REPAIR AND REPLACEMENT OF INTERNAL WATER SUPPLY SANITARY FITTING, PLUMBING WORK ND ALLIED MISC WORK UNDER GE 865 EWS

Amount

Demolition of cement concrete in ground floor and pavings n.exc 15cm thick below or above ground level.

M&L for 75mm thick PCC type C-2 , I:3:6 using 40mm graded crushed stone aggregate as in sub base for laying floor finishes.

M&L for 7mm thick non skid coloured ceramic tiles (area of each tile exc 0.06and nexc 0.11 sqm) etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments.incl 15mm thl creed bed CM 1:4.

M&L for 7mm thick non skid coloured ceramic tiles (area of each tile exc 0.18and nexc 0.38 sqm) etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments incl 15mm thl creed bed CM 1:4.

Vitrified ceramic tiles 10mm thick light colour (square/rectangular) area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thk screed bed CM 1:4.

Dismantling floor , hearth or wall tiling including cement mortar bedding (but not backing) ,removing servicable one to store and rubbish off the premises

M&L for 75mm plian cement concrete type B-2 1:2:4 , using 40mm graded curshed stone aggregate as in flooring without using extra cement.

M&L for 40mm plian cement concrete type B-1 1:2:4 , using 20mm graded curshed stone aggregate as in flooring without using extra cement.

M&L for (350mmx250mmx7mm/450mmx350mmx 7mm thick ) coloured ceramic tiles set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments.(Note: Any disturbed surfaces shall be matched w/o any extra cost to the govt) incl 10mm thck screed bed below tile for dado/skirting CM 1:4.

M&L for 25mm thick PCC type B-0 using 20mm graded crushed stone aggregate as in sub base for laying floor finishes.

M & L for Chequered cement concrete tiles, machine pressed, factory made of size 300mmx300mmx20mm thick, set, jointed and pointed in neat cement slurry, with grey cement and no pigment, laid in floors, over and including 20mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

Demolition of brick or stone masonary including all necessary arches, pillars, quions etc built in cement mortar.

M&L for precast cement concrete block masonary 1:3:6 type C-1 (using crushed stone 20mm graded aggregate) with solid blocks exc 10 cm in width ,set and jointed in cement martar 1:6

Taking down cement plaster on brick/PCC block or conc surfaces including racking out joints hacking for key, scrubbing down with water etc.

M&L for 15mm thick rendering on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1:4

M&L for 15mm thick rendering on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1:6

M&L for two coats cement base paint on newly plastered surfaces including preparation of surfaces.

Disconnecting existing tanks, setting aside (or lowering if required)for repairs , cleaning ete. And hoisting if requeired reconnecting and refixing in position of capacity n .execeeding 250 ltrs and removing to stores, all as specified.

Disconnecting existing tanks, setting aside (or lowering if required)for repairs , cleaning ete. And hoisting if requeired reconnecting and refixing in position of capacity execeeding 250 ltrs and not exceeding 500 litres and removing to stores, all as specified.

Disconnecting existing tanks, setting aside (or lowering if required)for repairs , cleaning ete. And hoisting if requeired reconnecting and refixing in position of capacity execeeding 500 ltrs and not exceeding 1000 litres and removing to stores, all as specified.

Rotational moulded polyethylene water storage tank (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 250 litres including all accessories, all as specified.

Rotational moulded polyethylene water storage tank (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 500 litres including all accessories, all as specified.

Rotational moulded polyethylene water storage tank (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 1000 litres including all accessories, all as specified.

Rottational moulded polyethylene puf insulated water storage tank (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 250 litres including all accessories, all as specified.

Rottational moulded polyethylene puf insulated water storage tank (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 500 litres including all accessories, all as specified.

Cleaning and removing all scale and dirt etc. from mouths of circulating pipes etc, capacity of tank exceeding 250 ltrs and not exceeding 500 litres and refixing in the same position incl taking down.

Taking up or down steel tubing 15mm bore including cleaning for refixing or removal to store.

