IMPROVEMENT TO NC (E) QTRS AT 12BRD AND PROVN OF CERTAIN B/R and E/M WORKS AT MI ROOM AT 12 BRD UNDER GE (AF) TUGHLAKABAD

Amount

Taking down Cement plaster including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by Engr-in-charge.

M&L Rendering 15mm thick in cement mortar (1:6) on other than fare face of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L Rendering 5mm thick in cement mortar in (1:3) on ceiling complete all as specified and directed by Engr-in-charge.

M&L for applying 2 coats of OBD on new surface of walls over 3mm thick wall care putty complete all as specified and directed by Engr-in-charge.

M&L for preparation of new undecorated surfaces and apply three coat of white wash on ceiling, complete all as specified and directed by Engr-in-charge.

M&L for 15mm thick rendering in cm (1:4) on fair faces of brick or concrete surfaces finished even and smooth complete without using extra cement complete all as specified and directed by Engr-in-charge.

M&L two coats of cement based paint on new surfaces of walls including preparation of surfaces complete all as specified and directed by Engr-in-charge.

Dismantling of old brick tiles or terracing tiles, single layer on roofs complete all as specified and directed by Engr-in-charge.

Surface excavation of concrete from roof n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out from site complete all as specified and directed by Engr-in-charge.

Cutting out cracks to V-section in existing roofs or terracing cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand (1:1) (by weight) complete all as specified and directed by Engr-in-charge.

M&L for PCC (1:2:4), type B1 by using 20mm graded stone aggregate in padding/mass concrete and haunching complete all as specified and directed by Engr-in-charge.

M&L 10mm thick rendering in CM (1:4) using water proofing compound at the rate of 3% weight of cement over concrete surfaces complete all as specified and directed by Engr-in-charge.

Supply only water proofing compound complete all as specified and directed by Engr-in-charge.

M&L for APP based polymeric membrane minimum weighing 3Kg/sqm and minimum 3 mm thick reinforced with polyester non wove fabric (wt not less than 150 Gms /Sqm ) land on Providing & laying a coat of cold applied bitumen 85/25 based primer on entire surface @ 0.300 Ltr/Sqm on dry and clean surfaces complete all as specified and directed by Engr-in-charge.

M&L for washed stone grit plaster on exterior walls in two layers under layer 12 mm cement plaster (1:4) (1 cement : 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square meter, top layer 15 mm cement plaster (1: ½ : 2) (1 cement ½ coarse sand : 2 stone chipping 10 mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing the top layer with brushes and water to expose the stone chippings complete all as specified and directed by Engr-in-charge. Note: Payment for providing grooves shall be made separately.

Forming groove of uniform size 15 mm wide and 15 mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens , nailed to under layer including removal of wooden battens repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engr-in-Charge.

Disconnecting existing tanks Exc 250 & N exc 500, setting aside (or lowering if required) for repairs, cleaning, etc and hoisting if required reconnecting and refixing in position complete all as specified and directed by Engr-in-charge. Note: Cleaning repairing etc measured separately.

Disconnecting existing tanks Exc 500 & N exc 1000, setting aside (or lowering if required) for repairs, cleaning, etc and hoisting if required reconnecting and refixing in position complete all as specified and directed by Engr-in-charge. Note: Cleaning repairing etc measured separately.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing unserviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L for 25mm thick cement concrete flooring (1:2:4) type B1 by using 20 mm graded aggregate finished even and fair complete all as specified and directed by Engr-in-charge.

M&L for Screed bed or bedding layer of mortar 15 mm thick in CM (1:6) for laying floor finishes complete all as specified and directed by Engr-in-charge.

M&L for Non-skid joint free ceramic coloured printed tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engr-in-charge.

M&L for rendering 10 mm thick in CM (1:3) finished even and fair as on brick or concrete surfaces for laying wall tiles complete all as specified and directed by Engr-in-charge.

M&L for colour joint free Glazed ceramic tiles in vertical surface 350x250x7mm/ 450x350x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed by Engr-in-charge.

M&L for Dark Shade Vitrified ceramic tiles 10 mm thick (Square/rectangular) polished area of each tiles not exc 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement complete all as specified and directed by Engr-in-charge.

Demolition of cement concrete reinforced in any position incl cut of bars as required complete all as specified and directed by Engr-in-charge.

M&L for reinforced cement concrete (1:2:4) type B1 using 20mm graded crushed stone aggregate as in chajjas complete all as specified and as directed by Engr-in-Charge.

M&L for Reinforced cement concrete (1:2:4) type B1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engr-in-charge.

M&L for Form work to soffits of suspended slab such as roof slab, floor slab etc n exc 200 mm thick rough finished surface of concrete slab complete all as specified and directed by Engr-in-charge.

M&L for rough finished surfaces if concrete formwork to sides and soffits if floor or roof beams haunching girder bressummer chajja shelves including supports complete all as specified and directed by Engr-in-charge.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-charge.

All as per sl item No 31.00 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed by Engr-in-charge.

Demolition of cement concrete (un reinforced) in ground floors and pavings exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engr-in-charge.

