REPAIR MAINT AND IMPROVEMENT OF LT FEEDER PILLER BOX PANELS BUS BAR PANEL LT SWITCH GEAR MCCBs AND OTHER ALLIED WORKS AND REPAIR MAINT OF STREET LIGHTS SECURITY LIGHTS AND ALLIED WORKS UNDER GE EAST MATHURA

Amount

Taking down unserviceable LED street / security /flood light fittings of any type / wattage / make etc fitted on LT poles, High Mast light poles, building etc for repairing including complete dismantling, checking for repair / replacement of unserviceable parts as required and making the LED light fittings operational to give rated illumination by replacing unserviceable spare parts and refixing the same at existing location or any other location as directed at site and making electrical connections with existing wire complete all as directed. Notes - (i). Cost of taking down carefully from existing position after disconnecting electric connections, sealing cable ends, bringing to MES store yard (If required for repair), is deemed to be included under unit rate quoted. (ii) Cost of supply and fixing of major items required to make the lights serviceable shall be measured and paid separately under item No 2.01 to 2.03 of this schedule. (iii). Cost of items or works not mentioned under item 2.01 to 2.03 and however required to make the lights serviceable will be provided by the contractor without any extra cost to the department and cost thereof shall deemed to be included in the unit rate quoted. (iv) Contractor shall be responsible for day to day repair / Maint works as per schedule and as directed by Engr-in-Charge alongwith all necessary required Tool & Plant & vehicle (for timely repair) to make functional all security/street lights at the station.

Supply only following items to be incorporated against item No 1.00 here in before:

Supply only electronic LED driver suitable for LED street light fitting capacity 30/45/60 Watt installed at site of existing make and specification and as directed.

Supply only electronic LED driver suitable for LED street light/flood light fitting capacity 60/90/150 Watt installed at site of existing make and specification and as directed.

Supply only surge protection device suitable for LED Street light/flood light any wattage all as directed.

Note : for 2.01 to 2.03 : - Electronic LED driver should be consist of all safety controll feature like SMPS based constant current supply with lower THD, Output Open / Short Circuit protection, Phase to Phase protection, Over Voltage protection,Surge Voltage protection.

Supply and fixing in replacemnt of sheet moulding compound junction box shock and rust proof, termite resistant, tamper proof , front openable type for single phase, two wire rating of size 250x200x105mm complete with one no. MCB SP 6 Amp including non metallic clamps and GI nut bolts and washers of suitable size and fixed on pole/wall complete all as specified and as directed. Make - Sintex or equivalent in Hensel/ABB / Power System & Controls.

M&L for street light bracket made out of 40mm dia medium grade GI pipe of 1.2m length bent to required shape suitable for fixing street light/security light fitting on Steel tubular pole/RCC pole/building wall including two Nos clamps made out 30mm X 5mm flat with suitable nuts and bolts (clamp type - as per site requirement ) including applying two coats of aluminium paint over a coating of red oxide primer and Taking down of existing unserviceable rusted street light brackets with clamps, nuts and bolts etc complete all as specified and as directed. Make : TATA/JINDAL/PARAKASH/SURYA

Supply and fixing in replacement MS clamps including nuts, bolts and washers made out of MS flat strip 30x5 mm thick including cutting, bending, drilling holes in shape and size as per the pole size and fixing with PCC/steel tubular pole for holding of GI pipe brackets for mounting of street lights complete all as specified and as directed.

M&L for dismantaling of old/unserviceable PCC poles/struts any type and size complete all as specified and as directed.

Supply and fixing in replacement of steel tubular swaged poles with cast iron base plate, finial taper plug, bolts, nuts & washers as per IS 2713 (Part-II) 1980 made out of mild steel tubing, type 410 SP-31 (9.0 metre long) including marking pole No on pole including the following complete all as specified and as directed. Note : (a) Excavation in any types of soil, returning, filling, well ramming and disposal of surplus soil to a distance not exceeding 50m from the starting points. (b) Cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) as in base. (c) Cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in foundation. (d) Cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in coping of size 300x300x300 including necessary form work. (e) Painting of poles with one coat of red oxide primer and two coat of aluminum paint (one coat before fixing and one coat of aluminum paint after fixing) over exposed surface and making alternate colour band & black & yellow colour in 30cm width upto 1.5m from coping & pole and two coats of bituminous paint over embedded portion.

