DEVELOPMENT OF ASSAM AGRICULTURAL UNIVERSITY CONSTRUCTION OF TWO NUMBERS LECTURE/EXAMINATION HALLS AT BISWANATH COLLEGE OF AGRICULTURE, BISWANATH CHARIALI

Amount

Civil Works:Demolishing RCC work manually or mechanically means including stacking of steel bars and disposal of unserviceable materials within 50 metre lead as per direction of Engineer-in-charge

Demolishing brick work manually or mechanically means including stacking of steel bars and disposal of unserviceable materials within 50 metre lead as per direction of Engineer-in-charge (15.7.4) In cement mortar

Earthwork in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sq.m on plan) including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. (2.8.1) All kinds of soil

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with local sand, with common burnt clay non modular bricks.

Brick work with common burnt clay modular bricks of class designation7.5 in foundation and plinth in: (6.2.2) Cement mortar 1:6 (1cement:4 coarse sand)

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20cm in trenches, plinth, sides of foundation etc. complete

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work up to plinth level (4.1.11) 1:5:10 (1 cement : 5 fine sand derived from natural sources :10 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement- All work up to plinth level: (5.1.2) 1:1.5:3 (1cement:1.5coarse sand (zone-III):3 graded stone aggregate 20mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement: (5.2.2) 1:1.5:3 (1cement:1.5 coarse sand (zone-III): 3 graded stone aggregate 20mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 deg landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair case cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1cement:1.5 coarse sand (zone-III):3 graded stone aggregate 20mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for (5.9.1) Foundations, footings, bases of columns, etc for mass concrete

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. (5.22.6) Thermo-Mechanically Treated bars of grade Fe-500D or more

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. (5.22A.6) Thermo-Mechanically Treated bars of grade Fe-500D or more

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in super structure above plinth level up to floor V level (6.13.2) Cement mortar 1:4 (1cement:4 coarse sand)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Providing and fixing UV stabilised fibreglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia…...(12.47.2) 2mm thick flat

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50mm(+0.05%) total coated thickness with zinc coating 120 grams per sqm as per IS:277, in 240mpa steel grade, 5-7 microns, epoxy primer on both sides of the sheet and polyster top coat 15-18 microns

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50mm(+0.05%) total coated thickness with zinc coating 120 grams per sqm as per IS:277, in 240mpa steel grade, 5-7 microns, epoxy primer on both sides of the sheet and polyster top coat 15-18 microns using self drilling/self tapping screws complete. (12.51.1) Ridges plain (500-600mm)

12mm cement plaster of mix: (13.1.1) 1:4 (1cement:4 fine sand)

Providing and laying ceramic glazed floor tiles of size 300mmX300mm (thickness to be specified by the manufacture) of 1st quality conforming to IS 15622 of approved make in colors such as White, Ivory, Grey, Fume Red Brown laid on 20mm thick cement mortar 1:4 jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc, complete

Providing and laying vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved brand and manufacture, in all colors and shade laid on 20mm thick cement mortar 1:4 jointing with grey cement slurry@ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done through notch trowel, plier, wedge, clips of required thickness, levelling system and rubber mallet for placing the tiles gently and easily. 11.41A.1 Double charge vitrified tile polished finish of size. 11.41A.1.1 Size of tile 600mmX600mm

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277…............(12.45.1) 12.5mm thick tapered edge gypsum plain board conforming to IS 2095 Part I

Providing and fixing M.S. grill of required pattern in frames of windows etc with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete (9.48.1) Fixed to steel windows by welding

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6mm thick clear float glass both side, having 12mm air gap, including providing EPDM gasket, perforated aluminium spacers, desicants, sealant (Both primary and secondary sealant) etc as per specifications, drawings and direction of Engineer-in-charge complete

Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary screws etc complete (21.15.2) Powder coated minimum thickness 50 micron aluminium

Providing and fixing aluminium round shape handle of outer dia 100mm with SS screws etc. complete as per direction of Engineer in charge (21.16.3) Polyster powder coated minimum thickness 50 micron aluminium

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give even shade: (13.60.1) Two or more coats on new work

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives (13.48A.1) New work (Two or more coats applied @1.43 litre/10sqm. Over and including priming coat of exterior primer applied @0.90 litre/10sqm

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or dash fastener shall be paid for separately) (9.1.3) Kiln seasoned and chemically treated hollock wood

Providing and fixing ISI marked flush door shutters conforming to IS:2202 (Part-I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of the shutters. (9.20.1) 35mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and laying damp proof course 40mm thick with cement concrete 1:2:4 (1cement:2coarse sand (zone-III):4 graded stone aggregates 12.5mm nominal size

Making plinth protection 50mm thick of cement concrete 1:3:6 )over 75mm thick bed of dry brick ballast 40mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30cm measured to a height of 1m above ground level and removal of rubbish up to a distance of 50m outside the priphery of the area cleared

Sanitary Installations & Water Supply Works:Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device…......W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430X260X350mm and 340X410X265mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass…......One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern with fittings, standard size G.I./ PVC flush pipe…........Single squatting plate with 5 litre P.V.C. automatic flushing cistern

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash Flash back wash basin size 450X300 mm with single 15mm C.P. brass pillar taps

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing Rectangular shape 453X357mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stability for hot and cold water supply, including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling and testing of joints complete as per direction of Engineer in Charge. External work (18.9.1) 15mm nominal outer dia pipes

25mm nominal outer dia pipes

50mm nominal outer dia pipes

100mm nominal outer dia pipes

Making soak pit 2.5m diameter 3.0 metre deep with 45X45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100mm diameter, 1.8m long complete as per standard design. (19.32.1)With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms (i)15mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and approved make conforming to IS:8931 (i)15mm nominal bore

Electrical Works :Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group A

Group B

Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 2 Nos 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

2 X 10 sq. mm + 1 X 6 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch

2 way 5/6 amps switch

15/16 amp switch

3 pin 5/6 amp socket outlet

6 pin 15/16 amp socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 1 or 2 Module (75mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

8 Module (125mmX125mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Single pole and neutral

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 amps

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Supplying of following sizes XLPE insulated and PVC sheathed aluminium conductor armoured power cable of 1.1 KV grade conforming to IS 7098 (Part - I) / 1988 with amendment up to date etc as required. 3&1/2 core 185 sq. mm

1200 mm sweep ceiling fan (Make- USHA : Model Name :Energia 32 5 star…..

LED Bulb: KOLORS brand 9watt model no: 2204BU09 (CW)

LED batten: KOLORS brand 20 watt model no: 2402BA20 (WW) KARIS LED BATTEN LIGHT

12 watt KARIS SURFACE LED PANEL LIGHT ROUND, Model no: 2403PL12R (WW)

Supply, Installing, Testing and Commissioning of Inverter type split AC having full rated cololing capacity not lerss than 5100 BTU / hour with ISEER value not lesds than 4.3 ( or amended value upto date for 5 Star Rating value suitable for 230 V 40 Hz single phase AC supply i/c earthing connection etc complete as required.