PERIODICAL SERVICES TO BLDG IN YOS WING AND SARAGARHI IN INF SCHOOL AND REPAIR REPLACEMENT TO FLOORING PLASTERING PLUMBING JOINERY SANITARY FITTING AND CERTAIN MISC WORKS IN ZONE D AREA OF AGE BR I UNDER GE MIS MHOW

Amount

M&L for complete removal of existing treatment from wall /roof projections including facis, cornics etc and scrapping internal surfaces by using mechanical sander (having mechanical vaccum mechanism) with sanding pad of appropriate grit to make surface clean, free from dust, loose paint etc and external surface by using Jet washer and appropriate skilled labour complete all as specified and directed.

M & L for providing and applying 1mm thick (minimum) wall care putty over prepared surface of wall and rubbing it with mechanical sander (having mechanical vaccum mechanism) to achive the surface even and smooth for further application of finishes complete all as specified and directed.

M&L for applying two coats of 100% Premium arcylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance , dirt resistance exterior paint of required shade over and including priming coat of exterior primer by using proper spraying machine complete all as specified and directed Make :- Nerolac -Excel, Asian - Apex, Burger - Weather coat antidust, Dulux - Weather shield. Note: - (a) Application of Primer and emulsion shall be carried out through air less spray machine (Mechanical method (b) Wall care putty (if required at site before application of above painting at certain portion of area ) shall be done and same shall be measured and paid seperately under serial item No 02

M & L for applying two coats of Acrylic Emulsion having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour over and including a coat of primer by using proper roller complete all as per Manufacturer's instruction complete all as specified and directed. Make: Nerolac-Little Master(Beauty), Berger-Bison Lite, Asian- Tractor emulsion spark. Note: (a) Application of Primer and distemper shall be carried out through Roller (Mechanical methoad) (b). Wall care putty (if required at site before application of above painting at certain portion of area) shall be done and same shall be measured and paid seperately under serial item No 02

M & L for preparation of old surfaces of wall and applying two coats of white wash complete all as specified and directed.

M & L for preparation of old treated surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M & L for preparation of old treated steel surfaces of any description exceeding 10cm in width or girth and applying one coat of synthectic enamel paint complete all as specified and directed.

M & L for preparation of old treated wood or wood based surface of any description exceeding 10cm in width or girth and applying one coat of synthectic enamel paint complete all as specified and directed.

M & L for preparation of old treated steel surfaces of any description exceeding 10cm in width or girth and applying two coats of synthectic enamelled paint complete all as specified and directed.

M & L for preparation of old treated wood or wood based surface of any description exceeding 10cm in width or girth and applying two coats of synthectic enamel paint complete all as specified and directed.

M&L for preparation of old decorated surfaces with white cement base putty in patches as required and applying one coat of exterior weather proof water base emulsion paint of following make on walls complete all as specified & directed Note:-wall care putty (if required at site before application of above painting at certain portion of area) shall be done and same shall be measured and paid seperately under serial item No 02 Make :- Asian-ACE, Berger-Wall Masta, Nerolac Suraksha

M&L for preparation of old decorated surfaces with white cement base putty in patches as required and applying two coats of exterior weather proof water base emulsion paint of following make on walls complete all as specified & directed Note:- Wall care putty (if required at site before application of above painting at certain portion of area) shall be done and same shall be measured and paid seperately under serial item No 02 Make :- Asian-ACE, Berger-Wall Masta, Nerolac Suraksha

M & L for Washing, rubbing down and stopping of distempered and painted surfaces for application of Acrylic emulsion paint over prepared wall surfaces complete all as specified and directed.

