Providing Internal and External electrification to the construction of additional building for Commercial Tax office at Commercial Tax Officer Complex at Madurai in Madurai District

Amount

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End )

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plateand making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End.

Wiring with 3 x1.5sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Higher End.

Supply and run of 1.5sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in Existing rigid pipe concealed in wall and ceiling with necessary connection complte.

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End ). Street light points

Wiring with 2x1.5sq.mm. PVC insulated single core unsheathed FRLS copper conductor cable of 1100V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accesories with MS switch Box and 5A FTswitch with painting of suitable colour continuous earthwire connection of 1.5sq.mm copper wire for lightpoint /fanpoint (for electronic regulator)

Wiring with 2x1.5sq.mm. PVC insulated single core unsheathed FRLS copper conductor cable of 1100V grade in suitable heavygauge MSconduitpipe onwall and ceiling with MS accesories with 150mmx100mmx75mm MS switchbox for 5A3pin non interlocking flushtype CSplug wfth painting of suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for open plug point.

Supply and fixing of single box type 4'-20 W LED fitting with CRCA body complete with TW round blocks on wall or ceiling with 20 W LED tube with PVC unsheathed FRLS Copper leads from terminals to the fitting.(Higher end)

Supply and fixing of Twin box type 4'-20 W LED fitting with CRCA Body complete with conduit pipe suspension with PVC unsheathed FRLS Copper leads from terminals to the fitting with 2Nos 20W LED tube light.(Higher end)

supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of 9W LED bulb for BH point .(Higher end).

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1No.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting.

Supply and Fixing of 20W LED batten Mirror Light on Wall with PVC Unsheathed FRLS Copper Leads from terminals to the Fitting.

Supply and fixing of WT bulk head fitting with guard suitable with 7W / 9W LED bulb.

Supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 600mm down rod on the existing fan clamp.

Supply and fixing of 300 mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall.

Supply and fixing of louvers shutters arrangements for 300 mm (12") sweep (light duty) AC exhaust fan.

Supply and fixing of 400mm (16 inch) wall mount, Oscillating type fan with aerodynamically designedsemi transparent PP three blades for noise free operation with in built Speed regulator with necessary accessories with connections complete (Havells make Accelero HS/ Crompton High Flo Wave/ Usha Maxx Air/Eq.)

Supply and fixing of 24W LED square type Surface mounting fitting (Havells / Integra / Nxt DL / Eq) with aluminium (99% purity) sink, available in square shape PC diffuser in white powder coated finish with built in electronic low THD (<10%) LED driver 6500 KCCT : CRI > = 80 with 1.50 sq.mm PVC unsheathed FRLS copper wire from terminals to the fitting and necessary connection complete.,

Supply & Fixing of AC / DC 76mm Buzzer /call bell suitable for 230 Volts 50 c/s single phase AC supply with 1Module GI flush mounting box,I Module combined plastic cover plate and 1module Modular type Bell push Switch with indicator complete(The GI flush mounting box,cover plate and switch should be of Higher End.

Supply and fixing of 3 nos.6A two module 3 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box ( GI ) in flush with wall with connections. (Higher end)

Supply and fixing of 1 no.6A two module 3 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End.

Supply and fixing of 1No. 6/16A two module socket, 1No. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI) in flush with wall with connections. Higher End.

Supply and fixing of 20A Flush type Wall socket with 32A DP MCB ampere for aeplug in flush with wall with earth connection (For AC Plug)

Supply and fixing of 32A DP MCB in sheet steel enclosure in flush with wall with earth connection and making good of the concealed portion. [The MCB and metal enclosure should be of higher end.

Supply and fixing of 63A FP MCB in sheet steel enclosure in flush with wall with earth connection and making good of the concealed portion. [The MCB and metal enclosure should be of higher end.

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 16A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 4way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 100A 4P MCB switch as incoming and 4nos. 63A TP MCB as outgoing in flush with wall with earth connection only. Higher End.

Supply and fixing of 7 segment 4 way TPN MCB distribution board in sheet steel double door type with metal door with IP42 protection with 63A FP MCB as incoming and 3 Nos 63A DP RCCB as sub incomer and 12 Nos 6A to 32A SP MCB as outgoings in flush with wall and making good of the concealed portion with earth connection. (Higher End) (FF - 2Nos + SF - 3Nos)

Supply and fixing of 4 way 7 segment triple pole neutral MCB distribution board in sheet steel enclosure double door type with metal door with IP 42 protection with 40A 4 pole MCB as incoming and 3Nos 40A DP RCCB with 30mA sensitivity as sub incomer and 12Nos. 6 A to 32A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. (Higher End)

Supply and run of 2 of 1.5sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 1.5sqmm copper wire and making good of the concealed portion with suitable colour (For call bell ,5A plug)

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion.

Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4sq.mm copper wire and making good of the concealed portion with suitable colour.

Supply and run of 4 of 6sq.mm. PVC insulated SC unsheathed RLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 6sq.mm copper wire and making good of the concealed portion with suitable colour. Essential DB

Supply and Run of 4 of 16 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 16 sq.mm copper wire and making good of the concealed position.Power DB

Supply and Laying of 31/2 x185 Sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. 250A switch or 250A panel

Supply and fixing of brass cable gland for 3-1/2 x 185 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and clamping of 31/2 X 185 Sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps

Supply and providing cable end termination of 31/2 X 185 Sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete.

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection.

Supply and run of 2 of 6 Sq.mm PVC insulated SC unsheathed FRLS Copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continous earth wire connection of 6 sq.mm copper wire and making good of the concealed portion with suitable colour.

Supply,erection,testing and commissing of Suitable Split type AC unit ABS plastic split type inverter AC units Conforming to IS.1391(part-2) with AMT 1 to 2 fitted with inverter compressor operating on refrigerant (non-CFC) suitable for wall mounting) expect power consumpition norms suitable for operation on 230V.50Hz single phase AC supply with star rating of 5 as per BEE specification and capable of performing the functions of 1) Cooling 2) Dehumidifying 3) Air circulating 4) Filtering The installation work for the above split type AC units inculds the following 1.Mounting /fitting indoor and outdoor units at their respective locations. 2.Laying refrigerant pipe line of required length connecting both units after drilling hole/holes in the wall if required.Thickness of the copper tubing shall not be less than 0.8mm. 3.Insulating the suction pipe with expanded polythylene foam 5mm tubing. 4. Laying 25mm dia flexible PVC drain pipe to throw out the consensate water being formed with in indoor unit. 5.Leakage testing the entire system gas in the unit. 6.Charging refrigerant gas in the unit. 7.Suitable electric wiring to be provided with 2.5 sqmm PVC insulated copper wire between indoor units upto 6 mtrs length and up to switch with in 3 meters of the location of indoor unit. 1.50TR (4500 K Cal / Hr)

Supply,erection,testing and commissing of Suitable Split type AC unit ABS plastic split type inverter AC units Conforming to IS.1391(part-2) with AMT 1 to 2 fitted with inverter compressor operating on refrigerant (non-CFC) suitable for wall mounting) expect power consumpition norms suitable for operation on 230V.50Hz single phase AC supply with star rating of 5 as per BEE specification and capable of performing the functions of 1) Cooling 2) Dehumidifying 3) Air circulating 4) Filtering The installation work for the above split type AC units inculds the following 1.Mounting /fitting indoor and outdoor units at their respective locations. 2.Laying refrigerant pipe line of required length connecting both units after drilling hole/holes in the wall if required.Thickness of the copper tubing shall not be less than 0.8mm. 3.Insulating the suction pipe with expanded polythylene foam 5mm tubing. 4. Laying 25mm dia flexible PVC drain pipe to throw out the consensate water being formed with in indoor unit. 5.Leakage testing the entire system gas in the unit. 6.Charging refrigerant gas in the unit. 7.Suitable electric wiring to be provided with 2.5 sqmm PVC insulated copper wire between indoor units upto 6 mtrs length and up to switch with in 3 meters of the location of indoor unit. 2.0TR (6000 K Cal / Hr)

Supply and Installation of 4KVA Electronic Automatic Voltage Stabilizer Input Voltage range of 150Volt - 285Volt and Output Voltage range 200Volts to 230 Volts with High and Low Voltage cut off and 3 minutes time delay relay with demonstration.

Supply and Installation of 5KVA Electronic Automatic Voltage Stabilizer with Input Voltage range of 150Volt - 285Volt and Output Voltage range 200Volts to 230 Volts with High and Low Voltage cut off and 3 minutes time delay relay with demonstration.

Supply and Laying of 5/8" and 3/8" copper pipe (Extra beyond 3 meters supplied with AC unit.

Supply and fixing of MS stand for fixing outdoor unit.