Supply and fixing in replacement of LED street light fitting 35 watt 230V AC Outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver,lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection complete all as specified and as directed. Make : Havells/Bajaj/Crompton/Philips/C&S/Surya.

Supply and fixing in replacement of LED street light fitting 70 watt 230v AC Outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver,lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection complete all as specified and as directed. Make : Havells/Bajaj/Crompton/Philips/C&S/Surya.

Supply and fixing in replacement of LED street light fitting 100 watt 230v AC Outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver,lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection complete all as specified and as directed. Make : Havells/Bajaj/Crompton/Philips/C&S/Surya.

Supply and fixing in replacement of LED street light fitting 120 watt 230v AC Outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver,lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection complete all as specified and as directed. Make : Havells/Bajaj/Crompton/Philips/C&S/Surya.

Supply and fixing in replacement of LED flood light 100 watt 230v AC Outdoor type with thermal management in multiple optics and equipped with IP-66 protection with impact and corrosion resistant complete with driver and lamp complete all as directed at site. Make : Havells/Bajaj/Crompton/Philips/C&S/Surya.

Supply and fixing in replacement of LED flood light 210 watt 230v AC Outdoor type with thermal management in multiple optics and equipped with IP-66 protection with impact and corrosion resistant complete with driver and lamp complete all as directed at site. Make : Havells/Bajaj/Crompton/Philips/C&S/Surya.

Supply and fixing in replacement of Post top lantern LED type 20 Watt 230V AC outdoor type with decorative post top for 360 degree indirect light IP65 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and as directed. Make : Havells/Bajaj/Crompton/Philips/C&S/Surya.

Supply, laying and testing Service line UG cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of following sizes including passing through with HDPE DWC pipe (size not less than 40mm outer dia & 32mm innner dia) for protection of cable with laid in trenches / duct / fixing on walls / poles with suitable fixing clamp / saddle including connecting with suitable lugs, thimble, glands, nuts and bolts and testing complete all as specified and as directed. Make : Havells/Gloster/Polycab/RR Kables/KEI/Finolex Note : DWC HDPE pipe shall be included in quoted rate of item.

16 Sqmm 2 core.

16 Sqmm 4 core.

35 Sqmm 3.5 core.

Excavating in trenches n. exc 1.5m wide and n.exc 1.5m depth for laying of cables, erection of poles,struts, stays etc and getting out in any type of soil all as specified and as directed.

Returning, filling in including spreading, levelling,watering and well ramming excavated any type soil in layers not exceeding 25 cm thick each, filling back in trenches after cables have been laid and tested, poles,stays,struts have been erected and tested complete all as specified and as directed.

Removal of excavated surplus soil any type to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed.

Material and labour for plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates ) as in foundation of existing panel/pole/road cutting, filling of pole etc complete all specified and as directed.

Material and labour for plain cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) for coping & other petty repairs near existing panel area etc including necessary formwork and finished the surfaces fair & even complete all as directed.

S&F in replacement 1100 volts grade heavy duty flat service electric cable with stranded aluminium conductor of size 10 Sqmm twin core, weather proof, PVC insulated with inner sheathing of PVC tape and overall PVC sheathed for providing electrical connections to existing security/street lights complete all as specified and as directed. Make: Havells/RR Kable/Polycab/Gloster/Finolex.

Supply and Fixing in replacement MCB single pole 6 Amp-32 Amp for street light junction box/panel including connection complete all as specified and as directed. Make: Havells/L&T/Legrand/ABB/C&S

Supplying and fixing in replacement MCB single pole 230 volts 50 Hz AC of rating 40 to 63 Amp including connection complete all as specified and as directed. Make: Legrand/Havells/ABB/L&T/C&S

Supply & Fixing Power Contactor 63-80 Amp rating 4 pole including all connected accessories with suitable rating like coil / auxiliary Contact etc) as per site requirement and suitable for street light controll panel with all connection complete all as specified and as directed. Make: L&T/Schneider/Legrand/Siemens.

