Beautification of Verinag Market by way of street lights and Sign boards

Supply, Installation, Testing and Commissioning of Heritage architectural ornamental decorative cast iron pole as per specification/ drawing (enclosed) Phillips/Bajaj/Homdec/Mayfair/Dwarka/ eq. make as approved by EIC with the following specifications:- The decorative ornamental pole shall be made out of Grooved Mild Steel tube in multiple sections as per attached drawing. Total height of the pole shall be 3000mm nominal above the ground.The different sections shall be joined together through flanges and swaging joints and are welded to get stable structure. The bottom section shall be of 133mm dia x 3.0mm thickness x 1000mm long, the top section shall be of 72mm dia x 3.0mm thickness x 2000mm long. The base plate shall be of dimension dia 300mm and thickness 10 mm and joined with the pole by welding joint with the help of stiffeners. A built in service window shall be provided to accommodate a 6 amp SP MCB and 32 amp heavy duty connector for mains connections in the bottom part of the pole as shown in the attached drawing. The cast iron decorative embellishments shall be fixed with the pole with the help of SS grub screws as shown in attached drawing. The decorative pole shall be machined and polished properly to give it a smooth surface. The decorative pole shall be duly pretreated by shot blasting process and coated with high end epoxy primers and top coat in UV ray resistant polyurethane/Polyester coating in approved colour shade. The Coating on the pole shall be baked in oven at required temperature and parameters. The DFT of coating on pole shall be 90 microns (minimum). The coating on pole and bracket shall pass minimum 300 salt spray hours. Wind pressure calculation shall be done as per IS875 for wind speed of 180 km/hr.The pole manufacturer shall have inhouse facility for pole fabrication consisting of Laser cutting machine, Pole fabrication and Mig welding plant, shot blasting machine, Oven to bake required pole and bracket. The EIC will visit the plant to ascertain the required plant and machinery at manufacturers facility.. Mentioned dimensions are proposed dimensions, which may vary with actual measurements (Tolerance of ±5%) Further the pole shall be got approved by the concerned engineering wing after providing a sample before execution of work and the test certificate to be provided by the manufacturer.

Supply and fixing of ornamental Cast iron and mild steel 2 way bracket painted with anti-corrisive enemal paint as per design, of Mayfair/Dwarka or of equivalent make as approved by EIC /design (as per enclosed drawing) The Double Arm decorative bracket made out of mild steel tube with cast iron and cast aluminium embellishments. Total Width of the Double Arm decorative bracket shall be 990mm. The brackets design shall be same as shown in attached drawing. The Bracket Shall be suitable to be fitted on Lighting Pole. The decorative bracket shall be machined and polished properly to give a smooth surface. The decorative bracket shall be duly pretreated by Shot Blasting & Sanding process and coated with high end epoxy primers and top coat in UV ray resistant polyurethane/Polyester coating in approved colour shade. The Coating on the bracket shall be baked in oven at required temperature and parameters. The DFT of coating on bracket shall be 90 microns (minimum). The coating on bracket shall pass minimum 300 salt spray hours.The pole manufacturer shall have inhouse facility for pole fabrication consisting of Laser cutting machine, Pole fabrication and Mig welding plant; Shot blasting machine, Oven to bake required pole and bracket. The EIC will visit the plant to ascertain the required plant and machinery at manufacturers facility

