Spl repair to certain Bldgs MD Accn at Naria defence Enclave and provn of security light alongwith the Boundary wall of Defence Enclave, Naria, BHU at Varanasi Cantt under GE (East) Prayagraj.

Amount

Demolition of cement concrete (reinforced) of any description and in any position (reinforcement cut as required to facilitate demolition) not other wise specifically provided for complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 25mm thick Cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in levelling course, benching etc, finished even & rough to receive the toping layer complete all as specified and directed.

M&L for 75mm thick Cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in levelling course, for floor benching etc, finished even & rough receive the toping layer complete all as specified and directed.

M&L for chequered cement concrete tiles 25 cm x 25 cm x 22-25 mm thick, machine pressed set jointed and pointed in neat cement slurry in floors with grey cement and pigment over and including 15 mm thick screed bed in CM (1:6 ) complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) in plinth protection, finished surface even and smooth without using extra cement, complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Roughening surfaces of old concrete floors by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and directed.

M&L for Non - skid Coloured Ceramic tiles 7 to 8 mm thick, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 20 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

All as per item No. 09 above but as in vertical surfaces such as skirting/ dado over and including rendering layer 10 mm thick in CM (1:4) complete all as specified and directed.

M&L for Glazed ceramic tiles in vertical surface, size 450X 300X 7mm thick , set and jointed in neat cement slurry and pointed in white or colour cement to match tiles over and including 10 mm thick rendering layer in CM (1:4) complete all as specified and directed.

M&L for Machine cut Kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing over and including 20 mm thick screed bed or bedding layer in CM (1:4) complete all as specified and directed.

M&L for Kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed base with grey cement mixed with pigment to match the shade of slab including rubbing and polishing over and including 10 mm thick screed bed or bedding layer in CM (1:4) complete all as specified and directed.

Demolition of brick work built in cement or cement lime mortar complete all as specified and directed.

M&L for Brick work with fly ash old size bricks, straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for Brickwork with fly ash old size bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:6 on faces of brick work or concrete wall surfaces, finished even and fair complete all as specified and directed.

M&L for rendering 10 mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces, finished even and fair complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even and fair complete all as specified and directed.

S&F GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste complete all as specified and directed.

M&L for preparing new plastered or un plastered surfaces of walls by applying 1 mm thick wall care putty to prepare the surface even and smooth and finishing with two coats of Oil bound distemper in approved colour/shade complete all as specified and directed .

M&L for preparing new plastered or surfaces of walls by applying 1 mm thick wall care putty to prepare the surfaces smooth and finishing with two coats of cement base paint in approved colour/shade complete all as specified and directed.

M&L for preparing new plastered or surfaces of ceiling applying three coats of white wash complete all as specified and directed.

M&L for complete removal of existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, filling depressions of scrapped surfaces by applying 1 mm thick wall care putty to prepare the surface even and smooth and finishing wall surfaces with two coats of Oil bond distemper complete all as specified and directed.

M&L for complete removal of existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, filling depressions of scrapped surfaces by applying 1 mm thick wall care putty to prepare the surface even and smooth and finishing wall surfaces with two coats of cement base paint complete all as specified and directed.

M&L for complete removal of existing treatment (any number of layers) from old surfaces of ceiling and applying two coat of white wash complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and directed.

M&L for Makrana white Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window sills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed .

S&F in repair 15mm dia GI steel tubes, medium grade with all fitting and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F in repair 20mm dia GI steel tubes, medium grade with all fitting and fixed complete to walls and ceiling or laid in floors complete all as specified and directed .

S&F in repair 25mm dia GI steel tubes, medium grade with all fitting and fixed complete to walls and ceiling or laid in floors complete all as specified and directed .

S&F in repair 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed .

S&F in repair Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity, ISI marked double layered, hoisted and fixed in position including connecting up pipes including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (minimum weight 210 gms) complete all as specified and directed.

S&F in repair 20mm PVC tank nipple suitable for HDPE water tank. (Minimum weight 45gms) complete all as specified and directed.

S&F in repair PVC low level flushing cistern 10 litres capacity, white, with all fitting and fixtures including brackets and 32 mm bore PVC flush pipe, complete all as specified and directed.

S&F in repairs Vitreous china squatting pan ‘Orissa’ pattern, size 580 x 440 mm, white coloured, with integral foot rests, including provision of lime concrete bedding complete all as specified and directed.