Design, Engineering, supply, fabrication, erection, testing, commissioning and handing over of 1No 16persons capacity Gearless with machine room passenger lift with Stainless steel panels with disabled freinedly micro processor based controller VVVF drive fire rated doors and ARD . As per the following technical specifications with free Guarantee period of one year from the date of commissioning. Technical specifications: 1. Type of lift : passenger lift 2. Capacity of lift : 16persons capacity passenger lift 1088 Kg 3. Speed : 1.00 Meter/Sec 4. Type of Drive: specific variable voltage variable frequency V3F drive with enhanced ride comfort and leveling functions. 5. No. of floors: Ground + 2 floor ( Travel 6.9 Mtrs) 6. Leveling Accuracy: High level 7. Construction of Car: 18 SWG high quality stainless steel 304 grade car, Hair line finish stretcher impact protection car size 1300 mm x 2000 mm. 8. Position of machine: Directly above the lift well. 9. No. of landing entrance: 3 Nos 10. No. of car entrance: one in front only

19. Indication: UP/Down digital direction and position indicator for all landing and in car 20. Emergency alarm bell: Battery operated alarm bell to be provided with Automatic charging device 21. Emergency light: Battery operated light to be provided with Automatic charging device 22. Fire Man’s switch: To be provided at ground floor 23. Minor builders work: included in the scope. 24. Scaffolding: Included in the scope 25. Sill angles and facia plates: included in the scope 26. Steel for lift machinery: Included in the scope 27. Servicing and maintenance: Free comprehensive servicing and maintenance should be provided by lift contractor during the guarantee period of one year. 28. Automatic Rescue device: To facilitate the landing of the lift to the nearest floor at the time of power failure. This shall consist of suitable type battery system with charger, invertor, under voltage protection system etc., complete with all accessories.

29. Provision of intercom with phone: To be provided by lift contractor with one handset in the lift car and another handset in the lift machine room with telecom exchange unite with one trunk and three extension linked proton 103 matrix telecom unit and required length of single twisted pair with thickness of 0.5 mm to 1 mm connecting the handsets and telecom exchange unit. 30. Lift License: Preparation of Drawing, payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate as per lift act should be done by lift contractor. 31. Floor annunciator with music. 32. Special features: a. Infra red door sensor with full height screen. b. Full width half height rear panel mirror. c. Tubular stainless steel hand rail in cars.

d. Voltage stabilizer for circuit control. e. Stainless. Steel signal fixtures. f. Vandal proof S.S. Button with S.S. cover g. SS door frames for landing doors. h. VF door operator. i. Call Register signal j. Stainless steel facia plate for car operating panel and landing fixtures. k. On – Off switch for fan and light l. Over load warning indicator with audio announcement 33. Other standard features: Over speed governor, phase failure and phase reversal relay, T. Guide brackets for car and counter weight, rubber padding under winding unit, motor of adequate capacity, electro mechanical door locks emergency keyside supporting angles, motor over load protection devices final limit switch main suspension ropes counter weights lifting joist for mounting the machineries

34.Lift License : Preparation of Drawings, payment of inspection charges to CEIG and insurance policy and Obtaining CEIG approval for the Lift as per Lift act should be done by the Lift contractor.Site testing in accordance with IS 14665 should be carried out at the time of handing over. 35. Supply of operation and maintenance manual with necessary tools for operation. 36. Guarantee: Free Guarantee for the materials and workmanship of equipments complete should be offered by lift firm for a period of one year from the date of commissioning.Make should be approved by the departmental officer before used on work.

1. 250 A TPN switch disconnector fuse uni interior only with HRC fuses double break - IN 2. 100 A TPN switch disconnector fuse units interior only with HRC fuses double break - 2Nos 3. 63A TPN switch disconnector fuse units interior only with HRC fuses double break - 8Nos. In each cubical switch, live portion of bus bar should be shrouded by 6mm thick hylem sheet sepearator and properly earthed by tinned solid copper flat as per CEIG specifications. All the doors should be provided with suitable locking arrangement with rubber beedings. The earth bus with two runs of 1" x 1/4' tinned copper flat must be run all round the panel to provide double earth connection. The panel should be painted with two high quality enamel paint over one coat of red oxide primer, the cable size, capcity of switch, loaction etc., should be superscribed with white paint on each incoming and outgoing switch with metalllic danger board shall be affixed complete with mounting on base channel iron frame work support complete (The TPN switches make should be appproved by departmental officers before used on work.)

Supply and fixing of 250 A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses double break on suitable angle iron frame work with MS cable entry boxes with earth connection only.

Supply and Laying of 4 x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (For St.light )

Supply and clamping of 4 x 16 sq.mm PVC LTUG armoured aluminium cable on post or on wall with MS Clamps.

Supply and fixing of brass cable gland for 4 x 16 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 4 x 16 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED street light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour.

Supply, Testing Commissioning and Handing over of 40 kVA Diesel Generator set with acoustic enclosure conforming to CPCB IV+ Norms and BIS Specifications with Standard Control Panel of 0.8 P.F. Three phase 415V/ 420 Volts, 50Hz, 1500 RPM CPCB Approved capacity developing 56 HP with acoustic enclosure water cooled clock wise rotating feed pump with 32KW/ 40KVA operating capacity brushless alternator close coupled underneath fuel tank standard safeties LLOP with stop solenoid battery with lead Electric start and vibration fitting and accessories and standard control panel as detailed below including transporting & unloading charges.

