Civil maintenance works inside power house area of CTPS , DTPS and at ash dyke area of HTPS, Kasimpur, Aligarh, Uttar Pradesh for 06 months

Disposal of malwa surplus earth and waste of construction material collected from desired place and disposal the same outside the colony upto 2K.M.

Carriage of earth and rubbish and concrete waste by mechanical transport including loading, unloading and stacking upto lead 3 km

Carriage of earth from Power house area/ intake channel by Mechanical means Transport including loading ,unloading and stacking up to 7 Km. up to New ash pond. As and when required at any point of New Ash bundh.

Disposal of the silt/sludge up 7 km at new ash bundh and disposed earth to be leveled at the site

Carriage of material by mechanical transport including loading ,unloading stacking of soling stone up to 1km

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth,lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.All kinds of soil.

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m.All kinds of soil

Clearing jungle including uprooting of rank vegetation, grass brush wood, trees and sapling of girth up to 30cm measured at a height of 1 mtr. above ground level and removal of rubbish up to a distance of 50mtr outside the periphery of the area cleared.

Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.

Filling with available fly ash and earth (excluding rock) in trenches or embankment in layers (each layer should not exceed 15 cm), with intermediate layer of compacted earth (Soil density of 98%) after every four layers of compacted depth of fly ash, sides & top layer of filling shall be done with earth having total minimum compacted thickness 30 cm or as decided by Engineer -in-charge, including compacting each layer by rolling/ ramming and watering, all complete as per drawing and direction of Engineer -in - charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

P/L in position cement concrete 1:4:8 ( 1 cement : 4 coarse sand 8 graded stone aggregate 40mm nominal size) excluding the cost of centering and shuttering- all work up to plinth level.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers,abutments, pillars, posts, struts, buttresses, string or lacing courses,parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:1½:3 (1 cement : 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size). cum 8976.45

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification. per 50kg cement bag

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars

Smooth finishing of the exposed surface of R.C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand)

DESIGN MIX CONCRETE Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately).All works above plinth level upto floor V level

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/ cum.Excess/less cement used as per design mix is payable/ recoverable separately). All works upto plinth level

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/ cum.Excess/less cement used as per design mix is payable/ recoverable separately). All works above plinth level upto floor V level

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in: 6.2.1 Cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with clay flyash F.P.S. (non modular) brick of class designation 7.5 in superstructure above plinth level up to floor five level in : Cement mortar 1:4 (1 cement : 4 coarse sand)

Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete.

Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and the cost of bolt etc complete. Fastener with threaded dia 10 mm

Stone work (machine cut edges Veneer work) for wall lining upto 10 m height, backing filled with a grout of 12 mm thick cement mortar 1:3 (1 Cement : 3 coarse sand) and jointed with Cement mortar 1:2 (1 cement : 2 stone dust), including rubbing and polishing complete. (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately). Kota stone slabs exposed face dressed and rubbed. 25 mm thick

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).Sal wood

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).Kiln seasoned and chemically treated hollock wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) Second class teak wood 30 mm thick shutters

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) Second class teak wood 30 mm thick shutters

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Kiln seasoned and chemically treated hollock wood

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.Kiln seasoned and chemically treated hollock wood 35 mm thick

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Kiln seasoned and chemically treated hollock wood 30 mm thick

Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or graded wood particle board IS : 3087 marked,to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately): 12 mm thick

Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately).18 mm thick

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 plyveneering with vertical grains or cross bands and face veneers on both faces of shutters:30 mm thick including ISI marked Stainless Steel butt hingeswith necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction withframe of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on bothfaces of shutters:25 mm thick (for cupboard) including ISI marked nickel platedbright finished M.S. piano hinges with necessary screws

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :kiln seasoned and chemically treated hollock wood 50x12 mm

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets :20 mm dia (heavy type) metre

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete 200x10 mm

P/F hard drawn steel wire fabric 75x25mm mesh of weight not 7.75 Kg. per Sqm to window frames etc including 62x19 mm beading of IInd class Teak wood.

Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. With 12 mm mild steel U beading

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand:6 graded stone aggregate 20mm nominal size).

Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete.125x65x2.12 mm

Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete.100x58x1.90 mm

Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete.75x47x1.70 mm

Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete.50x37x1.50 mm

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :300x16 mm

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :250x16 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :250x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :200x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :150x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :100x10 mm

Providing and fixing ISI marked 85x42 mm oxidised M.S. pull bolt lock conforming to IS : 7534 with necessary screws bolts, nut and washers etc. complete

Providing and fixing ISI marked oxidised M.S. door latches confirming to IS: 7534 with necessary screw, bolts, nuts and washers etc. complete :300 x 20x 6 mm

Providing and fixing ISI marked oxidised M.S. door latches confirming to IS: 7534 with necessary screw, bolts, nuts and washers etc. complete :250 x 20 x 6 mm

Providing and fixing ISI marked oxidised M.S. door latches confirming to IS: 7534 with necessary screw, bolts, nuts and washers etc. complete :125 mm

Providing and fixing ISI marked oxidised M.S. door latches confirming to IS: 7534 with necessary screw, bolts, nuts and washers etc. complete : 100 mm

Providing and fixing ISI marked oxidised M.S. door latches confirming to IS: 7534 with necessary screw, bolts, nuts and washers etc. complete :75 mm

Providing and fixing oxidised M.S. Safety chain with necessary fixtures for doors, (weighting not less than 450 gms)

Providing and fixing bright finished brass door latch with necessary screws etc. complete 250x16x5 mm

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete

Providing and fixing aluminium tee channels (heavy duty) with rollers & stop end in pelmets as curtain rod

30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge.

Providing and fixing PVC rigid foam sheet 1 mm thick on existing door shutters (bathroom and W.C. doors) using synthetic rubber based adhesive.

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-incharge (Frame work shall be paid for separately). 12mm thick commercial ply conforming to IS : 1328 BWR type

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position, including transporting and applying a priming coat of approved steel primer all complete

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces.

Welding by gas or electric plant including transportation of plant at site etc. complete.

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete.

Providing and fixing glass strips in joints of terrazo/ cement concrete floors.40 mm wide and 4 mm thick

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey,Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc, complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete of size of tile 600X600 mm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 800x800 mm

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.63 mm thick with zinc coating not less than 275 gm/ m².

Providing high impact Polypropylene reinforced cement 6 mm thick corrugated sheets (as per IS: 14871) roofing up to any pitch and fixing with polymer coated J, or L hooks, bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete (excluding the cost of purlins, rafters and trusses), includingcutting sheets to size and shape wherever required.

Painting top of roofs with bitumen of approved quality @ 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete :With residual type petroleum bitumen of grade VG -10

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.75 mm diameter

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter

Providing & fixing on wall face 110 m.m. diameter unplasticised PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gape for thermal expansion.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 75 mm bend

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm bend

12 mm cement plaster of mix :1:4 (1 cement: 4 coarse sand)

12 mm cement plaster of mix :1:6 (1 cement: 6 coarse sand)

Neat cement punning.

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

White washing with lime to give an even shade: New work (three or more coats)

Colour washing such as green, blue or buff to give an even shade : New work (two or more coats) with a base coat of white washing with lime

Applying one coat of water thinnable cement primer of approved brand & manufacture on wall surface.

Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm of approved brand or manufacture

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture

Applying priming coat with ready mixed grey or pink primer of approved brand & manufacture on wood work(hard & soft wood)

Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces : Two coats

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.

Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution.

Lettering with black Japan or approved paint of approved band and manufacture.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

White washing on old work(one or more coat)with lime to give an even shade.

do but additional coat (If required and instruction given by Engineer-in-charge.

Colour washing on old work (one or more coat)with lime such as green,blue or buff to give an even shade.

do but additional coat (If required and instruction given by Engineer-in-charge.

Distempering with oil bound washable distemper of approved brand & manufacture to give an even shade on old work.(one or more coats)

do but one ad. Coat.(If required and instruction given by Engineer-in-charge.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :Old work (one or more coats) .

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : One or more coats on old work

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work.

Same as above but for one ad. Coat. (If required and instruction given by Engineer-in-charge.

Finishing walls with water proofing cement paint of required shade old work (one or more coats applied @2.20Kg/10Sqm.Complete

Same as above but for one ad. Coat.(If required and instruction given by Engineer-in-charge.

Finishing walls with acrylic smooth exterior paint of required shade of old work(one or more coats applied @ 0.90 ltr.per 10 Sq.Mtr)

Same as above but for one ad. Coat.(If required and instruction given by Engineer-in-charge.

Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground within 50 meters lead : Door chowkhats

Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground within 50 meters lead : windows chowkhats

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of thickness 4 mm

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty Float glass panes of thickness 5.5 mm

Renewal of old putty of glass panes (length)

Refixing old glass panes with putty and nails

Raking out joints in lime or cement mortar and preparing the surface for re-pointing or replastering, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.