M&L for 15mm bore medium grade galvanished iron water tubing with all fittings and fixed complete to walls or laid in trenches.

All as per item No 28 but fixing only

Taking up or down steel tubing 20mm bore including cleaning for refixing or removal to store.

M&L for 20 mm bore medium grade galvanished iron water tubing with all fittings and fixed complete to walls or laid in trenches.

All as per item No 31 but fixing only

Taking up or down steel tubing 25mm bore including cleaning for refixing or removal to store.

M&L for 25 mm bore medium grade galvanished iron water tubing with all fittings and fixed complete to walls or laid in trenches.

All as per item No 34 but fixing only

S&F 15mm bore 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc.

S&F 20mm bore 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc.

S&F 25mm bore 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass treaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc.

M&L for making connection of PP_R distribution branxh with PP-R main of 16 to 40 mm bore pipes of following sizes by providing and fixing tee including cutting and making fusion joint etc.

Providing 100mm thick Insulation of water tank 500 ltr which includes of following items:- (i) Nitrile sheet 19mm (ii) Rock wool (iii) Wire mash (iv) Polythene (v) Cello tape (vi) Aluminium Sheet 28 gauge

Providing 50mm thick insulation of water pipe 20mm bore line which includes of the following:- (i) Export quality heat tape (ii) Aluminum tape (iii) K Flex 19mm (iv) Rock wool (v) Wire Mesh (vi) Ploythene (vii) Cello tape (Viii) Aluminium Sheet 28 gauge

S&F PPR ball valve conforming to ISO 2000 screw down end for PPR pipe or for union and fixed completey as specified for the size 25mm bore.

S&F PPR ball valve conforming to ISO 2000 screw down end for PPR pipe or for union and fixed completey as specified for the size 20mm bore Make SFMC/prince

S&F PP-R Gate valve 20mm bore outer dia (brass insert) as per requirement of the site

S&F PP-R Gate valve 25mm bore outer dia (brass insert) as per requirement of the site

S&F PPR 15 mm bore socket in new or old position

S&F PPR 15 mm bore Tee in new or old position

S&F PPR 15 mm bore elbow/bend in new or old position

S&F PPR 25 mm bore socket in new or old position

S&F PPR 25 mm bore Tee in new or old position

S&F PPR 25 mm bore elbow/bend in new or old position

S&F PPR 20 mm bore socket in new or old position

S&F PPR 20 mm bore Tee in new or old position

S&F PPR 20 mm bore bend in new or old position

M&L for 25 mm bore cutting existing steel tubing for alteration or addition (Each cut to be measured seperately)

M&L for 20 mm bore cutting existing steel tubing for alteration or addition (Each cut to be measured seperately)

S&F in repairs 15 mm bore GI socket medium weight.

S&F in repairs 15 mm bore GI nipple 150 mm long medium weight.

S&F in repairs 15 mm bore GI nipple 100 mm long medium weight.

S&F in repairs 15 mm bore GI nipple 200 mm long medium weight.

S&F in repairs 15 mm bore GI union medium weight.

S&F in repairs 15 mm bore GI socket medium weight.

S&F in repairs 15 mm bore GI Tee medium weight.

S&F in repairs 15 mm bore GI elbow medium weight.

Long nipple 15 mm bore

S&F in repairs 20 mm bore GI socket medium weight.

S&F in repairs 20 mm bore GI nipple 150 mm long medium weight.

S&F in repairs 20 mm bore GI nipple 100 mm long medium weight.

S&F in repairs 20 mm bore GI union medium weight.

S&F in repairs 20 mm bore GI socket medium weight.

S&F in repairs 20 mm bore GI Tee medium weight.

S&F in repairs 20 mm bore GI elbow medium weight.

Long nipple 20 mm bore for water tanks

S&F PVC waste pipe 32mm bore with cup and washers complete on new or old locations.

Supply only CP flush pipe 32mm bore for low level cistern.