M&L for applying one coat of Acrylic Emulsion having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour over and including a coat of primer by using roller complete all as per manufacturer's specification and as specified and directed. Make: Nerolac-Little Master(Beauty), Berger-Bison Lite, Asian- Tractor emulsion spark. Note : (a) Application of Primer and emulsion shall be carried out through Roller (Mechanical method) (b) Wall care putty (if required at site before application of above painting at certain portion of area) shall be done and same shall be measured and paid seperately under serial item No 02

M&L for removal of plants/trees of girth not exceeding 30 cm from roof/sides, external walls of building chajjas, wall junctions, junctions of rain water pipe/ CI soil/waste pipe junction including taking out the roots entered in wall/slab surfaces and making good the disturbed surface with PCC (1:2:4) type B0 or cement mortar (1:2) including making good the joints of GI/CI/PV pipe if damaged during execution to match with existing including necessary scaffolding/staging upto a height of 15.00 m from the ground level complete all as specified as directed by Engineer -in-Charge. Note :(a) CI/AC/PVC pipes or pipe fitting damage during the process of work shall be replaced by contractor with new one without any extra cost to Govt. The decision of the GE on this regard shall be final and binding. (b) The debris including vegetation plant/trees shall be disposed off to a distance exc 0.5 Km but n.exc 1.00 Km all as directed by Engineer-in- charge. (c) Girth of the plant/tree the height shall be measured at 30 cm above the slab/wall. (d) Contractor shall provide necessary safety equiptments, tool , ledder etc to carryout the work and work shall be carried out carefully without damaging teh building surfaces.

Supply and applying crack filler for filling of cracks on wall surfaces by cutting and making V-groove in crack to a width n.exc 10mm and depth n.exc 10mm filling with approved crack filler and finish the surface even and smooth complete all as specified and directed.

Demolition of brick work built in cement mortar including all quions ,arches , pillars etc complete all as specified and as directed.

M&L for Brick work with sub class 'B' bricks with using Modular size Brick , straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed .

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M & L for rendering 15mm thick plaster in CM (1:6) on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for applying 2mm thick wall care putty on newly plastered surface of wall and prepared to smooth finish all as specified and directed.

M & L for rendering 15mm thick plaster in CM (1:4) on fair faces of brick work or concrete surfaces mixed with Dr fixit pidiproof LW 200ml/50Kg of cement , finished the surface even and smooth without using extra cement all as specified and directed. Note: WPC shall be measured and paid separatily under relevant item.

M&l for rendering 5mm thick in cement mortar 1:3 on concrete surface in ceiling ,mixed with Dr fixit pidiproof LW 200ml/50Kg of cement and finished even and smooth without using extra cement all as specified and directed.

Supply only liquid water proofing compound

M&L for preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

M&L for newly plastered ceiling surface and applying of two coats of oil bound distemper over a coat of Chawlk whiting/cement based wall primer and all as specified and directed.

Dismantling of floor, hearth , or wall tiling including cement mortar bedding ( but not backing ) and rubbish off the primeses complete all as specified and directed.

M&L for glazed ceramic coloured tiles 450X300X 6mm to 7mm thick as in vertical surface as in skirting/dados , set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile over and including 10 mm thick rendering in CM 1:4 complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7-8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exc 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile over and including 15mm thick screed bed or bedding layer in CM 1: 6 complete all as specified and as directed.

M&L for non –skid ceramic coloured tiles 7-8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile over and including 15mm thick screed bed in CM 1: 6 complete all as specified and directed.

M & L for vitrified ceramic tiles of size 10 mm thick (light shade) (Square/rectangular) area of each tile not exceeding 0.36 sqm, in floors, set & jointed in neat cement slurry and pointed in coloured cement to match with colour of tile over and including 15mm screed bed in CM 1:6 complete all as specified and directed.

All as per item No 37 above but in skirting over & including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors complete all as specified and as directed.

M& L for machine cut kota stone slab in flooring 20-25mm thick laid over and including 15mm thick screed bed in CM 1:6 & cement mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and as directed.

All as per item no 35 above but in skirting including 10mm thick backing coat in CM (1:4 ) complete all as specified and directed.

M&L for cutting,grinding and polishing to surfaces of existing kota stone floor/skirting/dado with necessary grinding machine complete all as specified and directed.

