, SRI VIJAYA PURAM

Surface excavation over Hard/ dense soil n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft soil complete all as specified and directed.

Surface dressing not exceeding 15 cm deep and geting out in soft/loose soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 sqm on plan and n.exc 1.5 m in depth and getting out in soft /loose Soil complete all as specified and directed.

Excavating in post holes or similar holes, each not exceeding 0.5 Cum, getting out in Hard/ dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 M and making good surface complete all as specified and directed.

M&L Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M&L for form work to sides of rough finished concrete foundations, foootings, bases of columns, raft and raft beams, sides and soffits if any of foundation and plinth beams and similar work vertical or to batter compelte all as specified and as directed.

M&L for form work to posts, struts, piers, columns and stanchions complete all as specified and as directed.

M& L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. flat , fair finished surfaces complete all as specified and as directed.

M&L for RCC M30 (nominal mix) (using 20 mm graded stone aggretate) in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L for RCC M30 (nominal mix) (using 20 mm graded stone aggretate) in Columns, pillars, piers, posts and struts complete all as specified and directed.

M & L for RCC M-30 nominal mix concrete (using 20 mm graded stone aggretate) as in Beams, antilevers, bressummers, lintels over 1.5m span and the like complete all as specified and directed.

M&L for TMT bars 10mm dia and over as in reinforcement cut to length, bent to shape required including cranking hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing clips complete all as specified and directed.

M&L for TMT bars 6 mm to 8 mm dia in stirrups, spacers, and binders in reinforcement cut to length, bent to shape required including cranking hooking ends and binding with mild steel wire complete all as specified and directed.

M & L for hardcore of gauge not exceeding 63 mm of broken granite stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Material & Labour for Moorum/Red Bajri Filling in floors or pavings, laid in layers n exc 15cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for PCC 1:5:10 type E2 (40mm graded aggregate) as for floor surface complete all as specified and directed.

M&L for pre-construction ATT for treating the the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface complete all as specified and directed.

M&L for pre-construction ATT for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for pre-construction ATT for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

Returning filling including spreading, levelling, watering and well ramming in layers n.exc 25cm complete all as specified and directed.

Removing Excavated soils not exceeding 50M and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as specified and directed.

Demolition of Precast Concrete work built in Cement Mortar including all quoins arches pillars etc complete all as specified and as directed.

M&L precast cement concrete block masonry with PCC solid blocks in 1:3:6 type C1 using 20mm graded stone aggregates, exc. 10cm in width and set in CM 1:4 complete all as specified and directed.

M&L for rendering 10mm thick on fair faces of brick/concrete surface in CM (1:6) finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 with water proofing compound (water proofing compound shall be used as per manufacturers instructions over brick or concrete surfaces finished even and fair complete all as specified and directed.

Supply only water proofing compound conforming to IS-2645 1975 complete all as specified.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete set and jointed in neat cement slurry and pointed in white or coloured cement to matchover and including 15mm thick cement screed in CM 1:6 all complete all as specified and directed.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with laid over cement screed and jointed withincl 10mm thick CM 1:4 as in baking coat of dado/skirting complete all as specified and directed.

Supply and fixing factory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws complete all as specified and directed.

Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply only 4mm thick figured glass, pin headed type glass ordinary quality fixed in aluminium ventilator complete all as specified and directed.

Supply only 4mm thick sheet glass, ordinary quality fixed in aluminium window along F section complete all as specified and directed.

M&L for 12 mm thick Pre laminated interior grade both sides decorative fixed with all necessary fixtures to aluminium door / window / partation & etc complete all as specified and directed.

Supply and fixing Solar control film 25 micron reflective type (gareware sun control or equivalent ) complete all as specified and directed.

Supply only aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40 mm complete in repairs complete all as specified and directed.

S&F floor door stoper of length 140mm of Aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F aluminium anodised snap grid false ceiling of standard aluminium section such as wall angle of size 38mm x 25mm x 2.4mm weighing 0.36 Kg/Rm main/cross tees of size 36.5mm x 25mm x 1.4mm weighing 0.24 Kg/Rm, grid size n.exc. 610 x 610mm suspended with 4mm dia GI wire at interval n.exc. 600mm centre to centre for main & cross tees fixed to roof slab, roof truss fixed with suitable size MS hook and fastening bolts etc complete all as specified and directed.