Ptoviding and Fixing 20 mm dia curtain rods

Applying french sprit polishing (one or more coats) on old work.

Re-lettering with black japan paint of approved brand & manufacture.

Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-In- Charge.

Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within.50metres lead as per direction of Engineer - in- charge

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar

Taking out doors,windows and clerestory windows shutters(steel or wood) including stacking within 50 meters lead of area 3 sq meters and below

Dismantling steel work in built up sections in angles ,tees,flats and channels including all gusset plates,bolts,nuts,cutting rivets,welding etc. including dismembering and stacking within 50 meters lead

Demolishing dry brick pitching in floors, drains etc. including stacking of serviceable material and disposal of unserviceable material within 50 metres lead :

Dismantling GI Pipe including excavation and reffering trenches after taking out the pipe manually by mechanical means including stacking of pipe with in 50 mtr lead as per direction of E/in charge 15 mm to 40 mm dia

Dismantling GI Pipe including excavation and reffering trenches after taking out the pipe manually by mechanical means including stacking of pipe with in 50 mtr lead as per direction of E/in charge 1Above 40 mm dia

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50metres lead.

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceablen material with in 50 meters lead as directed by Engineer-in-charge.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Supplying at site :R.C.C. Standards post/ struts/rails/ pales of mix 1:1.5:3 (1 cement : 1.5 coarsesand : 3 graded stone aggregate 12.5 mm nominal size) with wooden plugs or 6mm bar nibs wherever required as per direction of Engineer-incharge (cost of earth works in excavation, concrete works in foundation to be paid separately).

Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per mtr cost of total length of barbed wire used. With G.I. barbed wire metre

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade

Providing and laying four courses water proofing treatment with bitumen felt over roofs consisting of first and third courses of blown bitumen 85/25 or 90/15 conforming to IS : 702 applied hot @ 1.45 Kg per square metre of area for each course, second course of roofing felt type 3 grade-I (hessian based self finished bitumen felt) and fourth and final course of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic decimeter per square metre, including preparation of surface but excluding grading complete with : 22.8.1 Bitumen felt (hessian base) type 3 grade I conforming to IS : 1322

Dry brick (new) on flat flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.

Dry brick (old) on flat flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

OM NO. 1123/FM/MINIMUM WEDGE DATE-05/07/2019 Unskilled labour for misc. work at residential & non residential building in nw colony HTPS

providing and laying at site wire mesh (rabbit).

Painting top of roofs with bitumen of approved uality @ 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete : With residual type petroleum bitumen of grade VG -10

Fixing of deparmental flush door shutter including ISI MS accessaries.(Screw & Hinges etc,)

Job attending by one carpenter with one helper per hour or part of an hour

Providing & fixing water closet white vitreous china Orissa pattearn w.c pan of size 580x440 m.m. with integrial type foot restswith 100 m.m. dia sand cast iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe with manualy controlled device with all fitting & fixtures complete, including cutting and making good the walls and floors.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing kitchen sink including making all connections excluding cost of fittings.White glazed fire clay sink of size 600x450x250 mm

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern, with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required : 17.6.1 Single squatting plate with 5 litre P.V.C. automatic flushing cistern

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 450x 300 mm with single 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

p/f stainless steel A ISI 304(18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40mm, including painting of fittings and brackets, cutting and making good the walls where ever required kitchen sink with drain board510x1040mm bowl depth 250mm

Providing and fixing white vitreous china water closet squatting pan (Indian type) :Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan.

Providing and fixing a pair of white vitreous china foot rests of standard pattern for squatting pan water closet : 250x130x30 mm

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan Complete White solid plastic seat with lid

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of430x260x350 mm or 340x410x265 mm sizes respectively.

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : Flat back wash basin of size 550x400 mm

Providing and fixing white vitreous china laboratory sink including making all connections excluding cost of fittings: 17.27.1 Size 450x300x150 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.32mm dia Semi rigid pipe

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.32mm dia Flexible pipe

Providing and fixing 100 mm sand cast Iron grating for gully trap.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approve with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 453x357 mm

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete

Providing and fixing toilet paper holder C.P. brass

Providing and fixing soil, waste and vent pipes (Sand cast iron S&S pipe) 100 mm dia as per IS: 1729

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : For 100 mm dia pipe

Providing and fixing plain bend of required degree. 17.39.1 100 mm dia 17.39.1.1 Sand cast iron S&S as per IS - 1729

Providing and fixing door piece, insertion rubber washer 3 mm thick, bolts & nuts complete: 100 mm Sand cast iron S&S as per IS - 3989

