Renovation of Entrance lobby, CE cabin, staircase and VIP Toilets including Electrical, HVAC, UPS, FAS, Networking related works in REPF office Building at BRIT Vashi Complex, Vashi, Navi Mumbai.

Amount

Section- A: (General Civil works ) Providing and fixing 15-17 mm thick gang saw cut mirror polished Granite (premoulded and prepolished) machine cut Granite (Moon white shade or as approved) for flooring / skirting in lobby, passage, staircase (Tread and Riser), kitchen platforms, vanitiy counters, Wash basin Counters, Door Frames, window sills, facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (using coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing the edges to give high gloss finish etc. complete at all levels

Providing and fixing Glazed VITRIFIED floor tiles of approved make in different sizes conforming to IS 15622 in all colours and shades in Glossy or Matt or satin finish of size 290 X 1800 mm laid over a bed of minimum 20 mm thick bed of cement mortar 1:4 (using Crushed sand) andjointing with grey cement slurry including grouting with the joints with white cement based Tile Grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Engineer-in-charge.

Providing, applying Wall painting Two coats with Premium plastic emulsion Paint of (Asian or Equivalent approved brand and manufacturer) to give an even shade over a coat of Cement Primer.including preparation of the surfaces, scaffolding complete as per specifications and as directed by the Project Engineer.

Providing and applying white cement based wall putty ( Birla wall Care or approved equivalent) over concrete or Plastered surface minimum 3 mm and up to 6 mm thick to get uniform surface free from undulation including cleaning complete all as directed at site.

Providing, applying Wall painting Two coats with Lustre paint (Asian or Equivalent approved brand and manufacturer) to give an even shade over a coat of Cement Primer.including preparation of the surfaces, scaffolding complete as per specifications and as directed by the Project Engineer.

Providing and Painting two coats of synthetic enamel paint on Steel Surfaces of approved brand and manufacture to give an evenshade with out primer coat. including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

Providing structural Repairs in Old Damaged concrete structures / surfaces with approved Polymer with following operations 1) Removal of loose/Spaled or damaged concrete by chipping and cleaning the concrete suface and Reinforcement steel with wire brush and with water jet. 2) Cleaning the Re bars with Acetone for complete Rust removal and washing with water jet to make the surface free from Acid content. 3) Applying Protective Coat / bond coat using Polymer and Cement in the proportion of 1; 1.5 ( 1 part of polymer and 1.5 parts of cement in Synthetic enamal paint like consistancy with brush 4) Reinstate the area with polymer modified mortar in layers of maximum 20 mm with the proportion of Cement 50 Kg : Washed and dried river sand 87.50 kg ; Silica sand 37.50 Kg. mixed with 10 litres of Polymer ( or 1 Kg cement : 1.75 kg Washed and dried river sand ; 0.75 Kg Silica Sand : 200 ml polymer). 5) If thickness of repair exceeds 20mm , after every 20 mm thick repair bond coat as per 2 above to be applied and further thick of repair to be continued for each layer. This work is inclusive of all materials, labour, complete all as directed at site .(Polymer "ROFFE/BASF/FOSROC" or approved equivalent make suitable for Structural repair shall be used )

Providing 15 mm thick plastering using Ready mix internal plastering compound of approved make for internal faces of brickwork / concrete surfaces including preparation of the surface, curing, cleaning, scaffolding complete all as per specifications and as directed at site by the Engineer-in-charge

Providing 20 mm thick plastering using Ready mix external plastering compound of approved make for external faces of brickwork / concrete surfaces including preparation of the surface, curing, cleaning scaffolding up to 10 metres height complete.all as per specifications including forming drip moulds wherever necessary and as directed by the Engineer-in-charge

Providing and laying in position cement concrete of 1:2:4 (1 cement, 2 crushed sand, 4 graded stone aggregate of nominal size 20 mm) including consolidation, finishing, curing etc. complete as per specification and drawings but excluding the cost of Formwork shuttering, centering and steel reinforcement at all Levels

Providing and Laying Autoclaved Aerated cement block masonry of approved make with specified thick AAC Blocks in Super structure above plinth level up to 20 m height in cement mortar 1:4 (using crushed sand). The rate shall also include providing and placing in position 2 nos of 8 mm dia bars at every third course of the masonry work

Providing Reinforcement for reinforced cement concrete at all levels including supplying, preparation of bar bending schedules,cutting, bending, transporting, fixing, tieing in position with 1.6 mm dia soft drawn annealed binding wire all labour charges, cost of cover blocks in specified grade of concrete etc. complete including cost of binding wire as per specifications and drawings. Note: Cover blocks shall be of same grade of concrete Steel Supplied by the Contractor Using TMT bars of specified grades all dia bars. TMT bars to be supplied by the contractor manufactured by approved brands of BARC only Confirming to IS:1786

Dismantling plain cement concrete manually / by mechanical means carefully without damaging adjacent structures including disposal of debris within 200 m lead as per direction of Engineer-in-charge

Dismantling brick work in Cement mortar carefully without damaging adjacent structures including stacking of materials and dispoal of unserviceable materials within 100 m lead as per direction of Engineer-in-charge

Dismantling old plaster / skirting carefully , raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 100 m lead

Dismantling of RCC works including Cutting and stacking of steel reinforcement bars and disposal of unserviceable materials within 100 m lead as per direction of Engineer-in-charge

Dismantling doors, windows and clear storey openings (steel / wood) shutter including chowkhats, architraves, holdfasts etc. complete and stacking within 100 m lead (full windows) Of area 3.00 Sq.M and below

Taking out doors, windlows and clear storey openings (steel / wood) shutter including stacking within 100 m lead (only shutters) Of area beyond 3.00 Sq.M

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 100 m lead For thickness of tiles above 10 mm and up to 25 mm

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 100 m lead For thickness of tiles above 25 mm and up to 40 mm

Dismantling Aluminium / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplaus material and stacking of serviceable materials within 100 m lead as directed by the Engineer-in-charge

Removing existing G.I. duct of air conditioning system of cross section upto 2-4 m² carefully including removal of structural steel members, chicken wire mesh, fibre glass wool and cement plaster thermocole complete all as direted by Engineer-in-charge. The rates are inclusive removing of supporting rods, angle bracket etc. stacking the same with in 50 m lead as per direction of Engineer-in-Charge