M&L 4 mm thick non asbestos fibre cement building boards fixed or laid/inserted to timber/GI/Aluminium framework with screws in ceiling confirming to IS-14862 and fixed with necessary clips complete all as specified and directed.

S& F steel work in tubular trusses including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and directed.

S& F for MS Rolled sections in cross beem , hip and jack rafters , vertical posts purlins where connected to common rafters fixed with angle cleats or connecting plates any similar work including welding, and all necessery works complete all as specified (grade of steel Fe-410- (Gde- E-250) quality- B )

M&L for preparation of new or previously untreated steel surfaces over 10cm in width or girth and applying two coats of syanthetic enamel paint over one coat of red oxide complete all as specified and directed.

M&L for preparation of new steel surfaces of any description n.exc. over 10cm width or girth when unconnected with other painting or when painting in diff tint and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as manufacturers instruction complete all as specified and directed.

M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for oil bound distempering two coats over a coat of alkali resistant priming paint including preparation of new plastered or unplastered surfaces of wall complete all as specified and directed .

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M&L for 75mm thick Cement concrete in C1 type (1:3:6) using 20mm graded stone aggregate as in plinth protection and finished even and smooth with using extra cement complete all as specified and directed.

Material and Lobour for 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

M&L for PVC (SWR) bends any radius 110mm bore complete all as specified and directed.

M&L PCC 1:4:8 D2 (40mm graded aggregate) 100mm thick for paving,sub base path etc complete all as specified and directed.

S&F heavy duty vitrified tiles, Durastone, weather proof impact resistant, abrasion resistant tiles of size 300x300x10 mm or high dimension except thickness of any colour any design as approved.including screed bed 15mm thick 1:6, complete all as specified and as directed.

S & F Aluminium flat iron work in wind ties 25x6mm size fixed with 50mm/ 75 mm aluminium self staging screws with integral EPDM washer screwed in roof covering complete all as specified and directed.

M&L For Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for sand cushion over sub base ,complete all as specified and directed.

M&L 100 mm Cement concrete type D- 2, 1:4:8 (40mm graded aggregate) for pavement of pathway complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape with grey cement with pigment and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed.

M&L for PCC Type B-0, 1:2:4 (12.5 mm Stone Aggregate) , copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, kerb stop rounded or chamfered in edges complete all as specified and directed.

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 (nominal mix) grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M & L for angle iron posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E complete all as specified and directed.

M&L PVC coated GI chain link fencing 3.5mm dia with 50mm x 50mm mesh including fixing of MS line wire / rod, flat iron & machine made hexagonal or square head bolts to fencing posts complete all as specified and directed.

S&F for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other to be fitted with washers with neck dia 11 to 15 mm and length exc 15 cm but n exc 22.5 cm long and one hexagonal or square nuts complete all as specified and directed.

M&L for Mild steel screw bolts (machine made), 8mm dia of neck, with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5 cm but n exc 10 cm long, complete all as specified and directed.

S&F for Mild Steel dia neck in 20mm rag or lewis bolts, screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised, exc 30cm long, complete all as specified and directed.

S&F of Structural steel for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, Fe-410-W(Gde-E-250) quality-B complete all as specified and directed.

M&L for MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment, Fe-410-W (Gde-E-250) quality-B, complete all as specified and directed.

Supply and laying of CPVC pipes 20 mm dia outer bore SDR 11 fittings on walls /ceilings or laying in floors complete all as specified and directed. (Note: Brass fittings measured in Running length)

S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 1000 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection, with water tank on top of roof/slab of bldgs, complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and directed.

M&L for ceramic colour tiles in vertical surface of size 450 X 300 x 7 mm thick, jointless type, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with and including 10 mm thick rendering in CM (1:4) for receiving the tiles, complete all as specified and directed. Make - Kajaria Jhonson / Somany

S&F in replacement of bib cock, 15 mm dia with wall flange made of cast copper alloy, chromium plated, complete all as specified and directed.