Providing and fixing collar 100 mm Sand cast iron S&S as per IS – 1729

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: 100 mm inlet and 75 mm outlet Sand Cast Iron S&S as per IS- 1729

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. 17.69.1 Waste coupling 31 mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms

Waste coupling 38 mm dia of 83 mm length and 77 mm breadth, weighing not less than 60 gms

Providing and fixing PTMT urinal cock of approved quality and colour.15 mm nominal bore, 80 mm long, 42 mm high and 30mm wide with BSP female threads weighing not less than 48 gms

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 15 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 20 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings & clamps, i/c cutting and making good the walls etc. internal work. 25 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 15 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 20 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 25 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 32 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 40 mm dia nominal bore

Providing and laying of GI pipe B class complete with GI fitting including transcending and refilling etc 50 mm dia

Providing and laying of GI pipe B class complete with GI fitting including transcending and refilling etc 65 mm dia

Providing and laying of GI pipe B class complete with GI fitting including transcending and refilling etc 80 mm dia

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore

Making connection of GI distribution branch with GI main 50 to 80 mm nominal bore

Providing and fixing brass bib cock of approved quality : 15 mm nominal bore

Providing and fixing brass stop cock of approved quality : 15 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore

P/F gun metal gate valve with C.I. wheel of approved quality (screwed end) 40 mm dia nominal bore

P/F gun metal gate valve with C.I. wheel of approved quality (screwed end) 50 mm dia nominal bore

P/F gun metal gate valve with C.I. wheel of approved quality (screwed end) 65 mm dia nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 20 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) :25 mm nominal bore (Horizontal)

Providing and fixing gun metal non- return valve of approved quality (screwed end) :25 mm nominal bore (Vertical)

Providing and fixing brass ferrule C.I. Mouth cover including boring and taping the mains. 15 mm dia

Providing and fixing brass ferrule C.I. Mouth cover including boring and taping the mains. 20 mm dia

Providing and fixing brass ferrule C.I. Mouth cover including boring and taping the mains. 25 mm dia

Providing and fixing uplasticised PVC connection pipe with brass unions :30 cm length 15 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm length 15 mm nominal bore

Providing and laying certrifugally cast (spun) iron pipe (class LA) conforming to 1S.1536 100 mm dia pipe

Providing and laying certrifugally cast (spun) iron pipe (class LA) conforming to 15.1536 125 mm dia pipe

Providing and laying certrifugally cast (spun) iron pipe (class LA) conforming to 15.1536 150 mm dia pipe

Providing flanged joints to double flanged CI pipe and special including testing of joint 80 mm dia

Providing flanged joints to double flanged CI pipe and special including testing of joint 100 mm dia

Providing flanged joints to double flanged CI pipe and special including testing of joint 150 mm dia

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :15 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :20 mm nominal bore

Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required :15 mm nominal bore

Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required :20 mm nominal bore

Providing and fixing GI union in existing GI pipe line cutting and threading the pipe and making long secrew, including excavation refilling the earth or cutting of wall and good the same complete wherever requied 25 mm dia

Providing and fixing GI union in existing GI pipe line cutting and threading the pipe and making long secrew, including excavation refilling the earth or cutting of wall and good the same complete wherever requied 32 mm dia

Providing and fixing GI union in existing GI pipe line cutting and threading the pipe and making long secrew, including excavation refilling the earth or cutting of wall and good the same complete wherever requied 40 mm dia

Providing and fixing GI union in existing GI pipe line cutting and threading the pipe and making long secrew, including excavation refilling the earth or cutting of wall and good the same complete wherever requied 50 mm dia

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms 14mm nominal bore.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore

P/F PTMT stop cock of approved quality & colour 15mm nominal bore, 86mm long weighing not less than 88gms.

P/F PTMT pillar cock of approved quality & colour.15mm nominal bore, 107mm long, weighing not less than 110gms.

15 mm nominal bore, 80 mm long, weighing not less than 46 gms

Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS: 8329 : 150 mm dia Ductile Iron Class K-7 pipes

Dismantling old CI pipe including excavation and refilling trenches after taking out the pipes, breaking lead caulked joints, melting of lead and making into blocks, including stacking of pipes at site lead up to 50 mtr. 80 mm dia

Dismantling old CI pipe including excavation and refilling trenches after taking out the pipes, breaking lead caulked joints, melting of lead and making into blocks, including stacking of pipes at site lead up to 50 mtr. 100 mm dia

Dismantling old CI pipe including excavation and refilling trenches after taking out the pipes, breaking lead caulked joints, melting of lead and making into blocks, including stacking of pipes at site lead up to 50 mtr. 125 mm dia

Dismantling old CI pipe including excavation and refilling trenches after taking out the pipes, breaking lead caulked joints, melting of lead and making into blocks, including stacking of pipes at site lead up to 50 mtr. 150 mm dia

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 100 mm diameter

Dismantling of 100mm dia old SW Pipe line including braking of joint & bed concrete, stacking of useful material near the site within 50Mtr. lead & disposal of unserviceable material in nearest dumping place.