M&L for chequered cement concrete tiles with grey cement and pigment of size 40cmX40cmX30mm thick (Glosy finish) ,set and jointed and pointed in neat cement slurry in floor etc over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M&L for machine pressed rubber moulded precast concrete interlocking paver block (glosy finish) any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment laid on 50 mm thick stone dust cushioning laid dry to the profile complete all as directed. Note: Sand cushioning shall be measured & paid seperately under relevant item.

M&L for Stone dust filling under floors 50mm thick including watering and consolidation.

Demolition of cement concrete (unreinforced) in ground floors and paving n exc. 15cm thickness (below or above ground level) complete.

Demolition of cement concrete exceeding 15cm in depth , of any description and in any position not otherwise specifically provided for ,including removal of concrete debries from site to a distance exceeding 500 metre all as specified and directed.

M&L for PCC (1:5:10) type E2 using 40mm graded stone aggregate as in foundations, filling and mass concrete, sunken floors complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C2 using 20mm graded stone aggregate as in plinth protection,finished the surface of concrete topping even and fair (without using extra cement) including making joint at every 3 m interval and at corner and filled with mixture of bitumen and sand , laid in alternate bays complete all as specified and directed.

M&L for 100 mm thick PCC 1:3:6 type C2 using 20mm graded stone aggregate as in plinth protection,finished the surface of concrete topping even and fair (without using extra cement) including making joint at every 3 m interval and at corner and filled with mixture of bitumen and sand , laid in alternate bays complete all as specified and directed.

M & L for plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate, 40mm thick as in floor, coping, finish the surfaces even and smooth with using extra cement complete as specified and directed.

M & L for provide PVC spout pipe of 25mm bore & 45cm length in sunken floor including cutting holes in brick walls built in cement mortor and making good the dismantled portion in PCC (1:2:4), type B1 using 20mm graded stone aggregate complete as directed and specified.

M & L for cutting holes in brick walls built in cement mortor Exc one one brick but not exc two bricks at the starting point of down take soil/waste pipe at any floor, fill the joint of down take pipe & trap with thick mortor in CM 1:3 and making good the dismantled portion in PCC (1:2:4), type B1 with using 20mm graded stone aggregate with wall finish at the disturbed portion of external surfaces complete as directed and specified.

M&L for provide water proofing treatment to sunken floor surfaces of RCC slab by the following specifications including taking down and cleaning of old surface as specified and directed :- (a) Provide PCC (1 : 1.5 : 3) type A0 using 12.5mm graded stone aggregate as in required slope, average thickness 50mm mixed with and including liquid water proofing compound PIDIPROOF LW manufactured by Dr FIXIT or other equivalent as approved by GE. (b) M&L rendering 15mm thick in CM 1:3 mixed with & including water proofing compound on sides of (Vertical surface) sunken floor slab. (c) Applying first coats of Dr fixit fastflex with a stiff nylon brush and leave 4 to 6 hours for dry. (d) Applying second coat of Dr fixit fastflex with a stiff nylon brush to the direction of 90 degree ( to the first coat) and leave 4 to 6 hours for dry. (e) Applying third coat of Dr fixit fastflex with a stiff nylon brush to the direction of 90 degree ( to the second coat) and leave 4 to 6 hours for dry. Note: (a)WPT Shall be done through approved applicator certified by Manufacturer (b)Liquid WPC shall be measured & paid seperately under relevant item.

S&F in repair vitreous china squatting pan `Orissa ' pattern of size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipes) including connection to trap and to flush pipe, lime concrete bedding, 'P' or 'S' trap complete all as specified and as directed.

Supply and fix in repair of wash hand basins, vitreous china,of size 550x400mm (flat back, or angle back type) including cutting for and pinning in ends of brackets or erecting stand exclusive of fixing of supply and waste pipe etc complete all as specified and directed.

S&F in repairs pedestal pattern vitreous china wash down water closet pan white colour including 110mm PVC (SWR) 'P' Trap including necessary jointing with run lead , front or back inlet,connection to drain (or out going pipe ) and to flushing pipe antisyphone pipe , plastic water closet seat cover white closed pattern with flat bottom and cover complete as specified and directed.