S&F in repairs Vitreous china wash basin, white, flat back, size 550x400 mm including brackets and cutting for and pinning in ends of brackets, complete all as specified and directed.

S&F in repair brass chromium plated soap dish complete all as specified and directed.

S&F in repair Brass chromium plated shower rose 125 mm size with swivel joints, complete all as specified and directed.

S&F in repair Tubular towel rail of brass chromium plated, 20 mm dia, 'D' type, 60 cm long between flanges including brackets complete all as specified and directed.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F in repair fancy type bib taps cast copper alloy chromium plated with crutch or butter fly handle screwed down screwed for iron pipe 15mm bore complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in chajjas complete all as specified and directed. Note : reinforcement to be measured separately under respective item.

M&L for form work to chajja or slab and similar work for flat rough finished concrete surface complete all as specified and directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 6 to 8 mm dia as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exc 10cm girth complete all as specified and directed.

S&F in repair 15 mm dia cast copper alloy chromium plated angle valve, fancy type with long shank and cup, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S&F in repair 15 mm dia stop valves cast copper alloy chromium plated long shank (concealed type), screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S&F in repair stainless steel tubing of 25 mm dia as in curtain rod, fancy type including and brabs brackets, socket and knobs (wall to wall or flush to wall) for securing curtain rod, complete all as specified and directed.

Taking down chowkhat with shutters (W/O taking off shutters from the frame) area of each opening exc. 1.50 Sqm but n exc. 4 Sqm complete all as specified and directed.

Taking down chowkhat with shutters (W/O taking off shutters from the frame) area of each opening exc. 1.50 Sqm complete all as specified and directed.

Taking down shutters of any description area not exceeding 1.00 Sqm, complete all as specified and directed .

Taking down shutters of any description area exc 1.00 Sqm but n' exc 2.00 Sqm each, complete all as specified and directed .

S&F plain framed panelled shutter ( two panels), factory made, 35 mm thick, 2nd class HW rail and style with lock rail and panels of timber flat on both sides feather edged, or of veneered particle board medium density or particle board with commercial face, size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F glazed and skeleton shutters 9Factory made), 35mm thick, 2nd class HW rail and style, open rebated and prepared to receive glass or gauze etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitered bead for securing glass/gauze etc size of member of shutter as specified in SSR part I section 8, clause 8.24(a) complete all as specified and directed.

S&F 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and jointed at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickens. The Lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm ( + 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two laces by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete all as specified by the manufacturer and as per directions of Engineer-in-charge.

S&F factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 42x50 mm (tolerance ± 1 mm), and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge .

M&L for Rolled mild steel sections conforming to Gde Fe-410-0 (Grade E-250) quality A as in framing for cladding, glazing and the like including door frames/chowkats, fixed with angle cleats and connecting plates, etc complete all as specified and directed.

M&L for PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) as in hold fast blocks including necessary form work complete all as specified and directed.

S&F 200 mm long aluminium anodised, barrel tower bolts of extruded section and fixed, complete all as specified and directed.

S&F in repair 200 mm long aluminium anodised, barrel tower bolts of extruded section and fixed, complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt 250 mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F in repair Aluminium alloy, anodised, sliding door bolt 250 mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F butt hinges, medium weight, cold rolled mild steel, 100 mm size complete all as specified and directed.

S&F Aluminium handles, cast type anodised 150mm size complete all as specified and directed.

S&F in repair Aluminium handles , cast type anodised 150mm size complete all as specified and directed.

S&F Aluminium handles, cast type anodised 100mm size complete all as specified and directed.

S&F in repair hasp and staple 150 mm size, safety type aluminium anodised with mild steel hinge pin including bolt to hinge plate, fixed with screws in repair complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed complete all as specified and directed.

S&F 25mm thick PVC Insulated Panels having expanded polystyrene (EPS) stuck to 2mm thick Panel with wood grain printed PVC sheet used instead of plain colour sheet PVC as in Cup board etc. sheet duly fitted into the wall with PVC frame as per specifications complete all as specified and directed .

S & F Continuous (piano) hinges, mild steel, bright finish or electro galvanised width of flaps 30mm (when open) complete all as specified and directed.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, with glazing bars complete all as specified and directed.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, without glazing bars complete all as specified and directed.

S&F factory made steel ventilators with top hung shutter including hinges, steel peg stay including two coats of synthetic enamel paint over a coat of red oxide primer after preparation of new steel surfaces complete all as specified and directed.