FIXED FURNITURE WORK Note : - Following specifications holds good for the line items falling under this sections. The vendor shall quote rate inclusive of all the below mentioned specifications for the line items. Rates quoted for the partitions shall be inclusive of making cutouts for Electrical & HVAC Ducts, dampers outlets and for making provisions for passing conduits through the framework. Rates quoted for partitions shall be inclusive of additional vertical or horizontal frame members as required for skirting, band, fixing of electrical Boxes etc. apart from the regular framework members as specified Wood preservative for the Framework to be applied on all the internal surface. if any ply has been used. All gypsum partitions should be as per manufacturers specifications, and also refer all detail drawings of Gypsum partitions The cost of items under this section shall be inclusive of all the adhesives, hardware, fixtures, fittings etc. required for errecting the partitions/ paneling / cladding etc. The cost shall be inclusive of making 6 mm grooves as per design requirements. The Wooden frame work shall be treated with black Japan and the finished sizes shall be 2" X 2" or 2" X 1.5" thk or as specified in the items below. The Veneer / laminate shall be of 1st quality, approved make, shade & color by the Architects. Veneer shall be of 4 mm thkness and Laminate shall be of 1.0 mm thkness or otherwise specified.all timber members to be treated with pre-approved anti termite solution. Cost should be incusive of above ceiling framework required for fixing glass partition, doors & Frames DETAIL DRAWINGS & LAYOUT SHALL BE READ ALONG WITH THE BOQ. FRAMEWORK Providing & Fixing metal framework for partition / cladding / panelling fixed with all the necessary supports with true floor & ceiling for sturdy finish , 40mm thk Acoustic 6 rockwool slab of density 48kg/m³ shall be placed in metal framework. Rockwool holding clip should be used to hold rockwool slab in its position. Rockwool to be fully covered with fiber paper

48mm G.I. Framework ; Providing & Fixing of 48x0.5mm G.I. C-stud placed at 610mm c/c in 50x0.5mm G.I. floor and ceiling channel. and on the other side Floor & Ceiling channel is anchored to the floor & True ceiling using Rawl plug Ø8x45mm zinc coated with pull out Load-6.8kN for M30 concrete grade at 600mm c/c in centerline. A G.I. Noggin channel of 48x0.5mm width has to be provided at the horizontal joints of the two boards. Mode of measurements:- Sq. Mt. area.Front elevation only,No wastage to be added.

12mm thk commercial plywood ; Providing & Fixing 12mm thk commerical ply over existing framework fixed with screws, hardwares, adhesive etc. at minimum spacing of 600mm vertically & horizontally finished with minimum jointing groves visible. Mode of measurements:- Sq. Mt. area.Front elevation only,No wastage to be added.

1mm thk Laminate; Providing & Fixing 1mm thk Laminate of approved shade, pattern, color cladded over existing ply panelling with necessary & approved hardware & adhesive as per requirement in line level, free from buldge , matching grove and patterns complete as per detail Specification & Approved drawing Mode of measurements:- Sq. Mt. area.Front elevation only,No wastage to be added.

Natural stone Cladding; Providing and fixing Natural stone caldding made out of 4 mm thk of approved make, color & shade and fixed on existing partition framework with 12 mm thk comm. ply back. The stone shall be fixed using Adhesive. The treatment from top & backside of slab shall be considered in the cost. all complete as per architects instructions. Mode of measurements:- Front Elevation, No wastage to be added

MDF Fluted Panelling;Providing & fixing 12 mm thick MDF Fluted panelling of approved shade / pattern / colour fixed on existing finished surface using adhesive & necessary hardware, etc as per detailed drawing. Mode of measurements:- Sq. Mt. area. Front Elevation, one side only.No wastage to be added.

Junction Box Cover with framework;Providing and fixing junction box cover in hard flooring of size from 600 mm X 600 mm, 450 mm X 450 mm, 300 mm X 300 mm, 150 mm X 150 mm made of 19 mm thk commercial plywood with necessary teak wood framework to prepare a leveled surface. Mode of measurements:- Numbers no wastage to be added

Trap Door in laminate finish.; Providing and Fixing Trap door made of 19mm thk marine ply with 1.0mm thk laminate on both sides with 50 mm X 35 mm thk ply frame work @ c/c distance of 450 mm or as per site conditions, with required hardware fitting and Allen key locking arrangement as directed by the Architect. Mode of measurements:- Sq.mtr. area. Surface, one side only no wastage to be added

Gypsum Trap Door; Providing and Fixing gypsum trap made out of 12.5mm gypsum board with 15mm wide aluminium T profile fixed to the existing gypsum ceiling. Mode of Measurment-Sq.mtr area.As laid ,No wastage to be added.

PVC corner guards;Providing and fixing PVC Mouded fixed with necessary hardware. Mode of measurements:- Running meter Length, No wastage to be added.

Texture Paint ;Providing and applying Texture paint of approved shade & color over 2 coats of primer of approved shade & 2 coats of wall putty, complete as per manufacturers specifications, drawing & as directed by the Engineer-in-charge. Mode of Measurement:- As laid Sq. Ft / Sq. Mt. area. No wastage to be added.

Wall Paper; Providing and fixing Wall Paper of approved shade with recommended LOW VOC Adhesive of approved make. Cost to include preparation on the punned surface for receiving the wall paper as per the manufacturer specification.

8MM THIK -MDF;Providing & Fixing 1mm thik laminated panel made out of 8mm thk CNC cut exterior grade MDF with 1mm thk laminate with screws, hardwares, adhesive etc. as per detailed drawing. Mode of measurements:- Sq. Mt. area.Front elevation only,No wastage to be added.

Decorative screen

Pelmets & Coves

Pelmet In Laminate Finish;Providing and fixing pelmets of size 150 mm x 150 mm as per site conditions with verticals made of 19 mm thk prelam board and horizontal in 19 mm thk prelam ply along the walls and partitions with necessary support from slab, joint between the prelam ply pelmet & the gypsum to be cladded with L-section 75 mm X 10 mm Aluminum angle finished in white powder coating as per detail complete. The rate to be inclusive of providing a ll accessories required for fixing pelmets complete. Mode of measurements:- Running Mtr. Length, No wastage to be added

Single Gypsum board above Pelmet; Providing and fixing Single Gypsum board above pelmet as per site conidtions, Gypsum board to be painted from one side facing towards fazade to have non visibilty from outside. Mode of measurements:- Sq.mtr. area. Front Elevation, one side only no wastage to be added

Roller Blind;Providing and fixing Mechanical roller blinds of approved make as per the manufacturer's specifications with drive unit, End plug, support brackets, roller tube, bottom rail, ball chains all described below. Drive unit to be of moulded plastic with straight rectangular support pin & inserted into the tube end. It shall be driven by a ball chain pulley and can be positioned at right or left side of the shade. The shade when lowering or raising shall automatically be lockable upon release of the ball chain by means of friction lock. End plug shall be moulded to plastic locking pin. The plug shall be inserted into the tube end. Support brackets shall be of zinc plated steel & provided with moulded plastic covers & used in right or left hand positions differentiated by acceptance of the rectangular drive unit support or the round idler plug pin. Roller tube shall be made out of roll formed steel of thick. Suitably protected against corrosion, & keyway integral with the tube to accommodate the spline , Out side diameter of the roller tube shall be 25mm. Bottom rail shall be a stiffening element inserted into a bottom rod pocket. Tube to be of the material as approved out of timber, PVC, steel or VB bottom rail. Ball chain shall be 2mm diameter cord with acetyl balls moulded co-axially to it on 6mm pitch to form ball chain. Rate to include the cost of decorative trims also.Openness shall be 5%. Mode of measurements:- Sq.mtr area.Front Elevation,No wastage to be added.