S&F in repair vitreous china uninal bowl, half stall coloured, with PTMT urinal spreader for fixing with 15 mm dia pipe, union for discharge pipe , providing and fixing plugs, bedding urinals against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long steel screws, pointing around the urinal back in white cement complete all as specified and directed.

S&F in repairs Chromium plated urinal spreader suitable for 15 mm dia pipe.

S&F in repairs mild steel chromium plated health fucet with 1m SS tube and hook all as complete specified and directed

S&F in repairs chromium plated jet for EWC with 1.00 m SS pipe including necessary GI fitting as required like tee,union,nipple etc all as specified and directed.

S&F in repairs fancy type chromium plated two way bib cock of 15mm bore ,screwed for iron pipe or brass ferrule etc complete all as specified .

M&L for repairing low level flushing cistern by adjustment of syphon washer,adjustment of handle and float valve as required and making flushing cistern functionable in all respects .

S & F in repair CP brass fancy type 15mm bore bib tap, screwed down , and screwed for iron pipe or for brass ferrule complete all as specified

S & F in repair 15 mm bore Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed all as specified

S&F in repair 15mm bore pillar taps, cast copper alloy with capstan heads, chromium plated,fancy type screwed down high pressure with or without lettered “HOT” or “COLD” with long screwed shanks and fly nutscomplete all as specified

S&F in repair 15mm bore, 450mm long, PVC connections with brass unions internally threaded both ends complete fixed to iron pipe at both ends complete all as specified

S & F in repair of CP fancy type stop valve ,cast copper alloy, screwed both ends for iron pipe or for union of 15mm bore complete all as specified

S& F in repairs CP Fancy type Angle coack one way, brass chromium plated, fixed to iron pipe or for unions 15mm bore complete all as specified

S&F in repair CP fancy type Stop Valve ( Concealed type),cast copper alloy, screwed both ends for iron pipe or for union of 15mm bore complete all as specified

S&F in repairs brass spindle for concealed stop cock 15/20mm bore size all as specified

S&F in repairs of CP brass fancy type shower rose 15mm dia with 125mm long CP nipple of approved quality complete all as specified

S&F in repairs 15mm dia brass CP Wall mixerfor hot & cold water, screwed down for iron pipe and fixed all as specified and directed.

S&F in repairs soap dish chromiumplated brass fixed with brass nuts all as specified

S& F in repai toilet paper holder brass chromium plated all as specified

S&F in repairs towel rail 600mm long 20mm dia brass chromium plated fixed with wooden guilties embedded in cement mortar (1:3) with MS screws etc complete all as specified

S&F in repair LDPE pipe 32mm bore fixed to wall / ceiling with bends / elbow complete all as specified.

S&F in repair stainles steel grating round type of 150mm size (Minimum weight 100 gms) complete all as specified

S&Fin repair PVC valveless, syphonic action type flushing cistern,low/high level white with inlet ball valve float and handle including brackets complete fixrd in repair capacity of flush 10 litres complete all as specified and directed.

S&F in repairs PVC flush pipe of 32mm dia with two numbers of check nuts for connecting low level flushing cisterb to EWC complete all as specified

S&F in repairs brass chromium plated waste coupling 32mm bore for WHB complete all as specified.

S&F in repairs brass chromium plated waste coupling 40mm bore for sink all as specified .

S&F in repair 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed.

S&F PVC waste pipe 32mm dia n.exc 1.50 m length fixed to any type of coupling complete all as specified

S&F PVC waste pipe 40mm bore for sink/urinal all as specified

M&L for stainless steel plate rack of size 900x750x250mm made out of 0.75mm thick stainless steel for kitchen of best quality with suitable hanging arrangement and fixed to wall complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs Stainless steel sink with drainage board , 1.00mm thick for kitchen, with plug, washers and wastes/coupling,waste pipe etc including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm with bowl size 410mmx 330mmx 160mm fixed complete all as specified and directed.