One light point controlled by one one way switch

One ceiling fan/ exhaust fan point controlled by one switch

One 3 pin socket outlet 5/6 Amps independent.

One 3 pin socket outlet 5/6 Amps on the same board with other switches

All as per item No 71 here-in-before but cable with 4.0 sqmm size for socket outlet 15/16 amps, independent.

M & L for submain wiring with two single core PVC insulated unsheathed multistranded copper conductor cable of size 6 sqmm (FRLSH) and one single core PVC insulated unsheathed multistranded copper conductor cable green colour of size 6 Sqmm (FRLSH) as earth lead in and including concealed with PVC conduit medium grade of suitable size or surface wiring with PVC casing caping of suitable size and making good the disturbed wall surfaces to match with existing specification complete all as specified and as directed. Note : (i) Three run of cable with one run of PVC conduit/PVC casing and caping will be measured as one length. (ii) Wiring shall be concealed/ on surface with rigid PVC conduit medium grade/PVC casing caping as per site requirement. (iii) Cutting chasis in wall/floor beam to be concealed conduit and making good the disturbed surface will be measured & paid seperately. (iv) Electric Wiring test sheet before and after completion of wiring to be submitted before claiming payment.

All as per item No 73 here-in-before but with 1.5 sqmm cable complete all as specified and as directed.

Supply & fixing modular switch one way, 6 Amps, 1 module, 240 volts complete all as specified and as directed.

Supply & fixing modular switch one way, 16 Amps, 1 module, 240 volts complete all as specified and as directed.

Supply & fixing modular socket, 2/3 pin, 6 amps, 2 module complete all as specified and as directed.

Supply & fixing modular socket, 2/3 pin, 6/16 amps, 2 module complete all as specified and as directed.

Supply & fixing ceiling Rose, 3 terminal polycarbonate isolated body complete all as specified and as directed.

S&F LED lights fitting 1 x 20W, 2000lm, CDL, surge protection of 2 KV, 4 feet 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F LED 18W inverter batten type fitting 3/4 feet long aluminium extruded housing, charging time 10-12 Hrs with 04 Hrs backup, IP-20, rated voltage 230 V, 50 Hz, system wattage 20W +/- 10%, system current less than 102 mA, power factor more than 0.95, system lumen efficiency 100lm/watt, CCT 6500K, CRI more than 80, THD less than 30%, driver efficiency more than 85% complete all accessories prewired and connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F LED street fittings comprising of epoxy poeder coated housing, enclosed with glass cover in frame with lumen output not less than 2500 lumens suitable wattage for efficiency not less than 100 lumens/watt having secondary optics, min wattage 25 watt with ingress protection IP 65/66 and potted electronic driver of minimum IP 67 with THD less than 10%, CRI > 80, PF > 0.95, CCT 5700K, IK > 08 SPD of capacity 10 KV and testing on completion complete all as specified and as directed.

M&L for GI bracket for street light fitting made out of 25 mm bore pipe ISI marked light grade GI tube bent to shape required not less than 1.20m long fixed with and including MS flat iron clamps made out of 25x3 mm GI flat, bolts, nuts and washer etc., complete all as specified and as directed.

Supply & fixing exhaust fan metal body, AC, single phase, 230V, 300mm sweep complete with shutter and louvers and exhaust fan shall be fixed with suitable size of buzzer bolt/hold fastner including making hole to the wall surface of any type/girth and at any height for fixing of exhaust fan including making good disturbed surface with existing wall colour and provision of cable from ceiling rose/connector to fan complete all as specified and as directed.

Supply & fixing ceiling fan 1200mm sweep with blades, suitable BLDC remote electronic regulator as per OEM design, down rods and connected accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM, 5 star rated, equipped with brushless direct current motor (BLDC) of wattage < 28W including provision of cable from ceiling rose/connector to fan complete all as specified and as directed.

Supply and fixing MCB SPN 40 to 63 Amps ,10 KA, C Curve, 230 Volts, 50 HZ complete all as specified and as directed.

Supply and fixing MCB SP 6-32 Amps ,10 KA, C Curve, 230 Volts ,50 HZ complete all as specified and as directed.