Supply & Fixing Power Contactor 25 to 40 Amp rating single pole including all connected accessories with suitable rating like coil/auxiliary Contact etc) as per site requirement and suitable for street light controll panel with all connection complete all as specified and as directed. Make: L&T/Schneider/Legrand /Siemens.

Supply & fixing multifunctional digital timer swith with inbuilt function for switching on/off street lights according to the rising/setting of the sun with combination function according to astronomical time and/or fixed preset times complete with all connection to existing panel as per directed & complete testing . Make :- Legrand as per Cat Part No 4126 54 or equivalent in L&T/Havells/Schneider.

Supply & fixing Weather proof flat twin core aluminium conductor cable of size 2.5 Sqmm, 1100 volts grade including dismantling existing unserviceable cable any description and complete all as specified and directed. Make : Havells/Plaza/Finolex/Polycab/KEI

M&L for cutting/Pruning/trimming of tree branches in vicinity of LT over head electric line and to be made free over head line from trees branches for avoid any short circuit between conductor complete including disposal the wastage branches by dumping in low lying area complete all as specified and as directed. Note : (i) Labour / Tools / Ladder / Vehicle for Cutting / Pruning / trimming of tree branches shall be provided by contractor and rate for the same are included in the quoted rate of item.

Supplying and fixing in replacement of MCB TPN 415 Volt volts 50 Hz AC of rating 63 Amp including connection complete all as specified and as directed. Make: Legrand /Havells/ABB/Schneider/HPL/C&S

S&F LT panel out door type made out of CRCA MS sheet of 3.15 mm thick with aluminium busbar, duly powder coated & mounted on angle iron frame made out of size 50x50x6mm, 90cm high consisting of the following accessories complete all as specified and as directed:- (a) MCB TPN 415 volts 63 Amp, 16 KA - 02 Nos. (b) LED indicating lamp set of three - 01 Set (c) Digital voltmeter, Ammeter - 01 Nos complete set. (d) Grouting of panel 60 cm above GL, embedded in coment concrete M-15 grade (Nominal mix) (using 20mm graded stone aggregate up to 30 cm complete all as specified and as directed.

S&F of Aviation obstruction light luminaries fittings having integral LED aviation light comprising of aluminium housing with polycarbonate enclosure at the top of the pole and making necessary electric connection and fixing arrangement of aviation light complete all as specified and as directed. Make : Bajaj Cat Part No BGAV302LED or eqvt in Wipro/Philips/GEC

S&F LED Bollard light fitting made of extruded aluminium with PC diffuser 9 watt complete all as specified and as directed. Make : Surya Cat part No SLE BL 9W-BLK800 or equivelant in Havells/Bajaj/Cromption/C&S

M&L for scraping, scretching, cleaning the old paint, preparation of the surface for repainting. Painting LT Pole 09 Mtr long steel tubular pole with two coats of aluminium paint and writing pole Nos. including applying one coat of cement base paint on PCC muff complete all as specified and as directed.

S&F steel tubes light grade galvanised with all fittings fixed to walls/ under floors/along poles/ road crossing etc of following sizes complete all as directed:- Make : TATA/JINDAL/Prakash Surya.

40mm bore.

50mm bore.

80mm bore

Taking down unserviceable solar street light fittings of any type/wattage/make etc for repairing including checking for repair/repalcement of unserviceable parts as required and making the light fittings operatioal by replacing unserviceable spare parts and refixing the same at existing location or any other location including connection complete all as directed at site by Engr-in-Charge. Note :- (i) Cost of taking down carefully from existing position, bringing to MES store yard(If required for repair), is deemed to be included in this item quoted rates. (ii) Cost of supply and fixing of major items required to make the lights serviceable shall be measured and paid separately under serial item Nos 37.01 to 37.05.

supply only following items to be incorporated against item No 36 here in before:-

Solar panel for generation of solar energy cap 30 watt of existing make and specificans and all as directed.

Maintenance free battery 12 V 15 Ah of existing make and specification all as directed.

Electronic battery charger suitable for 12 V battery 75 Ah of existing make & specifications and as directed.

DC to AC Convertor suitable for 12 V bty of existing make and specifications and as directed.

LED Security light 15w IP 66 pressure die cast aluminium housing and heat resistant toughened glass with light intensity not less than 1500 lumens. Make : Havells/Bajaj/Cromption/Philips/C&S/Surya.

Supplying, laying or fixing or passing through pipe, testing and commissioning XLPE insulated armoured heavy duty electric cable, 1100 volts grade with stranded aluminium conductor of following nominal cross sectional area all as specified and as directed :- Make : HAVELLS/ICC/GLOSTER/POLYCAB/R K KABLE/KEI

10 sqmm 2 core.

16 sqmm 4 core.

25 Sqmm, 4 core

35 Sqmm, 3.5 core

50 sqmm 3.5 core.

70 sqmm 3.5 core.

95 sqmm 3.5 core

120 sqmm 3.5 core

M&L for sand filling in trenches with clean dry fine sand unwashed including gently punning around cables complete all as specified and as directed. Note : For payment punned depth shall be measured as specified.

Supplying and laying reinforced precast concrete cable cover class LV type 1 with flat size 250 mm x 150 mm x 40 mm complete all as specified and as directed.

M&L for cutting wild grass, bushes, creaper, unwanted vegetation from inside/surrounding of E/M installations, near transformers, pole structures etc including cutting creapers from barbed / cattle fencing of the installations as when directed and removing of unwanted material from installation compound and depositing where directed. Note : The item shall be operated maximum three times in entire period of contract in the same installations. Area measured separately each time.

M&L & tools for trimming tree branches upto 100 mm girth of any location around existing HT/LT OH lines giving clearance of 1.5 m on all sides complete all as specified and as directed. Note : Trimming of tree branches irrespective in numbers in each tree shall be measured as one unit).

M&L for earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth strip 32 x 6 mm by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate No 3 of MES Schedule Part-I connected to earthing point and testing on completion with and including PCC pit in mix 1:3:6 type C1 with RCC 1:2:4 type B-1, 40 mm thick cover reinforced with 6 mm dia M.S bars 3 Nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and charcoal filling, necessary excavation and earth work complete all as specified and as directed.

M&L for earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead 4mm dia by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate No 3 of MES Schedule Part-I connected to earthing point and testing on completion with and including PCC pit in mix 1:3:6 type C1 with RCC 1:2:4 type B-1, 40 mm thick cover reinforced with 6 mm dia M.S bars 3 Nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and charcoal filling, necessary excavation and earth work complete all as specified and as directed.

M&L for fabrication of cubical LT panel board outdoor type with double door of size 800x600x300mm made out of 3 mm thick, MS Sheet, dust, vermin and water proof duly supported on 40 x 40 x 6 mm angle iron frame, having locking arrangement at front and opening arrangement from front & rear both duly fitted with compression cable glands for entry & exit of cables, powder coated with two coats and having minimun clearance of 450 mm above ground level complete and comprising of the following : - (a) Panel mounted Multi-function for voltage, current, frequency, power factor and power Type EM-VIFP -01 set (b) Aluminium bus bar -- 03 Nos. For phase of capacity 200 Amp and 1 Nos 200 Amps for neutral, duly taped in colour coded FRP sleeves. (c) Indicating lamps Red, Yellow and blue in colour, LED type complete with lamp holders, 220 volts AC.- 01 Set of 3 (d) Panel wiring with 2.5 Sqmm PVC Sheathed, PVC insulated FR-HR stranded copper conductor cable through MCB DP 10 A mounted on DIN rail. (e) MCCB 63 Amp, 4 Pole, 415 V, 16 KA - 02 Nos. (f) SPN MCB 40 Amp - 02 Nos Make : HAVELLS/L&T/LEGRAND/SIEMEN/SCHNEIDER/C&S