S&F 3mm thick sheet plain glass ordinary quality and glazing with oil putty in squares n exc. 0.50 Sqm in each panes complete all as specified and directed.

S&F, 3mm thick Figured glass, pin headed type and glazing with oil putty in squares n exc 0.5 sqm in each pane complete all as specified and directed.

S&F in repair of 3mm thick sheet plain glass ordinary quality, and glazing with oil putty or wooden beads in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed .

M&L for mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for preparing new surfaces of wood and wood based materials of any description over 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparing old painted surfaces of wood and wood based materials of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparing old painted steel & iron surfaces of any description over 10 cm in width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

M&L for preparing new steel & iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F in repair 110mm PVC (SWR) pipes single socketed , in any length with rubber ring, joints, laid in trenches or in floors complete all as specified and directed.

S&F in repair 110mm PVC (SWR) pipes single socketed , in any length with rubber ring, joints, fixed to walls complete all as specified and directed.

S&F in repair 75mm PVC (SWR) pipes single socketed , in any length with rubber ring, joints, laid in trenches or in floors complete all as specified and directed.

S&F in repair 75mm PVC (SWR) pipes single socketed , in any length with rubber ring, joints, fixed to walls complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction single (Single T)equal or unequal complete all as specified and directed.

S&F 75mm bore PVC (SWR) junction single ()equal or unequal complete all as specified and directed.

S&F 110mm PVC (SWR) Vent cowl complete all as specified and directed.

S&F 75mm PVC (SWR) Vent cowl complete all as specified and directed.

S&F in repairs PVC (SWR) floor trap, plain with grating including jointing jointing to waste pipe with solvent cement, fixed in cement concrete type B1 (1:2:4), suitable for 75mm bore pipe complete all as specified and directed.

Demolition and breaking up drain pipes Internal dia of pipe in 150 mm (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed.

M&L for 150mm dia Salt-glazed stoneware drain pipes laid in trenches and jointed as specified including Bends and taper bends, any radius complete all as specified and directed.

M&L for concrete bed to 150 mm bore drain pipes including packing under and completely surrounding pipes with concrete after they are laid and tested; in, PCC 1:3:6 type C2 (using 40mm graded stone aggregate) complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair stainless steel plate rack (utensil rack) of size 600mm x 750mm and depth 300mm made with 0.63mm thick stainless steel sheet provided with brass screw including necessary fittings, nut/bolts complete all as specified and directed.

S&F in repair Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/ plastic cleats (minimum weight 300 gms) complete all as specified and directed.

S&F in repair 15mm bore fancy type pillar tap cast copper alloy with capstan head chromium plated screwed down high pressure with or without lettered 'hot' or 'Cold' with long screwed shanks and fly nuts fixed to pipe complete all as specified and directed.

M&L for Plain cement concrete, 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) as in surface channels or drains, complete all as specified directed.

M&L for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc, complete all as specified directed.

M&L for providing cement concrete type B-0, 1:2:4 (using 12.5mm graded crushed stone aggregate) and mixed with water proofing compound, as in roof kerbs or mud stops, roof padding, rounded or chamfered on edges and misc surfaces complete all as specified and directed. (Note: water proofing compound shall be paid separately).

M&L for treatment of leakage/ seepage from roof/ sunken portion by applying a glass fibre reinforced acrylic modified cementinious coating complete all as specified and directed. The process shall comprising the following:- (i) Removing the filling in sunken portion including demolition Complete (from toping layer to concrete surface of roof), removing the debris where directed, cleaning and washing the surface to make ready to receive the water proofing coating. (ii) Repairing/ sealing the joints, mouth of RWP/spout ,crack(s) or pore/hole,if noticed, using sealing material mixed with sealing compount with antire setisfection of Engineer-in-charge. (iii) provide 20mm thich (average ) cement plaster in cement mortar (1:3) mixed with WPC on floor and side walls after fixing a chicken wiremesh. (iv) Applying glass fibre reinforced acrylic modified cementinious coating using RFX brush bond mixed with Neto bond in the proportion as per manufacturers instructions as to make the coating 1mm thick. NOTE : (a) The cost of checken wiremesh and WPC shall deemed to be included in quoted unit rated of this item.

