138WE/L-78/2021-22

Amount

Demolation of cement concrete unreinforced in ground floor and pavings n.exc 15cm thick below or above ground level complete all as specified and as directed.

Demolation of cement concrete unreinforced in any description and any position not otherwise specifically provided for.

Dismantling floor, hearth or wall tiling including wall cement mortar, bedding (but not backing) and rubbish of premises complete all as directed.

Demolation of precast concrete block walling built in cement mortar, including all quoins, arches, pillars etc all as specified and as directed.

Taking down cement plaster on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc, complete all as specified and as directed.

Taking down chowkats / frames with shutters (without taking off shutters from the frames) area n.exc 1.5 Sqm each complete all as directed by Engr-in-charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as directed by Engr-in-charge.

Taking down shutters of any description area exceeding 1 Sqm and not exceeding 2 Sqm each complete all as directed by Engr-in-charge.

Ditto as item No 8 above but n.exc 1.0 Sqm complete all as directed by Engr-in-charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden panes or stone, concrete or brick surrounds, glazed with oil putty or fixed with beads complete all as specified and as directed.

Demolition of reinforced cement concrete in any position not otherwise specifically provided for all as directed.

M&L reinforced cement concrete 1:2:4 type B1 (20mm graded aggregate) for slab supported on wall, beams and columns in floors, roofs, landings, shelves and the like.

M&L from work to soffits of suspended flat sabs such as roof slabs, floor slabs, landing and similar work (Rough finshed flat surface of concrete) not exceeding 200mm thick (Horrizontal or sloping).

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to.

M&L for 75 mm PCC 1:3:6 type C1 using 20mm graded aggregate as plinth protection finished even and smooth with out using extra cement.

M&L forming contraction (dummy) joints 50mm deep x 10mm wide, filled with sealing compound grade 'A' in plinth protection.

M&L for 75 mm PCC 1:4:8 type D-2 using 40mm graded aggregate as in sub base of floor all as specified.

M&L PCC 1:2:4, 40 mm thick type B-1 using 20mm graded stone aggregate as in floor finished even and fair with out using extra cement complete all as directed by Engr-in-charge.

M&L for non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.11 but n.exc 18 Sqm in floor etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match, including screed bed with CM (1:4) 15mm thick laying floor tiles complete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.06 and nexc 0.11 Sqm in floor etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match, including screed bed with CM (1:4) 15mm thick laying floor tiles complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25 mm thick over cement screed bed 20mm thick in CM 1:6, set and jointed in neat cement slurry laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete.

M&L for glazed ceramic coloured tiles in vertical surfaces 350 x 250/450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match over 10mm thick CM (1:4) in dedo/skirting tiles complete all as specified and directed.

S&F rotational mouled polyethylene water storage tanks (cylindrical vertical with closed top) of 500 ltrs hoisted and fixed in position all as specified in SSR incl taking down existing water tank all as directed.

S&F in repairs bib tap cast copper alloy chromium plated butterfly handle screwed down screwed for iron pipe completed (15mm dia tap).

S&F in repairs 15mm bore pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe.

S&F in repairs angle stop valves, cast copper alloy, screwed down high pressure with cruth or butter fly handle, fancy type, chromium plated with long shank and cup (concealed type), 15mm bore dia of pipe fixed in repairs, complete all as directed by Engr-in-charge.

S&F in repairs swivel shower with arm of PTMT any colour for fixing with 15mm pipe (Min wt 40 gms) with shower arm 15mm size, 195 mm long with band of 45 degree with flang of PTMT any clour of (40gms).

S&F in repair PVC connection pipe suitable for connecting flushing cistern and WHB etc 450mm long complete all as specified and directed.

S&F Grating round 140mm size PTMT (Min weight 50 grms).

S&F in repairs soap dish chromium plated.

S&F in repairs towel rail 600 mm long chromium plated (Min weight 190 grms).

Taking down steel tubing 20mm bore of pipe and connections in any position including cleaning for refixing or removal to store complete all as directed by Engr-in-charge.