M&L for 100mm thick cement concrete (1:2:4) type B2 using 40mm graded aggregate as in path/ plinth protection finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Eng-in-charge. (25+6)

M&L for 100 mm thick PCC (1:4:8) type B2 using 40 mm graded crushed stone aggregate as in PCC hard standing, finish the surfaces even and smooth without using extra cement complete all as specified and directed by Engr-in-charge. (250+40)

Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engr-in-charge.

M&L for Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm m thickness, M-35 grade With grey cement and no pigment complete all as specified and directed by Engr-in-charge.

M&L for cement concrete chequered tiles 20cmx20cmx25mm thick set & jointed with cement mortar (1:3) & pointed in neat cement slurry with grey cement and pigments including 20 mm thick screed bed in cm (1:6) complete all as specified and directed by Engr-in-charge. (50+40) Make :- Coral/Terra ferma/Ultra

S&F in repairs of stainless steel kitchen plate rack of size 24"x30" on walls complete all as specified and directed by Engr-in-charge.

Taking down chowkats or frame with shutter (without taking out shutter from the frame) not exceeding 1.50 Sqm each as doors, windows & ventilators etc. and removal from site complete all as specified and directed by Engr-in-charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing and as directed by Engr-in-Charge

S&F for 30 mm thick factory made solid panel PVC door shutter confirming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 gauge thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C' channel of size 30x50mm forming styles and 5mm thick 75mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail panelling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete as per manufacturers specifications & drawings ass as directed by Engineer-in-Charge.

S&F in repair Stainless steel wire cloth, (grade 304) 0.36 mm dia of wire and average width of aperture 1.4 mm and fixed with tinned stacks, or galvanized wire staples complete all as specified and directed by Engr-in-charge.

S&F of 150 mm mild steel barrel tower bolts stove enamelled black with bright bolt and fixed complete all as specified and directed by Engr-in-charge.

S&F mild steel pressed handle 150 mm long oval types stove enameled black complete all as specified and directed by Engr-in-charge.

S&F in repairs of 75mm butt hinges extruded brass, with mild steel hinge pin, bright polished and fixed, type B-12 complete all as specified and directed by Engr-in-charge.

S&F in repairs of 150 mm mild steel barrel tower bolts stove enamelled black with bright bolt and fixed complete all as specified and directed by Engr-in-charge.

M&L for bricks works with sub class "B" bricks straight or curved on plan exc 6m mean radius built in CM (1:4) complete all as specified and directed by Engr-in-charge.

M&L for rendering 15mm thick in cm (1:6) on fair faces of brick work or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed.

M&L for two coat with distemper oil emulsion over a coat of primer on new plastered surface on wall complete all as specified and directed by Engr-in-charge.

M&L for Excavating in post holes (or similar holes) for hard and dense soil each n exc 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed by Engr-in-charge.

M&L for Cement concrete (1:4:8) type C2 using 40 mm graded stone aggregate for filling and mass concrete complete all as specified and directed by Engr-in-charge.

S&F roof trusses Fe 410-W (Grade E-250) quality-A (framed), trussed, purling, wind tie, crane gentries and rail and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections )including distance pieces, cleats etc complete all as specified and as directed by Engr-in-Charge.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed by Eng-in-charge.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Eng-in-charge.

S&F 0.56 mm Plain, Aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed) complete all as specified and directed by Eng-in-charge.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed by Engr-in-Charge.

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed by Engr-in-charge.

S&F for anodised aluminium frame (minimum 50 micron powder coating) for doors windows ventilators with one or more rebates including cleat for fixing etc complete all as specified and directed by Engr-in-charge.

S&F aluminium powder coated of any colour (thickness or powder coating not less than 50 micron) windows and ventilator shutters with aluminium grill side hung type without sash bars aluminium section weighing 0.55KG/Sqm including necessary jointing cleats glazing clips rubber packing anodised snap beading screws anodised aluminium fitting such as peg stay 150 mm long (01 No) hinges type B2 100 mm long(02 No) suitable handle (01 No) complete all as specified and directed by Engr-in-charge.

S&F 12mm thick prelaminated particle board interior grade prelaminated both side with decorative choice lamination fixed with screws to timber frame work or as in cubical, partition or cupboards, complete all as specified and directed by Engr-in-charge.

S&F double action floor spring hydraulically regulated made up of aluminium 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed by Engr-in-charge.

S&F 4 lever brass mortice lock, vertical type, size 100 mm complete all as specified and directed by Engr-in-charge.

S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr-in-charge.

M&L for false ceiling of approved (ISI marked) make with 4mm thick HPS board fixed to Anodised aluminium snap grid frame work for false ceiling grid 605x605mm size suspended system fixed to MS framed work of approved make and section as specified in SSR Part I with suitable hook/fasteners and GI/almn suspenders not less than 3mm dia @ 1.00m C/C minimum. ceiling system is to be fixed in water level without any sag complete all as specified and directed by Engr-in-charge.

