CERTAIN REPAIR TO ROOFING JOINERY PLASTERING FLOORING ETC AND OTHER MISC WORK AND CERTAIN MAINT OF EM WORK AT 45 WEU UNDER GE AF SRINAGAR

Amount

Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. and removing debries from site all as specified and directed.

Demolition of RCC selves / cooking plateform (reinforement cut as required to facilitate demolition) and similar suspended work and removing debries form site all as specified and directed.

M&L for Brick work with sub class 'B" (using old size bricks) straight or curved of on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified.

M&L for brick work with sub class 'B' Bricks (using old size bricks) straight or curved on plan exc 6m mean radius, built in CM 1:4, complete all as specified and as directed.

M&L for RCC 1:2:4 using, type B0, using 12.5 mm graded stone aggregate as in selves / cooking plateform and similar work complete all as specified & directed.

M&L for form work to soffits & side of selves / cooking plateform flat, fair finished surfaces of concrete not exceeding 100 mm thick complete all as specified & directed.

M&L for mild steel TMT bars 10 mm dia and over cut to length bent to shape including cranking bending spirallay for hooping for columns hooking end and binding with and including mild steel wire (annelead) not less than 0.9mm dia or scuring with clips.

Taking down cement plaster, any description on brick, concrete or stone walls or ceiling including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off all as specified and directed.

M&L for Rendering 15 mm thick in cement and sand mortar 1:6 on brick work or cement concrete wall surfaces including finishing the surface even and smooth without using extra cement complete all as specified.

M&L for Rendering 15 mm thick in cement and sand mortar 1:4 on brick work or cement concrete wall surfaces including finishing the surface even and smooth without using extra cement complete all as specified.

Demolition of floor, hearth or wall tiling or stone slab laid, bedded & pointed in any mortar including demolition of cement mortar bedding or backing coat, including rubbish off the premises, all as specified.

M&L 15 mm thick screed or bedding layer in cement mortar (1:4) for laying floor finishes, complete all as specified.

M&L for 10 mm thick rendering / backing coat in cement mortar (1:3) to receive wall tiles, complete all as specified.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match, all as specified.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match, all as specified.

M&L for non skid ceramic coloured tiles of size 600 mm x 600 mm x 7 to 8 mm thick as in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match, all as specified.

M&L for coloured glazed ceramic tiles in vertical surfaces of size 450 x 300 x 7-8 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as specified.

M&L for colour vitrified ceramic tiles 10 mm thick (square) polished, area of each tiles n.exc 0.36 sqm in floors etc laid over existing screed bed, set and jointed in neat cement slurry and pointed in white or coloured cement to match.

M&L for colour vitrified ceramic tiles 10 mm thick (square) polished, area of each tiles n.exc 0.36 sqm for skirting / dado etc laid over existing backing coat, set and jointed in neat cement slurry and pointed in white or coloured cement to match.

M&L for 18 to 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, wash basin platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including half round molding of exposed edge complete all as specified.

M&L for 18 to 20 mm thick Granite (of any type) work (table rubbed and polished) in vertical surface and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including half round molding of exposed edge complete all as specified.

Taking down shutters of any description, area exceeding 1 sqm and not exceeding 2.00 sqm each complete all as specified and as directed by Engineer-in-Charge

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.50 Sqm each complete all as specified and as directed by the Engineer-in-Charge

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 Sqm but n exc 4.00 Sqm each complete all as specified and as directed by the Engineer-in-Charge.

S&F 35 mm thick, IInd class hard wood plain, framed, paneled factory made shutters (two panel) with lock rail and panel of 12 mm veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified & as directed by Engineer-in-Charge.

S&F 35 mm thick, 2 nd class hard wood, glazed & skeleton factory made shutters, open rebated and prepared to receive glass, gauze etc. (without sash-bars), edges of framing plain, chamfered or rounded fitted with cut and metered beads for securing glass etc., sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.24(a) complete all as specified and as directed by Engineer-in-Charge.

S&F Galvanized mild steel wire-cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified.

S&F Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as shown in drawing of relevant item in MES, schedule Part-II , 2020 as specified and as directed by Engineer-in-Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as shown in drawing of relevant item in MES, schedule Part-II , 2020 as specified and as directed by Engineer-in-Charge.

Supply fabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron) door shutter with frame, partly glazed with 5 mm thick tinted glass and partly paneled with 5 mm thick aluminium composite panels of approved design, including rubber bead joining cleat for fixing in position, aluminium door handle 150 mm size, aluminium barrel tower bolt 200 mm size etc all as specified below complete all as specified and directed. (a) Frame (top & side) section shall of size 101.60 x 44.75 x 2.4 mm ( Section No 14021) (b) Vertical Members of shutter Section shall be of size 85.00 x 44.45 x 2.00 mm (Section No 19560) (c) Top Members of shutter Section shall be of size 83.50 x 44.45 x 2.00 mm (Section No 19581) (d) Lock rail (Middle member) of shutter Section shall be of size 150.00 x 44.45 x 3.00 mm (Section No 19596).....

(e) Shutter Interlock Section shall be of size 18.00 x 40.00 x 1.45mm (Section No 20737) (f) Bottom Members of shutter Section shall be of size 18.00 x 40.00 x 1.55mm (Section No 20736) Note:- Section No given above are of make Jindal, Contractor may use similar section of other make mention in Appx A

S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in position.

S&F Mortise lock vertical type of mild steel 4 levers of size 100mm all as specified.

Supply fabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron) three track window ( two shutters glazed & one shutters wire gauge) with frame, glazed with 4 mm thick tinted glass and, wire gauge with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber bead joining cleat for fixing in position, concealed type lock for all three shutter, PVC roller etc all as specified below, including taking down old window complete all as specified and directed. (a) Frame (top & side) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 20831) (b) Frame (bottom) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 20832) (c) Top & side Members of shutter Section shall be of size 18.00 x 40.00 x 1.55 (Section No 20738)..

(d) Shutter Interlock Section shall be of size 18.00 x 40.00 x 1.45mm (Section No 20737) (e) Bottom Members of shutter Section shall be of size 18.00 x 40.00 x 1.55mm (Section No 20736) Note:- Section No given above are of make Jindal, Contractor may use similar section of other make mention in Appx A

S&F aluminium powder coated minimum thickness of power coated 50 micron of approved colour ventilator, partially glazed and partially louvers, outer frame & mullion fabricated with aluminium section of size 82.50 mm x 38.00 mm x 1.50 mm thick (Cat No 20036), half portion glazed with 4 mm thick frosted glass including rubber beading, & glazing clip, half portion louvers of 80 mm wide & 4 mm thick frosted glass including aluminium louver patti including S.S wire gauge of fixing of 0.36mm dia and 1.40 width of aperture with 25x3mm think aluminium strip with screw to upper half portion of ventilator all fitting & fixture and fixed in position including taking down old steel ventilator complete. Note:- (i) Section No given above are of make Jindal, Contractor may use similar section of other make mention in Appx A

S&F 12 mm thick toughen glass shutters (operable type), with diamond polished clear glass and machine polished edges including all hardware fittings detailed as under, fixed in position as per manufacturer instruction complete.

(a) Stainless steel top patch (Cat No EPF-701) 01 Set.

(b) Stainless steel top pivot (Cat No EPF-712) 01 Set.

(c) Stainless steel bottom patch (Cat No EPF-702) 01 Set.

(d) Glass to wall Stainless Steel lock (cat No EPF-799) 01 No

(e) Stainless steel floor door spring (Cat No FH-ECO-842) 01 Set.

(f) Stainless Steel Handle 300 mm size (Cat No ESBH -011) - 2 Nos For Each shutter

Note:- Cat No mention above for Hardware fitting are of make ENOX, contractor may use similar type hardware fitting of make Approved by GE

M&L for etching on toughened /plain glass designed and pattern as approved by Engr-in-Charge

Taking up or down steel tubing and connections, 15 mm bore fixed on walls, floors or ceiling etc complete all as specified and as directed by Engineer-in-Charge.

Taking up or down steel tubing and connections, 20 mm bore fixed on walls, floors or ceiling etc complete all as specified and as directed by Engineer-in-Charge.

S&F 15 mm bore tubes, 'medium grade', galvanised, with all fitting; ( such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc) and fixed to wall / ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified.

S&F 15 mm bore tubes, 'medium grade', galvanised, with all fitting; ( such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc) and fixed to wall / ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified.

Refixing old steel tubing and connections in new or old position on walls, ceiling or floors etc of size 15 mm bore after cleaning including provn of new fittings all as directed by Engineer-in-Charge (using old steel tubing retrieved from item No 37 above).

Refixing old steel tubing and connections in new or old position on walls, ceiling or floors etc of size 20 mm bore after cleaning including provn of new fittings all as directed by Engineer-in-Charge (using old steel tubing retrieved from item No 38 above).

M&L for Lagging to pipes 15 mm bore used in external water supply or plumbing all around with 50 mm thick bonded mineral wool pre-formed ‘SNAP ON’ pipe sections of density 144 Kg /Cum conforming to IS 9842 provided with chicken mesh wire netting 25 gauge 20 mm mesh complete including taking down of old lagging all as specified and directed by Engineer-in-Charge

M&L for Lagging to pipes 20 mm bore used in external water supply or plumbing all around with 50 mm thick bonded mineral wool pre-formed ‘SNAP ON’ pipe sections of density 144 Kg /Cum conforming to IS 9842 provided with chicken mesh wire netting 25 gauge 20 mm mesh complete including taking down of old lagging all as specified and directed by Engineer-in-Charge

S&F Aluminium handles cast type anodised of size 125 mm long ISI marked complete all as specified and as directed by Engineer-in-Charge.

S&F in repair Aluminium handles cast type anodised of size 125 mm long ISI marked complete all as specified and as directed by Engineer-in-Charge.

S&F Butt hinges, 100 mm long medium weight, cold rolled mild steel, ISI marked complete all as specified and as directed by Engineer-in-Charge.

S&F in repair Butt hinges, 100 mm long medium weight, cold rolled mild steel, ISI marked complete all as specified and as directed by Engineer-in-Charge.

S&F 150 mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 150 mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified and as directed by Engineer-in-Charge.

S&F 300 mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete.

S&F in repair 300 mm long aluminium alloy anodised sliding door bolt with hasp staple, bolt type, and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy, ISI marked complete.

Supply and fix in repair white vitreous China wash hand basin (Flat back) of size 550 x 400 mm fixed on and including new brackets complete including, 32 mm size brass chromium plated waste coupling, chain and plug and porcelain stopper, etc complete.

Supply and fix in repairs white vitreous china squatting pan ‘ORISSA’ pattern of size 580 mm x 440 mm white with integral foot rests with ‘P’ or ‘S’ trap, front or back inlet including all connection and provision of lime concrete base complete all as specified and as directed..

S&F in repairs white Vitreous china wash down water closet (pedestal pattern) with fixing bolt, Plastic water closet seat cover, white, closed pattern with flat bottom, and cover with aluminium hinging device, brass chromium plated Jet shower with one meter long flexible pipe including all connection complete.

S&F in repairs for 15 mm size angle cock fancy type, cast copper alloy chromium plated, with capston head, screwed down, screwed for iron pipe or for brass ferrule and fixed, all as specified.

S&F in repairs for 15 mm size bib taps fancy type, cast copper alloy chromium plated, with capston head, screwed down, screwed for iron pipe or for brass ferrule and fixed, all as specified.

S&F in repair PVC low level flushing cistern, valve less, syphonic action type, double push bottom, 10 litres capacity with inlet, ball valve float and handle with and including brackets & PVC bend pipe 32 mm dia of required length and making connection complete all as specified.

S&F in repair, PVC flexible waste pipe, 32 mm bore for WHB & sink complete all as specified and directed by Engineer in Charge.

S&F in repair Tubular towel rail stainless steel chromium plated 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls, complete all as specified and as directed by Engineer-in-Charge.

S&F in repair Tubular towel rack (single rack) stainless steel chromium plated 600 mm, including brackets and fixed to walls, complete all as specified and as directed by Engineer-in-Charge. Make:- Jaquar Model No ACN-1181FS or equivalent make mention in Appx A

S&F in repair PVC connection 15 mm size, of length 450 mm, with PTMT nuts complete all as specified and as directed by Engineer-in-Charge

S&F in repair stainless steel chromium plated Peg set of five quality approved by Engr in Charge fixed to wall Complete.