Classic Gypsum Skinning 12.5mm Thk;Providing & Fixing of 12.5mm Classic Gypsum Boards to be Screw fixed over existing framework with Drywall Screws of 25mm with 12nos per m2 at minium spacing of 600mm square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with a Jointing compound (Conforms to ASTM C475), a Paper tape or fiber tape.The board shall have stagered joint The junction of the partition with masonry & all penetration through the partition has to be treated with Hilti/Pyroplex fire and acoustic sealant. corner bead is applied at all corners. cost to be inclusive of making cutout & finishing for electrical, AV, & other services All other detailing and specifications to be followed as per approved drawing Mode of measurements:- Sq.mtr. area. Front Elevation, one side only no wastage to be added

48mm G.I. Framework;Providing & Fixing of 48x0.5mm G.I. C-stud placed at 610mm c/c in 50x0.5mm G.I. floor and ceiling channel. and on the other side Floor & Ceiling channel is anchored to the floor & True ceiling using Rawl plug Ø8x45mm zinc coated with pull out Load-6.8kN for M30 concrete grade at 600mm c/c in centerline. A G.I. Noggin channel of 48x0.5mm width has to be provided at the horizontal joints of the two boards. Mode of measurements:- Sq. Mt. area.Front elevation only,No wastage to be added

SKINNING ;

Classic Gypsum Skinning 12.5mm Thk ; Providing & Fixing of 12.5mm Classic Gypsum Boards to be Screw fixed over existing framework with Drywall Screws of 25mm with 12nos per m2 at minium spacing of 600mm square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with a Jointing compound (Conforms to ASTM C475), a Paper tape or fiber tape.The board shall have stagered joint The junction of the partition with masonry & all penetration through the partition has to be treated with Hilti/Pyroplex fire and acoustic sealant. corner bead is applied at all corners. cost to be inclusive of making cutout & finishing for electrical, AV, & other services All other detailing and specifications to be followed as per approved drawing Mode of measurements:- Sq.mtr. area. Front Elevation, one side only no wastage to be added

MDF Fluted Panelling;Providing & fixing 12 mm thick MDF Fluted panelling of approved shade / pattern / colour fixed on existing finished surface using adhesive & necessary hardware, etc as per detailed drawing. Mode of measurements:- Sq. Mt. area. Front Elevation, one side only.No wastage to be added.

Sliding folding partition - Solid - STC -45dB-2400mm High ;Providing and fixing Sliding folding partition made out of 100mm thk panels (max 1200mm width). Frames shall be clear anodizied aluminium, manually operated, top supported with retractable top and bottom seals, travelling along a ceiling track and assembled to form a solid wall. Vertical edges of panels will be protected with full-height aluminium trim. There shall be horizontal, vertical. top & bottom seals.The entire system must function as a solid wall and even when closed should reveal minimal screws, fixings or other similar metal parts. Each panel shall lined with Medium Density Fibreboard hung in acoustic free suspension from the panel frame. The panel shall be constructed to achieve55dB. with required acoustic sealing, suspension, tracking etc complete as per manufacturers details. Cost should be inclusive of above ceiling partition & MS Channel support work on sides Refer detailed specifications sheet. Mode of measurements:- Sq.mtr. area. Front Elevation, one side only no wastage to be added

Acoustic Felt Wall Paper;Providing and fixing 2mm thk Felt Acoustic Wall Paper of approved shade with recommended LOW VOC Adhesive of approved make. Cost to include preparation on the punned surface for receiving the wall paper as per the manufacturer specification. Mode of measurements:- Square meter : Front Elevation, one side only,No wastage to be added

MILL WORKS Reception Table 3000 X 750 mm;Top:- Providing and fixing Table top of size 50mm Thk X 3000mm L X 750mm W . Table shall be made out of 19mm thk double layer commercial ply cladded with 12 mm thk solid acrylic surface on all sides , with necessary frame & concealed support required etc complete as per details. Vertical Support- Vertical support made out of 19mm thk commercial ply frame cladded with 19mm thk commercial ply finish with18mm thk approved Marble / stone of first quality including cutting to any shape and set in kerakoll/laticrete/ardex adhesive backing & giving necessary slopes, cleaning joints and grouting them in neat.Care shall be taken to match the grains as directed. Further the stones shall be secured to the backing by means of necessary pins,cramps & dowels. concealed services to be complete before finishing with the cladding. complete as per detailed drawing and 3D view. Base :- Table made out of 19mm commerical ply with 1mm thk laminate from all sides. Front Side 19mm thk stone cladding of approved size / shade / color fixed using adhesive with 3mm thk epoxy spacer grout & Edges / Corners .Cost should be inclusive of Drawer Pedestal etc complete as per detailed drawing and 3D view. solid acrylic surface Basic Rate -800/-per sft Stone -200/- per sft Laminate Basic Rate -1450/- Per sheet-Sheet Size 8'X 4' Mode of measurements:- Numbers

STORAGES Low Height storage in laminate finish ;Providing and fixing storage unit of size 450 mm deep made out of 18 mm thk MDF ,Openable shutters made out of 18 mm thk MDF mounted on butterfly soft close hinges, All internal surfaces to be finished in 0.8 mm thk laminate and external surfaces to be finished in 1mm thk laminate finish storage units to have 18 mm thk. MDF adjustable shelves at 375 mm c/c. Back of storage unit to be out of 6 mm thk commercial ply . The cost to be also inclusive of finger groove handles, locks with key holes, PVC edge bind etc. All complete as per details and instructions by the architects. Mode of measurements:- Sq.mtr. area. Front Elevation, one side only no wastage to be added

Full ht storage in laminate Finish;Providing and fixing storage unit of size 450 mm deep made out of 25 mm thk blockboard ,Openable shutters made out of 25 mm thk blockboard mounted on butterfly soft close hinges, All internal surfaces to be finished in 0.8 mm thk laminate and external surfaces to be finished in 1mm thk laminate finish. storage units to have 18 mm thk. MDF adjustable shelves at 375 mm c/c. Back of storage unit to be out of 6 mm thk commercial ply . The cost to be also inclusive of 150 mm high SS concealed handles, locks with key holes, PVC edge bind etc. All complete as per details and instructions by the architects. Mode of measurements:- Sq.mtr. area. Front Elevation, one side only no wastage to be added

