Construction of Permanent building of Composite Regional centre CRC including Civil,Electrical , Plumbing and others Internal and External services at Jamdoli,Agra Road,Jaipur,Rajasthan

S.No. Description Total Amount(In Rs)

BILL OF QUANTITIES

S.No. DESCRIPTION OF ITEM UNIT QTY RATE(Rs) Amount (Rs)

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm

in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto

50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil

Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of

5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches,

2 2.25a plinth, sides offoundation etc. complete for all lift.

Filling available excavated earth (excluding rock) in trenches, plinth, sides

of foundations etc. in layers not exceeding 20cm in depth, consolidating

2.25 each deposited layer by ramming and watering, lead up to 50 and for all lift.

Surface dressing of the ground including removing vegetation and in-

2.28 equalities not exceeding 15 cm deep and disposal of rubbish, lead up to

50 m and lift up to 1.5 m.

2.28.1 All kinds of soil sqm 4000 34.15 136600.00

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -

All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources :

8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement

concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /

Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /

retard setting of concrete, to improve durability and workability without impairing strength; including pumping of

concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and

5 5.33 reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.

In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the

contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All works upto plinth level Concrete of M25 grade with minimum cement

5.33.1 content of 330 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement

concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /

Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /

retard setting of concrete, to improve durability and workability without impairing strength; including pumping of

concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and

6 reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately.

In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the

contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330

5.33.2 kg /cum

7 5.9 Centering and shuttering including strutting, propping etc. and removal of form for :

5.9.1 Foundations, footings, bases of columns, etc. for mass concrete sqm 121.00 392.15 47450.15

5.9.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.9.3 Suspended floors, roofs, landings, balconies and access platform

5.9.4 Shelves (Cast in situ) sqm 100.00 927.25 92725.00

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers sqm 2894.00 736.40 2131141.60

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts sqm 1199.00 961.30 1152598.70

5.9.16.1 Edges of slabs and breaks in floors and walls Under 20 cm wide metre 1182.00 208.55 246506.10

5.9.19 Weather shade, Chajjas, corbels etc., including edges

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth

in: Cement mortar 1:6 (1 cement : 6 coarse sand) cum 300.00 7132.25 2139675.00

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above

9 6.4.2 plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above

10 6.13.2 plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry

100 mm/ 125 mm thick with Grade-1 AAC blocks of density 551 to 650

kg/cum conforming to IS:2185 (Part 3) in super structure above plinth

a 6.38 level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ).

The rate includes providing and placing in position 2 Nos 6 mm dia M.S.

bars at every third course of masonry work.

Digitally signed by ARUN

Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry

with 150 mm to 300 mm thick with Grade-1 AAC blocks of density 551 to

650 kg/cum conforming to IS:2185 (Part 3) in super structure above plinth

level up to floor V level with RCC band at sill level and lintel level with

approved block laying polymer modified adhesive mortar all complete

as per direction of Engineer-in-Charge. (The payment of RCC band and

reinforcement shall be made for seperately).

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per

12 4.13 square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly

soaked in kerosene oil.

13 2.34 Supplying chemical emulsion in sealed containers including delivery as specified.

2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% litre 659.00 234.75 154700.25

Diluting and injecting chemical emulsion for Pre-CONSTRUCTIONAL anti-termite treatment (excluding the

14 2.35 cost of chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including

2.35.3 drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the

existing floor :

13 2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all

complete upto plinth level & above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-

chambered frame, sach and mullion/coupler (where ever required) extruded profiles having minimum wall

thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm foe series R3 and R4 profiles conforming to EN :

12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape &

size as per CPWD Specification, uPVC extruded glazing beads, interlocks and inline sash adaptor (where ever

15 9.147.A required) of appropriate dimension, EPDm gasket , hardware, SS 304 grade fasteners of minimum 8 mm dia with

countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS

1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash &

mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners,

including drilling of holes for fixing haedware and drainage of water etc.

After Fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof sillicon

sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD

specification & direction of Engineer-in-charge. Section of steel reinforcement and cross sections of uPVC Profiles

to be as per design approved by Engineer-inCharge. Wire mesh/Glazing of plain/toughened/ laminated /double

glass unit with / without high performance coatings as per design requirements and conforming to IS :3548 & IS :

16231 shall be paid separately. Notes:- Structural design proof cheacked from a Government

Engineering Institute, to be provided by the manufacturer for :

(i) Sites with basic wind speed >45 m/Sec as per IS 875 - Part 3. (ii) Sites with structure height more than 20m for

all wind speeds.

Two track two panels sliding door with Aluminium channel for roller track, wool pile, zinc alloy (zamak) powder

coated handle on two panels along with multi-point locking system, adjustable nylon rollers with SS 304 body.

9.147.A1.2 Using R3 series with frame (55 mm & above)x (40 mm & above) & sach (30 mm & above ) x (55 mm &

above).(Height upto 1.8 metre).

Two track two panels sliding door with Aluminium channel for roller track, wool pile, zinc alloy (zamak) powder

coated handle on two panels along with multi-point locking system, adjustable nylon rollers with SS 304 body.

9.147.B1.2 Using R4 series with frame (64 mm & above)x (45 mm & above) & sach (44 mm & above ) x (85 mm &

above).(Height above 2.5 metre).

16 9.1.2 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and

fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener

shall be paid for separately).Sal wood cum 8.00 116520.30 932162.40

Providing and fixing ISI marked flush door shutters conforming to IS :

2202 (Part I) decorative type, core of block board construction with

frame of 1st class hard wood and well matched teak 3 ply veneering with

vertical grains or cross bands and face veneers on both faces of shutters.

9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges

with necessary screws SQM 262.00 3473.85 910148.70

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door

18 9.23 shutters (over all area of door shutter to be measured).

Steel work welded in built up sections/ framed work, including cutting,

10.25 hoisting, fixing in position and applying a priming coat of approved steel

primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets,

gates and similar works Kg 4000.00 172.60 690400.00

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including

welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with

necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel

19 10.28 dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with

suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel

members shall be considered excluding fixing accessories such as nuts, bolts, fasteners

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish

with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046

20 9.127.1 Type S, including cost of adhesive of approved quality

Digitally signed by ARUN

Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and

wooden plugs and embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6

graded stone aggregate 20mm nominal size). Nos. 488.00 228.85 111678.80

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC

22 9.96.1 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16

Providing and fixing aluminium tower bolts, ISI marked, powder coated (minimum thickness of powder coating

23 9.97 50 micron) transparent or dyed to required colour or shade, with necessary screws etc. complete : 250x10 mm.

Providing and fixing aluminium handles, ISI marked, powder coated (minimum thickness of powder coating 50

24 9.100.1 micron) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than

grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc.

25 9.101.2 complete. Twin rubber stopper

Providing and fixing chromium plated brass curtain rod having wall

thickness of 1.25 mm with two chromium plated brass brackets fixed with

a 9.46 C.P. brass screws and PVC sleeves etc., wherever necessary complete

Providing and fixing aluminium die cast body tubular type universal

hydraulic door closer (having brand logo with ISI, IS : 3564, embossed

c 9.83 on the body, door weight upto 35 kg and door width upto 700 mm), with

necessary accessories and screws etc. complete.

Providing and fixing bright finished brass hanging type floor door stopper

with necessary screws, etc. complete.

Providing and fixing fire resistant door frame of section 143 x 57 mm

having built in rebate made out of 16 SWG G.I. sheet (zinc coating not

less than 120 gm/sqm) duly filled with vermuculite based concrete mix,

suitable for mounting 60 minutes fire rated door shutters. The frame is

fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround

the frame and fixing with dash fastener of approved size and make,

including applying a coat of approved brand fire resistant primer etc.

complete as per direction of Engineer-in-charge (Dash fastener to be

paid for separately).

Providing and fixing 50 mm thick glazed fire resistant door shutters of 60

minutes fire rating conforming to IS:3614 (Part-II), tested and certified as

per laboratory approved by Engineer-in-charge, with suitable mounting

on door frame, consisting of vertical styles, lock rail, top rail 100 mm

f 9.137 wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc

coating not less than 120 gm/sqm) duly filled FR insulation material and

fixing with necessary stainless steel ball bearing hinges of approved

make, including applying a coat of approved fire resistant primer etc. all

complete as per direction of Engineer-in-charge (panneling to be paid for

separately). each 10.00 7533.20 75332.00

Providing and laying integral cement based water proofing treatment including preparation of surface as required

for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat

cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and

approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including

cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to

115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound

26 22.7 conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5

(1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by

Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including

rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed

with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the

surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water

proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth

of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and

making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water

for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as

directed and specified by the Engineer-in-Charge :

With average thickness of 120 mm and minimum

22.7.1 thickness at khurra as 65 mm. sqm 450.00 1684.60 758070.00

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm

x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof

and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1 :4 (1 cement : 4 coarse

sand) and grouting the joints with mix of white cement & marble powder in ratio of 1 :1, including rubbing and

27 12.55 polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet

walls in the same manner.

28 13.4.2 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)

Digitally signed by ARUN

29 13.5 15 mm cement plaster on the rough side of single or half brick wall of mix :

15 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) in single coat on rough side of single or half brick

8 mm cement plaster in two coats under layer 12 mm thick cement plaster

13.12 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster

1:3 (1 cement : 3 coarse sand) finished rough with sponge. sqm 2000.00 537.45 1074900.00

31 13.16.1 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

32 5.30 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. metre 12183.00 78.40 955147.20

B 5.30 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. metre 470.00 78.40 36848.00

Chequerred precast cement concrete tiles 22 mm thick in footpath &

courtyard, jointed with neat cement slurry mixed with pigment to match

the shade of tiles, including rubbing and cleaning etc. complete, on 20

mm thick bed of cement mortar 1 :4 (1 cement: 4 coarse sand).

Medium shade pigment using 50% white cement 50% Grey

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water

absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on

34 11.41A 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm

including grouting the joints with white cement and matching pigments etc., complete.

11.41A.1.2 Double Charge Size of Tile 800 x 800mm

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300

mm or more (thickness to be specified by the manufacturer), of 1st quality

conforming to IS : 15622, of approved make, in all colours, shades,

except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement

Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @

3.3 kg/ sqm including pointing the joints with white cement and matching

pigments etc., complete.

Providing edge moulding to 18 mm thick marble stone counters, Vanities

8.3 etc., including machine polishing to edge to give high gloss finish etc.

complete as per design approved by Engineer-in-Charge.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water

absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on

35 11.41A 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm

including grouting the joints with white cement and matching pigments etc., complete.

11.41A.3.2 Glazed Vitrified tiles Matt/Antiskid finish of size 600 x 1200mm

Providing and laying Polished Granite stone flooring in required design

and patterns, in linear as well as curvilinear portions of the building all

complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement

36 11.56.1 mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry

admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified

and as directed by the Engineer-in-Charge.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for

kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade,

colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with

white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing

to edges to give high gloss finish etc. complete at all levels.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the

manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as

approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3

38 8.31 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white

cement mixed with pigment of matching shade complete.

Providing and laying damp-proof course 40 mm thick with cement

concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural

sources : 4 graded stone aggregate 12.5 mm nominal size derived from

38 a 4.10 natural sources)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded

stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed

and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the

39 4.17 top smooth.

Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 40 mm wide and 4 mm thick

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of

41 13.41 approved manufacturer and of required shade and colour all complete to achieve even shade and colour :

New work (two or more coats) over and including water

13.41.1 thinnable priming coat with cement primer having VOC content less than 50 gram/litre sqm 1100.00 185.65 204215.00

Wall painting with premium acrylic emulsion paint of interior grade, having

13.83 VOC (Volatile Organic Compound ) content less than 50 grams/ litre of

approved brand and manufacture, including applying additional coats

wherever required to achieve even shade and colour.

Digitally signed by ARUN

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:

42 13.47.1 New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and

43 13.80 manufacturer, over the plastered wall surface to prepare the surface even and smooth Complete.

French spirit polishing :

a 13.68 13.68.1 Two or more coats on new works including a coat of wood filler

Painting with synthetic enamel paint of approved brand and manufacture

b 13.61 to give an even shade :

13.61.1 Two or more coats on new work

Construction of Apron drain of size 150mm x 150mm with 115 mm brick wall in 1:6 (1 cement : 6 coarse sand)

having palstered with 20 mm thick Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of

neat cement & 150 mm thick lean concrete base in 1:4:8 (1 cement : 4 coarse sand : 8 Stone Grit) and 25 mm thick

cement concrete in 1:2:4 (1 cement : 2 coarse sand : 4 Stone Grit) above lean concrete with floating coat etc.

complete incl. cost of all etc. required for proper completion of work.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse

sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with

12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making

45 12.22 and finishing the outlet complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A,

46 12.41 including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single

socketed pipes.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC

47 12.42 rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382,

leaving 10 mm gap for thermal expansion.

12.42.1 Coupler

12.42.6 Shoe (Plain)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by

means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick

work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less

Providing and laying in situ seven course water proofing treatment with

APP (Atactic Polypropylene) modified Polymeric memberane over roof

consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th

& 6th courses of bonding material @ 1.20 kg/sqm, which shall consist of

blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th

layers of roofing membrane APP modified Polymeric membrane 2.0 mm

thick of 3.00 Kg/sqm weight consisting of five layers prefabricated with

49 a 14.88 centre core as 100 micron HMHDPE film sandwiched on both sides with

polymeric mix and the polymeric mix is protected on both side with 20

micron HMHDPE film. 7th, the top most layer shall be finished with brick

tiles of class designation 10 grouted with cement mortar 1:3 (1 cement : 3

fine sand) mixed with 2% integral water proofing compound by weight of

cement over a 12 mm layer of cement mortar 1:3 ( 1 cement : 3 fine sand)

and finished neat (item of laying brick tiles shall be paid for separately).

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry

mixed with water proofing cement compound consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm.

This layer will be allowed to air cure for 4 hours.

50 22.5 (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126

kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

(The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and

masonry with polymer mixed slurry.)

Providing and fixing GI Clip in Metal Ceiling System of 600x600 mm

module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted

steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre,

suspending the main C carrier of size 10x38x10 mm made of GI steel 0. 7 mm thick from the soffit with the help of

soffit cleat 37x27x25x1 .6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier

bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of

GI steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers

51 12.54.2 with the help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T

connectors have to be used. All sections to be galvanized@ 120 gms/sqm (both side inclusive), fixing with clip in

tiles into spring T with : GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and

0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive)

and 20% perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester powder coated

of thickness 60 microns (minimum), including factory painted after bending and perforation.

Digitally signed by ARUN

16.1 Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating

earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making

good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

16.2 Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of

the maximum dry density (proctor density). 24.85 1491.00

16.3.1 Supplying and stacking at site.90 mm to 45 mm size stone aggregate Cu.M 60.00 2098.4 125904.00

16.3.2 63 mm to 45 mm size stone aggregate. Cu.M 60.00 1636.05 98163.00

16.3.3 53 mm to 22.4 mm size stone aggregate. Cu.M 60.00 1842.3 110538.00

16.4 Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform

thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity in stages to proper

grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of

coarse aggregate, watering and compacting to the required density . 1046.95 261737.50

16.43.1 Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement

content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate

proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever

required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling

to required slope/ camber, finishing with required texture, including steel Cu.M 55.00

form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction &

longitudinal joints ( 10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with

approved joint filler and sealants, complete all as per direction of Engineerin- charge (Item of joint fillers, sealants,

dowel bars with sleeve/ tie bars to be paid separately). 10529.35 579114.25

16.48.1 Painting road surface marking with adequate nos of coats to give uniform finish with ready mixed road marking

paint conforming to IS : 164, on bituminous surface in white/yellow shade, including cleaning the surface of all Sq.M 100.00

dirt, scales, oil, grease and foreign material etc. complete. New work (Two or more coats) 288.9 28890.00

16.50 Providing and fixing Glow studs of size 100x20 mm made of heavy duty body shall be moulded ASA (Acrylic

styrene Acryloretrite ) or HIP (High impact polystyrene) or ABS having electronically welded micro- prismatic lens

with abrasion resistant coating as approved by Engineer in charge. The glow stud shall support a load of 13635

kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35 (+/-5) degress to

base .The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance Each 80.00

intensity should be as per the specification and shall be tested as described in ASTM I: 809 as recommended in

BS: 873 part 4 : 1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per

procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge.

16.59.1 Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to

be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type -

IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-

lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall

be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with

suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm

along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a ertical

post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the Sq.M 50.00

bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required

size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of

approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be

painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy

paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing ,

specification and direction of Engineer—in-charge.

4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and

shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

16.60.1 Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium

sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective

sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-incharge, letters, borders etc. as

per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate

by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of

ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium

alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows Sq.M 90.00

along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey

colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of

rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same

in position all complete as per drawings, specification and direction of the engineer-in-charge.(Structural frame

work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for

16.63 Providing, laying and making kerb channel 30cm wide and 50mm thick with cement concrete 1:3:6 (1 cement: 3

coarse sand:6 graded stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40 mm nominal

size well rammed and consolidated and grouted with fine sand including finishing the top smooth etc. complete

and as per direction of Engineer-in-charge. 558.3 72579.00

16.68 Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by

block making machine with strong vibratory compaction, of approved size, design & shape, laid in required

colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand Sq.M 550.00

etc. all complete as per the direction of Engineer-in-charge.

