Loading
Loading…
Loading…
Tender Value
₹4.9 Cr
EMD Value
₹9.8 L
Closing Date
24 Aug 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
EAST
14 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N OR 'V' Whichever is less; where. V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per ANNEXURE-XXXIII, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
a)The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii)One similar work costing not less than the amount equal to 60% of advertised value of the tender.
Defination of Similar Work :- Trenching, cable laying, location and signal foundation/ erection/ termination/ wiring in connection with any signalling work. OR Any Indoor or combined indoor/ outdoor signalling including supply, installation, testing and commissioning of relay interlocking (RRI/PI) system for passenger carrying lines.
10 conditions · 3 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Tender document, Scope of work & GCC 2022 are attached with the tender.
Replacement of degraded indoor & outdoor signalling gears in HB/THB/East section of Mumbai Division.
CR-BB-SNT-EAST-2026-80
CR-BB-SNT-EAST-2026-80
Open
Works - General
18 Months
Mumbai, Maharashtra
₹0
₹9.8 L
24 Aug 2026
24 Jul 2026
10 Aug 2026
55 items across 1 schedule · ₹2,56,80,468.22 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Supply of "2 Aspect" Signal Unit inAluminium body without lenses andtransformers or latest complete andto suit LED signal Lamps and suitablefor 140 mm dia post .(Inspection agency Consignee) | Numbers | 5.00 | 53,821 | 2,69,105 |
| 2 | Supply of "4 Aspect" Signal Unit in Alluminium body without lenses and transformers or latest complete and to suit LED signal Lamps and suitable for 140 mm dia post (Inspection agency Consignee) | Numbers | 30.00 | 1,06,914.4 | 32,07,432 |
| 3 | Supply of "Calling On" Signal Unit in Alluminium body without lenses and transformers complete and to suit LED sigal Lamps.(Inspection agency Consignee) | Numbers | 15.00 | 14,254.75 | 2,13,821.25 |
| 4 | Supply of Shunt Signal Position LightType Alluminium complete to be fittedon 140 mm post 2 for dependent typecomplete with signal unit bracket,terminals etc without lenses, lamp, lamp holder, and to suit LED Signallamps.(Inspection agency Consignee) | Numbers | 10.00 | 25,293.75 | 2,52,937.5 |
| 5 | Supply of 1 way Junction Route Indicator in Alluminium body without lenses and transformers complete and to suit LED signal Lamps.(Inspection agency Consignee) | Numbers | 3.00 | 57,760 | 1,73,280 |
| 6 | Supply of 2 way Junction Route Indicator in Alluminium body without lenses and transformers complete and to suit LED signal Lamps.(Inspection agency Consignee) | Numbers | 2.00 | 42,210.4 | 84,420.8 |
| 7 | "Set of glass fuses size: 5 X 20 mm, 250 V AC fast acting glass body with nickel plating, brass cap cartridge fuse conforming to IEC specification No. 60127- 2, consisting of (1) 250 MA glass fuse = 50 Nos. per set. (2) 1 amp glass fuse = 50 Nos. per set. (3) 2 amps glass fuse = 50 Nos. (4) 3 amps glass fuse = 50 Nos. (5) 4 amps glass fuse = 38 Nos. (6) 10 amps glass fuse = 37 Nos. (One set consists of total 275 Nos.) Brand: WICKMANN / RS / FERRAZ / WAGO(Inspection agency Consignee) | Numbers | 10.00 | 6,382.15 | 63,821.5 |
| 8 | Inspiron 27 All-in-OneComputer. 12thGen intel Corei7-12SSU (12 MB cache, 10cores, 12 threads, up to 4.70GHz Turbo). Operating System11 Home signal Language,English. Monitor 17 inch FHD ,Colour: Pearl white Fabric. HardDrive 512 GB Solid State Drive(Boot) with wireless keyboard & mouse Make HP, DELL or LENOVO.(Inspection agency Consignee) | Numbers | 36.00 | 1,35,566.11 | 48,80,379.96 |