Supply, Installation, Testing and Commissioning of Decorative Led Street Light. It shall be made of cast & spun Aluminum and shall have Ingress protection of IP66 for optical compartment and Impact Resistance of IK 08 or more. The effective Height & Width of the Led Street Light shall 420mm width x 400mm height. The Led Street Light shall be in 54w LED. Transparent polycarbonate Diffuser shall be fitted in the Led Street Light. Integrated suitable BIS approved LED Driver shall be fitted inside the Led Street Light having efficiency >85%, power factor shall be>0.95, THD<=10%,with driver standard voltage withstand range of 100-300V AC and inbuilt surge protection of min 4KV. The Luminaire shall have external surge protection device of 10KV. Led shall be Osram/Seoul/Cree/Bridgelux or equivalent reputed make as approved by EIC and shall have luminous efficacy of more than 140 Lm/Watt. System luminous efficacy shall be more than 120 Lm/Watt. The CCT of Led shall be 6000K as required by engineer in charge. The shape and sizes of the Led Street Light shall be as per attached drawing. System life of 50,000 burning hours with 70% of initial lumens maintained. The Led Street Light shall be machined and polished properly to give it a smooth surface and shall be coated in UV ray resistant Polyurethane/ Polyester coating in approved colour shade. The Coating on the Led Street light shall be baked in oven at required temperature and parameters.The street light manufacturer shall have in house testing facility for Street light luminaire viz- LM-79, IP-66, IK-08. Oven to bake coating required luminaire. The EIC will visit the plant to ascertain the required testing equipments, plant and machinery. Following third party test reports will be required with the material. LM-79 IP-66 IK-08 LM-80 FOR LED BIS OF DRIVER BIS OF STREET LIGHT

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres:

Providing and laying in position cement concrete including curing but excluding the cost of shuttering and centring with 1:1.5:3 (1 cement, 1.5 Coarse sand, 3 Graded stone aggregate 20 mm nominal size). The dimensions of the block should be 3'x2'x2'.

Steel reinforcement for R.C.C. work ready to use "cut and bend" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete.Thermo-Mechanically Treated bars of grade Fe-500D or more with 40kg/cum.

S/L , testing and commissioning of PVC alluminium armoured cable 650 V/1100 V Grade as per IS 7098 (Part 1) 1988 with upto Date Amendments.Havell/Eq. standard make as directed by engineer incharge and making end termination with brass compression gland and aluminium lugs of required size.

a) 25 sq.mm 4 core

a) 10 sq.mm 4 core

Providing of service connection and earthings to luminaire from the junction box in 1.5 mm PVC insulated, multicolour copper wire (FRLSH) . Havells/Polycab/SSK/KEI/ eq. make as approved by EIC

Earthing with G.l. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal coke and salt as required.Complete Job.

Supply and installation of Spiral Earthing through 10 swg GI wire after driving in ground up to a depth of 3' in the ground from the base of the pole.

Main Panel

Design, Fabrication, Supplying, Installation, Testing and Commissioning of following panel made out of 2mm thick M.S. sheet, , vermin and dust proof, Outdoor type with suitable size of angle iron legs grouted in the cement concrete., with lockable type hinged doors, duly painted with provision for fixing of incomer MCCB, outgoing DP MCBS, sets of Aluminium Bus Bar of different rating. after taking Derating factor into account, and other allied accessories etc. as required. the panel to be fabricated from reputed firm duly approved by CPRI.as per approved design, size may vary as per site requirement)

Providing and fixing of following protection equipments and other allied accessories including connections, inter connections, with suitable size of PVC insulated copper conductor cable including earthing etc. as required.

INCOMING:

a)100 amp TPN MCCB 35 KA including spreader links, (Adjustable thermal and Adjustable magnetic release ) Legrand/ Shinider/L&T/ABB / eq. make to be approved by EIC.

b) 4 No. of Aluminium Bus Bar of 250 Amp.

c) digital time switch astronomical (GIC ASTRO)

d) 40/63A automatic modular contactor with manual override (Havells/L&T,Schnider/ eq. make to be approved by EIC)

OUTGOING:

a) 63 amp TPN MCB

b)5-32 SPMCB

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting the concrete path wherever required,jointing etc.direct in ground including excavation and refilling the trench with soft excavated earth making the surface level but excluding sand cushioning and protective covering etc., complete as required.

63 mm dia (OD-63 mm & ID-51 mm nominal)

SIGN BOARD

Providing, supplying, installing, testing and commissioning of Advertising Moving Board (Scroll Type) of size 6 ft × 3 ft (18 ft²) each, complete in all respects. The work includes fabrication and supply of MS frame duly painted, scroll mechanism with motor and rollers, display surface, electrical wiring and control system, civil foundation/anchoring, fixing, painting and all accessories as required for proper operation. The item rate shall be inclusive of all labour, material, equipment, transportation, taxes and incidental charges for complete execution at site.Complete Job.