16.69 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position

to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand) including

making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm),

including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge

(length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by

Engineer-in-charge). 10117.6 505880.00

19.6.2 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of

cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm R.M 100.00

Horticulture Supplying and stacking of good earth at site including royalty and carriage upto 1 km (earth measured in stacks

and Land will be reduced by 20% for payment).

Horticulture Spreading of sludge, dump manure and / or good earth in required thickness as per direction of Officer-in-

and Land charge (Cost of sludge, dump manure and / or good earth to be paid separately).

Total of Schedule Items 115961207.48

HORTICULTURAL WORKS

2.1 Trenching in ordinary soil upto a depth of 60 cm including removal and stacking of serviceable materials and

then disposing of by spreading and neatly levelling within a lead of 50 m and making up the trenched area to

proper levels by filling with earth or earth mixed with sludge of/and manure before and

after flooding trench with water (encluding cost of imported earth,sludge or manure). 119.00 95200.00

2.2 Supplying and stacking of good earth at site including royalty but excluding carriage (earth measusred in stacks

will be reduced by 20% for payment). 803.75 643000.00

2.4.3 Supplying and stacking a' site dump manure from approved

source, excluding carriage (manure measured in stacks will be Cu.M 46.25

reduced by 8% for payment)Screened through sieve of l.S. designation 4.75 mm 491.65 22738.81

2.5 Rough dressing the trenched ground including breaking clods. Sq.M 1850.00 2.3 4255.00

2.6 Uprooting weeds form the trenched area after 10 to 15 days of

its flooding with water including disposal of uprooted vegetation. 7.45 13782.50

2.7 Fine dressing the ground Sq.M 1850.00 5.6 10360.00

Digitally signed by ARUN

2.8 Spreading of sludge, dump manure or/and good earth in

required thickness (Cost of sludge, dump manure or/and good Cu.M 1156.25

earth to be paid separately). 79.7 92153.13

2.9 Mixing earth and sjudge or manure in porportion specified or directed. Cu.M 1156.25 55.7 64403.13

2.10.1 Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more tili the grass

forms a thick lawn free form weeds and fit for mowing including supplying good earth if needed.In rows 15 cm Sq.M 1500.00

apart in either direction. 26.95 40425.00

2.14.1 Digging holes in ordinary soil and refilling the same with excavated earth mixed with manure or sludge in the ratio

of 2:1 by volume (2 parts of stacked volume of earth after reduction by 8%) flooding with water, dressing

including removal of rubbish and surplus earth. if any with all leads and lifts (cost of manure, sludge or extra good

earth if needed to be paid for separately):Holes 1.2M dia, and 1.2m deep 362.75 11608.00

2.14.2 Holes 60 cm dia. And 60 cm deep Nos 64.00 155.5 9952.00

2.16 Providing and fixing M.S. flat iron tree guard 60 cm dia. And 2m high above ground level formed of 4 nos. 25x6

mm and 8 nos. 25x3 mm vertical M.S. flats hvetted to 3 nos. 25x6 mm M.S. flat iron rings in two halves, bolted

together with 8mm dia. And 30 mm long bolts inclujding painting two coats with paint of approved brand and

manufacture over a coat of priming complete in all respects. 6507.55 325377.50

2.19.1 Edging with bricks laid dry length wise including excavation, refilling, consolidating with hand packing and

spreading susrplus earth neatly within a lead of 50m.Common burnt clay F.P.S. (non modular) bricks of class R.M. 350.00

designation 7.5 48.85 17097.50

2.11 Renovating lawns including weeding, cheeling the grass, forking the grond, top dressing with sludge or manur,

mixing the same with forked soil, watering and maintaining the lawn for 30 days or more till the grass forms a

thick lawn free from weeds and fit for mowing and disposal of rubbish as directed, including supplying good

earth if needed but excluding the cost of sludge or manure. 52.45 52450.00

2.12 Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other

growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh

growth after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all

leads and lifts. 92.9 92900.00

2.13 Preparation of beds for headging and shrubbery by excavating 60 cm deep and treanching the excavated base

to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in

the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge

or manure after reduction by 8%) flooding with water, filling with earth if necessary, watering and finally fine Cu.M 40.00

dressing, levellinjg etc. including stacking and disposal of materials declared unserviceable and surplus earth

upto 1.5m complete (cost of sludge, manure or extra earth to be paid for separately).

Total of Schedule Items 1509296.57

1.0 SCHEDULE OF QUANTITIES

S. No. Description of Item Qty. Unit Rate Amount

Supply, Installation, Testing & Commissioning of

following accessories suitable for upgradation of

existing Sewage Treatment Plant of 50 KLD with

Advanced Eco Reactor (AER) Technology:-

b) BOD : upto 100 mg/l

c) Suspended solids (SS) : upto 100 mg/l

d) Oil & grease : upto 10 mg/l

e) COD : upto 250 mg/l

(B) Effluent (Final)

a) BOD : Not more than 10 mg/l

b) Fecal Coliform : Not more than 230 (MPN/100)

c) Total Suspended Solids : Not more than 20mg/l

e) COD : Not more than 50 mg/l

(C) The plant should be able to operate efficiently at

10% of design flow and should be suitable for

(D) There should be no daily/weekly/monthly sludge

1 Pre Treatment

1.1 Bar Screen Chamber

SITC of Coarse Type SS Bar Screen (SS 304 fabricated)

of size 700MM X 600MM with 10MM-12MM

opening along with SS Frame for lifting to block the in

organics like bottles, glass, polythenes etc complete as

(MOC - SS 304, Fabricated) Each 2 46891 93782.00

2 Secondary Treatment

SITC ofPumps for transferring

submersible sewagepumps

Sewage Transfer to AER(Motor

Capacity: 1.0 HP) suitable for handling upto 20mm

solid particles having a liquid discharge rate of 2500

Ltr/hr (each) at a head of 12 metres incorporating C.I.

casing, CI impeller, CI motor body with Nylon lifting

rope 16mm-20mm thick and suitable for operation on

3-phase 415- Volt AC supply with similar

3 Nos Pump - [02 Working + 01 SB] complete etc. as

2.2 Living Soil Medium

Supply of 200 kgs of living soil medium; a specialized

microbe pre-treated media formulated using specially

bred catalyst culture, sugar & protein source, and

fermented for 24 hrs, sun dried, sieved and packed for

creating required ecosystem in the Advanced Eco

Reactor including providing technical know-how for

project execution.

2.3 Organic Biosorption Media

Digitally signed by ARUN

SITC of 4 tons of Organic biosorption media consisting

of carbon rich material along with unloading & filling

into the Advanced Eco Reactor.

2.4 Plastic Crates

SITC of Plastic Crates for housing of living soil medium

and organic bioadsorption media

Unit Size : 520 mmX 360mm X 280 mm; MOC:

Recycled Plastic Each 180 725 130500.00

2.5 Green Zoning

SITC of planting material, growth promoters and

enhancers etc for green zoning Job 1 108368 108368.00

2.6 Probiotic Bacterial culture

Supply & inoculation of probiotic microbial mother

culture for development of microbial bio-film on the

surface of the inert media and for control of sludge

during operation period.

Digitally signed by ARUN

SITC of ASTM approved UPVC Sch 40 Piping work for

with all necessary accessories like ball valves, b/f

valves, elbow, unions, flange, Non returnable valves

MTA, FTA, coupler, tees, reducers, pressure gauge,

clamps, fastners etc for making the AER grid complete

as required along with 02 no. helix disc filter and ISI

marked PVC pipe for taking the AER outlet into the UG

4 Electrical Work

4.1 STP Control

SITC Panel Motor Control Panel made of 2mm

thick CRCA sheet duly powder coated with necessary

switch gears such as INCOMER MCCB of required amp

with outgoing switch gears for auto operation of 02 no.

sewage pumps, 1 Nos. Ozonation System, 02 nos.

Treated water pumps along with necessary MCBs, VIF

meter, indication light, protection MCB and DOL

Starter with MCB over load relay, Single Phase

Preventer relay, on-off light push button, auto - manual

selector switch, cyclic timer for auto change-over of

pumps, dry run protection.

4.2 Unarmoured/Flexible Copper Control Wiring

SITC of unarmoured/flexible Copper control wiring of

suitable size in pvc channel/conduit/MS pipe from STP

panel to all the pumps and other electrical equipments

complete as required.

5 Instrumentation

SITC of online pH meter to measure acidity or alkanity

of the treated water etc. as required.

5.2 Flow Meter

SITC of Electromagnetic Flow meter suitable for flow

rate of 50 KLD plant treated water complete as reqd.

5.3 Float switch

SITC of baloon type PP liquid water level controller for

all pumps to ensure respective pumps start/stop

automatically to prevent any unwanted

overflow/damage of pumps with 3 mtrs wire complete

6.1 Ozonation System for Disinfection

Ozone generation system (capacity 50 gms) with

recirculation system including recirculation CPVC

piping & recirculation pump with servo stabiliser for

disinfection & polishing of waste water.

7 Treated water pumps for transferring treated

SITC foropenwell

non-potable use

submersible pumps (Motor Capacity:

7.1 2.0 HP) having a liquid discharge rate of upto 8000

Ltr/hr (each) at a head of 24 metres incorporating C.I.

casing, CI impeller, CI motor body with Nylon lifting

rope 16mm-20mm thick and suitable for operation on

3-phase 415- Volt AC supply with similar

2 Nos Pump - [01 Working + 01 SB] complete etc. as

SUB HEAD-: II (Operation & Maintenance of 100 KLD STP based on Advanced

Eco Reactor (AER) Technology)

8 O&M for 12 Months

8.1 SITC of PVC tank (capacity: 1000 litres) fitted with ball

valve and dosing pipe for dosing of activated bacterial

culture in the collection tank

Operation & preventive maintenance of STP by 01 no. Each 2 20476 40952.00

8.2 operator all days in a month (8.5 hrs shift). The cost

a. Operation of STP

b. Dosing of activated probiotic bacterial culture (100

d. Mainentenance of STP log book and dosing register

e. Repair & maintenance i/c replacement of defective

parts i/c rewinding of motor, repair of pump, pipe,

panel or any other electrical or mechanical equipment

Digitally signed by ARUN

Detailed Estimate Based On DSR-2022 ,DSR 2025 and Market Rate

Internal Electrical Works

Rate as Amount as Amount as

per DSR Rate as Per Amount as per

Sr.No. Sch.No. Particulars Qty Unit per DSR per DSR Per

2025(Rs Market(Rs) DSR 2022(Rs)

2022(Rs) 2025(Rs) Market(Rs)

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed medium class PVC

1 1.10.3 conduit, with modular switch, modular plate, suitable GI box 672 Nos. 1,467.00 - 9,85,824.00 -

and earthing the point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable etc. as required.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface /

recessed medium class PVC conduit, 2 way modular switch,

2 1.11 modular plate, suitable GI box and earthing the point with 1.5 16 Nos. 1,562.00 - 24,992.00 -

sq.mm FRLS PVC insulated copper conductor single core cable

etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/

recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC

3 1.12 insulated copper conductor single core cable for loop earthing as required. 5565 Meter 334.00 - 18,58,710.00 -

Wiring for circuit/ submain wiring alongwith earth wire with the

following sizes of FRLS PVC insulated copper conductor, single core cable in

4 1.14 surface/ recessed medium class PVC conduit as required. - - -

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Supplying and drawing following pair 0.5 mm dia FRLS PVC

insulated annealed copper conductor, unarmored telephone

5 1.18 cable in the existing surface/ recessed steel/ PVC conduit as - - -

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper

conductor PE insulated, shielded with fine tinned copper braid and protected with

6 1.19 PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. 385 Meter 47.00 - 18,095.00 -

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

7 1.21 cutting the wall and making good the same in case of recessed - - -

conduit as required.

Supplying and fixing following modular switch/ socket on the

existing modular plate & switch box including connections but

excluding modular plate etc. as required.

a 1.24.6 Telephone socket outlet 19 Each 148.00 - 2,812.00 -

b 1.24.7 TV socket outlet 7 Each 148.00 - 1,036.00 -

c RA-1 RJ45 socket cat 6 with shutter 84 Each 497.46 - - 41,786.82

Supplying and fixing two module stepped type electronic fan

9 1.25 regulator on the existing modular plate switch box including 202 Each 369.00 - 74,538.00 -

connections but excluding modular plate etc. as required.

Supplying and fixing following size/ modules, GI box alongwith

10 modular base & cover plate for modular switches in recess etc. - - -

Supplying and fixing suitable size GI box with modular plate and cover in front

on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket

11 1.31 outlet and 5/6 A modular switch, connections etc. as required. 139 Each 477.00 - 66,303.00 -

Supplying and fixing suitable size GI box with modular plate and cover in front

12 1.32 on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A 96 Each 586.00 - 56,256.00 -

modular socket outlet and 15/16 A modular switch, connections etc. as required.

Installation ,Testing, Commissioning of wall bracket /ceiling

fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per

13 1.35 fitting, complete with all accessories including connections etc. as required. 0 Each 119.00 - - -

Digitally signed by ARUN

Supplying and fixing stiff pendent with 300 mm long, 20 mm dia X 1.6 mm thick

steel conduit, aluminium cast back plate and brass holder complete, including

14 1.36 wiring the down rod with 1.5 sq. mm FRLS PVC insulated, copper conductor, Each 304.00 - - -

single core cable and painting etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase,

15 1.38 230 V, complete as required. 20 Each 99.00 - 1,980.00 -

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/

16 1.53 recessed Steel/ PVC conduit as required. - - -

Wiring for group controlled (looped) light point/fan

point/exhaust fan point/ call bell point ( without independent

switch etc.) with 1.5 sq. mm FRLS PVC insulated copper

17 1.55 conductor single core cable in surface/ recessed PVC conduit, - - -

and earthing the point with 1.5 sq. mm FRLS PVC insulated

copper conductor single core cable etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front

on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular

socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For

light plugs to be used in non residential buildings).

Supplying & fixing suitable size GI box wih modular plate and

cover in front on surface or in recess including providing and

19 1.57 fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve 63 Each 727.00 - 45,801.00 -

including connections, painting etc. as required.

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

surface/ recess, complete with tinned copper bus bar, neutral

20 2.4 bus bar, earth bar, din bar, interconnections, powder painted - - -

including earthing etc. as required. (But without

MCB/RCCB/Isolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature

circuit breaker suitable for inductive load of following poles in the existing MCB

21 2.10 DB complete with - - -

connections, testing and commissioning etc. as required.

c 2.10.5 Three Phase & Neutral 8 Each 1,228.00 - 9,824.00 -

Supplying and fixing following rating, double pole, (single phase

and neutral), 240 V, residual current circuit breaker (RCCB),

22 2.14 having a sensitivity current 30 mA in the existing MCB DB - - -

complete with connections, testing and commissioning etc. as

Supplying and fixing 63Amp, four pole, (three phase

and neutral), 415 volts, residual current circuit breaker (RCCB),

23 RA-3 having a sensitivity current 300 mA in the existing MCB DB 2 Each 6,026.70 - - 12,053.40

complete with connections, testing and commissioning etc. as

required. Similar to Legrand or equivalent.

Supplying and fixing 40/63A rating, 415 V, 10 kA, "C" curve, miniature circuit

breaker suitable for inductive load of Four poles in the existing MCB DB

24 complete with connections, testing and commissioning etc. as required. Similar 9 Each 2,657.56 - - 23,918.06

to Legrand DX3 AC MCBs or equivalent.

Supplying and installing following size of perforated painted

with powder coating M.S. cable trays with perforation not more than 17.5%, in

25 4.1 convenient sections, joined with connectors, suspended from the ceiling with M.S. - - -

suspenders including bolts & nuts, painting suspenders etc as required.

a 4.1.1 100 mm width X 50 mm depth X 1.6 mm thickness 100 Each 543.00 - 54,300.00 -

b 4.1.4 300 mm width X 50 mm depth X 1.6 mm thickness 100 Each 777.00 - 77,700.00 -

c 4.1.7 600 mm width X 50 mm depth X 1.6 mm thickness 30 Each 1,366.00 - 40,980.00 -

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick

26 5.4 including accessories, and providing masonry enclosure with 4.0 Each 7,472.00 - 29,888.00 -

cover plate having locking arrangement and watering pipe of

2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm

thick including accessories, and providing masonry enclosure

with cover plate having locking arrangement and watering pipe

of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre

below ground as strip earth electrode, including connection/

28 5.9 terminating with G.I. nut, bolt, spring, washer etc. as required. 150.0 Meter 144.00 - 21,600.00 -

(Jointing shall be done by overlapping and with 2 sets of G.I. nut

bolt & spring washer spaced at 50mm)

Digitally signed by ARUN

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre

below ground as strip earth electrode, including connection/

29 5.8 terminating with nut, bolt, spring, washer etc. as required. 50.0 Meter 972.00 - 48,600.00 -

(Jointing shall be done by overlapping and with 2 sets of brass

nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I.

30 5.1 pipe from earth electrode including connection with brass nut, 100 Meter 1,551.00 - 1,55,100.00 -

bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.

pipe from earth electrode including connection with G.I. nut,

bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in

32 5.15 recess for connections etc. as required. 100 Meter 244.00 - 24,400.00 -

Providing and fixing 6 SWG dia G.I. wire on surface or in recess

for loop earthing along with existing surface/ recessed conduit/

submain wiring/ cable as required.