| 9 | "Tool kits for for Multi Section Digital Axle counter as per RDSO specification RDSO/SPN/176/2005 (Ver.2) with latest amendment or specifiaction with Supply of tools for mounting and adjustment of track side equipment and standard jig for drilling holes in rail/fixing DPs on rail.All equipment and tools shall be minimum as per OEM's recommended list adequate for installation, day to day maintenance and adjustment of indoor and outdoor gears including kit for making and drilling of holes on rail and as per annexure XXI. (Inspection agency Consignee)" | Numbers | 1.00 | 88,011.28 | 88,011.28 |
| 10 | Supply of True RMS Digital Multimeter,4000 Count, Voltage:1000V AC/DC.Make Fluke 17B+orDI-LOG 9206 or Megger Modelno.AVO410.(Inspection agency Consignee) | Numbers | 20.00 | 10,999.33 | 2,19,986.6 |
| 11 | Fluke Hand Held 100 KHz Digital True RMS Multimeter Fluke 287 or Fluke 289(Inspection agency Consignee) | Numbers | 20.00 | 65,788.99 | 13,15,779.8 |
| 12 | Supply of DC clampmeter FLUKE AC/DC low current model LH-41 or similar(Inspection agency Consignee) | Numbers | 10.00 | 39,824.31 | 3,98,243.1 |
| 13 | "WELD LESS MODULAR TYPE SS MEDUIMSIZE LOCATION BOX, Along with provision of E Type Lock.(Inspection agency Consignee)" | Numbers | 5.00 | 99,868.85 | 4,99,344.25 |
| 14 | "WELD LESS MODULAR TYPE SS POSTBOX LOCATION BOX, Along with provision of E Type Lock.(Inspection agency Consignee)" | Numbers | 5.00 | 93,140.06 | 4,65,700.3 |
| 15 | Supply and Placing of Trunking and Capping (RCC Duct) of500mm Width as per Drg. No. SDO/Cable laying/ 007 , as detailed in document No. RDSO/SI/G/2010 Ver.1.1 orlatest on 'Guidelines on signalling cable laying'(Inspection agency Consignee) | Numbers | 1000.00 | 1,303.56 | 13,03,560 |
| 16 | Supply of HSS straight shank jobber Drill ground flute to IS 5101/DIN 338/ BS 328 ISO of size 7.1 mm of Addison, JK make of similar(Inspection agency Consignee) | Numbers | 300.00 | 162.32 | 48,696 |
| 17 | Battery operated High performance LED area with 3000 lumens output light weight & unbreakable as per specification attached (1) Product specification M18 HAL -+ M18 NRG 502B (2) Article No. 493345123 (3) Battery compatibility all Milwaukee M18 Batteries (4) Battery capacity (Ah) 5.0 (5) Battery type Li ion (6) No of Battery charger supplied 01 No. (7) Full Battey charging time 59 min (8) Max light output 3000/1500/650 (9) Max run time battery 2/4/9 hr. (10) No. of batteries supplied 2 Nos. (11) Voltage (AC) (V) 220-240 (12) Voltage (DC) (V) 18 (13 Wight with battery pack (kg) 3 (14) One year onsite warranty, installation & training free of cost mak Eibenstock/Milwaukee or equivalent. (Inspection agency Consignee) | Numbers | 4.00 | 59,412.96 | 2,37,651.84 |
| 18 | Replacement of old signal unit /signal route of main signal . this would include releasing of old unit from top of signal post erection and mounting of new signal unit over the post .This aiso includes bringing new signal unit from station to site and bring back old unit from site to station.(Inspection agency Consignee) | Numbers | 20.00 | 1,398.87 | 27,977.4 |
| 19 | Refixing of electrical point machines and ground connection. This would include removal of old/existing point machine and fixing of new/overhauled motor . This would also include bringing the new machines from station / central cabin to site and taking the old / released machines from site to station/ central cabin.(Inspection agency Consignee) | Numbers | 15.00 | 4,916.18 | 73,742.7 |