S&F of 3 layer PP-R polypropylene random copolymer pipes 20mm dia SDR 7.4 & (NP 16) 11 UV stablised and antimicrobial fasion welded having thermal stability for hot and cold water supply including all PP-R plain & brass threaded polyproplene random fittings fixed complete to wall, ceiling or in floors etc.

S&F in repairs PP-R gate valves 20mm dia (brass inset) as per requirement of the site.

S&F in repairs vitreous china squatting pan 'Orissa' pattern, size 580 x 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) and all as directed by Engineer-in-charge.

S&F in repairs 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with linlet, ball valve, float and handle including brackets.

S&F in repairs for wash basin, vitreous china, white, flat back, size 630x450mm excluding taps waste, chain and plug and porcelain stopper but incl brackets as specified & directed.

S&F in repairs waste cupling for bore dia 32 MM discharge pipe of PTMT (half or full threaded) minimum weight 32-45 gms/40mm-60gms).

S&F in repairs vitreous china bowl urinal, flat back, size of 465x355x265mm white with grating and union for discharge pipe and PTMT waste coupling with waste pipe (excluding flushing cistern, flush pipe and waste pipe).

Dismantling CI/PVC pipes of up to 100mm bore with fittings.

S&F 110mm bore PVC (SWR) pipes single socked, in any length with rubber joints fixed to walls complete all as specified and directed by Engr-in-charge.

S&F PVC (SWR) 'S' trap of 110mm bore.

S&F 110mm dia (SWR) bend any redius complete all as specified.

M&L for PCC type C2 (1:3:6) using 40mm graded crushed aggregate as mass conc and filling of foundation.

M&L for PCC type D2 (1:4:8) using 40mm graded crushed aggregate as mass conc and filling of foundation.

M&L for precast solid block masonry set in CM 1:6 & casted in cement concrete type C-1 (1:3:6) using 20mm graded curshed stone aggregate complete all as specified and directed.

M&L for 10mm thick rendering on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified and as directed.

M&L for 15mm thick rendering on fair faces of brick works finished even and fair without using extra cement in cement mortar 1:4 complete all as specified and as directed.

M&L for 5mm thick rendering on ceiling finished even and smooth without using extra cement in cement mortar 1:3 complete all as specified and as directed.

M&L for anodised aluminium frame of standerd section for doors, windows, ventilators, partitions etc with double rebates including joining cleat for fixing etc, complete all as specified & directed.

M&L for anodised aluminium windows and ventilators shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing , anodised aluminium snap beading, screws, anodised aluminium fitings such as peg stays 150mm long (1 no) hinge type B-21 100mm long (2 no) suitable handle (1 no) complete all as specified.

M&L sheet glass 5.5 mm thick ordinary quality and glazing with aluminium beeds in square exc 0.50 Sqm in each pane complete all as specified & as directed.

S&F 2nd class soft wood plain, soild, straight chowkets and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as directed by Engr-in-charge.

S&F mild steel work as in hold fasts and similar work confirming to Fe-290 or Gd-E 165 complete all as specified and as directed by Engr-in-charge.

M&L PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) as in hold fasts, bed block and like complete all as specified and as directed by Engr-in-charge.

S&F for 35mm thick 2nd class hard wood plain framed factory made paneled shutters (any number of panels) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated

M&L sheet glass 3mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane complete all as specified and as directed.

M&L figured glass 3mm thick ordinary quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane complete all as specified and as directed.

S&F mild steel butt hinges, medium weight cold rolled 100mm size complete all as specified and as directed.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and as directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.

S&F for factory made, solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M S tubes for top & bottom rails, M S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Paneling of plain colour sheet to be fitted in the M S frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified and as directed by Engr-in-charge.

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed by Engr-in-charge.

S&F in mild steel butt hinges, medium weight cold rolled 75 mm size complete all as specified and as directed.

S&F 100 mm long aluminium anodized, barred tower bolt of extruded section complete all as specified and as directed.