Full ht storage in laminate Finish;Providing and fixing storage unit of size 600mm Deep made out of 25 mm thk blockboard ,Openable shutters made out of 25 mm thk blockboard mounted on butterfly soft close hinges, All internal surfaces to be finished in 0.8 mm thk laminate and external surfaces to be finished in 1mm thk laminate finish. storage units to have 18 mm thk. MDF adjustable shelves at 375 mm c/c. Back of storage unit to be out of 6 mm thk commercial ply . The cost to be also inclusive of 150 mm high SS concealed handles, locks with key holes, PVC edge bind etc. All complete as per details and instructions by the architects. Mode of measurements:- Sq.mtr. area. Front Elevation, one side only no wastage to be added

Overhead storages in laminate finish ;Providing and fixing storage unit size 450mm Deep made out of 18 mm thk MDF ,Openable shutters made out of 18 mm thk MDF mounted on butterfly soft close hinges, All internal surfaces to be finished in 0.8 mm thk laminate and external surfaces to be finished in 1mm thk laminate finish. storage units to have 18 mm thk. MDF adjustable shelves at 375 mm c/c. Back of storage unit to be out of 6 mm thk commercial ply . The cost to be also inclusive of finger groove handles, locks with key holes, PVC edge bind etc. All complete as per details and instructions by the architects. Mode of measurements:- Sq.mtr. area. Front Elevation, one side only no wastage to be added

Display Storage;Providing and fixing storage unit made out of 25 mm thk blockboard ,Openable shutters made out of 10mm toughen glass mounted on butterfly soft close hinges, All internal surfaces and external surfaces to be finished in 1mm thk laminate finish. storage units to have 18 mm thk. MDF / 10mm toughen glass adjustable shelves at 375 mm c/c. Back of storage unit to be out of 6 mm thk commercial ply . The cost to be also inclusive of 150 mm high SS concealed handles, locks with key holes, PVC edge bind etc. All complete as per details and instructions by the architects. .The cost to be also inclusive of handles, locks, key holes etc. All complete as per details and instructions by the architects.

Low Height storage in granite finish top:Table Top - Providing and fixing granite Top made out of 19 mm thk machine cut & machine polished 1st quality Granite slab of approved make, color & shade set in kerakoll/laticrete/ardex adhesive as per detailed drawings. Storage Providing and fixing storage unit of size 450 mm deep made out of 18 mm thk MDF ,Openable shutters made out of 18 mm thk MDF mounted on butterfly soft close hinges, All internal surfaces to be finished in 0.8 mm thk laminate and external surfaces to be finished in 1mm thk laminate finish storage units to have 18 mm thk. MDF adjustable shelves at 375 mm c/c. Back of storage unit to be out of 6 mm thk commercial ply . The cost to be also inclusive of finger groove handles, locks with key holes, PVC edge bind etc. All complete as per details and instructions by the architects. Mode of measurements:- Sq.mtr. area. Front Elevation, one side only no wastage to be added

Low Height storage in laminate finish ; Providing and fixing storage unit of size 450 mm made out of 18 mm thk MDF ,Openable shutters made out of 18 mm thk MDF mounted on butterfly soft close hinges, All internal surfaces to be finished in 0.8 mm thk laminate and external surfaces to be finished in 1mm thk laminate finish storage units to have 18 mm thk. MDF adjustable shelves at 375 mm c/c. Back of storage unit to be out of 6 mm thk commercial ply . The cost to be also inclusive of finger groove handles, locks with key holes, PVC edge bind etc. All complete as per details and instructions by the architects. Mode of measurements:- Sq.mtr. area. Front Elevation, one side only no wastage to be added

Planter Box finish in Laminate;Providing and fixing Planter box of size 150mm high & 450mm wide as per design with necessary supports. Mode of Measurement:- Sq.mtr. area. No wastage to be added.Front Elevation, one side only.

CEILING AND PAINTING Classic - Gypsum Ceiling Work;Providing & Fixing Classic Gypsum Ceiling which includes G.I Perimeter Channel is fixed along the perimeter of existing wall/ partition at 600mm centres. G.I Ceiling Angle is suspended at up to 1.5m height by fixing it to the soffit clit with Soffit Cleat and or Rawl Plug- Ø8x45mm creating 1220mm x 1220mm grid. G.I Intermediate channel is fixed to the G.I Ceiling Angle with M6 x 12mm Hex Bolt & Hex Nut arrangement or with 2 Nos of Ø4.2x13 metal to metal screw .The G.I. Ceiling Section is then fixed to the G.I. Intermediate Channel with the help of Connecting Clip and in direction perpendicular to the Intermediate channel at 457mm c/c. Single layer of 12.5mm thick Plain Gypsum board is then screw fixed to ceiling section with 25mm drywall screws at 230mm centres. Finally square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Jointing Compound & Joint Paper tape. Serrated steel section has effective thickness of 2T (2xdepth), better load carrying capacity, enhanced screw retention, Improved acoustic performance & fire resistance as compared to plain steel section. Cost should be inclusive of necessary cutouts for light fixtures, speakers, sprinklers, anyother services etc. The rate shall also include providing perimeter channel for grills, lights, diffusers as called for in HVAC and Electrical Drawings. The rate shall also include providing for edge/angle bits at all corners, necessary taping, filling with jointing compound as per manufacturers specifications. Mode of measurements:-SqM area. Surface, no wastage to be added

Cove Ceiling;Providing and Fixing Gypsum board cove ceiling as per detail drawing and direction of the architects. With provision and cutouts for fixing light fittings, cable, conduits etc running internally, AC grill fixing etc.

Laminate ceiling;Providing and fixing Laminate ceiling made out of 12mm thk commercial ply frame work cladded with 9mm thk commercial ply finished with factory laminated 6mm thk commercial ply. Laminate to be 1mm thk in approved make / shade / figures with groves & direction as per detailed drawings. All above ceiling surfaces should be painted with Black japan. The ceiling shall be suspended from trueslab with necessary supports. Cost should be inclusive of cutouts for lights, grills, any MEP services etc. Laminate Basic Rate -1500/- per sheet-Size of laminate 8 X 4 Mode of measurements:- Sq. ft. area. Surface, no wastage to be added

Modular Ceiling ;Metal Grid Ceiling-(1200X 300 ) Providing and fixing Metal Grid Ceiling powder coated as per make as approved by Architect in metal tiles with approved surface pattern of size 1200 mm X 300 mm with 24mm T grid.