M&L for Light Shade Vitrified ceramic tiles 10 mm thick (Square /rectangular) polished area of each tiles not exc 0.36 Sqm over 15mm thick screed bed in CM (1:6) as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement complete all as specified and directed by Engr-in-charge.

M&L complete for wiring with cable of size 1.5 sqmm single core copper multistrand conductor including continuous earth wire, using cable FRLS insulated(unsheathed) 1100 volts grade conforming to Is-694 drawn in to and including concealed PVC rigid conduit medium duty with all fittings and fixing accessories ISI certified IS 9537 part -3 and terminated in to pressed steel metal flush boxes suitable for modular accessories and including modular cover plates with frame for mounting switches, socket regulator, brackets etc and including necessary cement work including cutting chases pinning in making good to facing and pointing in cement mortar (1:3) to the ends or cutting chases for concealed conduit point wiring and making good disturbed surface complete all as specified and directed by Engr in charge for followings Note: Cutting not exc 4cm girth and 4cm width:-

One light / fan point controlled by one, one way switch. (11+30)

One 3 pin socket out let 5 amps independent. (3+15)

One 5 pin, 5 amps socket point in same board with other switches. (1+15)

M&L for one 3 pin socket out let 15 amps independent but with cable of size 4.0 Sqmm in point wiring and 4.0 Sqmm in continuous earth wire with necessary accessories complete all as specified and directed by the Engr-in-charge. (4+15)

M&L Complete For modular switch one way 6 amps 1 module complete all as specified and directed by the Engr-in-charge.

M&L Complete For modular switch one way 16 amps 1 module complete all as specified and directed by the Engr-in-charge.

M&L Complete for modular socket 2 in 1, 5 pin 6 amps 2 module complete all as specified and directed by the Engr-in-charge.

M&L Complete for modular socket 2 in 1, 6 pin 6A/16 amp 2 module complete all as specified and directed by the Engr-in-charge.

S&F complete for modular metal flush box 2 module including cutting of chassis and making good disturbed surfaces and rate deemed to be included in quoted rate complete all as specified and directed by the Engr-in-charge.

S&F complete for modular metal flush box 6 module including cutting of chassis and making good disturbed surfaces and rate deemed to be included in quoted rate complete all as specified and directed by the Engr-in-charge.

S&F complete for modular white cover plate with frame 2 module complete all as specified and directed by the Engr-in-charge.

S&F complete for modular white cover plate with frame 6 module complete all as specified and directed by the Engr-in-charge.

M&L complete for ceiling rose surface Bakelite 3 terminal complete all as specified and directed by the Engr-in-charge.

M&L complete for sub main wiring with single core copper multi strand conductor FRLS flexible insulated (unsheathed) cable of size 2x04 Sq mm and 1x 4.00 Sq mm as in continuous earth wire drawn into & including PVC casing capping not less than 25mm dia ISI marked complete with fittings and fixings accessories laid complete all as specified and directed by the Engr-in-charge.

M&L for Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB single pole 20 amp complete all as specified and directed by the Engr-in-charge.

M&L complete for pvc/polycarbonate type Lamp holder, insulated body, with back plate for batten fittings complete all as specified and directed by the Engr-in-charge. (2+30)

S&F energy saving LED lamp 15 Watt, 230 volts 50 Hz complete all as specified and directed by the Engr-in-charge.

S&F for LED lights fitting 1x 16W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by the Engr-in-charge. Make: Phillips / CG / Havells

S&F for ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE Five star rated with brushless direct current motor (BLDC) including necessary finishing complete all as specified and directed by Engr-in-Charge. Make: Usha / CG / Orient

Supply and install hi wall split units indoor/outdoor complete with cordless remote control unit and within built air ionizer and Plasma filter for better indoor air quality of capacity 2 TR including connections complete all as specified and directed by Engr-in-Charge. Make : O General / Voltas / Hitach

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type and designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of + 2.5 % and capacity 5 kVA complete all as specified and directed by Engr-in-Charge. Make: V-Guard / Microtek / Everest

M&L for Switch piano, flush type single pole, one way 5 Amp complete all as specified and directed by the Engr-in-charge.

M&L for Switch piano, flush type single pole, one way 15 Amp complete all as specified and directed by the Engr-in-charge.

M&L for Socket outlet 2 in 1, 3 pin, 5 Amp complete all as specified and directed by the Engr-in-charge.

M&L for Socket outlet 2 in 1, 3 pin, 5 and 15 Amp flush type complete all as specified and directed by the Engr-in-charge.

M&L for stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as required complete all as specified and directed by the Engr-in-charge.

S&F energy saving LED lamp 9 watt, 230 volts 50 Hz complete all as specified and directed by the Engr-in-charge.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc. complete all as specified and directed by the Engr-in-charge.

M&L for grade galvanised medium grade of 15 mm dia, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by the Engr-in-charge.

S&F for SP 5 to 32 Amp 240V, 10KA 'C' curve miniature circuit breaker (MCB) in the MCB DB complete with connection testing and commissioning complete all as specified and directed by the Engr-in-charge.

MOHIT ENTERPRISES

Balaji Constructions

M/S RK Builders