S&F 100 mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.

S&F in repair 300 mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

S&F in repair 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extrubed section or cast alumimium alloy fixed complete all as specified and directed.

M&L for preperation of new plastered wall surface of any description and applying three coat of white wash complete all as specified and as directed.

M&L for preperation of old plastered wall surface of any description and applying two coat of white wash complete all as specified and as directed.

M&L for preperation of old plastered ceiling surface of any description and applying two coat of white wash complete all as specified and as directed.

M&L for preperation of new or previously untreated wooden surface any description of over 10 cm in width or girth and applying two coat of synthetic enamal paint over a coat of Pink primer complete all as specified and as directed.

M&L for preperation of old wooden surface any description over 10 cm in width or girth and applying one coat of synthetic enamal paint complete all as specified and as directed.

M&L for preperation of new concrete / plastered surface of any description and applying two coat of exterior emulsion paint over a coat of primer on wall complete all as specified and as directed.

M&L for preperation of new concrete / plastered surface of any description, applying two coat of destemper oil emulsion over a coat of primer with alkali resistance priming paint on wall complete all as specified and as directed.

Dismanting wall and ceiling boards (fibre, pulp, insulation etc) any thickness including cover filters as directed .

M&L 9mm prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work.

Detto - all as per item No 78 above but on ceiling.

M&L fixing only 9mm pre-laminated particle board.

Dismanting of unframed fillets, rails posts, rafters, purlins etc. Under 40 sq Cm in section.

M&L for plain fillets, square rectangular or triangular in section clean swan, secured with nails or brads of section area exc 13 & nexc 25 sq cm in 2nd class soft wood.

M&L for covered fillets of standard hard board 3mm thick and 40 mm wide and fixing with screws complete all as specified and as directed.

S&F in repairs 19 mm dia mild steel. Chromium plated curtain rods, with brackets, end bulbs all as directed by Engr-in-charge.

Dismantling roof tiles or roof treatment of any description including cement mortar, bedding (but not backing) and rubbish of premises complete all as directed.

M&L for cutting out cracks to V section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3.

M&L for brushing neat cement slurry with 3.0 kg of cement per sq meter.

M&L PCC 1:2:4, 25mm thick type B0 using 12.5 mm graded stone aggregate as in floor finished even and fair with out using extra cement complete all as directed by Engr-in-charge.

M&L for 20mm thick rendering on fair faces of brick works finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified and as directed.

M&L for priming surfaces and applying normal treatment (for severe conditions) using glass fibre base bitumen felt, grade 2 all as specified and directed.

M&L APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforment with polyster non woven fabric (wt not less than 150 gms/sqm) laid on primed surfaced application including removing old damaged existing roof treatment, complete all as specified.

Dismanting framed wooden fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc under 40 sq cm in section.

M&L for 2nd class soft wood plain filletes square, rectangular or triangular in section clean sawn as in beeding for edges of ceiling, lining or wooden flooring work fixed with nails exc 6 sqcm and n exc 13 sqcm in section, complete all as specified and as directed.

S&F in repairs PUF water storage tanks (cylindrical vergical with closed top) 1000 Ltr capacity hoisted and fixed in position all as specified in SSR Part I including dismantling existing water tanks.

Applying a thin film of cement slurry 2mm thick mixing with water proofing compound as per manufacturers instruction on floor surface.

M&L preparing old plasted surfaces of wall and applying two coats of distemper oil emulsion with complete removal of existing treatment.

S&F galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples.

M&L for preparing old plastered surfaces of walls and applying one coats of exterior emulsion paint.

Taking down carefully copper/aluminium point wiring (light, fan, socket and power point) complete fittings such as switches, ceiling rose, regulators, socket etc and removing material from site with and making good disturbed surfaces of walls, floors/ceiling to match the existing surface, complete all as specified and as directed by Engr-in-charge.