Entrance Mat ; Providing 3M Nomad / Euronics Entrance mat of required size as per manufactuer's specifications Mode of measurements:-Square meter,No wastage to be added.

Room Signage in SS / Aluminium with Laquer approximatye size 12" x 3". Font and text as given by client

Push & Pull Signage in SS / Aluminium with Laquer approximatye size 3" x 3". Font and text as given by client

Fire Evacuation Plan in Auto glow with 3mm + 3mm Sandwiched Acrylic panel fixed with SS studs

Fire Exit hanging signage-4mm thick laser cut acrylic with photoluminescent film + UV printing and matt over lamination.Hanging using SS rods. Double sided.

BRIT Logo Main Company logo made in app. colour 3mm thk acrylic sheet, fixed and installed as per design. The design will include individual letters in block, font and size as per client's company standards and brand specifications. Approximate size for the purpose of quotation 5'-0" L and 12" ht and having depth of 1". The logo design to be approved before manufacturing and installation. Single Glaze Modular Partition;Providing and fixing single glazed partition in line, level and plumb made out of 10 mm thk toughened glass using top & bottom channel of approved size. Partition Dimension as approved. Glass to glass butt joint with I-joint, T-section & 90 degree sections & Glass packing to adjust the floor level. All the glass and section junction and joints are sealed with dry joint acoustic gaskets. The sound reduction Value to be achieved is 32 to 36 Db. Finish: All aluminium section work to be of approved powder coated / anodizied finish. Mode of measurements:- Sq.Mtr .Front Elevation area , one side only

Single Glaze Modular Partition - 45mm wide Specs as above, including: Top & bottom channel: 40mm x 25mm Partition Dimension: 40mm x 25mm

Glass Door with Aluminum Door Frame; Providing & fixing 12mm thk Toughened Glass door Door type: Rebated hinged Glass door in aluminium door fram Frame: Anodizied / Powder coated aluminium door frame, incorporating acoustic seals Frame dimension: 55mm x 40mm Finish: All aluminium section work to be of approved powder coated / anodizied finish Frame for Single Door includes for butt hinges, 4 nos Mortise Lock with Lever Handle, Door Closer Hold open / Concealed , Bottom drop seal, Key Hole, Half moon door stopper Ironmongery Finished in Silver approved powder coated / anodizied. Mode of measurements:- Numbers

Single leaf: length 1200mm x Height 2400mm -(D-02)

Double leaf: length 1800mm x Height 2400mm -(D-08)

SOLID FLUSH DOOR IN LAMINATE FINISH; Providing & fixing 40mm thk flush door with 1 1/2" X 1/4" lipping patti on all sides, finished in 1 mm thk.Laminate on both side of approved shade as per architecs instructions complete with all necessary hardware such as 3nos SS hinges, half moon door stopper, Dead lock with Key hole, 450mm high handle from both sides, Hold Open Door closure etc. Mode of measurements:- Numbers

Solid flush door 900 mm X 2400 mm height

Solid flush door 1000 mm X 2400 mm height

Solid flush door 1500 mm X 2400 mm height

Solid flush door 1800 mm X 2400 mm height

Solid flush door 2000 mm X 2400 mm height

Designing, supplying, fabricating, testing, transporting, handling and erecting at required positions and levels Structural Steel members for for space frame as per approved design and drawing including girders, steel beams,rafters, purlins, cleats, fixing accessories, connection fasteners, girts, wind bracings and all structural members required to support roofing, rain water gutters, lighting windows including epoxy painting and making provisions stated as below including all consumables. This shall comprise of the following : Primary members: Primary members such as transverse rigid frames, curved rafters and wind bracings, bearing frame rafters, supports for rain water gutters etc. using three plate technology or as per approved design (Using Grade 310 mpa yield strength) Secondary Members: Secondary members such as purlins, girts, eaves, struts, wind bracing, flange bracings, base angles, clips, and other miscellaneous structural parts using cold rolled forming technology.( Using 310 mpa Yield strength) Connections: All field connections shall be bolted. primary field connections shall be bolted and shall conform to relavent IS code and Secondary connections shall conform to relavent IS. Provisions as shown in drawing for : a) Openings for windows, ventilators, etc. with suitable steel members or frames on all the sides of the opening. All fabricated structural steel shall be painted with epoxy protective paint of approved make minimum 2 coats and 150 micron dry film thickness of approved colour after surface preparation by sand blasting. Notes : 1) All fabrication including welding shall be carried out in the factory only and no site fabrication will be permitted. 2) Detailed design and Drawings , shop drawings shall be prepared by the contractor through specialised pre engineered building agency/ experienced consultant and submitted for approval and detailed design report, Loading details / reactions shall be given for design assesment. 3) Conceptual aesthetically pleasing supporting system shall be worked out and submitted for approval before proceeding detailed design.

Providing Structural steel work using angles, channels, joists and other sections, welded and / or bolted in built up sections for trusses , structural steel floors, frame works, monorails and other structures including supplying, cutting, welding, fabricating, hoisting, fixing in position, applying a priming coat of approved steel primer etc. complete all as per specifications, wings and as directed by the Project Engineer. Above 300 mm Joists, 350 mm channels, sections Using materials manufactured by SAIL/ RINL/ TATA or any other approved brands of BARC confirming to IS 2062. All test reports to be provided along with the supply of the materials.

Providing and fixing expansion hold fasteners of 'HILTI' make in expansion hold fasteners in CC / RCC surface including RE-500 chemical, backing including drilling necessary holes, cleaning holes and the cost of bolt etc complete as per direction of Engineer-in-charge and finished smooth.

HILTI make HSL 3 M 10/20

HILTI make HSL 3 M 24/30

Designing, providing and fixing of 4 mm thick approved make and shade Aluminium Composite Metal Panel of approved make cladding at different locations including soffits of over-hangs and including aluminium frame work with grids filled in with weather silicon sealant as per the drawings. The ACM panel composition shall be of 0.5 mm thick PVDF coated aluminium sheet + 3 mm thick low density polyethelene virgin resin core + 0.5 mm thick polyester (PVDF) coated Aluminium sheet all complete as per approved shop drawings and specification Note : ACMP shall be measured to the actual visible area of the ACP sheet including silicon joints as fixed on site.