LED Down lighter (SMD Type) (System lumen efficacy >135 lm/Watt)

Supplying, installation, Testing & Commissioning of LED Recessed /

surface Down lighter (Round /square/Rectangular) SMD type of following body

material with PMMA and prismatic diffuser and construction as per IS : 10322

with driver as per the requirement with Driver efficiency >85%, Operating

voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range - 15 deg to 40

deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit

protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare

Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver

DSR & electrical circuitry), life time of minimum 50000 Burning Hours with , 70% of

2025 initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 - -

1.3 report, CCT 3000°K / 4000°K / 5700°K / 6000°K /6500°K (As per ANSI Bin) ,

SDCM(Standard Deviation Color Matching) <3, Maximum power consumption

should not more than the specified rating and Fixture shall be of relevant BIS

standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name

Engraved/ Embossing/ Screen printing on housing. OEM must have its own in

house NABL lab setup for all testing facilities for LED fixtures. complete in all

respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor

single core cable and earthing etc. as required

with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt

output . LM79 & LM80 Test report from NABL lab for all testing required for

LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as

approved by Engineer-in-Charge as per requirement. (Thermal management: heat

sink of aluminum housing such that LED junction temperature shall not rise

Powder coated die cast / Extruded aluminum Body including trim.

SITC of 12W Extruded aluminium batten available in 2ft run length with

multiple lumen packages and suitable for surface, wall & conduit ounting (with

accessories). similar to Philips Type HSN Code MRP (INR) BN 021 LED12S

6500 PSU GR or equivalent.

Supply and fixing of water tight oblong 10 Watt LED bulkhead luminaire having

pressure diecast housing with driver set confirming to IP 65 and above Protection,

IK08, High purity / transmisivity UV stablized Non yellowish diffuser/ Reflector for

uniform light distribution, ditachable driver set, suitable for 24hrs continuous operation

complete in all respect.

1200 system lumen, >120lm/W, PF>0.95, CRI>70, >300V, over voltage protection,

4KV internal surge protection with 5 year warrenty. CAT-AAA

Digitally signed by ARUN

LED Batten light (System lumen efficacy >135 lm/Watt)

Supplying, installation, Testing & Commissioning of LED surface mounted

Batten light of following body material and construction as per IS : 10322 with

driver (Replaceable) as per the requirement with Driver efficiency >85%

,Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -

15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short &

Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80 , Flicker

free (flicker should be below 5 %), life time (LED,Driver & electrical circuitry),

of minimum 50000 Burning Hours with , 70% of initial Lumen

maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6000°K/

6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching)

<3, Maximum power consumption should not more than the specified rating

and Fixture shall be of relevant BIS standard and trade mark certificate (

T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen - -

printing on housing. OEM must have its own in house NABL lab setup for

all testing facilities for LED fixtures. complete in all respect i/c

connections with 1.5 sq mm FRLS, PVC insulated copper conductor

single core cable and earthing etc. as required with Minimum 5 year OEM

warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test

report from NABL lab for all testing required for LED fixtures as per BIS

shall be submitted. Shape size and CCT shall be as approved by Engineerin-

Charge as per requirement. (Thermal management: heat sink of

aluminum housing such that LED junction temperature shall not rise above

DSR Powder coated die cast /Extruded aluminum Body (Thickness ≥ 1.20

LED Panel light 2x2 ft., (System lumen efficacy >135 lm/Watt)

Supplying, installation, Testing & Commissioning of Panel light 2x2 ft., of

following body material and construction as per IS : 10322 with driver as per the

requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt,

freq 50/60 hz, Operating temp range -15 deg to 40 deg

centigrade, internal surge protection of 2.5 KV with Short & Open circuit

protection,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare

Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver

& electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial

Lumen maintained till life ends ,CCT 3000°K / 4000°K / 5700°K

/6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color

DSR Matching) <3, Maximum power consumption should not more than the specified

2025 rating and Fixture shall be of relevant BIS standard and trade mark certificate - -

1.8 (T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/Screen printing

on housing. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC

insulated copper conductor single core cable and earthing etc. as required with

Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output .

LM79 & LM80 Test report from NABL lab for all testing required for LED

fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved

by Engineer-in-Charge as per requirement. (Thermal management: heat sink of

aluminum housing such that LED junction temperature shall not rise above

LED Panel light 1x4 ft., (System lumen efficacy >135 lm/Watt)

Supplying, installation, Testing & Commissioning of Panel light 2x2 ft., of

following body material and construction as per IS : 10322 with driver as per the

requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt,

freq 50/60 hz, Operating temp range -15 deg to 40 deg

centigrade, internal surge protection of 2.5 KV with Short & Open circuit

protection,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare

Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver

& electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial

Lumen maintained till life ends ,CCT 3000°K / 4000°K / 5700°K

/6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color

Matching) <3, Maximum power consumption should not more than the specified

MR rating and Fixture shall be of relevant BIS standard and trade mark certificate - -

(T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/Screen printing

on housing. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC

insulated copper conductor single core cable and earthing etc. as required with

Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output .

LM79 & LM80 Test report from NABL lab for all testing required for LED

fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved

by Engineer-in-Charge as per requirement. (Thermal management: heat sink of

aluminum housing such that LED junction temperature shall not rise above

Digitally signed by ARUN

Supply of Suspended 4ft UGR<19 Linear fixture for Conference hall made with

Extruded Aluminium housing with system lumen of 3800lm & system efficacy of

>=115lm/watt, with continuous mounting using flexible connectors for making

the unique flexible arrangement/patterns of continuous luminaires. The flexible

connector shall be available in single link, bilink, trilink, and quad link to have

multiple possibilities of patterns. The luminaire shall have a rated system lifetime

of 50,000 burning hours at L70B50 with a batwing distribution. The luminaire

should have a color temperature of3000K/ 4000K/6500K and CRI>80/90. The

luminaire shall meet IP20 rating with THD<10% and PF >=0.9, SDCM<3,

working temp. range of -20°C to 40°C, length size of 1200mm, Surge protection

upto 2KV. The fixture design should be with flicker free operations ripple <5%,

comply to IEC61000-3-2 ed.3.2, 2009 for Harmonics, IEC61347 -2 -13, 2006 in

MR Conjunction with IEC61347-1 ed.2.0, 2007 for Electrical Safety, IEC62384 20.00 Each 33,805.00 6,76,100.00

ed.1.1, 2011 for performance and IEC61547 ed.2.0, 2009, EMI/EMC Compliant.

The luminaire driver shall be of the same make/manufacturer of LED.

Manufacturer shall have inhouse lab approved by NABL or ministry of science of

govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL

accredited lab to verify above parameters. Both the fixture and Driver should have

separate BIS approval.

Supply of Deep Recessed low glare LED Downlighter with cut off angle 38°

made up of pressure die cast aluminum housing with high quality glossy facetted

Al reflector and PDC Aluminium external Rim. The luminaire shall have

minimum efficacy at System level approx 120 lumens/watt with system Lumens

750lm & wattage 6W, Life of fixture : 50000 burning Hrs. @ L70B50 Lumen

maintenance, CCT of 3000K/4000K/5700K/6500K,sdcm<=5, CRI Ra >=80, PF

≥0.95, an Operating working temp range 0°C < Ta < 45°C & operating Voltage

MR Range of 140-270 V AC, 50Hz. Minimum Internal Surge Protection 2.5KV, 20.00 Each 2,535.00 50,700.00

THD≤ 10%. Dimensions: 125mm cut out, OD137mm x 85mm. The beam angle

shall be 36deg/60deg.The product shall be with Class B serviceability and shall

be RoHS compliant. Manufacturer shall have inhouse lab approved by NABL or

ministry of science of govt of India. LM 79 and LM80 reports need to be

submitted from a NABL/UL accredited lab to verify above parameters. Both the

fixture and Driver should have separate BIS approval.

Supply of Standalone linear Channel LED suspended luminaire with up-down

distribution, 33% Up and 66% down, with minimum bezel and Sleek propostion

Wide 120mm x 45mm height and 1200mm length with extruded aluminium

housing and high polycarbonate/PS diffuser. LED Used shall be SMD type with

Minimum system Lumens 3300 @28W & efficacy upto 120lm/W,Life of fixture :

50000 burning Hrs. @ L70B50 Lumen maintenance, CCT of 4000K/6500K

(SDCM<=5), CRI Ra ≥80, PF ≥0.95, THD≤10%, an Operating working temp

range : -10°C < Ta < 45°C & operating Voltage Range of 140-270 V AC.

Minimum Internal Surge Protection 4.0KV. The fixture design should be with

flicker free operations ripple <5%, comply to IEC61000-3-2 ed.3.2, 2009 for

MR Harmonics, IEC61347 -2 -13, 2006 in Conjunction with IEC61347-1 ed.2.0, 20.00 Each 5,634.00 1,12,680.00

2007 for Electrical Safety, IEC62384 ed.1.1, 2011 for performance and

IEC61547 ed.2.0, 2009. The luminaire driver shall be of the same

make/manufacturer as that of LED luminaires. The luminaire shall be Class B

Serviceability, Manufacturer shall have inhouse lab approved by NABL or

ministry of science of govt of India. LM 79 and LM80 reports need to be

submitted from a NABL/UL accredited lab to verify above parameters. Both the

fixture and Driver should have separate BIS approval. Dimension should be LBH

Recessed PIR Motion Sensor Similar to Wipro Make : GLPS01R010HA or equivalent

Brush Less Direct Current (BLDC) Motor

Supply, Installation, Testing and Commissioning of ceiling fan with Brush

Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal

(Aluminum alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit,

safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service

Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-

2019), THD (Total Harmonic Distortion) less than 10%, remote (preferably

mobile app based) for speed control and all remaining

accessories including safety pin, nut bolts, washers, temperature rise=75

degree C (max.), insulation resistance more than 2 mega ohm, suitable for

230 V, 50 Hz, single phase AC Ceiling Fan compliant to IS 374:2019 fan

Supply, earthing etc. complete as req

1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min

Supply and fixing hexagonal Round G.P.fan box approved make made up of 1.0

mm thick ISI Marked G.P.sheet spot welded Four to Eight holes for pipe entry

DSR of the box. Holes should be semi-shuttered type with 0.5 mm G.P. Sheet made

Civil upper & lower cover duly screwed. Fixing with wiring conduit laid in the R.C.C.

2023 roof before concreting alongwith supply of all material, labour, T&P etc.

10.18 required for proper completion of the work.

Digitally signed by ARUN

Supply Installation Testing and Commissioning of 400mm sweep 1500RPM

energy efficient BLDC fan with double ball bearing for longer life similar to CGE

RENESA or equivalent.

Lightning Arrestor Work - - -

Lightning Arrestor: Supply, installation, testing and commissioning of External

Lightning wide area protection system based on Eaarly Streamer Emission (ESE)

technology. Device shall emit electromagnetic impulse in the form of a streamer

into the air microseconds earlier than naturally formed streamers. Device confirmg

to NFC 17-102 and UNE 21186 Standards. Appropriate non penetrating

mounting arrangement. The device shall be mounted at suitable clear to the

highest point on the roof top. (Model selected shall give coverage of 79 M radius

@ min 5M height from terrace)

Down conductor:Supply, installation, testing and commissioning of 70 Sqmm

46 MR twisted 19-Strand, bare Cu cable on surface/wall / as per site requirement and 60 Metre 2,510.92 - - 1,50,655.32

complete in all respect.

Lightning Counter :Supply and installation of counting the number of lightning

strikes without any power supply.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm

thick including accessories, and providing masonry enclosure

with cover plate having locking arrangement and watering pipe

of 2.7 metre long etc. with charcoal/ coke and salt as required.

49 MR Test Link :Supply and installation of test link in weather proof IP 65 BOX. 3 Each 2,832.00 - - 8,496.00

Supply, installation, testing and commisioning of 2 x 25W LED Aviation

abstruction light medium bay type 62, complete with lamp, lamp holder,

50 MR Condenser necessary connecting wire, 1 X 25 AV with all necessary hardware, 1 Each 12,279.08 - - 12,279.08

accessories as required for complete installation. Rate shall include the cost of

necessary steel structures , fixing arrangements in this item. Refer drawing.

Online UPS- Input supply: Three Phase, Output supply: Three Phase

Supplying, installation, Testing & Commissioning of of following capacity at full

load (Unity Power Factor) at operating temperature 0 to 40 deg C,

Relative humidity 0 to 95%, Online double conversion true sine wave

Uninterrupted hot swappable (allow for the replacement or addition of

battery modules without shutting down the entire system) modular Power

Supply (UPS) system with N+1 modules (N denotes total number of moduels

requird for rated capacity). The UPS shall include a Rectifier, inverter, battery

bank suitable for 30 minutes back up (Battery VAH capacity shall not be less

than 1600 VAH per KVA of UPS rating per Hour backup time) on full load

51 (Battery shall be VRLA, SMF in ABS Container) and Static Bypass switch - -

alongwith provision for manual bypass, suitable isolation transformer for

additional protection against neutral faults etc. UPS shall have inbuilt

phase sequence correction. The UPS systems offered are to be of the latest

technology with Digital Control Microprocessor based for reliable operation

using Insulated Gate Bipolar Transistor (IGBT)'s both for the rectifier & inverter

(3 Level) with PWM (Pulse Width Modulation). The quality of design,

manufacturing and inspection process should confirm to the relevant International

standards such as IEC/EN/VDE. The operating efficiency of the UPS systems

shall be >96% while operating on battery mode and delivering quality power to - -

the 100% non-linear loads. Current total harmonic effect(ITHD) on the input grid

shall be < 5% at 50 %load. (The required LC (

inductor (L) and a capacitor (C)) filters shall be included in UPS cost),

extreme power factor kit to be included to limit the input power factor (PF) to

0.99 and output power factor shall be unity (i.e. kw rating of the UPS shall be kva

rating x 1 ), however UPS shall be suitable to take load at 0.7 laging to 0.7

leading power factor loads. UPS shall be suitable for incoming supply AC :

3Phase 400V +/-20%, 50 Hz +/-5 Hz, AC Output voltage: 3Phase 415 Volt, 50

Hz +/- 0.2Hz, Overload capacity of 120% for 10 mins, Sine wave output. Non

condensing, noise level less than 60db at 1 meter distance, protections: Input

Under voltage over voltage, abnormal out voltage, battery over charging, output

over current, short circuit protection, battery deep discharge protection, 10KV - -

surge. UPS must comply with low voltage electromagnetic compatibility (EMC)

achieved as per EN 6204, EN6204 Part I and Part 2, it shall be a Voltage and

Frequency Independent (VFI)-type UPS. Communication RS232/RS485/SNMP

port open protocol for BMS

Digitally signed by ARUN

integration, all hardware & software for iOT Communication as per approved by

Engineering in charge. Required battery racks and interconnecting copper

conductor cables of suitable size and connectors and all required accoseries are

inclusive of the cost). This system must provide a means for logging and alarming

of all monitored points plus email notification. Forced air-cooling with integral

inbuilt fans with redundancy (if one fan fail UPS should be able to handle at least

80% of the load, Noise Level 65 DB at 1 meter distance. The system shall be in - -

compliance IEC 62040- 1,2 & 3, IS: 16242 and CPWD Specification. Display

Panel (minimum) (In-build 5 inch or more LC Display / LED ) to display : a)

Input: Voltage, current, Frequency. b) Bypass: Voltage, Frequency. c) Output:

Voltage, frequency, Current.

d) Battery: Voltage, Capacity. e) Load: KVA, KW, Percentage.

f)Temperature: STS, Inverter, PFC. g) Event Logging & Statistical Data (On

LCD/LED): UPS should capture and display up to 3000 events like: Over

temperature / DC Bus Fail / Fan Fail / Fuse Fail / Overload / Short-circuit /

Device Fail / Inverter Fail / Rectifier Fail / Bypass Fail, etc. h) Statistical Data:

No. of power failures / Transfers to Bypass / Total Running time, etc. i) Mains

Mode of Operation /Battery Mode of Operation / Bypass feeding the load /UPS

Fault /Battery charging and discharging, overload, battery voltage and battery

DSR capacity. j) Audible Alarms : Mains Failure, Battery Low Alarm, UPS Overload,

2025 Fault, Shutdown, Input Over, Under Voltage, Output Over, Under Voltage, - -

5.2 Battery Over, Under Voltage, Over Load and short circuit, Over Temperature.

The UPS should have QR code which should contain drawing, test report OEM

manual,Geo- Tag of manufacturing location etc

40KVA (Each Power module shall be < 10 KVA) 5,99,469.00 -

Digitally signed by ARUN

Project - Proposed Composite Regional Centre (CRC) At Jamdoli, Agra Road, Jaipur (Rajasthan).

Name Of Work -CCTV Surveillance System Work

Rate as per D.S.R. 2022

Sr.No. Particulars Sch.No. Qty Unit MR Rate(Rs) AS PER MR Amount(Rs)

SUB HEAD :1 CCTV Surveillance Work - -

Supplying and drawing of UTP 4 pair CAT 6 DSR

1 LAN Cable in the existing surface/ recessed Steel/ 2022 - -

PVC conduit as required. 1.54

Supplying, installing, testing and commissioning

4 of I/O(Information outlet ) for CAT6 Cable MR 41.00 Nos 237.50 9,737.50

Supplying, installing, testing and commissioning

of 6 U wall mount rack with fans , 2 cable

6 managers , satationary shelf , 2 Nos of hardware MR 3.00 Nos 12,462.10 37,386.30

Weatherproof canopy with mounting arrangement

to safely mount Jackpanel and PoE Switch.

Supplying, installing, testing and commissioning

of 42 U wall mount rack with fans , 2 cable

8 managers , satationary shelf , 2 Nos of hardware MR 1.00 Nos 81,384.60 81,384.60

S/I/T/C of 24 port 10/100/1000 Base T

Standalone Gigabit Switch Make Dlink/Amp with

active and passive components, punching,

complete in all respect

Supply, Installation, Testing & Commissioning of

i7 CPU with latest generation windows 10 and

above, 1TB SSD and 500GB RAM.

Supply, Installation, Testing & Commissioning of

CCTV Client Operator Station with 1 No.of 55”

12 LED Display - Complete as per specifications MR 2.00 Nos 92,482.50 1,84,965.00

Supplying, installing, testing and commissioning

13 of HDMI to HDMI Cable. MR 2.00 Nos 1,424.05 2,848.10

Supply Installaon testing and commissioning 6

core OFC cable with splicing etc as required in

14 existing HDPE pipe. MR - Meter 168.15 -

Supply installation testing and commissioning of

15 fully loaded 12 Port LIU. MR - Nos 17,487.60 -

Supply installation testing and commissioning of

16 3m SC-LC Patch cord. MR - Nos 2,073.85 -

Supply installation testing and commissioning of

17 SFP module. MR - Nos 14,535.00 -

Supply installation testing and commissioning of

18 3m Cat-6 patch cord. MR 41.00 Nos 952.85 39,066.85

Digitally signed by ARUN

Supplying and fixing of following sizes of medium

class PVC conduit along with accessories in

surface/recess including cutting the wall and

making good the same in case of recessed conduit

as required. 25mm Dia

Supplying and laying of following size DWC

HDPE pipe ISI marked along with all accessories

like socket, bend, couplers etc. conforming to IS

21 14930, Part II complete with fitting and cutting, 14.15.1 100.00 Meter 127.00 - 12,700.00 -

jointing etc. in the existing trench, complete as

63 mm dia (OD-63 mm & ID-51 mm nominal)

SITC of 5MP Outdoor Dome camera with

1/2.9‑inch CMOS, Effective pixels 3072 (H) x

1944 (V), 30fps, Sensitivity – (3100K, reflectivity

89%, 1/25, F1.3, 30IRE) Color 0.24 lx Mono 0.03

lx With IR 0.0 lx, 120 dB Dynamic range,

Electronic Day/Night, Automatic Electronic

Shutter (AES), H.265, H.264 MP (Main Profile);

M-JPEG Video compression, White balance,

Backlight Compensation, Privacy Mask,Rule

based alarms and tracking, Line crossing, Enter

/leave field, Follow route, Loitering, Idle /

22 removed object, People counting, Crowd density MR 37.00 47,642.50 17,62,772.50

estimation, 3D tracking based on Duration, Size,

Aspect ratio v/h, Speed, Direction, Color, Object

classes (Upright persons, Bikes, Cars, Trucks),

Audio detection (if microphone used), 4 to 10 mm

Automatic Varifocal (AVF) lens, MicroSD card

slot for edge recording, Motion, tamper and audio

detection, FTP, IR range upto 30mtrs Dropbox

and e-mail applications, 3 axis adjustment,

ONVIF Profile S & G & T, PoE, IP66 and

NEMA 4X, IK10, CE, FCC , UL certified. SD

card support up to 2TB.

SITC of 5MP IR Bullet camera with 1/2.9‑inch

CMOS, Total sensor pixels 2592 (H) x 1944 (V);

30 fps; Sensitivity – Measured according to IEC

62676 Part 5 (1/30, F1.6), Color 0.14 lx, Mono

0.032 lx, With IR 0.0 lx, 120dB WDR, H.265;

H.264; M- JPEG, Automatic Electronic Shutter

(AES); Intelligent Dynamic Noise Reduction,

Intelligent Defog,Rule based alarms and tracking,

Line crossing, Enter / leave field, Follow route,

Loitering, Idle / removed object, People counting,

23 Crowd density estimation, 3D tracking based on MR 4.00 41,325.00 1,65,300.00

Duration, Size, Aspect ratio v/h, Speed, Direction,

Color, Object classes (Upright persons, Bikes,

Cars, Trucks), Privacy Masking, Pixel counter,

Memory card slot, IR Range 30mtr, Automatic

Varifocal 3.2 to 10 mm, Alarm Input 1/1, Audio

Input/output, RJ45, G.711, Audio Streaming Full-

duplex / half duplex, ONVIF Profile S, G & T,

IP66, IK10, PoE, CE, FCC, UL certified. SD card

support up to 2TB. FTP, Dropbox and e-mail

SITC of 64 channel Network Video StoragE

NVR suitabe to access data from any remote

location including backup drive for 30days.

Digitally signed by ARUN

Detailed Estimate Based On DSR-2022 With Cost Index & Market Rate

Project - Proposed Composite Regional Centre (CRC) At Jamdoli, Agra Road, Jaipur (Rajasthan).

Name Of Work -Access Control System Work

Rate as per D.S.R. PAR 2023 MARKET BASED

Sr.No. Particulars Sch. No. Qty Unit per Amount(In Rs) Rate(Rs) Amount(Rs)

Supply, Installation, Testing and

Commissioning of 2 Reader Intelligent IP based

Controller with 32 bit processor, 10,000 card

holders, 1,00,000 transaction Logs Enclosure,

Power supply and with all accessories to finish

Supply, Installation, Testing and

2 Commissioning push botton door open switch MR 26 Each 12036.00 3,12,936.00

for single and double door.

Supply, Installation, Testing and

Commissioning IP based

3 Fingerprint Biometric Reader with built in MR 26 Each 33630.00 8,74,380.00

Smart card Reader, Power supply with wiegand

output fully networkable.

Supply, Installation, Testing and

5 Commissioning Single door Magnetic Lock with MR 13 Each 10148.00 1,31,924.00

Door Position Switch.

Supply, Installation, Testing and

6 Commissioning Double Door Magnetic Lock MR 13 Each 17405.00 2,26,265.00

with Door Position Switch

Supply, Installation, Testing and Commissiong

7 of Time Attendance software (PC based for MR 1 Each 88069.30 88,069.30

interfacing and programming) and with require

all accessories to finish the job

Supply, Installation, Testing and Commissiong

8 of Access Control Software (PC based for MR 1 Each 104081.90 1,04,081.90

interfacing and programming) and with require

all accessories to finish the job

SITC of PC Hardware with a minimum

speicification of Intel i7 Quad Core Processor

7th Generation at mim 3.6 GHz , Intel HD

Graphic, 8 GB or more of RAM, 500GB SATA

Hard Drive for OS and ACS & TA applications,

Network Interface Card - 10/100/1000 MB,

Dual Monitor Graphics card to support 2

multiplexed Monitors. DVD-R/W Microsoft®

Windows® 8.1 / 10 Pro or Higher 64 bit

Supply & Laying of 8core 1.0 sq. mm ATC PVC

10 insulated & sheated, twisted pair, Al shielded MR 1820 Meter 247.80 4,50,996.00

and overall FR PVC sheathed cable in in

existing 25 mm PVC/Steel Conduit.

Digitally signed by ARUN

Supply & Laying of 4core 1.5 sq. mm ATC PVC

11 insulated & sheated, twisted pair, shielded and MR 1820 Meter 141.60 2,57,712.00

overall FR PVC sheathed cable in existing 25

mm PVC/Steel Conduit.

Supplying and fixing of following sizes of steel

12 conduit along with accessories in surface/recess -

including painting in case of surface conduit, or

cutting the wall and making good the same in

case of recessed conduit as required.

Digitally signed by ARUN

Detailed Estimate Based On DSR-2022 With Cost Index & Market Rate

Project - Proposed Composite Regional Centre (CRC) At Jamdoli, Agra Road, Jaipur (Rajasthan).

Name Of Work - Lift Work

Rate derived as per PAR 2025 MARKET BASED

Sr.No. Particulars Sch.No. Qty Unit Amount(In Rs) Rate Amount(In Lac)

Supply Installation Testing and Commissioning of lift with power operated doors and AC

variable voltage and variable frequency controls having speed of minimum 1.5m/sec as per

1 CPWD specifications. 13 Passenger elevator with 3 stops 4.1

without machine room as per

13 Passenger (G+5)

Digitally signed by ARUN

Detailed Estimate Based On DSR-2022 With Cost Index & Market Rate

Project - Proposed Composite Regional Centre (CRC) At Jamdoli, Agra Road, Jaipur (Rajasthan).

Name Of Work -EPABX System Work

Rate as per D.S.R. 2022 MARKET BASED

Sr.No. Particulars Sch.No. Qty Unit Amount(In RS) Rate(Rs) Amount(In RS)

A EPABX SYSTEM

SITC of IP-PBX WITH REDUNDANT

CPU & REDUNDANT POWER SUPPLY

4 CO TRUNK, 50 ANALOG

EXTENSION, 10 SIP TRUNK, 4 E1 PRI

TRUNK, 10 IP EXTENSION, PMS

SITC of REDUNDANT FCBC WITH 12V

BATTERIES WITH 15AH CAPACITY

3 SITC OF IP PHONE WITH DISPLAY MR 10.00 Nos - 6,608.00 66,080.00

4 SITC OF BASIC PHONE WITH CLI MR 9.00 Nos - 1,888.00 16,992.00

S/f of I/O Boxes Krone connectors ,with

connection etc.

Wiring of Jelly Filled telephone Cable in

existing pipe for system with connection.

Supplying, installing, testing and

commissioning of 24 port CAT6 jack panel

loaded as per the connections required in

Supplying, installing, testing and

commissioning of 6 U wall mount rack

with fans , 2 cable managers , satationary

shelf , 2 Nos of hardware pkts.

Supplying, installing, testing and

9 commissioning of 24 10/100/1000BASE-T MR 1.00 Nos - 93,703.00 93,703.00

Supplying, installing, testing and

commissioning of 42 U wall mount rack

with fans , 2 cable managers , satationary

shelf , 2 Nos of hardware pkts.

Digitally signed by ARUN

SITC of 2m long Cat-6 patch cord as

Supplying and laying of following size

DWC HDPE pipe ISI marked along with

all accessories like socket, bend, couplers

conforming to IS 14930, Part II complete

with fitting and cutting,

jointing etc. in the existing trench,

complete as required. 100mm Dia

Digitally signed by ARUN

Detailed Estimate Based On DSR-2022 With Cost Index & Market Rate

Project - Proposed Composite Regional Centre (CRC) At Jamdoli, Agra Road, Jaipur (Rajasthan).

Name Of Work -Networking System Work

Rate as per D.S.R. 2022 MARKET BASED

Rate as Amount(In Amount(In

Sr.No. Particulars Sch.No. Qty Unit Rate

per DSR RS) RS)

A DATA / NETWORKING SYSTEM

S/F of Surface mount box with I/O Cat

1 6 and UTP jack D-Link complete in all MR 85.00 Nos - 548.70 46,639.50

2 S/I of Patch cord CAT6 UTP MR 85.00 Nos - 265.50 22,567.50

S/I/T/C of 24 port category 6e SL

Series patch Panel with active and

passive components,punching,

complete in all respect

S/I/T/C of 48 port category 6e SL

Series patch Panel with active and

passive components,punching,

complete in all respect

S/I/T/C of 24 port 10/100/1000 Base T

Standalone Gigabit Switch with active

and passive components, punching,

complete in all respect

S/I/T/C of 24 port 10/100/1000 Base T

Standalone Gigabit L2 Switch with

active and passive components,

punching, complete in all respect

Supplying, installing, testing and

commissioning of 6 U wall mount rack

7 with fans , 2 cable managers , MR 3.00 Nos - 13,118.00 39,354.00

satationary shelf , 2 Nos of hardware

Mapping of Network Nodes & LAN

SITC of WIFI Modem suitable to cover

atleast 25m distance having

9 compatibility to connect atleast 40-50 MR 37.00 Job - 77,408.00 28,64,096.00

devices without any distortion in signal

etc as required.

Digitally signed by ARUN

Detailed Estimate Based On DSR-2022 With Cost Index & Market Rate

Project - Proposed Composite Regional Centre (CRC) At Jamdoli, Agra Road, Jaipur (Rajasthan).

Name Of Work - Fire Fighting System Work

Rate as per D.S.R. 2022 MARKET BASED

Sr.No. Particulars Sch.No. Qty Unit DSR Rate(Rs) Amount (In Rs)

Sub Head : A (Pump Room)

Supplying, installation, testing and commissioning of Electric driven

Main Fire Pump suitable for automatic operation and consisting of

following, complete in all respects, as required :Horizontal type,

multistage, centrifugal, split casing pump of cast iron body & bronze

impeller with stainlesssteel shaft, mechanical seal conforming to IS

1520. Suitable HP Squirrel cage induction motor, TEFC,

synchronous speed 1500 RPM, suitable for operation on 415 volts, 3

phase 50 Hz, AC supply with IP 55 protection for enclosure,

horizontal foot mounted type with Class- 'F' insulation, conforming

to IS-325. supply , Installation, testing and commissioning of fire

Hydrant valve , bearing to IS:5290 marks, S.S. ,IS: 304 Grade,

63mm oblique instantaneous single out let, 75mm N.B. flanged inlet,

brass spindles complete with PVC blank cap . G.I. chain etc.

guard,foundation bolts etc.as required. supply , Installation, testing

and commissioning of Branch pipe . S.S. short type with 63mm male

instantaneous inlet, male threaded outlet fitted with 15mm, Bore

nozzle,having IS: 903 with anti vibration pads.

Supplying, installation, testing and commissioning of diesel engine

driven main fire pump suitable for automatic operation and

consisting of following,

complete in all respects, as required : (Diesel Driven Pump)

Horizontal type, multistage, centrifugal pump of cast of iron body

and bronze impeller with stainless steel shaft, mechanical seal

conforming to IS 1520. Suitable HP, 1500 RPM water cooled with

radiator, diesel engine conforming to relevant IS standard complete

with auto starting mechanism, 12 /24 volts electric starting

equipment, diesel tank, exhaust pipe extended upto 10 m outside

pump house duly insulated with 50 mm thick glass wool with 1.0 -

aluminium sheet cladding, residential silencer, instruments and

protection as per standard specification, stop solenoid for auto stop

in the event of fault with audio indications, painted with post office

red colour etc. as required.

M.S fabricated, common base plate, coupling, coupling guard,

foundation bolts etc. as required. Suitable cement concrete

foundation duly plastered

and with anti vibration pads.

Supplying, installation, testing and commissioning of electric driven

pressurisation pump suitable for automatic operation and consisting

of following, complete in all respects, as required : (Jockey Pump)

Horizontal type, multistage, centrifugal pump of cast iron body and

bronze impeller with stainless steel shaft, mechanical seal

conforming to IS : 1520. Suitable HP squirell cage induction motor

TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC -

supply with IP 55 class of protection for enclosure, horizontal foot

3 mounted type with Class-'F' insulation, conforming to IS : 325.

M.S.fabricated Common M.S.fabricated Common base plate,

coupling, coupling guard, foundation bolts etc. as required. Suitable

cement concrete foundation duly plasteredand with anti vibration

Digitally signed by ARUN

Fabrication, supply, Insallation testing & commissioning of

Electrical control panel of cubical construction, floor mounted type,

fabricated out of 2mm thick CRCA sheet, compartmentalised with

hinged lockable doors, dust and vermin proof, powder coated of

approved shade after 7 tank treatment process, cable alley,

interconnection with suitable size copper conductor cable/solid

4 copper strip, having switchgears and accessories, mountings and -

internal wiring, earth terminals, numbering etc. complete in all

respect, suitable for main fire pump, pressurisation pump & diesel

pump set complete as per CPWD specification with following in

coming and Outgoings, suitable for operation on 415V, 3 phase,

50Hz Ac Supply with.

400A, 50kA 4 Pole MCCB, Ics=100% Icu rating Digital Voltmeter 0-

500V with selector switch Ammeter (0-400 A) with selector swtich

& CTs etc. LED type RYB phase indicating lamps, ON, OFF, trip -

indicating lamps Set of Copper Bus Bar 500A

( Note : All outgoing feeders for pumps should have digital

Ammeter with selector switches, and LED type ON, OFF, trip -

indicating lamps)

Main Fire Pump -

160 A, 50kA TPN MCCB, Ics=100% Icu, with fully automatic

Star/Delta starter suitable for 75 hp pump with overload protection,

current sensing type single phase preventor complete with all

acceessories and internal wiring required for automatic operation, -

selector switch for local/remote, auto/manual/OFF operation.

100 A, 50kA TPN MCCB, Ics=100% Icu, with suitable HP fully

automatic Star/Delta starter with overload protection, current

sensing type single phase preventor complete with all acceessories -

and internal wiring required for automatic operation, selector switch

for local/remote, auto/manual/OFF operation.

Diesel Engine Control -

Control for diesel engine comprising - -

Automatic/Manual selctor switch & 3 attempt starting device, timers

and relays as required, push buttons, start/stop in manual mode

Indicating lamp for high/ Low Lub. Oil pressure, High Water Temp

and Engine on indication Battery charger suitbale for 12V/24 V DC

with boost and trickle selector switch, 0-30 V DC volt meter, and 0-

20 A DC Ammeter All standard relays and accessories for automatic

operation of diesel engine System Controller Designing, Supply, 18.5.2 1.00 set 2,87,855.00 2,87,855.00 -

Installation, Testing and commissioning of system controller to

control operation of main electric fire pump, diesel pump,

Pressurization pump, Terrace pump in sequence as per specification

consisting of relays, timers. Sensors, annunciation window for fault

indication, complete as per specifications.

Supply, erection and testing of ISI marked M.S. pipes (class C) and

specials etc. (as per IS:1239) for above ground laying for hydrants

system includeing transportation of materials upto the worksite,

cuttings the pipes to required length, edge preparation, welding,

5 fixing / erection of pipes including specials i.e. bends, tees, reducers, 18.7 -

flanges expansion joints wherever required, washers, nuts, bolts etc.

in proper position including all supports as per layout.

200 mm dia (wall Thickness 6.3 mm)

Digitally signed by ARUN

Providing, installation, testing and commissioning of non-return

valve of following sizes confirming to IS: non-return valve of

6 following sizes confirming to IS: 5312 complete with rubber gasket, - -

GI bolts, nuts, 5312 complete with rubber gasket, GI bolts, nuts,

washers etc.as required washers etc.as required :

Providing, installation, testing and commissioning of stainless steel

7 Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, 18.15.4 - -

sheet with 3 mm dia holes with stainless steel flange.

Installing ,testing and commissioning of butterfly valve , PN-

8 1.0,slim seal,standard lever operated type with required flanges, nuts 18.11 - -

,bolts etc. complete.

Providing and fixining pressure gauge.

Providing and fixining 25 mm dia Ball Valve.

Providing and fixining air release valve.

Supplying & fixing air vessel made out of 250 mm dia,8 mm thick

MS sheet, 1200 mm in height with air release valve on top and

12 flanged connection to riser, drain arrangement with 25 mm dia gun 18.20 1.00 each 18,244.00 18,244.00 -

metal wheel valve with required accessories, pressure gauge and

painting with synthetic enamel paint of approved shade as required.

Supply, installation, testing & commissioning of flow switches with

two no and two NC contacts with necessary nipply & other fittings,

Flow switch shall be suitable for 150 dia.

Providing, fixing, testing & commissioning of installation control

valve of cast iron body, brass/bronze working parts comprising of

water motor alarm, bronze seat clapper, clapper arm and

hydraulically driven mechanical gong bell to sound continuous alarm

14 when the wet riser/sprinkler system activates, pressure gauges, 18.24.3 1.00 Each 48,202.00 48,202.00 -

emergency releases, strainer, pressure switch, cock valve complete

with drain valve and bypass, test control box, ball valves, MS pipe of

required size, flanges, orifice plate, gasket etc of follwing sizes as

Sub Head : B (External Hydrant)

Providing laying, testing & commissioning of 'C' class heavy duty

MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees,

flanges, tapers, nuts bolts, gaskets etc. in ground including welding,

1 excavation & providing cement concrete blocks as supports, 18.6 - -

anticorrosive treatment with coaltar/asphalt tape as per IS 10221,

refilling the trench etc. of following sizes complete as required.

Digitally signed by ARUN

Supplying, Installing, hydraulic testing and commissioning of heavy

grade MS Pipe confirming to IS:1239 part-1 with malleable specials

confirming to IS:1239 part-II, such as Tee, elbows, check nuts,

unions, flanges, nipple etc. Including cutting, fixing in/on wall/ on

Floors, ceiling by using usitable supports such as MS channels,

2 angles, flats, rods as required at site with anchor fastners, clamps, 18.7 - -

threaded rods, nuts, bolts, washers etc.. complete. Painting the

exposed with one coadt of metal zinc chromate primer with two

coats of synthetic enamal paint of approved colour/shade etc.

Supplying and fixing Single headed external yard hydrant valve with

1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel

coupling and cast iron wheel, ISI marked, conforming to IS 5290

(type A) with blank Gunmetal/Stainless Steel cap and chain as

Supplying and fixing orifice plate made out of 6 mm thick stainless

steel (Grade 304) with orifice of required size to be fitted between

4 flange & landing valve of 18.13 13.00 each 1,321.00 17,173.00 -

external and internal hydrants to reduce pressure at the outlet to the

level of 3.5 kg/cm2 complete as required.

Hose cabinet stand mounted type fabricated out of M.S. sheet of 16

swg. With glass fronted (4mm thick glass with rubber beading) door

and size of the cabinet shall be 600x750x250mm Quoted rate shall

5 be inlcludes suitable stand for mounting for ground level with MR 13.00 each - 7,670.00 99,710.00

sup[orts all fastners etc, and cabinet shall be painted/powder coated

of approved colour both inside and out side.

supply , Installation, testing and commissioning of Branch pipe . S.S.

6 short type with 63mm male instantaneous inlet, male threaded outlet 18.18.2 13.00 EACH 1,662.00 21,606.00 -

fitted with 15mm, Bore nozzle,having IS: 903.

supply , Installation, testing and commissioning of Fire Hose,RRL

hose jacketed with circular woven synthetic fibre,conforming to IS

636:88 63MM DIA.x 15mt. Long with SS 63mm 2 pair of male and

7 female instantaneous coupling having IS :903 mark and duly S.S. 18.16.1 26.00 EACH 5,202.00 1,35,252.00 -

wire wounded. The hose shall be rolled and hug to suitable M.S.

support in the fire station.

Sub Head : C (Internal Hydrant)

Supply, erection and testing of ISI marked M.S. pipes (class C) and

specials etc. (as per IS:1239) for above ground laying for hydrants

system includeing transportation of materials upto the worksite,

cuttings the pipes to required length, edge preparation, welding,

1 fixing / erection of pipes including specials i.e. bends, tees, reducers, 18.7 - -

flanges expansion joints wherever required, washers, nuts, bolts etc.

in proper position including all supports as per layout.

Supply , Installation, testing and commissioning of Fire Hydrant

valve , bearing to IS:5290 marks, S.S. ,IS: 304 Grade, 63mm

2 oblique instantaneous single out let, 75mm N.B. flanged inlet, brass 18.9.1 6.00 EACH 7,646.00 45,876.00 -

spindles complete with PVC blank cap . G.I. chain etc.

Digitally signed by ARUN

supply , Installation, testing and commissioning of Branch pipe . S.S.

short type with 63mm male instantaneous inlet, male threaded outlet

fitted with 15mm, Bore nozzle,having IS: 903

supply , Installation, testing and commissioning of Fire Hose,RRL

hose jacketed with circular woven synthetic fibre,conforming to IS

636:88 63MM DIA.x 15mt. Long with SS 63mm 2 pair of male and

4 female instantaneous coupling having IS :903 mark and duly S.S. 18.16.1 12.00 EACH 5,202.00 62,424.00 -

wire wounded. The hose shall be rolled and hug to suitable M.S.

support in the fire station.

supply , Installation, testing and commissioning of manual swing

type Fire hose reel IS:884 comp. with heavy duty reel, 19mm dia. X

30 mtr. Long 2- ply polyster yarn braided / rubber braided pressure

hose with heavy duty nylon on/off jet/ spray nozzle, 25mm isolating

valve and all other necessory.

Supply and fixing of Fire Shaft door fabricated out of G.I. Sheet and

frame, door shall be 900mm x 1500mm min with double leaf. &

fixed with 4 mm thick Glass, suitable Rubber beeding and Locking

6 arrangment. Quoted rate shall be included alll fasterners etc, and MR 6.00 EACH - 5,900.00 35,400.00

complete shutter shall be powder coated of approved colour both

inside and out side.

7 Providing/Fixing Fire man axe. Make. MR 6.00 Each - 472.00 2,832.00

CO2 type Fire exitinguisher ISI marked confirming to IS:15683

lates. Capacity 4.5 kg complete with delivery hose horn, squeeze

grip release valve, locking arrangement, operating temperature -30°c

to +55°c, supplied with body bearing IS 7285 mark and approved

8 valve as per IS 3224. Co2 Gas as per IS:15222. externally painted - -

with PO Red Shade No. 538 of IS 5, operation manual and floor

stand or wall mount Bracket including accessories as required as per

site condition.

Powder Fire exitinguisher (stored Pressure Type) (Powder

pressurized with dry nitrogen gas at 15 bar) capacity 4kg duly ISI

marked conforming to IS:15683:2006/latest, with IS 14609 ISI

marked ABC powder complete with squeeze grip release valve,

9 discharge pipe, locking arrangment, pressure gauge, operation - -

maual, Body Hydrotested at 35 bar, operating temperature--30°c to

+55°c, external epoxy powder coating with PO Red shade No. 538

of IS 5, and floor stand or wall mount Bracket including accessories

as required as per site condition.

Sub Head : D (SPRINKLER SYSTEM )

Supplying, Installing, hydraulic testing and commissioning of heavy

grade MS Pipe confirming to IS:1239 part-1 with malleable specials

confirming to IS:1239 part-II, such as Tee, elbows, check nuts,

unions, flanges, nipple etc. Including cutting, fixing in/on wall/ on

Floors, ceiling by using usitable supports such as MS channels,

1 angles, flats, rods as required at site with anchor fastners, clamps, 18.7 - -

threaded rods, nuts, bolts, washers etc.. complete. Painting the

exposed with one coadt of metal zinc chromate primer with two

coats of synthetic enamal paint of approved colour/shade etc.

Digitally signed by ARUN

Supply testing and commissioning of 15mm gunmetal/chrome

quartzoid bulb, standard reponse sprinkler heads suitable for 65 deg.

Horizontal side wall sprinkler 18.21.3 4.00 Each 617.00 2,468.00 -

Dial Type pressure guage for (0-16 kg/cm2) with necessary nipple &

3 other fittings, mounting arrangements and with 15 mm ball valve. MR 6.00 Each - 3,009.00 18,054.00

Supply, Installtion, Testing & commissioning of 25mm ball valve

4 with sight glass for sprinkler test line. MR 6.00 Each - 1,770.00 10,620.00

Supply, Installation, testing & commissioning of 50mm ball valve

5 for sprinler drain line. MR 6.00 Each - 2,714.00 16,284.00

Supply, installation, testing & commissioning of flow switches with

two no and two NC contacts with necessary nipply & other fittings,

Flow switch shall be suitable for 100 dia.

Installing ,testing and commissioning of butterfly valve , PN-

1.0,slim seal,standard lever operated type with required flanges, nuts

,bolts etc. complete.

Supply & Fixing of approved type rosette plates (Recessed Type, in

two piece) for sprinklers below false ceiling area. Rosette shall be

S.S. 304 as approved by engineers/ services consultants.

Stainless steel corrugatd flexible pipe(hose) for dropping sprinklers

below false ceiling, pipe shall be UL Listed, 16 bar pressure rating

9 and 25 mm dia with union/reducers collor, clamps etc. as 18.25 - -

required.(Braided)

Supply, Installtion, testing and commissioning of 25 mm diameter

10 Forged Brass air release valve PN-1.6 Body. MR 2.00 Each - 1,475.00 2,950.00

Supply, Installation and commissioning of Annunciator Panel with 7

11 windows with point, zone & system status used with RS 485. MR 1.00 Each - 89,208.00 89,208.00

12 Supply, Installation wire for annunciator panel. - -

Digitally signed by ARUN

Detailed Estimate Based On DSR-2022 With Cost Index & Market Rate

Project - Proposed Composite Regional Centre (CRC) At Jamdoli, Agra Road, Jaipur (Rajasthan).

Name Of Work -Fire Detection Alarm & PA System Work

Rate as per D.S.R. 2022 MARKET BASED

Rate as per Amount (In Amount (In

Sr.No. Particulars Sch.No. Qty Unit Rate

DSR Lac) Lac)

Fire Alarm System :

Supplying, installation, testing and commissioning of

micro processor based intelligent addressable main fire

alarm panel, central processing unit with the following

loop modules and capable of supporting not less than 240

devices (including detectors) and minimum 120 detectors

per loop and loop length up to 2 km, network

communication card, minimum 320 character graphics/

LCD display with touch screen or other keypad and

minimum 4000 events history log in the non volatile

1 memory (EPROM), power supply unit (230 ± 5% V, 50 17.2.1

hz), 48 hrs back-up with 24 volt sealed maintenance free

batteries with automatic charger. The panel shall have

facility to connect printer to printout log and facility to

have seamless integration with analog/digital voice

evacuation system (which is part of the schedule of work

under SH: PA System) and shall be complete with all

accessories . The panel shall be compatible for IBMS

system with open protocol BACnet/ Modbus over IP

complete as per specifications.

Supplying, installation, testing & commissioning of

central graphical fire alarm management system to

centrally monitor and operate the fire alarm system

complete as required.

Supplying, installation, testing & commissioning of

repeater panel wih 320 character/ Touch screen LCD

display with inbuilt reset, acknowledge and silence

switches complete as required.

Supplying, installation, testing & commissioning of

intelligent analog addressable photothermal (Smoke)

detector complete with mounting base complete as

Supplying, installation, testing & commissioning of

response indicator on surface/recessed MS Box having

two LED, metallic cover complete with all connections

etc as required.

Supplying, installation, testing & commissioning of fault

isolator complete with base as required.

Supplying, installation, testing & commissioning of

intelligent addressable thermal detector with rate of rise

cum fixed tempreature thermistor complete with base as

Supplying, installation, testing & commissioning of

addressable fire control module complete as required.

Digitally signed by ARUN

Supplying, installation, testing & commissioning of

addressable phone control module complete as required.

Supplying, installation, testing & commissioning of

addressable beam detector with short circuit isolator

or seperate) complete with emitter and receiver including

connections with remote test features etc complete as

Supplying, installation, testing & commissioning of

addressable manual call point complete as required.

Supplying, installation, testing & commissioning of

addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning of fire

fighter telephone handset complete as required.

Supplying, installation, testing & commissioning of fire

fighter phone jack complete as required.

Supplying & laying of 2x1.5 sqmm fire survival

armoured cable, 600/1000V rated with annealed copper

conductor having glass mica fire barrier tape covered by

15 an extruded layer of Cross Linkable Ethylene Propylene 17.5.1 1850 metre 359.00 6,64,150.00 -

Rubber (EPR) insulation and LSZH inner bedding, steel

wire armouring & LSZH outer sheath complete as

Public Addressable System : - -

Supplying, installation, testing & commissioning of 6

zone, voice alarm controller with USB, MP3 player

16 (including 6 zone button paging station) with seamless 17.3.1 1 each 1,26,411.00 1,26,411.00 -

integration facility with main fire alarm panel for voice

evacuation complete as required.

Supplying, installation, testing & commissioning of

1.5/3/6W ceiling speaker complete as required.

Supplying, installation, testing & commissioning of

18 1.5/3/6W metal box ceiling/wall speakers complete as 17.3.3 6 NOS 1,793.00 10,758.00 -

Supplying, installation, testing & commissioning of

19 digital audio amplifier 500 Watt, 25V rms operating at MR 1 each - 2,78,008.00 2,78,008.00

240 Volt AC Supply complete as required.

Supplying, installation, testing & commissioning of

20 Voice command keypad 6 zone, with microphone 17.3.9 1 each 81,756.00 81,756.00 -

assembly complete as required.

Digitally signed by ARUN

Supplying and drawing of cable Fire Retardant PVC

insulated copper conductor cable in the existing surface /

21 recessed steel conduit of following pairs, cores and size 17.5.3 - -

connections and interconnections etc. as required.

17.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm 17.5.3.1 1640 metre 54.00 88,560.00 -

Same as in item 148, but 25mm dia PVC conduit.

Digitally signed by ARUN

NAME OF WORK -PROPOSED CONTRACTION OF COMPOSITE REGIONAL CENTRE (CRC) AT JAMDOLI, AGRA ROAD , JAIPUR (RAJASTHAN)

PROJECT : COMPOSITE REGIONAL CENTRE (CRC) AT JAMDOLI, AGRA ROAD , JAIPUR (RAJASTHAN)

DSR 2025 AS PER MARKET RATE

DSR - RATE AMOUNT

Sr.No. Description Qty Unit QTY AMOUNT RATE (RS.)

VRV/VRF Out Door units :

Supply, Installation, Testing & Commissioning of Modular type Variable

Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units

suitable for cooling/heating having 100% hermetically sealed inverter type twin Rotary/Scroll Compressor(s),

minimum two compressors (with individual seperate PCB) for above 14HP modules, icroprocessor based

Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or equivalent, vibration Isolators

with suitable foundation etc. complete as required. To have better efficiency condensor fan shall be capable to

operate at different speed with respect to load. The unit shall deliver the rated capacity and in confirmation as

per IS 18728:2024 and CPWD Specifications and work even at 50°C ambient temperature without tripping.

The system shall be able to deliver 100% of the rated capacity upto 39 Degree Celcius. The unit shall be

suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall be

filled with first charge of the refrigerant and ready for use as required. The condenser should be coated with a

hydrophilic film to prevent water accumulation on the surface of the heat exchanger, enhance water dispersion,

and reduce the risk of degradation, thereby improving overall performance and durability. The Indian Seasonal

Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation and Sustainable Building

Code (ECSBC) 2024 as below and complete as per CPWD specification, connections, inter connections etc. as

required. (For capacity <40 kWr ISEER 6.4, Capacity >40 and <70 ISEER 6.5, Capacity > 70 ISEER 6.6 for

ECSBC+ Building) For Cooling or Heating or Both

Supply, Installation, Testing and Commissioning of following minimum

capacity 4 way Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter,

fan section with low noise fan /dynamically balanced blower, multispeed motor, coil section with DX Copper

coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration Isolation,

Corded remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete,

as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The

system shall be capable to adjust air flow as per room requirement in auto mode. The cooling capacity of

indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature

Wall Monuted Type units:

Supply, Installation, Testing and Commissioning of following minimum

capacity High wall type Indoor unit equipped with and comfort washable

synthetic media pre-filter, fan section with low noise fan/dynamically

balanced blower, multispeed motor, coil section with DX copper coil,

electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc.,

suitable for operation on 230 V ± 10%, 50Hz, single phase AC supply, complete as required. The Indoor units

must shut down upon receiving a singal from the BMS System/Fire Singnals. The system shall be capable to

adjust air flow as per room requirement automatically. The cooling capacity of indoor unit will be at air inlet

conditions of 27 Degree C DB and 19 Degree C WB temperature.

Supply, Installation, Testing and Commissioning of Y/T/Multi Joints. Joints shall be of same Original Nos.

4 7.13 Equipment Manufacturer (OEM) make as of ODUs and IDUs

4.2 7.13.2 Outdoor Units Multi Joint Nos. Nos. 8 8,098.00 64,784.00

Supply,Installation,testing and commissioning of corded Cord type remote control with thermostat, LED

5 MR Display and internal wiring for Cassette & hi-wall . Nos. 63 3,038.50 1,91,425.50

6 7.14 COPPER REFRIGERANT PIPING

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following

nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with

suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE

Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of

specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as

6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm

6.3 7.14.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm 700 Rmt 155 487.00 75,485.00

6.4 7.14.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm 500 Rmt 425 615.00 2,61,375.00

6.5 7.14.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm 550 Rmt 80 739.00 59,120.00

6.6 7.14.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm 650 Rmt 95 904.00 85,880.00

6.7 7.14.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm 550 Rmt 110 1,157.00 1,27,270.00

6.8 7.14.10. 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm 190 Rmt 105 1,286.00 1,35,030.00

6.9 7.14.12 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm 550 Rmt 98 1,368.00 1,34,064.00

Digitally signed by ARUN

Supply installation testing commissioning Shielded Control Cables for VRV System with necessary ISI mark

Medium class rigid PVC pipes with necessary accessories with termination in machine and control equipments.

7.1 (A) 2Cx1.5 Sq mm Shielded Armoured(for communication lead & remote ) Rmt 1485 223.26 3,31,535.16

Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be erected as

8 MR directed of following size.

3C x 2.5 sq.mm FOR INDOOR UNIT POWER CABLE

9 MR Drain Piping :

Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm thick.nitrile rubber insulation.

VENTILATION SYSTEM

Supply, installation, testing and commissioning of floor mounted / ceiling hang Axial flow type supply air fan

for Lift well, lobby & stairwell pressurization of following capacity with powder coated GSS/M.S. casing and

aluminium alloy impellers with high efficiency aero-foil sections, blades, the impeller directly driven by TEFC

induction motor (efficiency 1) and 'F' class insulation suitable for 3 Phase, 50 Hz, 415±10% Volt, TP isolator

with M.S enclosure box complete as required and as per specifications. Fans should be statically &

dynamically balanced.The fan static pressure shall be 20 mm WC static. as per site condition

a) 3500 CFM (for Lift)

c) 10000 CFM ( Smoke Exhaust)

Supply, installation, testing & commissioning of ducted Inline Fans constructed of GSS duly powder coated

(rectangualr box type & circular type) with centrifugal blower and motor encased in sheet metal casing, canvas

connection etc.The Fan motor shall have electric motor suitable for operation on 220 V+ 10%,50 Hz, 1 phase

AC supply. The Fan assembly shall conform to specifications & in accordance with requirements of drawings

& Schedule Of Quantities.

Supplying, installation, testing & commissioning of Propeller type exhaust air fans suitable for following

capacities complete with electric motor suitable for operation on 220 V+ 10%,50 Hz, 1 phase AC supply

fitted with speed regulator, mountings, frames, louvers and bird screen etc. of the following capacities.

Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round

ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per

13 approved drawings and specifications of following sheet thickness complete as required.

16.12.2. Thickness 0.63 mm sheet 600

Supplying & fixing of powder coated extruded aluminium Supply Air Grills/fresh Grill with aluminium

volume control dampers complete as per specifications and size & shape as per site requirement and approved

Supplying & fixing of powder coated extruded aluminium Return Air /Exhaust Grills with louvers but

15 16.16 without volume control dampers complete as per specifications and size & shape as per site requirement and Sqm 6 5,181.94 31,091.63

approved design.

Supply,installation,testing and commissioning of flexible duct connections constructed of fire resistance

16 MR flexible double canvas sleeve as per the drawings and specifications. Sqm 20 7,637.55 1,52,751.00

Supply, installation, testing and commissioning of anodised aluminium Fresh air/exhaust air louvers with bird

17 MR screen as per specifications and drawings. Sqm Sqm 2 9,950.94 19,901.88

Fully automatic DOL starter suitable for operating 3.7kw motors/fan capacity, complete with contactors,Timer,

overload protection relay, current sensing type single phase preventer, ON indications, push buttons, auto /

18 MR manual / off selector switch,other accessories. complete as required. Set 6 35,849.58 2,15,097.48

Digitally signed by ARUN

SUMMARY OF RATES-AUDIO VISUAL

S.No. Description of Area Qty Amount Total Amount

S.No. Description of Area Qty Amount Total Amount

1 1st Floor Classrooms 8.00 41,370.80 3,30,966.40

5 2nd Floor Classrooms 4.00 41,370.80 1,65,483.20

Digitally signed by ARUN

S.No Description Qty Unit Rate Amount

1 Supply,Installation,Testing & 1 Nos. 2,950.00 2,950.00

Commissioning of Wall Hardware for the

2 Supply,Installation,Testing & 4 RM 3,115.20 12,460.80

Commissioning of High Speed triple-

shielded bonded pairs HDMI Cable with

Ethernet Gold Palted Lockable

Connector. It support Data Transfer rate of

upto minimum 10GBps and upto 48 bit

Deep Color. Cable has overall shield

against EMI/RFI interference and CL2

flame tested , Length 1.8mtr.

3 Supply,Installation,Testing & 100 RM 141.60 14,160.00

Commissioning of CAT6A U/FTP 4

shielded twisted pairs ,23AWG solid

copper conductor Video & LAN , Bulk

Cable — Low Smoke & Halogen Free

recommended by HDBaseT. .

4 Mis Interface Cables & Connectors 1 Set 11,800.00 11,800.00

Total 41,370.80

Digitally signed by ARUN

MULTIPURPOSE HALL(12000X23770)

S.NO Description Qty Unit Rate Amount

1 Supply of All In One Active LED of 165" Diagonal, No. 1 32,41,703.08 32,41,703.08

overall size 3,674*2,175*31,Pixel pitch 1.9mm ,

Resolution 1920 x 1080 , Aspect Ratio 16:9 , Pixel

Density per sqm - 275,290, Cabinet Material

Magnalium, Screen Protection Coating On

Surface,Brightness(Typical) 800 Nits , Refresh

Rate (Hz) 3840, Contrast ratio 10,000:1 , Inbuilt

Wireless presenter , In built speakers , Inputs 3 x

HDMI , Output 1 x HDMI , Embedded controller ,

Signal processing Upto 4 simultaneous source

display, Controller android, Storage 32 GB ,1 x

RS 232 port , 1 x 485 port , 1 x LAN port complete

with IR Remote control with wall mount hardware.

2 Supply, installation, testing & commissioning of No. 3 150527.88 4,51,583.64

PTZ ,Camera with HD Resolution Real High

Definition Image with 1/2.3 inch or higher high

quality HD CMOS sensor , 1920 x 1080 super

high quality video ,20 x or more zoom with 20x or

more digital zoom, Pan Range: 170deg or more

With HDMI output interface for video & RS 232/

RS 422 for controls 10 or more preset position.

3 Supply , Installation , Testing & Commissioning of No. 1 160480 1,60,480.00

Matrix 4k Switcher Metal Chassis , with 6 nos

Input slots (HDMI/DVI /DisplayPort/HdBaseT ) , 2

nos. output , Resolution 4k (4096x2160 ) ,

Input/Output Signal Types HDMI/DVI

/DisplayPort/HdBaseT,Advanced EDID

management,HDCP complaint , Audio output ,

Ethernet port 10/100 Mbps.

4 Supply , Installation , Testing & Commissioning No. 4 53100 2,12,400.00

Twisted pair transmitter convert HDMI to Cat6 signal

( Upto 70 meter ), Resolution upto WUXGA ,

HDCP2.2 complaint , compatability with CEC and

EDID signals , Audio compatability , audio formats

including Dolby TrueHD, Dolby Digital Plus, and DTS-

HD Master Audio transmission.

Digitally signed by ARUN

5 Supply , Installation , Testing & Commissioning No. 4 78068.8 3,12,275.20

Twisted pair receiver convert Cat6 signal to HDMI ,

Resolution WUXGA HDCP2.2 complaint ,

compatability with CEC and EDID signals , Audio

compatability , audio formats including Dolby

TrueHD, Dolby Digital Plus, and DTS-HD Master

Audio transmission.

6 Supply , Installation , Testing & Commissioning of No. 16 9385.72 1,50,171.52

Ceiling Speakers with 30 Watts Continuous Power

Handling, requency Range (-10 dB): 80 Hz - 20 kHz ,

Frequency Response (+/- 3 dB): 100 Hz - 18 kHz ,

Power Capacity1: 150 W , Sensitivity2: 87 dB SPL, 1

W 1 m (3.3 ft) , Maximum SPL3: 108 dB continuous,

Supply , Installation , Testing & Commissioning of No. 2 69502 1,39,004.00

Dual Channel Amplifier with utput 240W @ 4/8 Ohms

(1kHz Power, THD+N<0.5%) , Frequency Response

+/- 1dB (@1W into 4 or 8 Ohms) Load Impedance

Stable from 2 - 16 Ohms Sensitivity 1.4Vrms , Signal

to Noise Ratio -weighted , Input Impedance Balanced

20K Ohms/Unbalanced 10K Ohms , Max Input

+20dBu Typical.

Supply,Installation,Testing & Commissioning of Digital No. 3 27140 81,420.00

Wireless handheld microphone system, 200 selectable

frequencies, RF Carrier Frequency Range -

CH1: 612.000 - 651.600 MHz (100 Selectable

Frequencies) CH2: 652.000 - 691.600 MHz (100

Selectable Frequencies), Audio Frequency

Range - 30Hz ~ 20 kHz, Signal-to-noise (A-weighted) -

120dB(A) , RF output - 50 mW max, Oscillation Mode -

Inside the chip VCO oscillation .

9 Supply,Installation,Testing & Commissioning of No. 4 3115.2 12,460.80

High Speed triple-shielded bonded pairs HDMI

Cable with Ethernet Gold Palted Lockable

Connector. It support Data Transfer rate of upto

minimum 10GBps and upto 48 bit Deep Color.

Cable has overall shield against EMI/RFI

interference and CL2 flame tested , Length

Supply,Installation,Testing & Commissioning of RM 100 141.6 14,160.00

Speaker Cable fof 2 Core 1.5 Sq. mm.,

stranded copper wire for maximum flexibility

and covered with a tough PVC jacket to

help prevent chafing,Wire should be

designed to maximize sound quality and for

better frequency response Cable with thickness

of 2 Core1.5 Sq. mm. .

Digitally signed by ARUN

Supply,Installation,Testing & Commissioning of RM 150 127.44 19,116.00

CAT6A U/FTP 4 shielded twisted pairs ,23AWG

solid copper conductor Video & LAN , Bulk Cable

— Low Smoke & Halogen Free recommended by

Supply,Installation,Testing & Commissioning of No. 1 45312 45,312.00

Equipment Rack , Size 24u u with front glass door

, rear vented MS door , Lockable both doors ,

Inbuilt fitted Blower & Castors with power

distribution panel.

Mis Interface Cables & Connectors Set 1 21240 21,240.00

Digitally signed by ARUN

Director's Room

S.No Description Qty Unit Rate Amount

1 Supply,Installation,Testing & Commissioning of Wall Hardware for the 1 Nos. 2,950.00 2,950.00

2 Supply,Installation,Testing & Commissioning of Wireless 1 Nos. 1,47,500.00 1,47,500.00

Presentation system with Operating system Windows 10 and higher

macOS 11 (BigSur) and higher , Android v9 and higher , iOS 12 and

higher (App) ; Video outputs 4K UHD (3840*2160) 30Hz. HDMI 1.4b

or USB-C DisplayPort 1.2 , Audio output HDMI, USB 1 X USB-A, 1 X

USB-C , Buttons 2nos ; Airplay, Google Cast, Miracast ; Maximum

number of simultaneous connections 32 ; Noise Level Max. 25dBA 0-

30°C , Max. 30dBA 30-40°C ; Authentication protocol WPA2-PSK in

stand alone mode , WPA2-PSK or IEEE 802.1X ; Wireless

transmission protocol IEEE 802.11 a/g/n/ac and IEEE 802.15.1.

3 Supply,Installation,Testing & Commissioning of High Speed triple- 4 RM 2,596.00 10,384.00

shielded bonded pairs HDMI Cable with Ethernet Gold Palted

Lockable Connector. It support Data Transfer rate of upto minimum

10GBps and upto 48 bit Deep Color. Cable has overall shield

against EMI/RFI interference and CL2 flame tested , Length

4 Supply,Installation,Testing & Commissioning of CAT6A U/FTP 4 100 RM 106.20 10,620.00

shielded twisted pairs ,23AWG solid copper conductor Video & LAN ,

Bulk Cable — Low Smoke & Halogen Free recommended by

5 Mis Interface Cables & Connectors 1 Nos. 14,160.00 14,160.00

Grand Total 1,85,614.00

Grand Total 1,85,614.00

Digitally signed by ARUN

CONFERENCE ROOM - Seating Capacity 40

S.No Description Qty Unit Rate Amount

1 Supply,Installation,Testing & Commissioning of Wall Hardware 1 Nos. 2,950.00 2,950.00

for the Display panel.

2 Supply , Installation , Testing & Commissioning of Matrix 4k No. 1 160480 1,60,480.00

Switcher Metal Chassis , with 6 nos Input slots (HDMI/DVI

/DisplayPort/HdBaseT ) , 2 nos. output , Resolution 4k

(4096x2160 ) , Input/Output Signal Types HDMI/DVI

/DisplayPort/HdBaseT,Advanced EDID management,HDCP

complaint , Audio output , Ethernet port 10/100 Mbps.

3 Supply, installation, testing & commissioning of PTZ ,Camera No. 1 150527.88 1,50,527.88

with HD Resolution Real High Definition Image with 1/2.3 inch

or higher high quality HD CMOS sensor , 1920 x 1080 super

high quality video ,20 x or more zoom with 20x or more digital

zoom, Pan Range: 170deg or more With HDMI output

interface for video & RS 232/ RS 422 for controls 10 or more

preset position.

4 Supply , Installation , Testing & Commissioning of Dual Channel 1 Nos. 69,502.00 69,502.00

Amplifier with utput 240W @ 4/8 Ohms (1kHz Power, THD+N<0.5%)

, Frequency Response +/- 1dB (@1W into 4 or 8 Ohms) Load

Impedance Stable from 2 - 16 Ohms Sensitivity 1.4Vrms , Signal to

Noise Ratio -weighted , Input Impedance Balanced 20K

Ohms/Unbalanced 10K Ohms , Max Input +20dBu Typical.

5 Supply , Installation , Testing & Commissioning of Ceiling Speakers No. 8 9385.72 75,085.76

with 30 Watts Continuous Power Handling, requency Range (-10 dB):

80 Hz - 20 kHz , Frequency Response (+/- 3 dB): 100 Hz - 18 kHz ,

Power Capacity1: 150 W , Sensitivity2: 87 dB SPL, 1 W 1 m (3.3 ft) ,

Maximum SPL3: 108 dB continuous, 114 dB peak.

6 Supply,Installation,Testing & Commissioning of Wireless 1 Nos. 1,47,500.00 1,47,500.00

Presentation system with Operating system Windows 10 and

higher macOS 11 (BigSur) and higher , Android v9 and higher

, iOS 12 and higher (App) ; Video outputs 4K UHD

(3840*2160) 30Hz. HDMI 1.4b or USB-C DisplayPort 1.2 ,

Audio output HDMI, USB 1 X USB-A, 1 X USB-C , Buttons

2nos ; Airplay, Google Cast, Miracast ; Maximum number of

simultaneous connections 32 ; Noise Level Max. 25dBA 0-

30°C , Max. 30dBA 30-40°C ; Authentication protocol WPA2-

PSK in stand alone mode , WPA2-PSK or IEEE 802.1X ;

Wireless transmission protocol IEEE 802.11 a/g/n/ac and

7 Supply,Installation,Testing & Commissioning of Digital Wireless 2 Nos. 27,140.00 54,280.00

handheld microphone system, 200 selectable frequencies, RF

Carrier Frequency Range - CH1: 612.000 - 651.600 MHz

(100 Selectable Frequencies) CH2: 652.000 - 691.600 MHz (100

Selectable Frequencies), Audio Frequency Range - 30Hz ~ 20

kHz, Signal-to-noise (A-weighted) - 120dB(A) , RF output - 50 mW

max, Oscillation Mode -Inside the chip VCO oscillation .

8 Supply,Installation,Testing & Commissioning of High Speed 2 Nos. 2,596.00 5,192.00

triple-shielded bonded pairs HDMI Cable with Ethernet

Gold Palted Lockable Connector. It support Data Transfer rate

of upto minimum 10GBps and upto 48 bit Deep Color.

Cable has overall shield against EMI/RFI interference and

CL2 flame tested , Length 1.8mtr..

Digitally signed by ARUN

9 Supply,Installation,Testing & Commissioning of CAT6A 150 RM 106.20 15,930.00

U/FTP 4 shielded twisted pairs ,23AWG solid copper

conductor Video & LAN , Bulk Cable — Low Smoke &

Halogen Free recommended by HDBaseT.

10 Supply,Installation,Testing & Commissioning of Speaker RM 100 141.6 14,160.00

Cable fof 2 Core 1.5 Sq. mm., stranded copper wire for

maximum flexibility and covered with a tough PVC

jacket to help prevent chafing,Wire should be

designed to maximize sound quality and for better

frequency response Cable with thickness of 2 Core1.5 Sq.

11 Mis Interface Cables & Connectors Set 1 21240 21,240.00

Digitally signed by ARUN

S.No Description Qty Unit Rate Amount

1 Supply,Installation,Testing & Commissioning 1 Nos. 2,950.00 2,950.00

of Wall Hardware for the Display panel.

2 Supply,Installation,Testing & 4 RM 3,115.20 12,460.80

Commissioning of High Speed triple-

shielded bonded pairs HDMI Cable with

Ethernet Gold Palted Lockable Connector. It

support Data Transfer rate of upto minimum

10GBps and upto 48 bit Deep Color. Cable

has overall shield against EMI/RFI

interference and CL2 flame tested , Length

3 Supply,Installation,Testing & 100 RM 141.60 14,160.00

Commissioning of CAT6A U/FTP 4 shielded

twisted pairs ,23AWG solid copper conductor

Video & LAN , Bulk Cable — Low Smoke &

Halogen Free recommended by HDBaseT.

4 Mis Interface Cables & Connectors 1 Set 11,800.00 11,800.00

Total 41,370.80

Digitally signed by ARUN

Detailed Estimate Based On DSR-2022 With Cost Index & Market Rate

Project - Proposed Composite Regional Centre (CRC) At Jamdoli, Agra Road, Jaipur (Rajasthan).

Name Of Work -External Electrical Work

Rate as per D.S.R. 2025 (For Rate as per D.S.R. 2022 MARKET BASED

Sr.No. Particulars Sch. No. Qty Unit Amount(Rs) per Amount(Rs) Rate(Rs) Amount(Rs)

A Subhead-I HT Work

1 11 KV DOUBLE POLE STRUCTURE

Supply, erection, testing and commissioning of 2 pole structure for providing

1 No. 11KV,200A GOS in accordance with IE rules, & local authority MR 1.00 Set 2,14,760.00 2,14,760.00

specification and drawings and comprising of the following.

a. 2 Nos. 11 mtr. long MS STEEL poles complete with, pole excavation, MS

STEEL foundation, and back filling complete MS steel channel/angle iron etc.

b. 1 Set of cross arms, branching, clamps and painting complete with GI nut,

bolts & washers as required (for GO & DO), LA connection.

c .1 set 11KV Insulator complete with spindles & hardware complete as

d .1 No. 11KV 400A TP Gang operated Air break switches complete with

25mm dia GI pipe operating machanism, handle & locking arrangement.

e. 1 set of 3 nos.11KV single pole drop out fuse complete with barrel fuses,

and mounting arrangement.

f. 1 set (3 nos.) 11KV lightning arrestor and connecting to all phases. - -

g. 4 No. 150 mm dia 6 meter long GI pipe class 'B' (for XLPE cable

protection) as required.

h. 2 Set 50mm dia 3m long GI pipe earting with 25 x 6 mm GI earth strip

complete as required (for GO & DO & LA)

i 1 nos. 11KV HT danger boards and 2 set of anticlimbing devices. - -

11 KV Double Pole Structure described below - -

Supply of 3 core standered aluminium conductor XLPE (Cross linked

polyethylene) insulated PVC bedded, Galvanised flat steel strip armoured

cables confirming to I.S. 7098 (Part-II with latest amendments) II KV grade

2 as per requirement. - -

Laying of one number PVC insulated and PVC sheathed / XLPE power cable

of 11 KV grade of following size direct in ground including excavation, sand

cushioning, protective covering and refilling the trench etc as required. DSR

Above 120 sq. mm and upto 400 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE

power cable of 11 KV grade of following size direct in ground in the same

trench in one tier horizontal formation including excavation, sand cushioning, DSR

4 protective covering and refilling the trench etc as required. 2022 - -

Digitally signed by ARUN

Above 120 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable

of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe DSR

5 as required. 2022 - -

Above 120 sq. mm and upto 400 sq. mm 8.3.2 150.00 Meter 134.00 20,100.00 - -

supplying and making indoor cable end termination with heat

shrinkable jointing kit complete with all accessories including lugs suitable for

following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as DSR

6 required : 2022 - -

Supplying and making outdoor cable end termination with heat shrinkable

jointing kit complete with all accessories including lugs suitable for following

size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : DSR

Supply and laying of 1800mm x 900mm x 12mm thick chequered rubbbber

8 matting of tested quality. MR 8.00 Each 3,452.60 27,620.78

Supply and fixing of shock treatment chart (prescribed under I.E. rules) duly

framed with glass and supported from back with hard board or soft board with

supply of all material labour T&P for proper completion of work.

Supply and fixing of C02 type fire extinguisher 4.5 kg. capacity (ISI Marked

IS : 2878 & TAC approved) complete with initial charge and wall bracket,

along with supply of all materials and labour for proper completion of work.

Supply and laying of PVC Insulated, FRLS Round Sheathed Multi Core

Industrial Flexible Cable conforming to IS 694:2010 with Flexible Bright

Annealed Copper Conductor for Voltage Grade 1100 Volts as per direction of

11 engineer incharge. - -

S.I.T.C. of VCB's Indoor Type as per latest specification of UP Power

Corporations, make prefered Cromptron,Schneider or any Equivalent make

approved by UP Power Corporation. Including construction of Plinth and

earthing etc. with all material as per Technical Requirment. with 05 years

12 warranty - -

Total For Subhead-I HT Work 2,08,774.00

B Subhead-II Transformer

1 TRANSFORMER - -

Digitally signed by ARUN

11/0.433 KV, 3 Phase, 50 Hz outdoor/ indoor mounting(Mineral oil

Supply, installation, testing and commissioning of following capacity

(continuous loading) BEE 3 Star rated (Corresponding Level as per BIS

amended upto date of receipt of tender) , 11/0.433 KV step down, 3 Phase,

50 Hz, Dyn 11 vector group, ONAN (Oil Natural Air Natural) copper wound

transformer (Electrolytic grade 99.9% pure copper, Core made of first grade

Cold Rolled Grain Oriented (CRGO) Core grade MOH or better, suitable for

out door/indoor applications with On Load Tap Changer (OLTC) on HV side

having AVR relay and Remote Tap Changer Control (RTCC) for automatic

sensing of incoming voltage, automatic operation of OLTC and facility for

remote and manual operation of OLTC HV side in range of +5% to-15% in

steps of 2.5%, having cable end boxes on HV side suitable for 3x300 sqmm -

XLPE cable of 11 KV grade, including bus trunking arrangement on LV side

including supplying and laying of copper conductor multicore control cable

from transformer to HT breaker/panel for safety tripping, complete with all

accessories and safety provisions as per relevant

IS Code including first filling of filtered dehydrated oil, i/c supplying and

grouting of suitable M.S. Channel with all accessories and transformer shall

be confirming to IS : 2026 (Part 1 to Part 5), IS : 1180 and duly ISI Marked

and as per CPWD specifications complete in all respects etc as required at

site. The maximum flux density in any part of the core and yoke at rated

voltage and frequency shall be such that the flux density with + 12.5 percent -

combined voltage and frequency variation from rated voltage and frequency

does not exceed 1.9 Tesla. The permissible temperature-rise shall not

exceed 35 dg.C for oil and 40 dg. C up to 200 KVA and 40 dg.C for oil and

dg. C for above 200 KVA for winding. Inside of tank shall be painted with

varnish or liquid resistant paint. For external surfaces one coat of thermo

setting powder paint or one coat of epoxy primer followed by two coats of

polyurethane base paint shallbe used. IS: 1180 (Part 3) shall be referred to

for paint thickness for normal to medium corrosive atmosphere. For highly

polluted atmosphere and special application external paint work shall be as

per direction of Engineer-in-Charge. Design ambient condition : a) air

temperature 50 deg C, b) Relative Humidity 90 % Max, c) Seismic Zone as

per location of site, d) Altitude as per location/site. Noise level Shall not

exceed limits as per NEMA TR-1 with all accessories running measured as

per IEC 551 / NEMA standard. The transformer should have QR code which

should contain drawing, test report OEM manual,Geo- Tag of manufacturing

location etc. Marking Each transformer shall be provided with rating plate

made of anodized aluminum/ stainless steel material securely fixed on the

outer body, easily accessible,as per IS: 1180 Part-3. The entries on the rating

plate shall be indelibly marked. -

Digitally signed by ARUN

Fitting and Accessories : The following fittings shall be provided:- a) Two

earthing terminals with the earthing symbol b) Oil level gauge indicating oil

level at minimum, 30°C and maximum operating temperature; c) Air release

device (for non-sealed type transformers) d) Rating and terminal marking

plates; e) Silica gel breather f) Drain-cum-sampling valve (¾″ nominal size

thread, IS 554) preferably steel with plug for three phase transformers; g)

Thermometer pocket with cap; h) Oil filling holes having (1¼″ nominal size

thread) with cover (for sealed type transformers without conservator); i)

Lifting lugs for the complete transformer as well as for core and winding

assembly; j) Pressure relief device or explosion vent above 200 kVA; k) One

filter valve on the upper side of the tank (for transformers above 200 kVA); l) -

Unidirectional flat rollers (for transformers above 200 kVA); m) Inspection

hole (for transformers above 200 kVA); n) HV side neutral grounding strip

(where one of the HV bushing terminal is connected to earth);

o) Buchholz relay for transformers above 800 kVA. p) Arcing horns or

suitable rating lightning arrestors for HT side – 3 Nos. q) Bird guard; r) Oil

temperature indicator and winding temperature indicators for transformers

above 200 kVA with suitable tripping mechanism above permissible limit s)

Jacking pads (for transformer above 1 600 kVA); t) Additional Neutral

separately brought out on bushing for earthing. u) Magnetic oil level gauge

(for transformer above 1600 kVA) with low oil level alarm contact; v) Non

return valve (for conducting pressure test); w) Pressure relief device or

explosion vent x). Monogram Plate y) Inspection cover z). Detachable type DSR

radiators with top and bottom shutoff valve. aa) Oil Conservator with Oil

indicator, minimum level marking and drain plug for all transformers of

capacity 50 KVA and above. bb) Necessary hardware, clamps, lugs etc. for

termination on HV/MV etc. for all transformers.

Total For Subhead-II Transformer 6,73,755.00

C Subhead-III DG Set

Supply, installation, Testing & Commissioning of 'Silent Type Diesel

Generating set as per CPCB IV + or better norms along with having Prime

Power Rating of KVA as below, 415 volts at 1500 RPM, 0.8 lagging power

factor at 415 V suitable for 50 Hz, 3 phase system & for 0.85 Load Factor,

including testing at factory and site with fuel, load for test and other

necessary arrangements Complete as per CPWD specifications, should

have QR code which should contain drawing, test report OEM manual,Geo-

Tag of manufacturing location, rating plate as per relevant IS Code etc. and DSR

consisting of the followings: 2025 - -

(A) Diesel Engine:

Turbocharged Diesel engine 4 stroke water cooled, multi cylinder,

dynamically balanced fly wheel, electric start of suitable BHP at 1500 RPM

suitable for above output of alternator at 40 Degree C, 50% RH & at 1000

Meter MSL , capable of taking 10% over loading for one hour after 12 hours

continuous operation. The engine will be with Electronic governor, Dry type

Air filter with service indicator, first filling of engine fuel (after

lubricating Oil, Coolant and other consumables complete with all the

required accessories, the Electronic governor shall be as per ISO 8528.The

engine shall comply to the latest CPCB norms (CPCB IV + or better) and

Conforming to BS 5514, BS 649, IS 10000, IS 10002, IS 13018 and as per

CPWD specifications.

(B) Engine mounted Instrument Panel fitted with and having digital display

Digitally signed by ARUN

(i) Start-stop switch with key

(ii) Water temperature indication

(iii) Lubrication oil pressure indication

(iv) Lubrication oil temperature indication

(v) Battery charging indication and Voltage indication

(vi) RPM indication

(vii) Over speed indication

(viii) Low lubricantion Oil trip indication

(ix) Engine Running Hours indication

(C) Alternator:

Synchronous alternator rated of appropriate KVA, 415 volts at 1500 RPM, 3

phase 50 Hz, AC supply with 0.8 lagging power factor at 40 Degree C, 50%

RH & at 1000 Meter MSL. The alternator shall be having Screen Protected

Drip Proof (SPDP) enclosure IP23, brushless, continuous duty, dynamically

balanced rotor, capable of taking 10% over loading for one hour after 12

hours of continuous operation, self cooled,self-excited and self-regulated

through AVR conforming to IS13364(Part 2)/IS: 4722/BS 2613 suitable for

tropical conditions and with class- H insulation.

(D) Base Frame & Foundation:

Both the engine and alternator shall be mounted on suitable base frame

made of MS channel with necessary reinforcement which shall be installed

on suitable cement concrete foundation and vibration isolation arrangement

as per recommendations of manufacturer.

Daily service fuel tank of suitable liters capacity as per CPWD Specifications,

fabricated out of 3 mm thick M.S. sheet complete with all standard

accessories and fuel piping between fuel tank and diesel engine with MS

class 'C' pipes of suitable dia. Complete with valves, level indications &

accessories as required as per specifications.

(F) Exhaust System:

Dry exhaust manifold with hospital type exhaust silencer and catalytic

(G) Starting System:

12V/24V DC starting system comprising of starter motors: voltage

regulator and arrangement for initial excitation complete with suitable

numbers of batteries (180 AH capacity lead acid SMF type) as required as

per specifications. The battery shall be housed inside the acoustic enclosure

(H) Acoustic and weather proof enclosure with arrangement for fresh air

intake for cooling of the engine & alternator, extraction, discharging hot air in

to the atmosphere and the temperature rise inside the enclosure, noise level

outside enclosure. The acoustic enclosure should be suitable for cable

connection/connection through bus-trunking. Such arrangements on

acoustic enclosure should be water proof & dust-proof conforming to IP-65

protection. The enclosure shall be as per CPCB IV + or better norms etc. and

as per CPWD specifications.

Digitally signed by ARUN

Free standing floor mounted IP 42 automatic mains failure control panel

including auto by-pass, suitable for KVA as below for silent type DG set

complete with relays, timers, set of CTs for metering & protection and energy

analyser to indicate currents, phase and line voltages, frequency, power

factor, KWH, Kilo Volt Ampere Reative Hour (KVARH), KVA (Phase &

KW & provision for overload, short circuit, restricted earth fault, under

frequency, power (aluminum) and control (copper ) cabling of suitable size

upto 15 meter between AMF panel, LT Panel and DG Set including

connection interconnection etc. as required, all complete and inter locking

and communication/ Ethernet /RS485/SNMP port open protocol for BMS

integration including suitable software, the panel shall be of DG Set OEM

make etc. as per approved by Engineering in charge and including the

1. Suitable numbers and appropriate capacity 4 pole motorised

electrically operated draw out with cradle type 3 position ACB/ MCCB

with electronic release for O/C & E/F and shunt trip.

2. Auto/Manual/Test/Off selector switch

3. Protection for under and over voltage phase reversal (2 nos Over

voltage relay, 2 Nos. reverse power relay and 2 Nos. under voltage

4. 3 Sets of current transformers 15 P 10 accuracy for protection and 15

VA class-I for metering

5. Energy analyser unit to indicate current, Voltage( L-N & L-L), kW, kVA

(Phase & Total), Frequency, KWH, PF.

6. LED Indicating lamps for load on mains and load on set.

7. Fuse/ MCB for instruments.

8. Battery charger, complete with transformer/ rectifier, D.C. voltmeter

and ammeter, selector switch for trickle, off and boost and current

9. Main supply failure monitor.

10. Supply failure timer.

11. Restoration timer

12. Control unit with three impulse automatic engine start/stop and failure

to start lockout.

13. Impulse counter with locking and reset facility.

14. ON/OFF/Control circuit switch with indicator

15. Audio/Video annunciation for

(i) High water temperature

(ii) Low lubricating oil pressure

(iii) Engine over speed

(iv) Engine fails to start

(v) Full load/maximum load warning

16. Protection for over/under Frequency, Loss of AC sensing, Over

Current, Unbalancing load with suitable number of relays and

17. Maintenance notification based on Engine Run Hour & due date.

18. Load Management through PLC to achieve auto opening and closing of

incomer breakers, bus coupler switching of essential panel ,

interlocking providing signal to AMF Panel for load status and AMF

shall give command to DG Set to auto start / auto stop depending upon

load status and requirement etc. and necessary hardware and

software required to perform the operation shall be provided by the

160 KVA including all control wiring. 6.1.9 1.00 Each 11,87,133.00 11,87,133.00 -

Total For Subhead-III DG Set 11,87,133.00 - -

D Subhead-IV Distribution Panel

SITC of LT switchgear panels suitable for 433 V, 3 phase, 4 wire, 50 Hz

power distribution system. The panel shall be Indoor, free standing, floor

mounting, sheet metal clad, cubicle, dead front, dust and vermin proof type

compartmentalised design fabricated out of 14 SWG CRCA sheet steel,

complete with colour coded, heat shrinkable PVC insulated, aluminium bus

bars and separate earth bus bar of adequate cross section through out the

length of the panel. The incoming and outgoing feeders shall be

accommodated in a fully segregated, modular multitier arrangement with - -

adequate size and distinct cable alley, bus bar alley/chamber. The panel shall

be complete with name plate, earthing, numbering, danger plate etc. as per

specifications and drawings as required. The panel shall withstand the fault

level of 50kA as per Single Line Diagram. The Panel shall also be capable to

communicate status like ON/OFF/ Trip through Modbus/Ethernet for major

component like ACB, MCCB, MCB & Multifunation meters.

Digitally signed by ARUN

The Main LT Panel shall use all draw out type breakers suitable for 415 V

AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. Panel shall have

Buscoupler switching, auto operation of incommer and bus coupler, auto start

of D.G. Sets, auto D.G. running by pre set timing, auto changeover etc and

having following incomming and outgoing Air Circuit

Breakers,microprocessor release for overload, short circuit, instantaneous &

earthfault protection with Current & Voltage metering & LCD display. - -

Air Circuit Breaker with microprocessor release ge metering & LCD display ,

with ready to clsoe indicator, should have capability to communicate ON

/OFF/ Trip Status on Modbus/Ethernet and as per the detail specification of

ACB (Icu=Ics=Icw=65 KA (1 sec). MCCB, with microprocessor release

with LSIG protection functionand should not derate upto 50 decree

Centrigrate as per testing guideline as per IEC 60947-2 and all the ACB upto

2500Amp ACB should have same frame size LCD display for fault trip

history, haivng current limiting feature, double break mechanism & capability

to communicate ON /OFF/ Trip Status on Modbus/Ethernet. (65 KA Ics) - -

1 Nos. 800 Amp TPN EDO ACB 25KA LSIG having S/C, E/F O/C

protection, LCD Display having specs as per attached annexture From

800KVA Transformer having

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB

Inbuilt Zone Slelective Interlocking function - -

Multifunction Meter

1 Nos. 320 Amp TPN EDO ACB 25KA LSIG having S/C, E/F O/C

protection, LCD Display having specs as per attached annexture From

200KVA Solar Power Backup having

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB

Inbuilt Zone Slelective Interlocking function

Multifunction Meter - -

Reverse Power Relay

Power Conditioning Device

1 Nos. 125 Amp TPN EDO ACB 25KA LSIG having S/C, E/F O/C

protection, LCD Display having specs as per attached annexture From

200KVA Solar Power Backup having

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB

Inbuilt Zone Slelective Interlocking function

Multifunction Meter - -

Reverse Power Relay

Power Conditioning Device

BUSCOUPLER - -

1 Nos. 320Amp TPN EDO ACB 25KA having specs as per attached

annexture having

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB

1 Nos. 1000 Amp FP busbars of aluminium alloy as per SLD.

1 Nos. 400 Amp FP busbars of aluminium alloy as per SLD.

1 Nos. 400 Amp TP MDO MCCB 25 KA, having specs as per attached

annexture having

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB - -

Digitally signed by ARUN

2 Nos. 500 Amp FP EDO MCCB 25 KA, having specs as per attached

annexture having

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB

Officre L+P + FF + Spare

3 Nos. 315 Amp FP EDO MCCB 25 KA, having specs as per attached

annexture having

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB - -

Officre L+P + FF + Spare

3 Nos. 160 Amp FP MCCB 25 KA

On, Off, Trip Status Indication with control MCB

Multifunction Meter

STP + PL + Spare

3 Nos. 100 Amp FP MCCB 25 KA

On, Off, Trip Status Indication with control MCB

Multifunction Meter - -

6 Nos. 63 Amp FP MCCB 25 KA

On, Off, Trip Status Indication with control MCB

Multifunction Meter - -

EX LIGHT + LIFT +Spare

Short Circuit Breaking capacity should not less than 25KA.

RELAYS AS PER SLD - -

200KVAR APFC PANEL TTA

Automatic Power Factor Correction (APFC) System

Supply, Installation, testing and commissioning of Automatic Power Factor

Correction (APFC) panel, indoor type floor mounted free standing totally

enclosed, extendable, IP 42, of following capacity for 3 phase, 415 V + 10 %,

50 Hz AC System for Ambient temperature -5°C to +40°C, fabricated in

compartmentalized designed made of CRCA sheet steel of 2.0mm thick for

framework & covers, 3 mm thick for gland plate i/c cleaning & finishing

complete with 9 tank process for powder coated of approved shade ( RAL - -

7032-Siemens gray or as approved by Engineer-in-Charge), having front

section (switch gear and control accessories) and rear section capacitor and

reactor, front and rear access, having suitable current carrying capacity,

extensible TPN Aluminum alloy bus bar of high conductivity, DMC/SMC bus

bar supports, bottom base channel of MS Section, fabrication shall be done

in transportable section, entire panel shall have common copper earth bar of

minimum size of 25mm x 5mm with 2 nos. earth studs, the earth terminals

provided on the body of capacitor bank shall also be bonded to the main

capacitor panel earth bus with 2 nos. 8 SWG or 6 SWG GI earth wires/

equivalent size of copper conductor cable, forced ventilation for maintaining

temperature rise not more than 5°C from ambient, interconnections,

connections with 14% detuned reactor and heavy duty 525 V ISI marked - -

Impregnated MPP(Metalized Polypropylene) Capacitor (IS 13340 Part -1 &

2) APFC Panel shall be in compliance with IS :16636 & CPWD

Specifications etc. as per below details

Suitable capacity MCCB Microprocessor base with O/C, S/C, E/L release of

TPN 50KA breaking capacity (Ics=Icu), ON, OFF, Trip, R, Y, B - LED

Indicating Lamp set along with required Instruments and accessories with

extended rotary handle and door interlocking arrangement. Current rating of

the Incomer in ampere shall be APFC Panel rating in KVAR x 1.4 x 1.5 or

Nearest higher standards rating.

(B) Instruments & Indications

i) 3-Phase current sensing APFC microprocessor relay/controller , advance

8/12 stages (8 stages for capacity below 100 KVAR and 12 stages 100

& above) with Communication Ethernet/RS485/SNMP port open protocol for

BMS integration as per approved by Engineering in charge and having

display of Phase wise V, A, PF, Cos-Phi, Kw, KVA, KVAR, THD-V , THD-I,

harmonics up to 31 level. 3 nos of dual core CT's accuracy class 1, 15VA at

incomer of PCC Panel for APFC relay.

Digitally signed by ARUN

ii) Auto Manual Selector switch, auxiliary contactors with timer for delay in

iii) Digital Multi function meter with LED Display for V, A, PF, KW, KVA,

KVAR, THD-V & I, Frequency.

iv) Suitable rating control transformer shall be provided for control and

indication circuit. - -

shall be protected by using suitable rating individual MCB's.

vi) Wiring of the control circuit shall be done by using 2.5 sq mm, FRLS

V grade, PVC insulated multi stranded copper control wire.

1.3 Amp per Sq.mm, TPN, Electrolytic grade Aluminum bus bar of capacity

1.25 times of incomer rating as per CPWD specification.

(D) Outgoings (APFC Section)

Selection of the capacitors combinations shall be for continuous rating and

each capacitor bank shall have suitable capacity Heavy Duty ISI Marked - -

Capacitor, capacitor duty contactor, the capacitor shall be mounted on

channel with base of perforated M S Powder coated sheet, connections inter

connections etc. and other features as per CPWD Specifications and

relevant IS Code having following:

(i) Capacitor bank ratings & stages shall be as per the technical

specifications sheet of NIT.

(ii) Capacitor will be MPP self healing type with discharge resistor, pressure

release mechanism.

(iii) Since Capacitor Voltage is 525 Volts, thus higher KVAR has to be

considered to get rated output at 415 Volts.

(iv) 14% Detuned Reactor of class H insulation & 150% linearity in series

(Note: Technical specifications sheet for selection of the capacitors - -

combinations shall be provided by the NIT Approving Authority with due

consideration of number of capacitors i.e. 1 KVAR, 2 KVAR, 3 KVAR, 5

KVAR, 10 KVAR.....for smooth correction).

Office Building L+P Panel

SITC of LT switchgear panels suitable for 433 V, 3 phase, 4 wire, 50 Hz

power distribution system. The panel shall be Indoor, free standing, floor

mounting, sheet metal clad, cubicle, dead front, dust and vermin proof type

compartmentalised design fabricated out of 14 SWG CRCA sheet steel,

complete with colour coded, heat shrinkable PVC insulated, aluminium bus

bars and separate earth bus bar of adequate cross section through out the

length of the panel. The incoming and outgoing feeders shall be

accommodated in a fully segregated, modular multitier arrangement with - -

adequate size and distinct cable alley, bus bar alley/chamber. The panel shall

be complete with name plate, earthing, numbering, danger plate etc. as per

specifications and drawings as required. The panel shall withstand the fault

level of 50kA as per Single Line Diagram. The Panel shall also be capable to

communicate status like ON/OFF/ Trip through Modbus/Ethernet for major

component like ACB, MCCB, MCB & Multifunation meters.

The Main LT Panel shall use all draw out type breakers suitable for 415 V

AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. Panel shall have

Buscoupler switching, auto operation of incommer and bus coupler, auto start

of D.G. Sets, auto D.G. running by pre set timing, auto changeover etc and

having following incomming and outgoing Air Circuit

Breakers,microprocessor release for overload, short circuit, instantaneous &

earthfault protection with Current & Voltage metering & LCD display. - -

Air Circuit Breaker with microprocessor release ge metering & LCD display ,

with ready to clsoe indicator, should have capability to communicate ON

/OFF/ Trip Status on Modbus/Ethernet and as per the detail specification of

ACB (Icu=Ics=Icw=65 KA (1 sec). MCCB, with microprocessor release

with LSIG protection functionand should not derate upto 50 decree

Centrigrate as per testing guideline as per IEC 60947-2 and all the ACB upto

2500Amp ACB should have same frame size LCD display for fault trip

history, haivng current limiting feature, double break mechanism & capability

to communicate ON /OFF/ Trip Status on Modbus/Ethernet. (65 KA Ics) - -

Digitally signed by ARUN

1 Nos. 315 Amp MCCB 16KA LSIG having S/C, E/F O/C protection, LCD

Display having specs as per attached annexture

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB

Inbuilt Zone Slelective Interlocking function

Multifunction Meter

1 Nos. 400 Amp FP busbars of aluminium alloy as per SLD.

12 Nos. 63 Amp FP MCB 10 KA

On, Off, Trip Status Indication with control MCB

PDB+ACDB +Spare - -

9 Nos. 63 Amp FP MCB 10 KA

On, Off, Trip Status Indication with control MCB

LDB +Spare - -

Short Circuit Breaking capacity should not less than 16KA.

RELAYS AS PER SLD - -

Office Building HVAC Panel

SITC of LT switchgear panels suitable for 433 V, 3 phase, 4 wire, 50 Hz

power distribution system. The panel shall be Indoor, free standing, floor

mounting, sheet metal clad, cubicle, dead front, dust and vermin proof type

compartmentalised design fabricated out of 14 SWG CRCA sheet steel,

complete with colour coded, heat shrinkable PVC insulated, aluminium bus

bars and separate earth bus bar of adequate cross section through out the

length of the panel. The incoming and outgoing feeders shall be

accommodated in a fully segregated, modular multitier arrangement with - -

adequate size and distinct cable alley, bus bar alley/chamber. The panel shall

be complete with name plate, earthing, numbering, danger plate etc. as per

specifications and drawings as required. The panel shall withstand the fault

level of 50kA as per Single Line Diagram. The Panel shall also be capable to

communicate status like ON/OFF/ Trip through Modbus/Ethernet for major

component like ACB, MCCB, MCB & Multifunation meters.

The Main LT Panel shall use all draw out type breakers suitable for 415 V

AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. Panel shall have

Buscoupler switching, auto operation of incommer and bus coupler, auto start

of D.G. Sets, auto D.G. running by pre set timing, auto changeover etc and

having following incomming and outgoing Air Circuit

Breakers,microprocessor release for overload, short circuit, instantaneous &

earthfault protection with Current & Voltage metering & LCD display. - -

Air Circuit Breaker with microprocessor release ge metering & LCD display ,

with ready to clsoe indicator, should have capability to communicate ON

/OFF/ Trip Status on Modbus/Ethernet and as per the detail specification of

ACB (Icu=Ics=Icw=65 KA (1 sec). MCCB, with microprocessor release

with LSIG protection functionand should not derate upto 50 decree

Centrigrate as per testing guideline as per IEC 60947-2 and all the ACB upto

2500Amp ACB should have same frame size LCD display for fault trip

history, haivng current limiting feature, double break mechanism & capability

to communicate ON /OFF/ Trip Status on Modbus/Ethernet. (65 KA Ics) - -

1 Nos. 500 Amp ACB 16KA LSIG having S/C, E/F O/C protection, LCD

Display having specs as per attached annexture

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB

Inbuilt Zone Slelective Interlocking function

Multifunction Meter

1 Nos. 650 Amp FP busbars of aluminium alloy as per SLD.

Digitally signed by ARUN

20 Nos. 63 Amp FP MCB + 63 Amp 300mAmp FP RCCB

On, Off, Trip Status Indication with control MCB

11 Nos. 63 Amp FP MCB 10 KA with 3-5KW S tar Delta Starter With

Potential Free Contact to be operated as per Fire Alarm Panel Command

On, Off, Trip Status Indication with control MCB

Ventilation & Pressurization Fan +Spare

Short Circuit Breaking capacity should not less than 16KA.

RELAYS AS PER SLD - -

5 UPS Output Panel MR 1.00 Set 1,12,100.00 1,12,100.00

SITC of LT switchgear panels suitable for 433 V, 3 phase, 4 wire, 50 Hz

power distribution system. The panel shall be Indoor, free standing, floor

mounting, sheet metal clad, cubicle, dead front, dust and vermin proof type

compartmentalised design fabricated out of 14 SWG CRCA sheet steel,

complete with colour coded, heat shrinkable PVC insulated, aluminium bus

bars and separate earth bus bar of adequate cross section through out the

length of the panel. The incoming and outgoing feeders shall be

accommodated in a fully segregated, modular multitier arrangement with - -

adequate size and distinct cable alley, bus bar alley/chamber. The panel shall

be complete with name plate, earthing, numbering, danger plate etc. as per

specifications and drawings as required. The panel shall withstand the fault

level of 50kA as per Single Line Diagram. The Panel shall also be capable to

communicate status like ON/OFF/ Trip through Modbus/Ethernet for major

component like ACB, MCCB, MCB & Multifunation meters.

The Main LT Panel shall use all draw out type breakers suitable for 415 V

AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. Panel shall have

Buscoupler switching, auto operation of incommer and bus coupler, auto start

of D.G. Sets, auto D.G. running by pre set timing, auto changeover etc and

having following incomming and outgoing Air Circuit

Breakers,microprocessor release for overload, short circuit, instantaneous &

earthfault protection with Current & Voltage metering & LCD display. - -

Air Circuit Breaker with microprocessor release ge metering & LCD display ,

with ready to clsoe indicator, should have capability to communicate ON

/OFF/ Trip Status on Modbus/Ethernet and as per the detail specification of

ACB (Icu=Ics=Icw=65 KA (1 sec). MCCB, with microprocessor release

with LSIG protection functionand should not derate upto 50 decree

Centrigrate as per testing guideline as per IEC 60947-2 and all the ACB upto

2500Amp ACB should have same frame size LCD display for fault trip

history, haivng current limiting feature, double break mechanism & capability

to communicate ON /OFF/ Trip Status on Modbus/Ethernet. (65 KA Ics) - -

1 Nos. 125 Amp MCCB 16KA

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB

Inbuilt Zone Slelective Interlocking function

Multifunction Meter

1 Nos. 160 Amp FP busbars of aluminium alloy as per SLD.

8 Nos. 32 Amp FP MCB

On, Off, Trip Status Indication with control MCB

UPS DB +Spare - -

Short Circuit Breaking capacity should not less than 16KA.

RELAYS AS PER SLD - -

Total For Subhead-IV Distribution Panel

Digitally signed by ARUN

E Subhead-V L.T Cable Work

Supply of Power Cables,Solid Aluminum conductor up to 10 sqmm balance

stranded conductor,XLPE Insulated,cores laid up, PVC tape

innersheathed,unarmoured/Armour(Aluminium wire for single core up to 70

sqmm balance Aluminium strip, Glavanised wire for cables upto 2x16 sqmm,

3x10 sqmm & balance all galvanised steel strip),extruded PVC Type ST2

sheathed,650/1100V grade as per IS 7098(Part 1) 1988

a 6 sq. mm 2 core RA-8 Meter 132.12 -

e 95 sq. mm 3-1/2 core RA-12 - Meter 727.10 -

Supply ofPower/Control Copper Cables,Solid Copper conductor,XLPE

Insulated,cores laid up, PVC tape innersheathed,Unarmoured/Armour

(Glavanised wire for cables up to 14x1.5 sqmm, 9x2.5 sqmm,2x16 sqmm,

3x10 sqmm,4x10sqmm balance all galvanised steel strip),extruded PVC Type

ST2 Sheathed, 650/1100 V grade as per IS 7098 (Part 1) 1988