| 20 | Dismantling of existing signalling gears such as 1.CLS unit along with all accessaries, post with base 2.Location boxes & Junction boxes etc from station as decided by site In-charge and transportation of the same to consignee depot.(Inspection agency Consignee) | Numbers | 20.00 | 699.44 | 13,988.8 |
| 21 | Cutting and removal of worn out location box withouth distrubing equipments housed in location box, fixing new moduler location box, as per instruction of side Engg. This include drilling of holes of required size at site with contractors own tools. Moduler location box will be supplied by Railways.(Inspection agency Consignee) | Numbers | 15.00 | 6,196.51 | 92,947.65 |
| 22 | Replacment of old/ wornout ground connections of point machine by removing existing old/wornout ground connections along with P Bracket and fixing of new ground connection along with P brackets. This will also include neccesery adjestment as per instruction of Site Engg.(Inspection agency Consignee) | Numbers | 30.00 | 4,050.49 | 1,21,514.7 |
| 23 | Repairing of location foundation with masonary work. This also includes cleaning the locations, sand filling in the location and plastering inside the location(Inspection agency Consignee) | Numbers | 140.00 | 3,417.76 | 4,78,486.4 |
| 24 | Supply of Smoke detector from RDSO approved firm only, suitable for RAVEL make fire alarm system.(Inspection agency Consignee) | Numbers | 60.00 | 4,504.9 | 2,70,294 |
| 25 | Sealed maintenance free VRLA battery set of 60 cells(stackable), in combination of 55+5 cells for SMPS basedIPS,each cell of 2VVolt/300AH capacity,fullycharged,confirming to RDSOSpc no. IRS S:93/96A amd 1or latest, complete withconnection links and suitabalynumbered in stackable racksalong with the mannuals. (Inspection agency RDSO) | Set | 6.00 | 5,19,314.37 | 31,15,886.22 |
| 26 | Casting of cement concrete toprotect S&T equipments andlaid cables, above pipes etcby concrete mixture ofcement, sand, stone in theratio of 1:2:4 using 25 mmgraded stone aggregate asper instruction of site incharge of railways. Concreteis to be casted with the helpof suitable size shutteringform as per site requirement.Concrete is to be cured forsufficient time as per standardpractices onrailways(Inspection agency Consignee) | cum | 400.00 | 4,587.9 | 18,35,160 |
| 27 | "VENUS ADJUSTABLE SPANNER15"" /375MM PHOSPHATE FINNISH(Venus) Cast Iron conforming toGrade BM 310 of IS :2108- 1977(for light duty wrenches)preferably Drop Forged, Maximumopening of adjustable jaw (min 36mm to 41 mm) + Tolerance(3mm) make Taparia, VENUS, JK.(INDER Normal duty Type APhosphate Coating Adjustablesingle ended open jaw wrench .(Inspection agency Consignee) | Numbers | 15.00 | 781.07 | 11,716.05 |
| 28 | Supply of DPM meter (AC measurements) range 0 to 750VAC operating on 230V AC auxillary suply equivalentto MECO/Rishi orsimilar.(Inspection agency Consignee) | Numbers | 25.00 | 1,009.39 | 25,234.75 |
| 29 | Supply of DPM meter (DC measurements) range 0 to 200VDC operating on 230V AC auxillary suply equivalentto MECO/Rishi orsimilar.(Inspection agency Consignee) | Numbers | 25.00 | 1,009.39 | 25,234.75 |
| 30 | Solid Carbide Coated Drill Dia 7.1mm For Track Drilling Dimensions are Dia 7.1X30X61 Shank - 9mm(Inspection agency Consignee) | Numbers | 80.00 | 1,878.45 | 1,50,276 |