Providing and fixing anodized aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically whereever required including cleat angle, aluminium snap beading for glazing / panelling, C.P brass / stainless screws all complete as per drawings and and directions of Engineer-in-charge including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required filling the gaps using silicon grout sealent etc. (fittings glazing and panelling shall be paid for separately)

Anodised Aluminium sections (Minimum anodizing thickness of 15 micron)

Extra for Colour Anodizing / Dyed anodizing on Aluminium sections & sheets

Providing and fixing approved quality stain less steel body roller wheels of approved make for sliding shutters

Providing and fixing approved quality and shape star locks cum handle of approved make for sliding shutters

Providing and fixing glazing in aluminium doors, window, ventilator shutters and partitions etc with PVC / Neoprene gasket etc. complete as per the architectural drawings and directions of the Engineer-in-charge (Cost of snap beading shall be paid in basic item) With tinted colour float glass panes of 4.0 mm thickness

Kitchen drawer basket ; Providing & fixing 3drawer baskets set made out of Haffle Tandembox Plus M & D-Height Stainless Steel Dawer, soft closing drawer. SS drawer baskets will be used for Cutlery, Cup, Saucers, Plates, or multipurpose as directed by Architect. Baskets size -650L X 600 W X 450D Mode of measurements:- Numbers,No wastage to be added.

Aluminium Framework ; Providing & Fixing of Aluminium section framework with Aluminium horizontal members of 50mm x 50mm size placed at 600mm c/c to the vertical members forming framework upto ceiling level and at underside of beam/slab levels as per site conditions. sections to be rigidly fixed to vertical members with all the necessay "L" clit to form sturdy stucture. Aluminium member to be minimum 1.2mm thk (16gauge). complete as per instruction by engineer in charge. Rate also include 40mm thk Acoustic 6 rockwool slab of density 48kg/m³ shall be placed in metal framework. Rockwool holding clip should be used to hold rockwool slab in its position. Rockwool to be fully covered with fiber paper. Mode of measurements:- Sq. Mt. area.Front elevation only,No wastage to be added.

Providing Comprehensive Architectural consultancy Services, Designing & Liaison work for all interior, services, PH works, HVAC, STRUCTURAL, Electrical, with issue of all GFC drawing , BOQs and specifications for Renovation of Entrance lobby, CE cabin, staircase , display room, Meeting room . The works has to be carried through specialized agencey like M/s BEYOND DESIGN ARCHITECTS & CONSULTANTS or approved equivalent and as directed Engineer-in-Charge etc complete. Payment will be made to consultant as per following: Note : Payment terms 70 % on GFC 25 % during work progress 5 % on completion and handover

Section- B (ELECTRICAL WORKS) LT PANEL with SWITCH GEARS: Design, Supply, installation, testing and Commissioning of LT PANEL with SWITCH GEARS:(Removal of old panel and refixing of new LT panel) SLD is the part of Specification please refer.

Main LT panel (As perattached SLD)

10 KVA Ups output panel (As perattached SLD) CABLING & TERMINATION :Supply & laying of following 1100 V grade PVC insulated,Aluminum / copper conductor, armoured cable rate to include G.I. clamping, support etc. XLPE Insulated & Steel Armoured Aluminium Conductor Cables

3.5 Core X 185 Sqmm

4 Core X 25 Sqmm

4 Core X 16 Sqmm

4 Core X 10 Sqmm

PVC insulated & Steel armoured Copper conductor cables(YFY Types) 4 Core x 10 Sq. mm

4 Core x 6 Sq. mm

3 Core x 6 Sq. mm

3 Core x 4 Sq. mm

3 Core x 2.5 Sq. mm

PVC Insulated & Un Armoured Copper flexible Conductor cables (YY Type) 1 Core x 16 Sq. mm

1 Core x 10/6 Sq. mm

END TERMINATIONS :Removing and Refixing of Existing End terminations for the below listed cables including supply of single compression type brass glands, solder less crimping type copper sockets / lugs, Identification tags, Cu. clamp & wire for gland earthing etc., XLPE Insulated & Steel Armoured Aluminium Conductor Cables 3.5 Core X 185 Sqmm

4 Core Core X 25 Sqmm

4 Core X 16 Sqmm

4 Core X 10 Sqmm

PVC Insulated & Steel Armoured Copper Conductor cables (YFY Type) 4 Core x 10 Sq. mm

4 Core x 6 Sq. mm

4 Core x 4 Sq. mm

4 Core x 2.5 Sq. mm

3 Core x 6 Sq. mm PVC Insulated & Un Armoured Copper flexible Conductor cables (YY Type)

1 Core x 10/16 Sq. mm

MCB DISTRIBUTION BOARDS :Wall mounted MCB DBs with MS wire way box on top / bottom & on sides. MCBs shall be rated for 10kA with current limiting feature. Dummy ways to be covered with blank plates. All out going ways shall be labelled & laminated as built drawing (SLD) shall be

ELDB's: TPN MCB DB Enclosure : IP 42 Sheet steel, Incomer : 1Nos. 40A, FP, MCB Isolator, Sub Incomer : 3Nos. 25A 30mA DP RCCB,Outgoing :18Nos. 10A SP MCB of 'C' curve

TPN MCB HVAC DB,Enclosure : IP 42 Sheet steel,Incomer : 1Nos. 63 A, FP, MCB Isolator,Sub Incomer : 3Nos. 63A DP 100mA RCCB,Outgoing : 18 Nos. 20A SP MCB of 'C' curve

ELDB's /HVAC DB's:SPN MCB DB ,Enclosure : IP 42 Sheet steel,incomer : 1No.40A DP, MCB type isolator,Outgoing : 8 Nos. 16A SP MCB of 'C' Curve

Server Room DB's :SPN DB,Enclosure : IP 42 Sheet steel,incomer : 1No. 40A DP, MCB - D' Curve,incomer : 1No. 40A DP, MCB - D' Curve,SPD

EPDB's : TPN MCB DB,Enclosure : IP 42 Sheet steel ,incomer : 1No. 63A FP, MCB type isolator,Sub Incomer : 3Nos. 40A DP MCB,Outgoing : 24 Nos. 16A SP MCB, D'curve

PDB's : TPN MCB DB,Enclosure : IP 42 Sheet steel,Incomer : 1Nos. 63A, FP, MCB Isolator,Sub Incomer : 3Nos. 40A 100mA DP RCCB,Outgoing :24 Nos. 16A SP MCB of 'C' curve

8 Way TPN MCB DB-Café DB :Enclosure : IP 42 Sheet steel ,Incomer : 1Nos. 40A, FP, MCB Isolator,Sub Incomer : 3Nos. 25A 100mA DP RCCB,Sub Incomer : 3Nos. 25A 100mA DP RCCB,Outgoing :24 Nos. 16A SP MCB of 'C' curve

EMG MAIN DB's:Enclosure : IP 42 Sheet steel,Incomer : 1Nos. 40A, DP, MCB, Outgoing : 6 Nos. 25 SP MCB of 'C' curve

CIRCUIT / SUB MAINS:: Circuit mains using 1.1kV grade PVC FRLS insulated copper conductor wires / sheathed single core cables drawn in MS conduits. Rates quoted shall include supply of conduits, wires & other conduiting accessories. Circuit mains shall be measured from respective DB to the nearest control switch /socket board and further to the adjescent SB if any. There shall not be any joints in the circuits, only looping is allowed in terminal blocks & in switches / socket outlets. UPS / RAW/lighting RP Circuit: Lighting Circuit : To wiring using (3R x 2.5) sqmm pvc insulated FRLS wire drawn in Suitable Size of Ms conduit as lighting circuit, being recond from the distribution board to first light control switch.