S & F in repairs 15 mm size wall mixer for mixing hot & cold water, cast copper alloy chromium plated with capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge.

M&L for applying 3 mm thick cement base wall care putty in two coats on plastered surface of wall, and making the surface even & smooth for receiving distemper / paint of any description all as specified & directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over one coat of primer all as specified and directed. Note:- Cement base wall care putty where ever directed will be applied and will be measured & paid separately

M&L for preparation of newly plastered surfaces of walls including sides and soffits of beams, fascias, parapets etc and applying two coats of weather proof exterior emulsion paint, over one coat primer colour and tint as ordered, in camouflage pattern, complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden / metal frames or stone, concrete or brick surrounds glazed with oil putty or fixed with beads not exceeding 1.5 Sqm complete all as specified and as directed by Engineer-in-Charge.

S&F 03 mm thick sheet glass, ordinary quality and glazing with oil putty / wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and as directed by Engineer-in-Charge.

S&F 03 mm thick sheet glass, figured glass, pin head type and glazing with oil putty / wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 5 mm thick tinted glass cut to size for aluminium doors / window / partitions and moldings where required open for working purpose fixed with and including rubber beading & Aluminium snap beading complete all as specified and as directed.

Taking down aluminium glazed door shutters of size exc 1.5 Sqm but n. exc 2.0 Sqm (each leaf), & S&F in repair of hard ware fitting such as stainless steel top & Bottom patch, Pivot, tightening of joint and adjustment of floor door spring and refixing shutters in same positioning for smooth functioning complete. Note:- Floor door spring if found unserviceable same will be replaced & will be measured & paid separately under respective item of this BOQ.

S&F in repair door closer aluminium (extruded section body) hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed

Resecuring or easing & adjusting old wooden shutters of any description area exc. 1 Sqm and not exc. 2 Sqm each without taking down shutters, complete all as directed by Engr-in-charge.

M&L for Repair, greasing of steel window area exc. 1.00 sqm and not exc. 3.00 sqm, including welding of hinges replacement of window stay, handle complete all as specified.

M&L for texture finish to wall surface after complete removing existing treatment and applying 3 mm thick acrylic putty, making impression / texture as approved and applying 2 coat Plastic emulsion paint over one coat primer complete as per manufacturer instruction and as directed by Engineer-in-Charge.

M&L for Preparation of old painted steel surfaces of any description exc 10 cm width or girth and painting with one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M&L for Preparation of old decorated surfaces of walls, pillars, cornices by brooming down or steel brushing, scraping down smoke roots. moulds , moss and efflorescence salts, trading oil greasy spots etc. and applying one coat of oil bound distemper after removal of nails & filling nail hole with putty complete all as specified and directed by Engineer-in-charge.

M&L for Preparation of old decorated surfaces of walls, pillars, cornices by brooming down or steel brushing, scraping down smoke roots. moulds , moss and efflorescence salts, trading oil greasy spots etc. and applying two coat of oil bound distemper after removal of nails & filling nail hole with putty complete all as specified and directed by Engineer-in-charge.

Dismantling wall / ceiling boarding of any description fixed in any position with nails complete all as spfd.

M&L for Wooden paneling of second class softwood 12 mm thick with tongue and groove joint fixed in any position over and including wooden framework in second class softwood with plain fillets square or sectional area exc 13 Sqcm and n exc 25 Sqcm at n exc 90 cm centre to centre in both direction and including two or more coat of french polishing on all the exposed surfaces wooden paneling including taking down existing electrical fittings and re-fixing the same, complete.

S&F PVC wall / ceiling paneling consisting of 5 to 8 mm thick hollow type, profile, wall thickness not less than 1 mm, in teak colour, including fixing with solvent cement, and PVC side fixed as per manufacturer instruction complete all as specified & directed. Make:-Royale-Plus a product by German Technology, Decore or equivalent make approve by GE.

Dismantling of false ceiling of any description including cover fillet & snap grid complete all as specified.

M&L for Gl frame work for seamless ceiling comprising of Gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre, intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.

M&L for Providing and fixing Gypsum Board 12 mm thick (water proof) in ceiling fixed with screw or as per manufacturers instructions including necessary jointing and taping, and applying two coat oil bound distemper over one coat primer and 1 mm thick cement base putty complete all as specified and directed by Engr-in-Charge.

S&F false ceiling of Non asbestos fiber cement building designer boards, manufactured from homogeneous mixture of cement, quartz and cellulose and cured with high pressure steam using auto claving process confirming to IS-14862, of size 600 mm x 600 mm x 6 mm thick fixed over and including mild steel galvanised powder coated (minimum thickness of powder coating 50 micron) snap grid frame work of T section (main & cross member) of size 25 mm x 25 mm x 1 mm thick in square pattern of grid size 600mm X 600mm . The aluminium fram work will supported on side wall with the used of mild steel galvanised powder coated 'L' section of size 25 mm x 25 mm x 1 angles etc. Snap grid shall be supported with hangers of 4 mm dia. Galvanised iron wire adjusting level fixed to roof slabs / truss etc by means of ceiling cleats made out of Galvanised iron flat of size 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40 mm long complete all as specified directed by the Engineer-in-Charge.

Dismantling of Plain or corrugated steel sheeting any gauge, thickness, including Nainital or similar pattern roof coverings including ridges, hips, valleys and flashings etc complete all as specified and as directed by Engineer-in-Charge.

S&F pre-painted galvaume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws all as specified.

S&F pre-painted galvaume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof ridges, fixed with self tapping screws as specified, complete all as specified.

S&F 0.63 mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, with L-type or J-type or cranked hook bolts, in roofs, walls etc. with grade of zinc coating 275 complete.

All as per item No 91 but except Sheets using sheet retrieved vide item No 88 above

M&L for tightening bolts and closing bolt holes etc. in old corrugated steel sheets or Aluminium sheeting by sealing with one bitumen and one curved GI washer on either side and 6 mm G.I. bolts and nuts, all set in stiff white lead, bolt n exc 25 mm in length complete all as specified and directed by Engr-in-Charge.

M&L machine cut kota stone slab flooring 20-25 mm thick as in floor, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, laid over and including 20 mm thick screed bed in CM 1:4 complete all as specified and directed by Engineer-in -Charge.

M&L machine cut kota stone slab 20-25 mm thick as in dado / skirting, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, laid over and including 10 mm thick backing coat in CM 1:3 complete all as specified and directed by Engineer-in -Charge.

Demolition of cement concrete (unreinforced) in ground floor and in paving n exc 15 cm thickness (below or above ground level), complete all as specified.

Dismantling wrought iron or mild steel work of any description not other wise provided for.

Excavating in post holes, in soft / loose soil, (or similar holes) each n. exc. 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc. 25cm, watering and removing surplus soil to a distance n. exc. 50 m and making good surfaces complete all as specified.

M&L for PCC 1:3:6 type C 2 using 40mm graded stone aggregate as in foundation, filling, mass concrete complete.

S&F steel work in tubular Post / trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to I.S. 1161-1998 grade St-240 including all necessary work as directed by Engr in Charge. Complete all as specified.

S&F mild steel, plates (Plain or Chequered) Channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment as required FE 410-W (Gde-E-250 quality-A)complete all as specified.

S&F rolled mild steel section as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe 410-W (Gde-E-250 quality A).

M&L for Mild steel, screw bolt machine made with hexagonal or square heads at one end and screwed the other end with washer and one hexagonal or square nut exc 5 cm and n exc 10 cm long and 5 to 10 mm dia. Complete all as specified.

M&L for Preparation of new zinc (or galvanised) steel and iron roof surfaces of any description over 10 cm width or girth to receive painting, by coating with mordant solution including washing and cleaning, etc and applying two coat of synthetic enamel paint over one coat red oxide primer camouflage pattern complete all as specified and directed by Engineer-in-Charge

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified

M&L for 25 mm thick PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in sub base for floor complete all as specified and directed.

S&F in repairs 75 mm size PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified.

S&F in repair 75 mm outer dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with clamp complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair 110 mm outer dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with clamp complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix in repair 500 litres capacity double layer, rotational molded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete

M&L for 75 mm thick PCC type C-2, 1:3:6 (using 40 mm graded stone aggregate) as in plinth protection laid in bays n. exc. 2 sqm each, finishing the surface of concrete topping even & fair, without using extra cement filling the joints with mastic filling comprising of one part of heated bitumen 85/25 or 95/10 grade and 3 parts of sand (all by weight) complete all as specified and as directed by Engineer-in-Charge.

Demolition of interlocking paver block of any description or thickness in floors etc laid, bedded dry, all as specified.

M&L for rubber molded glossy finish Chequered cement concrete tiles of size 30 cm x 30 cm x 25 mm thick, in white cement with pigment, set, jointed in neat cement slurry & pointed in coloured cement, as in floors / path / hard standing, laid over screed bed complete all as specified and directed.

M&L for 100 mm thick cement concrete 1:4:8, type D-2,(using 40 mm graded stone aggregate) as in Sub base for path / flooring complete all as specified and as directed.

M&L for sand cushioning over PCC surfaces, for laying of interlocking tiles, spread rolled and consolidated to gradient as required.

Material & Labour for machine pressed precast concrete interlocking paver block of approved shape and size of 80 mm thickness, with minimum compressive strength of 40 N / Sqmm (M-40 grade), without correction factor for chamfering, made in rubber moulds with 0.50 mm thick scratch proof lacquer coating on top surface, with white cement and pigment laid in path / hard standing complete

Dewatering of septic tank / soakage well of any depth in any position by pumping out and removing outside Military/Defence land by mechanical means (trolley mounted) and burying in pits all as directed including digging of pits in any type of soil and covering pits with earth after absorption of water and including providing and spreading required quantity of bleaching powder around the pit or dispose of waste material as per state protocol including taking down of slab cover and refixing the same CM 1:4 complete all as specified and directed by engineer-in-charge

De-sludging of septic tank of any capacity including connected intercepting chamber, manhole shaft, sludge chamber & filter beds of any description and in any position by pumping out and removing of sludge outside Military/ Defence land by mechanical means (trolley mounted) and burying in pits all as directed including digging of pits in any type of soil and covering pits with earth after filling of sludge and including providing and spreading required qty of bleaching powder or dispose of waste material complete as per state protocol, including taking down of slab cover and placing the same in existing position complete all as specified and directed by Engineer-in-Charge.

Cleaning of 100 mm bore underground sewage pipe (Cleaning length n.exc 30 m from manhole to manhole or from manhole to septic tank) including taking off manhole cover and cleaning of manholes of any size and depth and removing waste material / sludge to a distance of n.exc 300 m and burying in a pit and replacing manhole cover in position after cleaning complete all as specified and directed by Engineer-in-Charge

All as per item No 119 above but 150 mm bore sewage line.

All as per item No 119 above but 200 mm bore sewage line.

M&L for Preparation of old painted surfaces of roof of corrugated steel sheeting and applying one coat of synthetic enamel paint in camouflage pattern to match the colour shade of exist surfaces complete all as directed and as approved by Engineer-in-charge.

M&L for preparation of old plastered surfaces of walls including sides and soffits of beams, fascias, parapets etc and applying one coat of cement base paint, colour and tint as ordered in camouflage pattern, complete all as specified and directed by Engineer-in-Charge.

Taking down copper / aluminium point wiring (light,fan,socket & power) complete incl fixtures and fittings such as switches, ceiling rose, pendent holdes,regulators,sockets, etc and making good disturbed surface of wall, floor etc complete as specified and directed.

Material & Labour for point wiring for one light / Fan point controlled by one, one way switch complete with 1.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed, fire retardant low smoke cable 1100 volts grade ISI marked drawn and including PVC rigid conduit not less than 20 mm dia, including all accessories like bend, tees, junction boxes etc., 1.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed, fire retardant low smoke cable as a earth wire connected to common earth dolly, etc and including sunken type pressed steel terminal box of suitable size for modular type switch with cover plate & frame complete. Note - Colour code of cable Phase-Red Neutral- Black and Earth -Green)

All as per item No 125 above but point wiring for one 5 / 6 Amps socket outlet on independent board controlled by one-way switch.