Contd/... (b) Any treatment shall only be start only after the stage passing of preparation of surface by GE in writing and shall be produced at the time of claiming payment. (c) after treatment and before fill up the shunken potion contractor shall crryout a POND TEST for 72 hours and the certificate from Engineer -in-charge for 'No leakage/ seapage noticed' shall be prodused at the time of claiming payment. (d) Contractor shall produce gaurantee for 7 years in wrinting (on leater head) for any leakage/ seapage along with final Bill in addition to security amount as mentioned in tender socument. (f) contractor shall produce the purchage Vouchers for entire quanitity of cement and products used.

M&L for PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in filling in mass concrete (sunken floors) complete all as specified and directed.

Demolition of mud in roofs any thickness and in any position and leaping over roof terrace ,removing the demolished material to a distance exc 250 m & n exc 500 m and depositing where directed at a level n exc. 1.5 m above starting point, complete all as specified and as directed.

M&L for screed bed 10 mm thick in cement mortar 1:3 over roof slab mixed with water proofing compound ( WPC to be measured and paid separately) as per manufacturer’s instructions finished even & fair complete all as specified and directed.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed.

M&L for priming surface with approved bitumen primer confirming to IS-3384-1955 @0.50 Kg per Sqmm and applying hot blown grade 85/25 bitumen as per IS 702-1988 @1.2 Kg per Sqm and laying of polymeric water proofing membrane asphaltic polythene film of weight not less than 3Kg per Sqm with minimum 100mm side lap and 150mm along the length from down lamps to upward completely sealed with hot blown lamps complete all as specified and directed.

M&L for Preparation of new surface of APP membrane and treating/applying two coat of heat resisting paint complete all as specified and directed.

M&L for cement concrete tiles of size 20cm x 20cm x 20mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished built with grey cement and no pigment over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Supply only integral water proofing compound (powder) complete all as specified and directed.

M&L for 75mm thick Cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) in levelling course, for floor etc, finished even & rough to receive cement mortar screed bed complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade and with grey cement and pigment including 25mm thick sand cushning complete all as specified and directed.

M&L for reinforced cement concrete Type B-1 ,1:2:4 (using 20 mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Use and waste form work in flat surfaces to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, complete all as specified and directed.

S&F in repair 15mm bore stop valves, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed.

S&F in repair 20mm bore stop valves, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed.

S&F in repairs grating doom 125 mm dia with waste hole of PTMT (min weight 40 gms) complete all as specified and directed.

S&F powder coated aluminium door single leaf sliding with powder coated aluminium frame of section 62.5 x 37 x 1.5 mm thick, shutter with bottom & middle rail of section 112.50 x 37 x 1.5mm thick, shutter with bottom & middle rail of section 112.50 x 37 x 1.5mm thick and styles & top rail of section 83 x 37 x 2.5 mm thick with centrally locking arrangement with lock make of 'GODREJ' or 'LINK' seven lever and self closing device with rebate including jointing cleats, fixing of builders hardware fittings, necessary numbers of sliding roller and glazing with 5.5mm thick ordinary plain glass including necessary fittings, fixtures & aluminium snap beads complete all as specified & directed.

S&F powder coated aluminium window / CSW / Ventilator with powder coated aluminium anodized frame of aluminium section 62.5 x 37 x 1.5 mm thick with shutters having styles & rails of powder coated aluminium section 44.45 x 44.45 x 1.5mm thick including jointing cleats, glazing clips, rubber packing, aluminium snap beading, screws anodized aluminium fittings such as hinges, tower bolts, handles etc including 5.5mm thick ordinary plain glass complete including providing and fixing aluminium chequered grill of anodized section of mesh 100 x 100mm of 08 mm dia of aluminium bar fixed to frame with 20 x 20mm aluminium flat with screw and stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm complete all as specified & directed.

S&F aluminium extruded section body door closer hydraulically regulated designation No. 3 universal type suitable for aluminium door shutters (weight of shutter between 61 to 80 Kg) complete all as specified & directed.

S&F solar/sun control film having 25 micron reflective type sticked to glass panes of aluminium doors or windows as required as per instruction of manufacturer complete all as specified and directed.

Dismantling of asbestos cement (corrugated or semi corrugated etc.) sheet roof coverings complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & directed.

S&F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position framed work complete all as specified and directed.

M&L for Second class hard-wood as in scantlings, timber framed and fixed complete all as specified and directed.