M&L for fabrication of cubical LT panel board intdoor type with double door of size 1700x1200x450mm made out of 2 mm thick MS Sheet, dust, vermin and water proof duly supported on 40 x 40 x 6 mm angle iron frame, having a place to fit 12 Nos Single phase electric mete complete with locking arrangement at front and opening arrangement from front & rear both duly fitted with compression cable glands for entry & exit of cables, powder coated with two coats and having minimun clearance of 450 mm above ground level complete comprising of the following : - (a) Panel mounted Multi-function for voltage, current, frequency, power factor and power Type EM-VIFP -01 set (b) Aluminium bus bar -- 03 Nos. For phase of capacity 200 Amp and 1 Nos 200 Amps for neutral, duly taped in colour coded FRP sleeves. (c) Indicating lamps Red, Yellow and blue in colour, LED type complete with lamp holders, 220 volts AC.- 01 Set of 3 (d) Panel wiring with 2.5 Sqmm PVC Sheathed, PVC insulated FR-HR stranded copper conductor cable through MCB DP 10 A mounted on DIN rail. (e) MCCB 160 Amp, 4 Pole, 415 V , 16 KA - 01 Nos (f) DP RCBO 25 Amp, 100mA,10KA - 12 Nos (g) SPN MCB 10 Amp - 01 No Make for item No (e) to (g) : Havells/L&T/Legrand/Siemen/Schneider/ C&S /HPL

S&F MCCB 4 pole 415 Volts adjustable type 250 Amp, with breaking capacity 25kA Complete all as spccified and as directed. Make : HAVELLS/L&T/LEGRAND/SIEMEN/SCHNEIDER/ABB/C&S/HPL

S&F MCCB 4 pole 415 Volts adjustable type 200 Amp, with breaking capacity 36kA Complete all as spccified and as directed. Make : HAVELLS/L&T/LEGRAND/SIEMEN/SCHNEIDER/ABB/C&S/HPL

S&F MCCB 4 pole 415 Volts adjustable type 125 Amp, with breaking capacity 16kA Complete all as spccified and as directed. Make : HAVELLS/L&T/LEGRAND/SIEMEN/SCHNEIDER/ABB/C&S/HPL

S&F MCCB 4 pole 415 Volts adjustable type 100 Amp, with breaking capacity 16kA Complete all as spccified and as directed. Make : HAVELLS/L&T/LEGRAND/SIEMEN/SCHNEIDER/ABB/C&S/HPL

S&F MCCB 4 pole 415 Volts adjustable type 63 Amp, with breaking capacity 16kA Complete all as spccified and as directed. Make : HAVELLS/L&T/LEGRAND/SIEMEN/SCHNEIDER/ABB/C&S/HPL

M&L for stay assembly complete with MS Stay plate 300x300x6mm thick galvanised stay rod not less than 20mm dia 2.15 m long glavanised stay bow with thimble,stay clamp,earth work,cement work,stay wire,loop insulator complete all as specified and as directed.

Supply and fixing in replacement of LED flood light fitings 120 Watt 230V AC outdoor type with thermal management in multi optics and equipped with IP-66 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and as directed. Make : Syska /surya/philips/crompton/Havells/Bajaj/C&S

Supply and fixing in replacement of LED flood light fitings 200 Watt 230V AC outdoor type with thermal management in multi optics and equipped with IP-66 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and as directed. Make : Syska /surya/philips/crompton/Havells/Bajaj/C&S

M&L for dismantling of old unserviceable aluminium conductor off size from existing overhead line complete all as specified and directed.

S&F LED Bollard flare fitted with low glare diffuser 12 watt with integrated driver with uniform light distribution complete all as specified and directed. Make : Surya Cat part No SLE BL 12W-FLR650 or equivelant in Havells/ Wipro/Bajaj/Philips/Crompton/C&S

M&L for applying one coat of synthetic enamel paint on outer surface of Panel and minor repair of LT Panel including welding work/repair to door/hinges etc as reqd at site complete all as specified and as directed.

M&L for earth pit cover of size 450x450x50mm thick of RCC M-15 Nomnial mix using 20mm graded stone aggregate with MS TMT reinforcement bar of 8mm@ 150mm centre to centre both ways,MS handle 10mm dia made to shape complete all as specified and as directed.

M/S S S CONSTRUCTION

Vijay Electricals

Ms Kamal Kant Agarwal

M/S GUPTA ENTERPRISES