All as per item No 125 above but point wiring for one 5 Amps socket outlet on same board controlled by one-way switch.

All as per item No 125 above but wiring with 2.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed fire retardant low smoke, cable and 1.5 Sqmm multi-stranded copper conductor PVC insulated, unsheathed fire retardant low smoke, cable as earth wire connected to common earth dolly for 15 Amps multipurpose socket outlet on independent board, controlled with one way switch.

S&F modular one way switch 6 Amp 240 volt marked light / fan suitable for one module etc complete as specified and directed.

S&F Modular 6 Amp 5 pin universal socket suitable for two module , 250 volts complete all as specified and directed.

S&F modular switch one way 16 Amps 240 volts suitable for one module complete as specified and directed.

S&F Modular 6 /16 Amp socket suitable for two module , 250 volts complete all as specified and directed.

S&F modular step type two module fan regulator suitable for 120 watt 250 volts complete as specified and directed.

M&L for ceiling rose with three terminal as per relevant IS complete as specified and directed

S&F fix in repair lamp holder Polycarbonate type with back plate suitable for batten fitting including supply & fixing of 10 watt retrofit LED lamp.

S&F in repair energy efficient LED tube light fitting with built in LED & integral LED driver 18 to 20 watt, channel housing & diffuser of length 1200 mm (approx) with all accessories, fixing arrangement internally pre-wired, fixed in position & connecting complete all as specified and directed by Engg –in-charge.

S&F in repair energy efficient LED tube light fitting with built in LED & integral LED driver 10 watt, channel housing & diffuser of length 600 mm (approx) with all accessories, fixing arrangement internally pre-wired, fixed in position & connecting complete all as specified and directed by Engg –in-charge.

S&F in repair recess mounting 36 watt LED ultra slim ceiling light with extruded aluminium housing and milky diffuser incl suitable size driver and 3 core flexible cord from ceiling rose to connector of fitting etc complete as specified and directed. Make:- CG - Cat No LCTRH-36-TL or equivalent of make mention Appx A

S&F in repair LED 18 watt Square recess mounted LED edge lit slim down light with die-cast aluminum housing finished in premium white powder coating with suitable driver etc complete as specified and directed by Engr-in-charge Make:- CG - Cat No LSCSM-18W-NW or equivalent of make mention Appx A

S&F in repair epoxy powder coated or polystrene insulated material sheet metal enclosure factory made (double door) 4 way TPN (VTP) suitable for MCCB DB's 415 Volts with 200 Amps rated busbar, neutral & earthing link bar, flush/surface mounting complete all as specified and directed.

S&F in repair epoxy powder coated or polystrene insulated material sheet metal enclosure factory made (double door) 8 way SPN suitable for MCB DB's 240 Volts with 200 Amps rated busbar, neutral & earthing link bar, flush/surface mounting complete all as specified and directed

S&F MCB single pole ISI marked ISI Marked `C' series working on 240 Volts 50 HZ AC supply for incoming and out going controlling circuit of capacity 6-32 Amp breaking capacity 10 KA etc all as specified and directed.

S&F MCB single pole and neutral ISI marked `C' series working on 240 volts 50HZ AC supply for incoming & out going controlling system of capacity 63 Amps 10 KA breaking capacity etc all as specified and directed.

S&F MCCB Four pole ISI marked working on 415 volts 50HZ AC supply for incoming & out going controlling system of capacity 100 Amps, 16 KA breaking capacity lcs=100 % lcu etc all as specified and directed.

Material & Labour for sub main wiring with 2 run single core multistranded copper conductor cable, of size 6.0 Sqmm, PVC insulated, unsheathed, fire retardant low smoke, drawn through and including heavy duty rigid PVC conduit not less than 20 mm dia with all necessary fitting and including one run single core multistranded copper conductor cable, of size 6.0 Sqmm, PVC insulated, unsheathed, fire retardant low smoke as earth wire, fixed on wall / ceiling, including taking down old sub main wiring complete. Note: (i) 2 Runs of main cable and one run earth wire with conduit will be measured as one Unit for payment.

M/S GHULAM HASSAN AND SONS

M/S GULZAR ENTERPRISES

NAJAR ENTERPRISES

M/S GULAM AHMAD ABDUL SAMAD