M&L for roof trusses (framed), trussed, purlins, crane gantries, pillars, rails and fastenings and heavy bracket framing (beam, tee, angle, channel, Hollow or flat sections) including distance pieces, cleats etc conforming to Fe 410-W (Gde - E-250) quality - A complete all as specified and directed.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

M&L for GI frame work snap grid false ceiling size of grid 605 mm x 605 mm including adjustable hook and wire for false ceiling and section of grid as specified in SSR Part I-2009 including 4 mm thick designer white pre-laminated self embossed, texture Insulation and acoustic purpose E-board, properly fixed on grid complete all as specified and directed.

Taking down carefully aluminium point wiring(any type)for one light point, fan point ,exhaust fan point, bell point, power point complete including all fittings such as switches, socket, pendants holder, ceiling rose, sketch fittings, tube light fittings, regulators unscrewing the switch sockets, ceiling rose, regulators from boards/outlet boxes and making good the disturbed surfaces of wall/ ceiling and colour washing matching with the existing colour wash complete all as specified and directed.

M&L for point wiring complete with PVC insulated unsheathed, 1100 volts grade cable 1.5 Sqmm (nominal area) FRLS type multi stranded copper conductor, single core drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring for one light/fan/bell/buzzer / exhaust fan point controlled by one, one way switch, including concealed pressed steel terminal box of required size not less than 1.0 mm thick factory made duly painted inside & outside with two coats of black bituminous paint over & including a coat of red oxide primer, with 2.8 mm thick top cover of plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc including 1.5 Sqmm FRLS type PVC insulated unsheathed cable multi-stranded copper conductor as continuous earth wire and connected to earth dolly as required at site& including chases cutting & making good disturbed surface & applying finishes to match existing surface complete all as specified and directed.

Ditto- all as item No.138 here-in-before but for one light controlled by two way switch

Ditto- all as item No. 138 here-in-before but one 3 pin, 5amp socket out let on independent board complete all as specified and directed.

Ditto -all as item No. 138 here-in before but 3pin ,5amp socket outlet on the same board with other switch complete all as specified and directed.

M&L for point wiring complete with PVC insulated unsheathed, 1100 volts grade cable 2.5 Sqmm (nominal area) FRLS type multi stranded copper conductor, single core drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring for one 15/16/ Amps socket outlet point controlled by one, one way switch, including concealed pressed steel/PVC terminal box of required size not less than 1.0 mm thick factory made duly painted inside & outside with two coats of black bituminous paint over & including a coat of red oxide primer, with 3 mm thick top cover of plastic laminated sheet of required colour for mounting switch, sockets, fan regulator etc including 2.5 Sqmm FR type PVC insulated unsheathed cable solid copper conductor as continuous earth wire and connected to earth dolly as required at site& including chases cutting & making good disturbed surface & applying finishes to match existing surface complete all as specified and directed.

M&L sub main wiring with two single core PVC insulated & unsheathed cable 6.0 Sqmm (nominal area) FRLS type having multi-stranded copper conductor drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring with and including one 6.0 Sqmm FRLS type PVC insulated unsheathed cable solid copper conductor as earth wire connected to common earth as per IS & cutting chasing for conduit & sinking for boxes & making good to walls disturbed surface & applying finishes to match existing surface complete including taking down of existing sub main wiring complete all as specified and directed. NOTE : Two runs of 6 Sqmm and one run of 6.0 Sqmm cable and PVC conduit shall be measured as a one unit length.

S & F for switch piano, flush type, 5/6 amps, single pole , one way , 230 volt complete all as specified and directed.

S & F for switch piano, flush type, 5/6 amps, single pole , two way , 230 volt complete all as specified and directed.

S & F bell push switch 5 Amp flush type complete all as specified and directed.

S & F for 5 pin, 5/6 Amp , socket outlet, flush type, 2 in 1 complete all as specified and directed.

S & F for bell, ding- dong , AC, 230 Volt, single pole complete all as specified and directed.

S&F lamp holder PVC/Polycarbonate type with cord grip cap/back plate suitable for batten/angle /pendent fitting complete all as specified and directed.

S&F LED retrofit lamp of capacity 12/15 watt, B-22 holder base with polycarbonate body and aluminium heat sink warm white complete including taking down old/ unserviceable CFL/bulb complete all as specified and directed.

S&F switch socket combination 2 in 1, 6 pin 16Amps multipurpose type 240 volts complete all as specified and directed.

S&F ceiling rose single phase, PVC poly carbonate, insulated body three terminals ISI marked complete all as specified and directed.