| 31 | Twist Adaptor 19mm weldon for 13 mm (part no. 210245FS(Inspection agency Consignee) | Numbers | 10.00 | 873.81 | 8,738.1 |
| 32 | Drill twist H.S.S. for MORSE taper shank type N dia of drill bit 16 mm to IS 5103 / 1969 with amendement no. 1 to 3.(Inspection agency Consignee) | Numbers | 400.00 | 485.12 | 1,94,048 |
| 33 | Twisted Drill size 13 x 19 mm (Part no. 5223118)(Inspection agency Consignee) | Numbers | 18.00 | 2,570.04 | 46,260.72 |
| 34 | Arrangement of Battery operated RailCore Drill alongwith additional 18 mmTCT Rail Core Drill , Maximum corecutting capacity : 36 mm, Ratedspeed: 250/450 RPM, Battery type:Li-on, Battery voltage: 50 Volt,Battery pack capacity: 4 AH, Numberof Battery supplied: 2 Nos, Number ofCharger supplied: 1 No, Specialdesign pressurized Internal spindlecooling to give maximum life of corecutter and to avoid heating of the rail.Time taken to drill one hole of 32 mmin 60 KG 90 UTS rail section less thanone minute. Time taken to fix themachine on the rail, less than 2minutes and to de-clamp less than 1minute. 34 Number 32 mm diameterhole with full charge batteries (17hole per battery) in 60 Kg 90 UTS railsection. 3 Sets of standard center raildrilling adapters for gauge 90, 52, 49provided along with machine. Weightof machine with battery: 18.5 KG,Make: Eibenstock. Bosch,KPTL((Inspection agency Consignee) | Numbers | 2.00 | 2,09,200.73 | 4,18,401.46 |
| 35 | "Repairing of CO2 Type fireextinguishers of 4.5 KGcapacity with pressure gaugeof various relay rooms with allother accessories(Inspection agency Consignee) | Numbers | 30.00 | 2,634.51 | 79,035.3 |
| 36 | Digital current clamp meter to measure current leaks parasitic draws down to 1 mA and electric load from 1 mA to 100 Amp AC/DC, and voltages from 0 to 600 V AC/DC, small jaw size to measure current in signaling circuits, 4 digit display. make FLUKE/ GTC/KIOCO or superior with better specification mentioned with all accessories like test lead, batteries and carrying case, sample may got approved from consignee before supply.(Inspection agency Consignee) | Numbers | 10.00 | 24,381.82 | 2,43,818.2 |
| 37 | Supply of 110 VDC motor with gear box having IP 67 protection type 160 V AC immunity for Siemens make point machine drg.no. C-RT-PM4-A132-01-06(Inspection agency Consignee) | Numbers | 2.00 | 61,285.41 | 1,22,570.82 |
| 38 | 110 V DC motors with gear box IP 67 type (complete motor should be water proofed ) 400 V AC immunity for Siemens make Point machine drg.no. C-RT-PM4-A132-01- 06(Inspection agency Consignee) | Numbers | 2.00 | 65,205.11 | 1,30,410.22 |
| 39 | 110 V DC motors with gear box IP 67 type (complete motor should be water proofed ) 160 V AC immunity for Electric Point machine (IRS type) as per IRS S37/82(Inspection agency RDSO) | Numbers | 30.00 | 37,760 | 11,32,800 |
| 40 | 110 V DC motors with gear box having IP 67 protection type 400 V AC immunity for Electric Point machine IRS type as per IRS S37/82(Inspection agency RDSO) | Numbers | 10.00 | 40,241.63 | 4,02,416.3 |
| 41 | Silver Superior Aluminium Paint (Berger Make) (Inspection agency Consignee) | Litre | 200.00 | 245.83 | 49,166 |
| 42 | Enamel Black Paint (Berger Make)(Inspection agency Consignee) | Litre | 100.00 | 214.31 | 21,431 |
| 43 | Timing Belt type length 300 width 18mm suitable for Heidz Electrical Lifting barrier in Indian Railways as per RDSO/SPN/180/2005. Make: Heidz, Optibelt 2R, Mecoy.(Inspection agency Consignee) | Numbers | 40.00 | 143.7 | 5,748 |