(A) Engine: Water cooled diesel engine suitable for Generator application conforming CPCBIV+ norms and IS standards with a shaft out put of 56 HP at 1500 RPM under NTP conditions. The Engine shall comprise the following standard fitting flexible coupling fly wheel, air cleaner, fan blower, radiator, water pump, fuel filter, lubricating oil filter, etc. (B) 12 Volt Electronic starting Equipment: Complete with starter motor, dynamo, standard batteries with cable, flexible exhaust piping of 50cms length (C) Engine Instrument Panel / Mounted: Starting push botton / starting key, lubricating oil, temperature gauge, lubricating oil pressure gauge, water temperature gauge, safety control for low lubricating oil, pressure, safety control for high water temperature, safety control for over speed, hour meter (mechnical) and RPM indicator, battery charging ammeter. The engine should be capable of providing 10% over load for one hour for every 11 hours continuous at full load.

D)ALTERNATOR: 40kVA/32kW Capacity of brushless alternator, AC 3 phase, 50Hz, 415/420V, 0.8 PF, 1500 RPM under NTP conditions, conforming to CPCB IV+ Norms. E) STANDARD CONTROL PANEL : The standard control panel (cubical) should be vermin proof and dust proof best quality sheet steel of 16 SWG CRCA MS sheet and floor mounted with suitable hinged glass doors and enamel painted. The panel should be microprocessor based complete with suitable Square/ Rectangular copper bus bars with internal connections and with necessary cables and other accessories and with tapings for the incoming supply from the alternator and for the outgoing supply to the load and incorporating Suitable MCCB and HRC fuses, Set of control fuses, etc. with following facilities.

1. UNDER / OVER LIMIT i. High coolant Temperature ii. Low lube oil pressure iii. Over speed iv. Start fail v. Emergency stop vi. Over load 2. FAULT INDICATIONS: i. LLOP - Low Lub. oil pressure ii. HWT - High water temperature iii. OL - Over load iv. E.STOP - Emergency stop v. DG - Gen set ON vi. LOAD - ON 3.Metering & Protective relaying: i) Multi function Digital panel meter with the functions of Ammeter , Voltmeter, Frequency Meter, Power factor meter, KW meter, KWHr Meter .- 1No 2) Current transformers of suitable ratio. – Set of 3Nos. 3) Earth fault relay – 1No

G. Exhaust Gas Recirculation system arrangements as per CPCB IV+ norms as amended H. BASE FRAME: Base frame should be fabricated with MS channel frame of rigidly welded construction for mounting of generaor set. The engine and alternator should be coupled by suitably designed diaphragm type flexible coupling with guard and mounted on the base frame with proper alignment. I) ACOUSTIC ENCLOSURE: The Acoustic enclosure, Self standing weather proof Acoustic canopy conforming CPCBIV+ norms floor mounting type with modular construction with the provision to assemble and dismantle easily and designed to suit all weather condtions and compliance to IS standards. Erection of acoustic enclosure suitable for 40KVA Diesel generator complete with all accessories as above and suitable supports etc. as approved by competent authority to suit updated CPCB norms. J) Erection of generator set with proper alignment over the existing foundation.

K)Supply of manuals for operation & maintenance of DG set with warranty card etc. L) CEIG approval: Preparation of site plan physical layout, electrical line schematic Diagram 10 sets, getting drawing approval from CEIG preparation of complection report rectification report etc., arranging CEIG inspection and obtaining CEIG safety certificate, payment of CEIG inspection fees if necessary and preparation of one set of approval Drawing and copy of safety certificate in a neat frame work. M)TESTING AND COMMISSIONING After the installation of DG set on its foundation, the DG set should be tested and commissioned with first charging of lubrication oil to its level, first charging of battery and run the set for eight hours on full load test complete. The Genset engine and alternator make should be approved by department officials before used on work.

Providing suitable concrete foundation suitable for 40 kVA Generator set with Plain Cement Concrete 1:2:4 (one cement, two sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing etc., complete as per standard specifications and as directed by the departmental officers, to Madurai CTO.

Supply and fixing of 100A Three phase 500V 4Pole Change over Switch on suitable angle iron frame work with MS cable entry boxes with earth connection only.

Supply and Laying of 3 1/2 x 50 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. 100A changeover, VTPN

Supply and clamping of 3-1/2 x 50 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps.

Supply and fixing of brass cable gland for 3-1/2 x 50 sq.mm. PVC armoured LTUG cable with earth connection.

Supply and providing cable end termination of 3 -1/2 x 50sqmm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and run of 25 mmx3 mm tinned copper flat with necessary clamps /supports on wall /floor /ground for earth connection.

T PAULKANNU & CO (BID ID -1416093)

ANNAI ELECTRICALS (BID ID -1405027)