S& F for sheet metal enclosure factory made (DB's) for MCBs, double door, SPN 8 ways, 240 Volts with 200 Amp rated bus bars including taking down existing unserviceable DBs (with MCBs) complete all as specified and directed.

S&F Isolator/MCB SP 240 Volt 6 To 32 Amp ISI marked conforming to 'B" curve, breaking capacity 10 KA complete all as specified and directed.

S&F Isolator SPN 40 amp 30mA for earth leakage. Over load and short circuit protection ISI marked complete all as specified and directed.

S&F sheet metal enclosure (DB) , VTPN, double door 415 Volt with 200 amp rated bus bar complete suitable for 1 x 63Amp MCCB as incomer and MCB SPN as outgoing connection through proper size of lugs and cable glands including taking down existing MCB DBs complete all as specified and directed. Note: MCCB and MCB shall be measured and paid seperatly.

S&F MCCB 63 Amp,4 pole ,415 Volt ISI marked conforming to 'B" curve, breaking capacity 16 KA complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below GL with top edge of plate not less than 1.50 m below normal ground level) connected to galvanised earth lead wire 4.0 mm dia (7.5m) as means of bolts, nuts, check nuts and washer besides brazing at all joints as shown on drawings and including excavation, earth work, GI pipe (ISI mark) light grade 15 mm bore for protection of GI wire from earth electrode to and including the earth test point, supplying and laying charcoal dust, common salt, PCC 1:3:6, type C-1(using 20 mm graded crushed stone aggregate ) chamber and mild steel angle iron frame 40 x 40 x 3 mm and 40 mm thick pre-cast RCC cover 1:2:4 , type B-1(using 20 mm graded crushed stone aggregate ) reinforced with 8 mm dia TMT bars @ 75 mm C/C both ways with mild steel handle 12 mm dia, PGI funnel and wire mesh, 20 mm dia GI pipe light grade(ISI marked) for watering all as shown in electrical plate No 3 of SSR Part-I and connected to earth test point including testing of earthing & dismantling /taking down existing old / unserviceable earthing complete all as specified and directed. (Note:- The rates quoted shall also deemed to include the cost of Earth test point and earth wire and protection pipe up to 7.5 meter beyond the earth plates electrode.)

Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying of cables etc. not exceeding 10 sq m on plan and not exceeding 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Removal of surplus excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

Supplying ,laying, commissioning & testing cross sectional area 25 Sqmm , 3.5 core XLPE cable insulated armoured, electric power cables (heavy duty) 1100 Volts grade with standard aluminium conductor including taking down existing old /unserviceable cable complete all as specified & directed. Note: Excavation & earth work, sand cushioning & Bricks shall be measured & paid separately under respective item

S &F for 50 mm dia GI pipe 'light grade' ISI marked including fittings such as bends, tees, sockets etc fixed on wall/pole or laid in trenches under road crossing/hard standing including taking down existing pipe complete all as specified and directed.

M&L for sand cushioning with dry local sand for cable protecting under ground cable (8 cm before laying the cable and 15 cm after laying the cable) in trenches including punning the sand up to 18 cm thick and consolidated complete all as specified and directed. NOTE : Punned thickness only shall be measured.

Supply and laying dry well burnt locally available brick sub class'B' modular bricks laid flat with width equal to the length of whole bricks over cable as cable protection complete all as specified and directed

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each complete all as specified and directed.

S&F stepped type electronic fan regulator flush type AC 230 volt suitable for any type of ceiling fan complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED integral ultra slim round shape surface mounting high power LED luminaire , dome shape opal diffuser lamp of capacity 18w complete including taking down old/ unserviceable CFL/bulb complete all as specified and directed. Make : Orient Cat part No LDSER-18-C

S&F wall lamp/comet wall light unique Aesthetic white colour having suitable holder for B-22 Bulb complete including taking down old/ unserviceable CFL/bulb holder complete all as specified and directed

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete including taking down the existing unserviceable light/mirror fittings complete all as specified and directed

M&L for drilling through bore hole by trenchless technology without disturbing the existing road or hard surface complete all as specified and directed

Supply and fixing ceiling fans complete with blades, down rods and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated complete all as specified and directed

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB single pole 20 Amp complete all as specified and directed.

S&F exhaust fans of metallic body heavy duty AC single phase 230/ 240 V of size 300 mm sweep with bracket, louver shutters, nuts & bolts including connection with PVC copper flexible wire for Exhaust fans complete all as specified and directed.

S & F Building security/street LED light fitting 35 watt IP-65 protection pressure die cast aluminium body ,heat resistant glass ,including driver and making necessary electric connection with 2.5 sqmm twin core copper wire 1.5 long complete fixed in GI pipe fixed to pole complete all as specified and directed. MAKE: Havells Cat Part No. ENDURASUNDOWNSL35WLED765PASYBOPC/ BAJAJ Cat Part No. ENXT P42L WH PO PC SDMT/ SURYA Cat Part No. SLEUL36WIP66(LXN)/ CROMPTON Cat Part No. LSTS-36-CDL-M.

S&F LED luminaire 600mm x 600mm , 35/36Watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor with connector block and making good the disturbed surface complete all as specified and directed. MAKE: HAVELLS Cat Part No. VENUSNEO2X2PLR36WLED865ST/ BAJAJ Cat Part No. BZRSQL43LXEWHODSD/ SURYA Cat Part No. SLEFP36R22/ CROMPTON Cat Part No. LCTLRNE-36-FO-CDL.

S&F isolator/MCB TPN 415Volt 63Amp ISI marked conforming to 'B' curve breaking capacity 10KA complete all as specified and directed.

S&F in repair LED flood light 70 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant with driver and lamp complete all as specified and directed. MAKE: HAVELLS Cat Part No. JETAADORNFLS70WLED757SSYMTOTG/ CROMPTON Cat Part No. LFL-70-CDL/60-M / SURYA Cat Part No. SLE FL 70W IP65 RFLOOD/ ORIENT Cat Part No. LSFS-070-C.

M&L for taking down the existing ceiling fan for servicing, greasing , replacement of bearing, safety pin, canopy, fan condenser, clamp, rubber reel, nut/bolts reqd at site and cleaning and preparing surface, filling cavities with filler including painting with one coat of synthetic paint including down rod of approved white colour and refixing in its original positing and making all electric connection complete all as specified and directed.

Supply and errection of steel tubular pole swaged type 410-SP 31(9.0m long pole) as per IS:2713 (part I to III) 1980 complete with cast iron base plate, pole cap, mild steel bolt, nuts and screws complete including dismantling of existing pole all as specified including consisting of following works:- (a) Excavation in trenches not exceeding 1.5 mtr wide & 1.57 mtr deep for pole foundation & getting out in soft/loose soil, returning filling in the excavated of soil after fixing the pole in foundation ramming earth around in layer not exceeding 25 cm thick and disposal of surplus soil to a distance not exceeding 50 mtrs complete all as specified and directed. (b) M&L for PCC 1:4:8, type D2 (using 40mm graded crushed stone aggregate) in foundation 900mmx600mm cross section and planting depth 1.5 mtr for concrete encasing the pole up to GL complete all as specified and directed. (c) M&L for providing PCC 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) for plinth block/collar above GL 500mm high and 450mm dia complete all as specified and directed.

Contd/... (d) M&L for painting of pole externally with one coat of black bituminous paint (up to planting depth) and above plinth block concrete collar with two coat of aluminium paint over a coat of red oxide primer including preparation of surface including painting of 30 cm wide bands 3 Nos with synthetic enamel paint of appropriate colour in alternate layer up to the height of 1.5mm above plinth block. (e) M&L for writing letter or figures (Block Roman, Italic as Indian) with thick synthetic enamel paint of apprised shade not exceeding 5 cm height including numbering of pole complete all as specified and directed. (f)Removing excavated surplus soil not exceeding 50 Mtr and depositing where directed at a level not exceeding 1.5 Mtr above the starting point complete all as specified and directed. NOTE : Manufacture's test certificate will be produced before execution work.

S&F SMC Junction box with 4 Nos 63 A Aluminium Bus Bar, Din rail for MCB Mounting, inside dimension 250x250x160mm complete all as specified and directed . Make- Sintex Model GSJB 2525

S&F 3 core x 4 sqmm solid, unarmoured Aluminium wire from junction box to street light complete all as specified and directed.

S&F single compression Brass Gland of any size as per requirement complete all as specified and directed.

Supplying, laying, commissioning & testing cross sectional area 10 Sqmm , 4 core XLPE cable insulated armoured, electric power cables (heavy duty) 1100 Volts grade with standard aluminium conductor including taking down existing old /unserviceable cable complete all as specified & directed. Note: Excavation & earth work, sand cushioning & Bricks shall be measured & paid separately under respective item

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below GL with top edge of plate not less than 1.50 m below normal ground level) connected to galvanised earth strip 25x4mm as means of bolts, nuts, check nuts and washer besides brazing at all joints as shown on drawings and including excavation, earth work, GI pipe () light grade 15 mm bore for protection of GI wire from earth electrode to and including the earth test point, supplying and laying charcoal dust, common salt, PCC 1:3:6, type C-1(using 20 mm graded crushed stone aggregate ) chamber and mild steel angle iron frame 40 x 40 x 3 mm and 40 mm thick pre-cast RCC cover 1:2:4 , type B-1(using 20 mm graded crushed stone aggregate ) reinforced with 8 mm dia TMT bars @ 75 mm C/C both ways with mild steel handle 12 mm dia, PGI funnel and wire mesh, 20 mm dia GI pipe light grade(ISI marked) for watering all as shown in electrical plate No 3 of SSR Part-I and connected to earth test point including testing of earthing & dismantling /taking down existing old / unserviceable earthing complete all as specified and directed. (Note:- The rates quoted shall also deemed to include the cost of Earth test point and earth wire and protection pipe up to 7.5 meter beyond the earth plates electrode.)

Supply and fix LED street light luminaires 45 watt with pressure aluminium -die- cast powder coating housing & frame with heat resistant, high efficiency toughened glass with EPDM gasket for IP66 protection complete assembly with LED ,driver& accessories pre-wired-up to terminal block including connection on pole or building including taking down of old /unserviceable street light fitting complete all as specified and directed. MAKE: HAVELLS Cat Part No. ENDURASUNDOWNSL45WLED765PASYBOPC/ BAJAJ Cat Part No. ENXT P54L WH PO PCSD MT/ CROMPTON Cat Part No. LSTS-45-CDL-M/ SURYA Cat Part No. SLE UL 45W IP66 (LXN).

M&L for GI bracket for security light & street light fittings fabricated with GI tubing 40 mm dia 'medium grade' 1.2 m long including and bending to angle of 120 degree fixed in repair complete all as specified and directed.

M&L for mild steel clamp fabricated with mild steel flat iron 50 x 6 mm including nut and bolts with washer suitable for fixing of GI bracket on PCC/ steel poles fixed in repair complete all as specified and directed.

Supply and fix in repair Electronic street light Astronomical control timer switch, operating automatic/ manually with sheet metal enclose box wall/pole mounting type including heavy duty clamp made out of mild steel sheet 3.15 mm thick duly painted with two coat of synthetic enamelled paint over a coat of red oxide primer of capacity 6 KW, Conforms to IS/IEC 60947-4-1, 3 phase, 415 volts, 50 Hz, ISI marked suitable to accommodate the following including taking down existing feeder box :- (a) Three phase control switch MCB TPN 40A 10 KA - 01 No (Incoming) (b Auto/Manual control switch (c) Heavy duty 3 Phase Contactor 40 Amp ML-3 with axillary contact - 01 No. (d) Astronomical Timer Switch- 01 No. Make - Havells cat Part No - IHXTS0306A or equivalent make in L&T, Legrand

Supply, install, testing and commissioning of servo controlled Voltage stabilizer 100KVA (conforming to BIS 9815:Part 1:1994) three Phase ,50 Hz, Naturally Oil cooled, for automatic operation, copper wound, indoor type, unbalanced type, metallic body Powder coated with lifting hooks 4 Nos ,digital Display type ,relay free smooth and silent operation with 1st filling of Transformer oil (ISI Marked) up to level having following specification:- (a) input variation between 300 V to 480 V (b) output voltage stabilized at 415 with accuracy ± 1% (c) Rated Frequency 50 Hz (d) No Distortion in wave form (e) Response time not to exceed 20 mille second (f) Rate of correction 8 volt/second for single phase and 13 v/second for phase to phase (g) Efficiency more than 95% (h) Type of load : Three phase ,unbalanced type (j) Digital Display Voltmeter/Ammeter. (k) Overload short circuit protections, High/low voltage cut off, bypass arrangement in case of emergency (l) Single phase sequence change protection.

M&L for rubber insulating matting as per ISI Mark (size 1m x 2m x19 mm) for voltage up to 11 KV complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70 sq mm 3.5 core complete all as specified and directed.

M/S DEEKSHA CONSTRUCTION

M/S SWATI CONSTRUCTION