| 44 | Limit Switch new top roller type with 2 NO+2NC contacts as per RDSO specification no IRS/S-41/70 or Latest amendment suitable for Heidz make electrical lifting barrier of Indian railways. Make: Jay Balaji, L&T, Seimens Make as per firms offer. ( Warranty Period : Upto 12 months from the date of supply).(Inspection agency Consignee) | Numbers | 200.00 | 501.5 | 1,00,300 |
| 45 | " Push Button element: 1NO or 1 NC contact element min. 5 Amps rating with screw type fixing of RDSO approved. Accepted Make/Brand:-HEIDZ.(Inspection agency Consignee)" | Numbers | 200.00 | 236 | 47,200 |
| 46 | Supply of Push Button Actuators. Push Button with screw type fixing of RDSO Approved make. MAKE - HEIDZ or Equivalent Firm's Offer-Make/Brand-Heidz(Inspection agency Consignee) | Numbers | 200.00 | 141.6 | 28,320 |
| 47 | 3 pole power contactors with coil voltage suitable for 110VAC coil with minimum 9A current rating , inbuilt 1NO+1NC auxiliary contacts suitable for use in Indian Railway Electrically operated gates. Make: Schneider, L&T, Siemens, Havells. (Shop No.09) (Inspection agency Consignee) | Numbers | 200.00 | 763.46 | 1,52,692 |
| 48 | "Rotary Switch (Change over programme with OFF) suitable for 10A / 440V AC / 2 Pole / 2 way / Two position ON, Two position OFF, 90 degree apart with complete rotation, FLAG Knob. similar to Salzer make Cat No. S10- 61153-B13.(Inspection agency Consignee)" | Numbers | 200.00 | 362 | 72,400 |
| 49 | Limit Switches with 1NO+1NC, Operating at 415V,50HZ,AC15/DC13,Thermal current 10 A 240V AC/30V DC impulse Voltage 1.5KV IS/IEC60947PT-5,CE Marked with ISI Marked IP67,Model No- 60987 of MakeGIC or Similar. (Inspection agency Consignee) | Numbers | 100.00 | 725 | 72,500 |
| 50 | Supply of DWC/HDPE pipe with one snap fit coupler 'O' ring confirming to IS 14930 (Part 2: 2001) Non metallic, normal duty, pliable with protection against chemical attack and fire resistant, anti rodent, in 6 meter length of size 50 mm inner dia.(Inspection agency Consignee) | Metre | 150.00 | 389.76 | 58,464 |
| 51 | Supply of copper lugs 25 Sq.mm double hole for AFTC track lead (Railside) as per Drg.No. R-ST 11788 make Braco.Dowells,Shakti , Ascon.(Sample to be approved before bulksupply).(Inspection agency Consignee) | Numbers | 5000.00 | 26.59 | 1,32,950 |
| 52 | "DEFLECTOR PLATE COMPATIBLE WITH 60 KG RAIL WITH ALL HARDWARE ACCESSORIES FOR USE WITH DIGITAL AXLE COUNTER AS PER RDSO/SPN/177/2012 Version 3.0 or latest. 1 Number DEFLECTOR PLATE means 1 pair DEFLECTOR PLATE protecting one DP from both side.(Inspection agency Consignee)" | Numbers | 360.00 | 4,366 | 15,71,760 |
| 53 | PAINT READY MIXED RED OXIDE (ISC 446) BRUSHING,FINISHING GLOSSY FOR GENERAL PURPOSE TO RDSOSPECN.M &C/PCN/ 122/2020 (REV.1), WITH RDSOAMENDMENT 1B OF SEPTEMBER 2020 PACKED IN NEW ANDSOUND NON RETURNABLE M.S DRUMS TOSPECN.IS:2552/89 Gr.B2(Inspection agency Consignee) | Litre | 250.00 | 89.63 | 22,407.5 |
| 54 | WHITE PAINT Brand : Asian(Inspection agency Consignee) | Litre | 250.00 | 328 | 82,000 |
| 55 | Maintenance card with non stick plastic pocket cover as per propfarma attached in size 18.5 cm x 11.8 cm (Sample will be approved by consignee before bulk supply) (Inspection agency Consignee) | Numbers | 50000.00 | 10.4 | 5,20,000 |
| Schedule total | ₹2,56,80,468.22 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
FINALNEWTENDERDOC2026-802.pdf
ATTACHMENT
GCC_April-2022.pdf
ATTACHMENT
CORRECTIONSLIP1to11GCC2022_compressed.pdf GCC CORRECTION SLIP 1 TO 11
ATTACHMENT
CORRECTIONSLIP1to11GCC2022_compressed.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .