Loading…
Loading…
Tender Value
₹4.0 Cr
EMD Value
₹8.1 L
Closing Date
3 Jul 2026, 3:00 pm3d left
Similar tender results from the same govt authority in the past 3 years.
At TSK Division- Extension of PF No. 1 by 220 m at LLO and PF No. 2 by 200 m at MJN in connection with ABSS.
02-TSK-ENGG-28-2026
02-TSK-ENGG-28-2026
Open
12 Months
Unknown (Unspecified Location)
₹0
₹8.1 L
12 Jun 2026
12 Jun 2026
19 Jun 2026
No. 2 by 200 m at MJN in connection with ABSS.
Item- 2 CPWD ITEMS
S No. Item No Description of Item Unit Qty Rate Amount
4.0 CONCRETE WORK
4.1S CEMENT CONCRETE (CAST IN SITU)
Providing and laying in position cement
concrete of specified grade excluding the cost
of centering and shuttering - All work up to
derived from natural sources : 4 graded stone
aggregate 20 mm nominal size derived from
natural sources)
5.0 REINFORCEMENT CEMENT CONCRETE
5.1S CAST IN SITU
Providing and laying in position specified
grade of reinforced cement concrete,
5.1 excluding the cost of centering, shuttering,
finishing and reinforcement - All work up to
derived from natural sources : 3 graded stone
aggregate 20 mm nominal size derived from
natural sources)
Reinforced cement concrete work in walls (any
thickness), including attached pilasters,
buttresses, plinth and string courses, fillets,
5.2 columns, pillars, piers, abutments, posts and
struts etc. above plinth level up to floor five
level, excluding cost of centering, shuttering,
finishing and reinforcement :
derived from natural sources : 3 graded stone
aggregate 20 mm nominal size derived from
natural sources)
5.9S FORM WORK
Centering and shuttering including strutting,
propping etc. and removal of form for
5.9.1 Foundations, footings, bases of columns, etc. Sqm 391 392.15 153330.65
for mass concrete
5.9.2 Walls (any thickness) including attached Sqm 2140 842.5 1802950
5 pilasters, buttresses, plinth and string courses
5.22S STEEL REINFORCEMENT
Steel reinforcement for R.C.C. work including
straightening, cutting, bending, placing in
position and binding all complete upto plinth
5.22.6 Thermo-Mechanically Treated bars of grade Kg 25000 107.85 2696250
Fe-500D or more.
Steel reinforcement for R.C.C. work including
straightening, cutting, bending, placing in
position and binding all complete above plinth
5.22A.6 Thermo-Mechanically Treated bars of grade Kg 34200 107.85 3688470
Fe-500D or more.
6.0 MASONRY WORK
6.1S General
Brick work with common burnt clay F.P.S. (non
6.1 modular) bricks of class designation 7.5 in
foundation and plinth in:
8.0 CLADDING WORK
TINSUKIA DIVISION-ENGINEERING/N F RLY
8.1S General
Providing and fixing 18 mm thick gang saw
cut, mirror polished, premoulded and
prepolished, machine cut for kitchen
platforms, vanity counters, window sills, facias
and similar locations of required size,
approved shade, colour and texture laid over
20 mm thick base cement mortar 1:4 (1
cement : 4 coarse sand), joints treated with
white cement, mixed with matching pigment,
epoxy touch ups, including rubbing, curing,
moulding and polishing to edges to give high
gloss finish etc. complete at all levels
Granite stone slab colour black, Cherry/Ruby
10.0 STEEL WORK
10.1S General
Steel work in built up tubular (round, square or
rectangular hollow tubes etc.) trusses etc.,
including cutting, hoisting, fixing in position
and applying a priming coat of approved steel
primer, including welding and bolted with
special shaped washers etc. complete.
10.28 Providing and fixing stainless steel ( Grade Kg 420 772.4 324408
304) railing made of Hollow tubes, channels,
plates etc., including welding, grinding,
buffing, polishing and making curvature
(wherever required) and fitting the same with
necessary stainless steel nuts and bolts
complete, including fixing the railing with
12 necessary accessories & stainless steel dash
fasteners , stainless steel bolts etc., of
required size, on the top of the floor or the side
of waist slab with suitable arrangement as per
approval of Engineer-in-charge, (for payment
purpose only weight of stainless steel
members shall be considered excluding fixing
accessories such as nuts, bolts, fasteners etc.).
11.0 FLOORING
11.1S General
cement : 2 coarse sand : 4 graded stone
aggregate 20 mm nominal size), including
finishing complete.
11.16S TILE FLOORING
Chequered precast cement concrete tiles 22
mm thick in footpath & courtyard, jointed with
neat cement slurry mixed with pigment to
match the shade of tiles, including rubbing and
cleaning etc. complete, on 20 mm thick bed of
cement mortar 1:4 (1 cement: 4 coarse sand).
14 11.20.3 Dark shade pigment using ordinary cement Sqm 380 1119.5 425410
11.26S KOTA STONE FLOORING
Kota stone slab flooring over 20 mm (average)
thick base laid over and jointed with grey
cement slurry mixed with pigment to match
the shade of the slab, including rubbing and
polishing complete with base of cement
mortar 1 : 4 (1 cement : 4 coarse sand) :
11.37S CERAMIC GLAZED TILES
TINSUKIA DIVISION-ENGINEERING/N F RLY
11.40 Providing and laying rectified Glazed Ceramic Sqm 40 1439.4 57576
floor tiles of size 300x300 mm or more
(thickness to be specified by the
manufacturer), of 1st quality conforming to IS :
15622, of approved make, in all colours,
16 shades, except White, Ivory, Grey, Fume Red
Brown, laid on 20 mm thick Cement Mortar 1:4
(1 Cement : 4 Coarse sand), jointing with grey
cement slurry @ 3.3 kg/ sqm including
pointing the joints with white cement and
matching pigments etc., complete.
12.0 ROOFING
12.37S RAIN WATER SPOUT AND PIPE
12.50 Providing and fixing precoated galvanised iron Sqm 60 738.65 44319
profile sheets (size, shape and pitch of
corrugation as approved by Engineer-in-
charge) of total coated thickness 0.50 mm
(base metal of minimum 0.45 mm thickness
with total coating thickness of 0.05 mm) with
zinc coating 120 grams per sqm as per IS:
277, in 240 mpa steel grade, 5-7 microns
epoxy primer on both side of the sheet and
polyester top coat 15-18 microns. Sheet
17 should have protective guard film of 25
microns minimum to avoid scratches during
transportation and should be supplied in single
length upto 12 metre or as desired by
Engineer-in-charge. The sheet shall be fixed
using self drilling /self tapping screws of size
(5.5x 55 mm) with EPDM seal, complete upto
any pitch in horizontal/ vertical or curved
surfaces, excluding the cost of purlins, rafters
and trusses and including cutting to size and
shape wherever required.
13.0 FINISHING
13.1S CEMENT PLASTER (IN FINE SAND)
13.1 12 mm cement plaster of mix :
13.44S EXTERIOR FINISHING
Finishing walls with Acrylic Smooth exterior
paint of required shade :
13.46.1 New work (Two or more coat applied @ 1.67 Sqm 1080 160.6 173448
19 ltr/10 sqm over and including priming coat of
exterior primer applied @ 0.90 litre/10 sqm)
16.0 ROAD WORK
16.1S ROADS
Dry brick pitching half brick thick in drains
16.12 including supply of bricks and preparing the
surface complete :
16.12.1 With common burnt clay F.P.S. (non modular) Sqm 3050 644.05 1964352.5
bricks of class designation 7.5
16.49S MISCELLANEOUS
16.90 Providing and laying tactile tile (for vision Sqm 135 2017.6 272376
impaired persons as per standards) of size
300x300x9.8mm having with water absorption
less than 0.5% and conforming to IS:15622 of
approved make in all colours and shades in for
outdoor floors such as footpath, court yard,
multi modals location etc., laid on 20mm thick
base of cement mortar 1:4 (1 cement : 4
coarse sand) in all shapes & patterns including
grouting the joints with white cement mixed
with matching pigments etc. complete as per
direction of Engineer-in-Charge.
18.0 WATER SUPPLY
18.4S PP-R PIPES
TINSUKIA DIVISION-ENGINEERING/N F RLY
Providing and fixing 3 layer PP-R (Poly
propylene Random copolymer) pipes
confirming to IS 15801, UV stabilized & anti -
microbial fusion welded, having thermal
stability for hot & cold water supply, including
all PP - R plain & brass threaded polypropylene
random fittings and fixing the pipe with clamps
at 1.00 m spacing. This includes testing of
joints complete as per direction of Engineer-in-
Charge. ( Internal Exposed on walls )
Providing and fixing 3 layer PP-R (Poly
propylene Random copolymer) pipes
confirming to IS:15801 UV stabilized & anti -
microbial fusion welded, having thermal
18.6 stability for hot & cold water supply, including
all PP - R plain & brass threaded polypropylene
random fittings, including trenching, refilling &
testing of joints complete as per direction of
Engineer-in-Charge. External work
18.7S C.P.V.C. PIPES
Providing and fixing Chlorinated Polyvinyl
Chloride (CPVC) pipes, having thermal stability
for hot & cold water supply, including all CPVC
plain & brass threaded fittings and fixing the
pipe with clamps at 1.00 m spacing. This
includes jointing of pipes & fittings with one
step CPVC solvent cement and the cost of
cutting chases and making good the same
including testing of joints complete as per
direction of Engineer in Charge. Concealed
work, including cutting chases and making
good the walls etc.
Providing and fixing Chlorinated Polyvinyl
Chloride (CPVC) pipes, having thermal stability
for hot & cold water supply including all CPVC
plain & brass threaded fittings This includes
jointing of pipes & fittings with one step CPVC
solvent cement, trenching, refilling & testing
of joints complete as per direction of Engineer
in Charge. External work
Providing and fixing G.I. pipes complete with
18.12 G.I. fittings including trenching and refilling
etc. External work
18.15S BRASS FITTINGS
Providing and fixing ball valve (brass) of
18.18 approved quality, High or low pressure, with
plastic floats complete :
C.I. SLUICE VALVES/ FIRE HYDRANTS &
TINSUKIA DIVISION-ENGINEERING/N F RLY
Providing and fixing C.I. sluice valves (with
cap) complete with bolts, nuts, rubber
insertions etc. (the tail pieces if required will
be paid separately) :
18.31.1 100 mm diameter
18.31.3 150 mm diameter
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
STDwithPVCon29.01.2026.pdf
ATTACHMENT
ArbitrationAdvancecorrectionslip10.pdf Tender document 2
ATTACHMENT
GCCACSno.11_compressed.pdf
ATTACHMENT
SpecialconditionPlatformwork.pdf
ATTACHMENT
JPOofCablecutting.pdf
ATTACHMENT
ArbitrationAdvancecorrectionslip10.pdf
ATTACHMENT
Download all tender documents and submit your bid