Supply & Installation of 3C x 2.5 Sqmm FRLS 1100V unarmoured double insulated flexible multicore cable in Suitable Size of MS Conduit

Supply & Installation of 3C x 4 Sqmm FRLS 1100V unarmoured double insulated flexible multicore cable in Suitable Size of MS Conduit

Supply & Installation of RG-6 flexible cable in Suitable Size of conduitt for TV point.

Supply and Laying Cat 6 Cable in Suitable Size Of MS Conduit Rate Should Incul With RJ 45 Socket Face Palte and Connecter Ferrules

2 x 6 sqmm copper conductor wires in 25mm dia. conduit.

Floor Pop-up Box / Floor Boxes comprising of 2Nos of 2x13A Intel Soc + 1x16A Sw. & Data Face Plate provision. Make: As per Arch Base Cost Rs.18500.000

Connector / Distribution Block - 1 in 3 out type. Make: Connet System / Mayer

Connector / Distribution Block - 1 in 5 out type. Make: Connet System / Mayer

Connector / Immidiate coupler - 1 in 1 out type. Make: Connet System / Mayer

POWER RECEPTACLES. Supply, Installation, Testing and Commissioning of the following Modular/Industrial Switch, sockets with modular front plate, and accessories as per the site conditions, Note: Safety shutters to prevent accidental contact with live parts shall be provided. No indicator shall be provided for switches

1 nos. 6A socket controlled by 6A SP switch

1 nos. 13A socket controlled by 16A SP switch

1 nos. 13A socket controlled by 16A SP switch (Faceplate to be Black in colour)

2 nos. 13A socket controlled by 16A SP switch

3 nos. 13A socket controlled by 16A SP switch

4 nos. 6A socket controlled by 16A SP switch

1 no. 5/15A socket controlled by 16A SP switch

2 nos. 5/15A socket controlled by 16A SP switch

Server / Hub room Rack Sockets

1 No 6/16A Universal Socket outlet Controlled by 16ASPSw + 1 No 32A 3 pin 1Ph Industrial Scket with plug top controlled by 32A SP MCB (DP/ FP MCB Tye Isolators in MS Enclosure)

40/ 63A, DP MCB in IP 42 MS Enclosure.

40/ 63A,, TPN MCB in IP 42 MS Enclosure.

40/ 63A, RCBO 300mA in IP 42 MS Enclosure.

25A, DP MCB in IP 42 MS Enclosure.

POINT WIRING: Supply, Installation, Testing & Commissioing of Wiring of light points, fan points, 6A socket outlets using MS Conduit conduit of 19mm dia with accessories, using 3 runs of 2.5 Sqmm 1100v grade PVC FRLS insulated copper wires, modular switches with MS box, plate & accessories. point drops shall be by flexible conduit. The cost of circuit to be measured seperately.

PRIMARY LIGHT POINT: Primary light point means wiring from first switch control to the first light point. Cost of switch to be considered,Not to include the incoming lighting circuit from MCB - DB to switch.

POINT WIRING - MCB Control Primary light point means wiring from MCB control in DB to the first light point

SECONDARY LIGHT POINT: Secondary light point means extention of light outlet point from adjascent light points existing.

CABLE TRAYS :GI ready made cable trays. Quoted rates for installation shall include necessary anchor fasteners / 'L' angle supports @ 600mm interval etc., to suit site conditions PERFORATED TYPE :

450x50mm Size

300x50mm Size

200x50mm Size

150x50mm Size

Supply & Installation of 150mmx 75/50mm GI Trunking 2mm thick with cover to be used for running the wires/cables. Trunking to be fixied on wall partition with suitable size of GI clamp, The rate shall include the cost of Supports . Trunking should have knock outs on both side

EARTHING : Maintenance Free Earth pits Eathing system shall be installed as per supplier guidelines /details. Rate shall include necessary civil works.Type-1 : Single Rod configuration. EARTH STRIPS: GI/Cu earth strips on cable tray or below ground as per site condition. All Cu. Strips shall be run in pvc heat shirnkable sleeve & mounted on insulation mounts. Cost of civil works shall be included for strips laid below ground. All main GI earth strips.

8 SWG GI Wire

25 x 3mm GI Earth flat

25 x 6mm GI Earth flat

50 x 6mm GI Earth flat

Busbar of 0.5 Mtr length made out of 50x6 mm GI strip with drill holes of M8 at 25mm interval mounted on insulators.

Busbar of 0.5 Mtr length made out of 25x6 mm Cu. Strip with drill holes of M8 at 25mm interval mounted on insulators.

PVC Insulated & Un Armoured Copper flexible Conductor cables (YY Type) 1.1kV grade, copper conductor, PVC insulated, unarmoured, power cables. The cables shall be laid on tray / hume pipe /in ready made trenches, with nylon cable ties / MS Clamps @ 600mm interval etc., as required. Rate quoted shall exclude cost of tray / hume pipe

1 Core x 70 Sq. mm

1 Core x 50 Sq. mm

1 Core x 35 Sq. mm

1 Core x 25 Sq. mm

1 Core x 16 Sq. mm

1 Core x 10 Sq. mm

End terminations for the below listed cables including supply of single compression type brass glands, solder less crimping type copper sockets / lugs, Identification tags, Cu. clamp & wire for gland earthing etc.,

1 Core x 70 Sq. mm

1 Core x 50 Sq. mm

1 Core x 35Sq. mm

1 Core x 25Sq. mm

1 Core x 16 Sq. mm

1 Core x 10 Sq. mm

MISCELLANEOUS ITEMS: 6mm thick rubber mat of 1.1KV class and 1000mm wide

Shock treatment chart as approved by the Electrical Inspectorate mounted on teak wood frame and suitable for wall mounting.

First aid kit

4.5 KG capacity carbon di oxide ( CO2 )

5 Kg DCP

Temporary Lighting & Power arrangement Sufficient temporary Lighting (Min 150Lux Ave) & power shall be provided to all agencies durring execution with required no. of Industrial type FTL light fixtures & Socket outlets, till commissioning stage.

Removing and Refixing of Existing electrical services.