M&L for point wiring for one light point or fan point controlled by one switch with PVC insulated copper conductor stranded cable of size 1.5 sqmm and including PVC casing/caping terminated in existing sunk Cl/ pressed steel terminal boxes for fixing and 1.5 sqmm PVC insulated copper wire as earth wire connected to earth folly and 3.00 mm thick plastic lamiated sheet cover all as spfd and directed by Engr-in-charge.

All as per item No 100 here-in-before but 1.5 sqmm for 5 Amps Switch socket outlet including 1.5 sqmm insulated copper wire as earth wire to the same earth dolly on same board.

All as per item No 100 here-in-before but 1.5 sqmm for 5 Amps Switch socket outlet including 1.5 sqmm insulated copper wire as earth wire to the same earth dolly on Independent board.

M&L for point wiring for 3 pin 15 Amps socket outlet independent with copper conductor cable PVC insulated multistrand 2.5 sqmm with 1.5 sqmm PVC copper conductor as earth wire connected to earth dolly and including PVC casing / caping with sunk cast iron.

S&F Switch piano, flush type, single pole, one way, 5/6 Amp 240 Volts, complete all as specified and as directed.

S&F Switch Socket combination two -in -one, 3 pin 5 and 15 Amp flush type universal complete all as specified and as directed.

S&F Switch Socket combination 3 pin 5 Amps two-in-one flush type (multipurpose) suitable for 2/3 pin plug complete all as specified and as directed.

S&F Socket outlet two-in- one, 3 pin, 5 Amp complete all as specified and as directed.

S &F Decorative ultra slim liner LED Lightining , 230 volts, single phase, 18 Watt, 6000K fixture with co extruded poly carbonate body, Enviromental friendly, energy efficient ready to use pack 1X18 W tube rod all accessories internally pre wired and connecting up with twin core twisted flexible copper conductor of suitable size

S&F LED lamp 10 watt (warm white) 230V, complete all as specified and as directed.

Supply and replacement of ceiling rose, surface bakelite 65 X 50mm Two to three terminals complete all as specified and directed by Engr-in-charge.

M&L for lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed by Engr-in-charge.

S&F Energy saving new generation 10W LED bulkhead luminaire with opal diffuser including making electric connection with three core copper conductor of appropriate size to the ceiling rose or from the junction boxes complete all as specified and directed by Engr-in-charge.

Supply and fix in replacement of sheet metal enclosures TPN for DBs with 200 Amps double door 415 volts 4 ways with IP-43 complete all as specified and directed by Engr-in-charge.

Supply and fix in replacement of sheet metal enclosures for DBs with 200 Amps double door when MCB's to be used single pole & neutral 240 volts 8 ways complete all as specified and directed by Engr-in-charge.

Supply and fix in replacement of sheet metal enclosures for DBs with 200 Amps double door when MCB's to be used single pole & neutral 240 volts 12 ways complete all as specified and directed by Engr-in-charge.

Supply and fix in replacement of MCB SP 6-32 Amps 240 volts 50HZ complete all as specified and directed by Engr-in-charge.

Supply and fix in replacement of MCB SPN 63 Amp 240 volts ISI marked complete all as specified and directed by Engr-in-charge.

Supply and fix in replacement of MCB TPN 63 Amp 415 volts ISI marked complete all as specified and directed by Engr-in-charge.

M&L in replacement for sub main wiring 4 runs of FR PVC insulated multistrand, copper conductor cable of size 10 sqmm along with two run of 6.0 sqmm PVC insulated cable 1100 volts multi stranded copper conductor as earth wire in and including PVC casing & capping.

Supply and fixing , connecting and testing Bldg Security light LED type suitable for working on 230 Volts, 50Hz, Ac of 48 Watts complete all as specified and directed by engineer in charge

M&L GI Braclet made out of 50mm dia medium grade pipe 1.2m length to shape for fixing on wall and suitable for 48 Watts street light with 02 Nos clamps of flat iron (40X4mm) nuts, bolts and washers complete all as specified and directed by engineer in charge

M&L for XLPE insulated armoured, heavy duty electric cable with aluminium conductor cable 1100 Volts grade , 4 core , cross sectional area 25 Sqmm

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m depth and getting out for laying of cable / pole in hard / dense soil complete all as specified and directed by Engr-in-Charge.

Returning, filling in, including spreading, leveling watering, and well ramming in layers not exc 25 cm in hard / dense soil complete all as specified and directed by Engr-in-Charge.

Removing excavated material n.exc 50m and depositing where directed at a level exc 1.5 m above the starting point complete all as specified and directed by Engr-in-charge.

M&L for crushed stone sand cushioning to UG cable, provide with the layer 8 cm before and 15 cm after laying and stretching jointing and testing the cable complete all as specified and directed by Engr-in-Charge. Note : Punned thickness shall only be measured.

Supply and fix GI pipe light grade of sizes 50mm dia for electric cable protection complete all as specified and directed by Engr-in-Chrage.

M&L for earthing complete with galvanised steel earth plate 600x600x6mm buried directly in ground vertically to a depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below ground level connected to and including GI wire of size 4mm dia by means of nuts, bolts, washers etc made of and connected to test point and earth dolly as all shown in electrical plate No 3 of SSR Part-I 2009 and specified or indicated including excavation and earth work in any type of soil, PCC (1:3:6) type C1 in chamber, pre cast RCC slab 50mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric or XPM jali (weight not less than 4.0 kg/Sqm) with cast iron frame, funnel, with wire mesh, 20mm bore light grade GI watering pipe, lugs, 15mm bore light grade GI protecton pipe, test point etc complete all as specified and as directed. Note : (i) item includes the cost of 7.5m GI pipe for protection of earth lead. (ii) Item includes the cost of 7.5m GI earth lead.

Suppling and laying unreinforced precast concrete cable cover, class LV, type 1 flat of size 250mm x 150mm x 40mm complete all as specified and directed by Engr-in-Charge.

S&F LED bulk head light fitting 1x13.5 watt 230 volt attractive wall / ceiling mounted any type with white reflactor comlete with all accessories prewired and including connecting up with twin core twisted flaxible copper conductor cable complete all as directed.

S&F for LED light fitting incl LED tube light batten type 1x20 watt, mounted on integrated sleek extruded polycarbonate LED channel with white accrylic cover suitable for 230 volt 50 Hz cool white colour bipin holder connector block etc complete with all accessories internaly prewired and including connecting up with twin core twisted fiexible copper conductor cable of suitable size complete.

M&L for sub main wiring with two RUNS of single core 2x6 sqmm for main and neutral wire and one run of single core 6 sqmm as earth wire of multi standed copper conductor FRLS insutated unsheathed cables conforming to IS : 694 drawn through and including medium duty unplasticised PVC capping cassing conforming to IS : 9537 (Part-3) and ISI marked accessories all conforming to IS specification complete all as specified and directed. Make - Havells/Plaza/Finolex Note : Two run of 6 sqmm and one run of 6 sqmm wire / cable and PVC conduit pipe shall be measured and paid as one run unit.

Taking down existing unserviceable /old DBs from any height and make complete including disconnection from exesisting MCBs/isoletors etc. complete all as specified and directed.

S&F of LED light energy saving & environmental friendly long life versatile pressure dia cast aluminium, IP66 street light of 25 watt 5700K 240 Volts single phase LED light suitable for 40MM dia pipe for fixing on wall including connection with suitable size 3 core PVC cable complete all as specified and directed.

M&L for GI pipe (light grade) with all fitting laid in trenches/wall complete for protection UG cable when crossing the road of size 40 mm bore

Taking down old unservicable LT U/G cable of 2/4 core 10/16 sqmm to 25 sqmm

R B TRADERS

Mehar Enterprises

M/S BALI CONSTRUCTIONS

M/S SHAMSHER ALI SUFI

M/S MUNEER HASSAN AKHON

AMAAN ENGINEERS

M/s Siachen Construction Co.

S S BUILDERS

Rampal Singh Contractor