S&F in repair rotational moulded polythylene water storage tank of 500 litres capacity, double layered (cylindrical / vertical with closte top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing PTMT ball valve high pressure with polythene float and fly nut, 20mm bore complete

S&F in repair rotational moulded polythylene water storage tank of 1000 litres capacity, double layered (cylindrical / vertical with closte top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing PTMT ball valve high pressure with polythene float and fly nut, 20mm bore complete

S&F in repair rotational moulded polythylene water storage tank of 2000 litres capacity, double layered (cylindrical / vertical with closte top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing PTMT ball valve high pressure with polythene float and fly nut, 25mm bore complete

M&L for Cleaning and removing all dirts and scales from service water tanks and from mouth of circulating pipes etc capacity of tank exceeding 250 litres but not exceeding 500 litres complete all as specified and directed.

All as per item no 91 above but tank exceeding 500 litres but not exceeding 1000 litres capacity complete all as specified and directed.

All as per item no 91 above but tank exceeding 1000 litres but not exceeding 2000 litres capacity complete all as specified and directed.

S&F in repair PVC water storage tank cover of any size suitable for PVC water tank of any litres of capacity complete all as specified and directed.

S&F in repair of gun metal gate valves 20 mm with lever arm screwd both ends for iron pipes complete all as specified and directed.

S& F in repairs sheet glass shelf assembly, approved make, consisting of 5.5mm thick sheet glass shelf 60mm wide with chromium plated bracket guard and railing 500mm long complete all as specified & directed.

S&F in repair PVC (SWR) floor trap 75mm dia of outlet ,plain with grating including jointing with solvent cement complete all as specified

S&F in repair PVC (SWR) multi floor trap 75mm dia of outlet ,plain with grating including jointing with solvent cement complete all as specified

S&F in repair PVC body bath room cabinet with mirror fancy type made out of 5.5mm thick mirror of size 550 x 450mm complete, Model No 555 of PRAYAG or other equivalent as approved by GE complete all as specified and directed.

S&F in repair plastic water closet seat cover white closed pattern with flat bottom and cover with mild steel/ chromium plated or aluminised hinging device complete all as specified

S&F in repair 110mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid on wall / floor with clip complete all as specified

S&F in repair of 75mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid on wall / floor with clip complete all as specified

S&F PVC (SWR) branch pice, single (Single Y) equal or unequal 110mm size

S&F PVC ( SWR) bends any radius bore of 110 mm

S&F PVC ( SWR) bends any radius bore of 75 mm

S&F in repairs 25mm dia stainless steel curtain rod as all as specified and directed.

S&F in repairs stainless steel decoarative brackets suitable for curtain rod of 25mm dia complete all specified and approved by GE .

Taking up or down steel tubing 15mm bore & connections and S&F GI tubing medium grade with all fittings & fixed complete to walls /ceiling or laid in floors complete all as specified and directed.

Taking up or down steel tubing 20mm bore & connections and S&F GI tubing medium grade with all fittings & fixed complete to walls /ceiling or laid in floors complete all as specified and directed.

Taking down chowkhats or frames with shutter (without taking off shutters from the frame) area n. exc 1.5 sqm each complete all as specified and as directed.

S&F factory made steel window with side hung shutter including projecting type hinges with steel handle, peg stay complete with glazing bars dovetailed or welded, etc complete all as specified

S&F factory made steel Window , with side hung shutter including projecting hinges with steel handle, stay complete without glazing bar and guard bar dovetailed or welded complete all as specified.

S&F factory made steel ventilator fixed type with glazing bar complete all as specified and as directed

S&F PVC door frames of sizes 50 x 47 mm made out of 5 mm prelam PVC sheet reinforced with MS Square tube in opening of suitable size complete all as specified and directed.

S&F Factory made (Prelam on both sides) solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall covered with heat moulded prelam PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for styles and prelam PVC sheets for top rail, lock rail and bottom rail in either side and as gap insert for top rail and bottom rail pannelling of prelam PVC sheet to be filled in the MS welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together wiht solvent and fixing in the frame at site as per specification and drawing complete all as specified and directed.

Taking down chowkhats or frames with shutter (with out taking off shutters from the frame) area exc 1.5 but nexc 4.0 sqm each complete all as specified and as directed.

Taking down shutters of any description n.exc 1.0 sqm each complete all as specified and as directed.

Taking down shutters of any description exc 1.0 sqm but n.exc 2.0 Sqm each complete all as specified and as directed.

S&F 35mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; size of members of shutters as specified in SSR Part – I, Section – 8, clause 8.24(a) ; supplied and fitted to chowkats all as specified and directed.

S&F 30mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; size of members of shutters as specified in SSR Part – I, Section – 8, clause 8.24(a) ; supplied and fitted to chowkats all as specified and directed.

S&F second class HardWood shutters 35mm thick, plain framed panelled shutter factory made (two panel) with lock rail & panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS:1003 complete all as specified and directed.

S&F pressed steel frame of size 105X60mm for doors with one or more rebates including necessary fixing lugs,hinges,lock strike plate.etc completet all as specified and directed.

S&F pressed steel frame of size 165X60mm for doors with one or more rebates including necessary fixing lugs,hinges,lock strike plate.etc completet all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire stapples complete all as specified and directed.

S & F in repair galvanised MS wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staples including takingout old wire mesh from steel window and fixing old steel flats and nut complete all as specified and directed.

Haking out old brocken glass pan of any size ( upto G+3 Storied building) thickness,size,quality or description) from wooden frames or stone,concrete or brick ,glazed with putty or fixed with beads all as specified and directed.Note: Glass repairing work shall be carried out upto G+3 Storied building .

S & F figured glass 3mm thick pin head type and glazing with oil putty and securing with glazing pins not exceeding 0.50 Sqm in each pan complete all as specified and directed by Engineer - in - Charge .

S&F sheet glass 3.0 mm thick ordinary quality and glazing with oil putty, in squares n. exc 0.5 Sqm in each pan incl hacking out complete all as specified and directed.Note: Glass repairing work shall be carried out upto G+3 Storied building

Dismantling wrought iron or mild steel work of any description as provided for Roof trusses, trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) complete all as specified and directed.

S&F Mild Steel work as in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness including nainital or similar pattern roof covering all as specified

S & F Pre- painted galvatume aluminum zinc coating GI based corrugated (profile pattern) steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling of Asbestos cement (corrugated, semicorrugated) sheets in roof coverings complete all as specified and as directed.

S&F 6mm thick asbestos cement corrugated or semi corrugated sheets in roofs walls etc fixed with L-type or J-type or cranked hook bolts all as specified and directed

S&F Asbestos cement serrated ridge for corrugated or semicorrugated sheets fixed with L-type or J-type or cranked hook bolts all as specified and directed

S&F 100mm long butt hinges aluminium alloy with galvanised mild steel hinge pin,anodised and fixed B-22

S&F in repairs 100mm long butt hinges aluminium alloy with galvanised mild steel hinge pin,anodised and fixed B-22

S&F in repair 100mm long butt hinges medium weight cold rolled mild steel

S&F in repair 75mm long butt hinges medium weight cold rolled mild steel

S&F 200 mm long aluminium anodized barrel tower bolts of extruded section

S&F in repairs 200 mm long Aluminium anodizes barrel tower bolts of extruded section

S&F in repairs 150 mm long Aluminium anodizes barrel tower bolts of extruded section

S&F 150 mm size aluminium anodized handle complete all as specified

S&F in repiars 150 mm size aluminium anodized handle complete all as specified

S&F in repairs mild steel ordinary rat tail rod pattern spring of 300mm size including roller & roller plate complete all as specified

S&F in repairs aluminium floor door stopper double legged length 140mm with hard drawn steel spring fitted in floor complete all as specified and directed.

S&F in repair Aluminum plate type II of size 200mm , hook and eyes all as specified and directed.

S&F in repair 40mm wide upto 5mm thick rubber beading fixed to door shutter with nails all as specified and directed

M&L for preparation of new wooden surface of any description over 10cm in girth or width and applying two coats of synthetic enamel paint over a coat of primer complete all as specified

M&L for painting with two coats of synthetic enamel paint to steel surfaces of any description over 10cm in width or girth over a coat of red oxide primer including preparation of steel surfaces complete all as specified and directed.

S&F in repair 18/19mm thick block boards grade 2 quality, interior grade, commercial type as in shelves and partitions of cup boards fixed with screws to under frame work inculding 6 mm thick teak wood lipping edging on all sides complete all as specified and directed.

S&F in repair 19mm thick priliminated particle board both sides with decorative choice including necessary second class hard wood 6mm edging for cup board all as specified and directed

S & F second class hard wood plain, solid straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and as directed.

S&F Continuos ( piano) hinges mild steel, bright finish or electro galvanized 30mm width flap ( When open) type all as specified and directed.

M&L for welding in repairs not exceeding 2.5 cm in length to the thickness of metal to be welded 9mm but n.exc 20mm complete all as specified and as directed.

M&L for preparation of surfaces of bldg No plate / tab of any size and apply one coat of synthetic enamel paint and writing letters or figures (Block, Roamn, Italic or Indian) of not less than 50 mm height and not less than15mm width incl, stops, commas, lines etc complete all as specified and directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillet complete.

S&F false ceiling at all heights with integral densified calsium silicate reinforced with fibre and natural filler false ceilling tiles of size 595X595mm of approved texture, design and pattern pinhole 8mmthick semi perforated square edge tile having NRC ( noise reduction cogfficient ) of 0.50 (minimum) Light refluctance of 85% (minimum) Non combustable as per BS : 476 (PART-4) fire performance as per BS : 476 ( PART 6&7) humidity resistence of 100% thermal conductivity <0.043 W/m K as per ASTM 518:1991, intrue horizontal level suspended on interlocking metal powder coated T-grid of hot dipped galvanized iron section on proffile,stitched duoble webbed white with 1mm reveal proffile ( White/black) comprising of main-T runner of size 15X 32mm of lenght 3000mm, cross-T of size 15 X 32 mm of lengh 1200mm and secondary intermediate cross-T of size 15 X32mm of lengh 600mm to form grid module of size 600X600mm,from ceiling using galvanized mild steel item, 8mm outer daimeter M-6 dash fasteners, 6mm dia threaded hanger rod and L- shape leval adjuster of size 85X25X2mm Galvanized iron perimeter wall angle of size 19 X 19mm of lenght 3000mm to be fixed on periphery wall /Partition with the help of plastic rawl plugs at 450mm centre and 40mm long dry wall SS screws.NOTE: The work shall be carried out as per specifications and , drawing and all as per direction of Engineer-in-Charge.

Dismantling of timber boarding of any description, fixed in any position with nails all as specified and directed.

S&F 4mm thick non asbestos cement plain building boards, fixed to wooden frame work with screws including preparing of surfaces and applying two coats of wite wash in ceiling complete all as specified and directed.

M&L for servicing steel rolling shutter of any description of size n.exc 10sqm by greasing movable parts of steel rolling shutters for smooth functioning , adjusting of springs, guides,locking plates etc and making rolling shutter functionable to the entire satisfaction of Engineer-in-Charge complete all as specified and directed.

S&F in repair ball bearing for steel rolling shutters all as specified and directed

Demolition of precast cement concrete jallies as in boundary wall including coping beam and removing all debries from premises all as specified and directed

S&F Precast cement concrete jallies 40mm thick with cement concrete 1:2:4 type B0 using 12.50mm graded aggregate including all moulding and set in CM 1:4 complete all as specified and directed

M&L for reinforeced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in copin,beams etc complete all as specified and directed.Note:Reinforcement shall be measured and paid separately under relevant item.

M&L for formwork to sides and soffits of coping, beam etc fair finished complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over,cut to length,bent to shape required,including cranking,bending spirally for hooping ends and binding with and including mild steel TMT (annealed) not less than 0.9mm dia or securing with clips all as specified and diretced.

M&L for Mild steel TMT bars 8mm dia and over,cut to length,bent to shape required,including cranking,bending spirally for hooping ends and binding with and including mild steel TMT (annealed) not less than 0.9mm dia or securing with clips in stirrups all as specified and diretced.

Chitragupta Construction