Lighting BOQ

Supply, Installation, Testing & Commissioning of LED strip in Cove (HIGH DENSITY) 14 watts per meter, IP42, Driver at each 3 meter distance with LED strip+SMPS) SMPS should have proper enclosure with ventillation arrangement.(Make: Philips/Wipro/Panasonic)

Installation of Light Fitting as per Drawing and 3D View (Attached Layout drawing if any)

Section: C (HVAC WORKS SUPPLY OF VRF UNITS:)Prices shall be based on supply, installation, testing & commissioning at site including all taxes, duties, transportation & insurance etc. All cabling shall be armoured type Supply of following type VRF units with scroll compressor. The units should be complete with indoor unit, condensing unit, controls, microprocessor control panel, internal wiring, refrigerant piping, etc. The units should be compactible with VAV/VRT technology with auto charging facility. Note: The control panel shall have incoming power MCCBS/MCBs as per VRF unit control panel specs. Refrigrant shall be R410A only. The VRF units should be suitable for servicing from the bottom and top panel. The individual control panel should be microprocessor based as per specs. All the AC unit control panels location will be as approved by Consultant/ Architect. It should be possible to start and stop the unit from remote locations. Outdoor units should be installed as per the site condition. Outdoor units should be coated with anti rust coating. Outdoor units shall be with Cowl piece.

Supply of Daikin make DX Cassette units. 2.0 TR Cassette units - Inverter ( Model No : FCVF71ARV16 )

Installation,Testing & Commissioning of Dx units 2.0 TR Cassette units - Inverter ( Model No : FCVF71ARV16 )

Dismentling / shifting & Reinstallation of Existing 2.0Tr Hi-wall split unit

Supply & Installation of P V C Drain piping with insulation

Dia - 25 mm

Dia - 32 mm

Supply & Installation of MS Stand for Outdoor Unit ( Table top stand )

2.0TR Cassette units

2.0Tr Hi-wall split units

TOPPING UP OF REFRIGERANT GAS

Supply & Installation of G I Ducting 24 G

Supply and Installation of ducting insulation

13mm thick Thermal insulation class "o"

19 mm thick Thermal insulation class "o"

Supply & installation of Site Fabriacted Z piece with GI & Close cell nitrile rubber

Supply & installation of Plenum

1000w x 100 D x 300Ht

1100w x 100 D x 300Ht

1350w x 100 D x 300Ht

850w x 100 D x 300Ht

Supply & installation of AL powder coated Slot diffuser 3slot Diffuser

Supply & installation of Flexible Duct

250mm dia

300mm dia

350mm dia

400mm dia

Supply & installation of BY Pass - VAV Box

VAV-BP -300

VAV-BP-350

VAV-BP-400

Supply & installation of Copper piping for DX units

2.0TR Cassette units ( 3/4" ; 5/8" )

Existing 2.0Tr Hi-wall split unit ( 1/4" ; 5/8" )

Supply & installation of Control cabling

Duct modification work

Supply & installation of 150mm dia Propeller fan

Section : D (UPS SYSTEM) Supply & installation of 10KVA UPS 3 Ph I/P & 3 Ph O/P for infrastructurer load and compatible for redundant configuaration with 15 minutes battery back up 10 KVA UPS with 3 Phase Input - 3Phase Output Model : EASY Series

Approved SMF Battery for Approximate 15Min Backup on Load WITH 0.8 PF Factor - 12V/26AH Quanta / Exide

Racks & Links with 10 Mtr of UPS to Battery Cable (5Mtr for Positive & 5 Mtr for Negative)

Battery DC Breaker with Under / Over Voltage Coil for Battery & UPS Safety & Commissoning

SNMP CARD

External Aluminium K1 Rated Isolation Transformer of 10KVA

Section : E (FAS WORK) Removing and Reinstallations of 1 LOOP Intelligent Addressable Analogue type Micro Processor - controled Main Fire Alarm Control Panel with Cross Zone facility for Activating the FM200 Gas Releae module, complete with the LCD Diplay, Feather Touch Key Board,inbuilt RAM memory for history Log, with Battery Back up.(UL/LPCB Approved)Make-Morley

Removing and Reinstallatios Addressable Photo electric type smoke detecters (UL/LPCB Approved) ()Make-Morley

SITC Addressable Photo electric type Smoke detecters For AFC (UL/LPCB Approved) ()Make-Morley

Removing and reinstallations Addressable Manual call points near Entry /Exists (UL/LPCB Approved)Make-Morley

Removing and reinstallations Addressables hoter cum flashers (UL/LPCB Approved)Make-Morley

SITC of Junction Box

SITC of ISI Marked 2 core x 1.5 mm2, Copper, FRLS Armoured cable, laid on surface with GI saddle-spacers every 0.3 meters. Complete with GI Junction Box, lugs, cable compression glands, cable tags and Ferruling.

Closed Circuit Television:Removing and reinstallations of IR Dome Camera: 1/3'' Super HAD fixed focal lens 3.6mm, 20 M IR distance including all mounting supports / brackets and fixing accessories. (Hikvision) .

Removing and reinstallations12 V 3Amp power Supply

Removing and restalltions 16 Channel DVR and RACK with inbuilt cum encoder for IP with Robust Embedded LINUX OS on High performance TI embedded microprocessor with VGA Output with Dual Streaming output, Support Dynamic IP, MPEG -4 / H.264, 30 fps@D1 on all Channel, Recording/Display, work with low bandwidth network,HDMI output Display operation for live monitoring and separate display for recording playback, Screen pop-ups on motion or alarm activation,Digital watermark,E-map,Multi level passwords protection.Network Function TCP/IP, UDP, DHCP, DNS, IP Filter, PPPOE, DDNS, FTP, Email, Alarm Server, RSTP, RTP. Addition to above it also can be networked for centralised server with Storage for back-up. (Make - HIK-VISION)

RG 6 Cable for CCTV in PVC conduting

2 core cable for power in PVC conduting

Section: F ( NETWORKING) Supply and Laying of Cat 6 Utp Cable is Suitable Size of PVC Conduit

Supply and Fixing of RJ 45 Sockets with Plate and Surface Boxes.

Supply, installation,testing,commissioning of one no of Single CAT6 faceplate with blankings if required.

Supply and Insatallation of Patch cord 3ft

Supply and Insatallation of Patch cord 7ft

Supply and Fixing of 12 u Rack

Removing of existing from OLD premisses to New Premises 50 NOS DATA & VOICE

Supply,Installation,Testing & Commissioning of Layer 2 Managed Switch: 48 x 10/100/1000 Mbps, 4 x 10G SFP+, Model No.: DGS-1510-52X with stacking cable.

MAHENDRA REALTORS AND INFRASTRUCTURE PVT LTD