S&F half stall urinal flat back (large) 635x395x420 white colour . Make CERA CAT No: 5001/Jaguar

S&F urinal half stall type wihte including CP spreader, wastepipe.

S&F self closing angle cock pressmatic for urinal with flange and 200 mm connecting pipe and spreader.Make: Jaguar

S&F 15mm bore bib taps cast copper alloy with capstan head screwed down screwed for iron pipe or brass ferrule. (Minm wt 350 Gms)

S&F 15mm bore bib taps fancey type with capstan head chromium plated screwed down screwed for iron pipe or brass ferrule. (Minm wt 350 Gms)

S&F 15mm bore pillar tap cast copper alloy with capstan head chromium plated screwed down under high pressure with or without lettered hot or cold with long shank and fly nuts screwed for iron pipe.

S&F 15mm bore stop cock cast copper alloy screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule.

S&F 15mm bore brass valve high pressure with polythene float and fly nuts complete screwed for iron pipe or brass ferrule.

S&F 15mm bore stop cock chromium plated screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule .

S&F 20 mm bore stop cockcast copper alloy screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule .

S&F in repair Brass CP mixer for mixing Hot & clod water screwed down for iorn pipe and fixed in reapair 15 mm bore dia Make: Cera//Jaguar

S&F in repair Gun metal globe or gate valve 15 mm bore with iron wheel head, screwed both ends for iorn pipe and

S&F in repair Gun metal globe or gate valve 20 mm bore with iron wheel head, screwed both ends for iorn pipe and

S&F Grating doom 125 mm with waste hole of PTMT

S&F in repair Brass chromium plated shower rose 125 mm size Make -Jaguar

S&F bib taps standard of PTMT any colour screwed for iron pipe and fixed (Minm wt 90 gms)

S&F 15 to 20 mm bore PTMT pillar tap of any colour screwed for iron pipe or for iro pipe and fixed (Min wt 110 gms)

S&F 15 mm bore stop valve of PTMT any colour high pressure screwed for iron pipe and fixed

S&F Sinks stainless steel with drainage board made of 1.0 mm thick kitchen or laboratory with plugs, washers and wastes; including fixing contilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mm x 330mm x 160mm, all as specified.

S&F stainless steel plate rack of size 600x900mm fixed with screws

S&F shelf of PTMT with and including chromium plated brass screws and wooden or plastic cleats.

S&F chromium plated soap dish incl chromium plated screws and PVC rowel plugs.

S&F Viterous china wash down water closet pan pan (pedestal pattern ), white (excluding flushing cistern , flush pipe.(Make: CERA,Perryware,Hindware, Jaguar)

S&F pvc white seat cover incl all necessary hinges(Make: CERA,Perryware,Hindware, Jaguar)

S&F viterous china wash hand basin flat back size 580x450mm excluding traps, waste , chain , plug and porcelain stopper incl brackets

S&F CP waste cuppling32mm dia (Half or ful threaded) including waste pipe .(Make: CERA,Perryware,Hindware, Jaguar)

25. S&F in repair vitreous china white squating pan orissa pattern size 580 mm x 440 mm white with integral foot rests any pattern (excluding flushing cistern and flush pipe), complete incl. provision of lime concrete bedding, making good to floors all as specified and directed.

S&F PVC flushing cistern 10 ltr capacity , syphonic action type flushing cistern low level with inlet ball valve ,float and handle including connection to pipe but fixed in repair. (Make: CERA,Perryware,Hindware, Jaguar)

S&F PVC connection 15mm bore with ptmt nuts of length 450mm

S&F water closet wall hung / padestal pattern coloured (as approved by Engr-in-Charge) Make: CERA CAT No 2035,2115,2315,2235/ (CLAIR , single piece suite) /Jaguar incl seat cover

S&F 15mm bore centre hole basin mixer with round sport w/o pop up waste system incl 450mm long braided hoses and brass nuts Make: CERA CAT PART No. CS 915

S&F 15mm bore angular stop cock with wall flange Make: CERA CAT PART No.CS 908/Jaguar.

S&F chromium plated toilet paper holder make: Jaguar.

S&F brass chromium plated towel ring fancey type make CERA cat part No.CA 305/Jaguar.

S&F soap dish Make CERA Cat No CA 206/Jaguar

S&F chromium plated double coat hook makeCERA Cat part no: CA 308/Jaguar.

S&F Hand shower ( health faucet ) brass body with 8mm dia 1 meter long SS braided flexible tube with wall hook. Make :/Jaguar

S&F32 mm size waste coupling size full thread:CERA CAT NO CM 103/Jaguar.

S&F chromium plated towel rack 24" . Make CERA Cat Part No CA 301/Jaguar.

S&F Liquid soap dispensar Make : CERA CAT NO CA 211/Jaguar.

S&F Tumbler holder Make CERA CAT NO : CA 207/Jaguar.

S&F 15 mm bore wall mixer with telephone shower arrangement and inc tele phonic shower Make :CERA/Jaguar.

S&f 110mm bore PVC (SWR) pipe single socketed , in any length with rubber joints fixed to walls

S&f 110mm bore PVC (SWR) pipe bends any radius

S&f 75mm bore PVC (SWR) pipe single socketed , in any length with rubber joints fixed to walls

S&f 75mm bore PVC (SWR) pipe bends any radius

S&F 75 mm bore PVC (SWR)) floor traps plian with grating incl jointing with solvent cement.

S&F 75mm bore cast iron floor trap with grating including jointing to waster pipe fixed in cement concrete type B-1 1:2:4

S&F 75mm bore sand cast iron waste pipe any length with or without ears laid in floor.

S&F 100mm bore sand cast iron waste pipe any length with or without ears fixed to walls

S&F100mm bore sand cast iron waste pipe any length with or without ears laid in floor.

S&F 75mm bore sand cast iron waste pipe any length with or without ears fixed to walls

S&F sand cast iron bend (any radius) 100mm bore dimnishing pieces or tapers (larger bore measured ) fitted with oval acess doors

All as pet item No 144 but 100m bore with ducks foot rest or heel rest.

S&F sand cast iron bend (any radius) 75mm bore dimnishing pieces or tapers (larger bore measured ) fitted with oval acess doors

M&L for run lead joint to 100mm bore sand cast iron pipe

M&L for run lead joint to 75mm bore sand cast iron pipe

S&F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to walls for 50mm bore pipe

S&F cast iron cowl 75mm bore

S&F 100mm bore CI sand cast iron branch piece single (Equal or un equal) oridinary or inverted with parallel branches

S&F for framed work as in grills gratings etc with ends of ends of bars shouldered or forged in to spikes etc conforming to Fe 290.Gde 165

M&L For 15 mm bore lagging to pipes used in internal water supply or plumbing all round with 40 mm min thick bonded glass/mineral snap wool preformed pipe section of density 144 kg/cum conforming to IS 9842 ,the work includes chicken wiremesh netting 25 gauge ,20 mm mesh ,leaping with POP and finally wrapping with aluminum foil 0.01 mm thick.(Note: whole stage has to be app by Eng-in-charge)

M&L For 20 mm bore lagging to pipes used in internal water supply or plumbing all round with 40 mm min thick bonded mineral snap wool preformed pipe section of density 144 kg/cum conforming to IS 9842 ,the work includes chicken wiremesh netting 25 gauge ,20 mm mesh ,leaping with POP and finally wrapping with aluminum foil 0.01 mm thick.(Note: whole stage has to be app by Eng-in-charge)

S&F in repairs viterous china ware wash hand basin oval type of size 570x450mm

M/S Web Company

M/S SHABIR AHMAD SHAH AND CO

M/S SUMEET TRADING CORP

RISING SUN ENGG WORKS

national engineering

M/S SHAMSHER ALI SUFI

M/S LIBE & CO