Supply and fixing PVC insulated, sheathed two core aluminium conductor 10 sqmm cable complete all as specified and as directed.

M&L for earthing complete with Galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below GL) with top edge of earth plate not less than 1.5 Mtr below normal ground level, earth plate surrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using Galvanised earth strip 25x4mm connected by means of bolts, nuts, check nuts and washer of galvanised iron or steel, provision of 15mm dia GI pipe medium grade for protection of GI earth wire and 20mm dia GI pipe medium grade for watering arrangement and PCC (1:3:6) , type C1 chamber, MS funnel, wire gauge, 50 mm thick RCC 1:2:4, type B1 earth pit cover with 6 Nos, 8 mm dia high strength deformed steel TMT bars on both ways including necessary excavation in any type of soil, returning, filling in, removal of surplus soil to distance n exc 50 mtr, provision of charcoal and salt complete all as shown in electrical plate No 3 of schedule Part-I. Note: (i) Cost of GI earth strip and GI protection pipe upto 7.5mtr length shall be deemed to be included in the rate quoted for this item. (ii) The unit rate shall also includes for Wire mesh, funnel, excavation, PCC chamber pit, test point complete.

M&L for cutting chases in concrete block walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 for concealed PVC conduit etc., and making good, cutting not exceeding 10 cm girth etc., including making good disturbed surfaces with existing wall colour complete all as specified and as directed.

S&F GI bracket, light grade 32mm dia and 50cm long including two numbers GI clamp fixed on wall with necessary fixing arrangement complete all as specified and as directed.

M&L concealed submain wiring with PVC insulated unsheathed multi-stranded copper conductor cable two run of 1.5 Sqmm single core (FRLSH) 1100 volts grade drawn through in and including non metallic rigid PVC conduit, medium duty not less than 25mm dia concealed in wall / fixed on wall / ceiling with gI saddles, GI screws, rawl plugs with all fittings and one run of 1.5 Sqmm PVC insulated copper conductor (FRLSH) for earth continuity wire for fixing of security lights complete all as specified and as directed. Note :- (i) Two run of single core cable with one run of earth continuity conductor and PVC conduit and its fittings will be measured as one length. (ii) Rates are deemed to be included for chases of conduit, cutting and making holes in wall / floor for passing in or through conduit and making good disturbed surfaces with existing wall colour complete.

S&F of LED security light fittings comprising of epoxy powder coated housing, enclosed with glass cover in frame (with total lumen output not less than 3000 lumens and suitable wattage for system efficiency not less than 120 lumens / Watt, having secondary optics, min wattage 25 Watt with ingress protection IP 65/66 and potted electronic driver of minium IP 67 with THD less than 10%, CRI>80, P.F>>0.9, IK>08, SPD of capacity 5 KV etc incl necessary clamps etc complete and testing on completion, complete all as specified and as directed. Note : The GI pipe bracket if required will be measured and paid separately under relevant schedule items.

S&F MCB SPN 6 to 32 Amps, 10 KA 'C' curve, 230 Votls, 50 Hz complete all as specified and as directed.

S&F MCB SP 6-32 Amps, 10 KA, 'C' curve, 230 olts, 50 Hz and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

Supply and fix water cooler with in built water purifier capacity with comfort level water outlet temperature 17ºC rated condition 40 LPH, running current in 4.5A, 700W, RO system and water cooler operating volt 180 - 250 Volts, Single Phase, 50 Hz, thermal insulation for storage tank, body storage tank material SS 304 and 5 stages of purification, having approx storage capacity of 80 Ltrs and normal cooling capacity of 40 Ltrs / Hr including suitable pre-filter of complete all as specified and as directed.

S&F of rotational moulded polyetheylene (HDPE water tanks of 250 Ltr capacity cylindrical & vertical type, double layered, ISI marked, hoisted and fixed in position with PVC cover including provision of 40 mm /25/20 mm dia spouts for connecting inlet, outlet, over flow and washout pipes complete all as specified and as directed

Supply and fix of RCBO double pole 30mA, 16A for earth leakage, over load and short circuit protection complete all as specified and as directed.

Supply & Fix single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete all as specified and as directed.

Please Enable Macros to View BoQ information