Providing and laying non-pressure NP3 class (Medium duty) R.C.C. pipes including collars/spigot joint with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete 450 mm dia. R.C.C. pipe

Providing and laying non-pressure NP3 class (Medium duty) R.C.C. pipes including collars/spigot joint with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete 600 mm dia. R.C.C. pipe

Providing and laying non-pressure NP3 class (Medium duty) R.C.C. pipes including collars/spigot joint with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete 900 mm dia. R.C.C. pipe

Providing and laying non-pressure NP3 class (Medium duty) R.C.C. pipes including collars/spigot joint with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete 1200 mm dia. R.C.C. pipe (Laying by mannual./mechanical means)

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately) : For fixed portion Anodized aluminium (anodized transparent or dyed to required shade according to IS:1868, Minimum anodic coating of grade AC 15)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12mm thick pre-laminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in paneling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

P/F double action hydraulic floor spring of approved brand and manufacture conforming to IS: 6315 having brand logo embossed on the body/plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors , embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece MS sheet outer box with slide plate etc. complete as per direction of E/I With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

P/F glazing in aluminum door , window, ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the direction of E/I. (cost of aluminum snap beading shall be paid in basic item)With float glass panes of 5.5 mm thickness

Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately).

Filling the gap in between aluminium frame and adjacent RCC/Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of E/I complete upto 5 mm depth and 5 mm width

Providing & laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of :(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. Per sqm of area. (iv) Ivth course of 400 micron thick PVC sheet.(Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

P/L four course water proofing treatment with bitumen felt (hessian base)over roofs consisting of 1’and 3’ courses of blown bitumen 85/25 or 90/15 applied hot @ 1.45 kg per M2 of area for each course, second course of roof felt type 3 grade-I and fourth and final course of stone grit 6 mm and down size gravel spread at 6 m3 dia. Per m2 incl. Preparation of surface.

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991,in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main- T runners of size 24x38 mm of length 3000 mm, cross - T of size 24x32 mm of length 1200 mm and secondary intermediate cross-T of size 24x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. With 15 mm thick tegular edged light weight calcium silicate false ceiling tiles.

Tractor with trolley with two labour for carriage work

Scaffolding net made of high density polyethylene UV stabilized having density 100gm/ sqm.

Providing and fixing gun metal non-return valve of approved quality (screwed end) 15mm nominal bore horizontal

Providing and fixing gun metal non-return valve of approved quality (screwed end) 15mm nominal bore Vertical

Attending leakages in pipelines or any fault including its fitting such tee elbow , socket including all labour and T & P required at site for the proper completion of work.

taking out W.C. pan replacement P or S trap refixing of W.C. pan making good.

Providing and fixing W.C. pan size 450mm Indian type pattern white viterous china squatting pan including dismantling of old existing W.C. pan including replacement china clay P-trap/S-trap including all labour T&P required for proper completion of the work

Cleaning of pipe line of all type of upto dia 50mm & fixing the same including all fittings if required for proper completion of work

Cleaning of chocked SCI/AC pipes & fixing the same against wall including all labour T&P omplete.(bathroom/toilet/rain water pipe)

Supply & fixing C.P. piller cock 15mm dia of approved quality.

M.S. angle 32x32x3mm brackets for washbasin & cistern of required length.

P/F cast iron push cock of approved quality of approx 400mm weight

Cleaning of RCC/PVC water tank constructed/mounted on roof of residential/non residential buildings with wire brush & waste mudy water may not get in any pipe line including cost of all labour T&P etc

Cleaning of all S.W. pipe after tanking out from the adjusting position and relaying the same after proper cleaning & jointing with 1:1C.M. after excavation & refilling for proper completion of the work

Providing and fixing CI bib cock of approved quality and minimum weight 300 gm with brass spindle.

Providing and fixing of zet of approved quality.

Providing and fixing of European type w.c. pan seat cover.

Providing and fixing of brass spindle for pillar cock

Providing and fixing of bib cock washer.

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with vibro tamper or vibrating plate compactor or tamper rammer of 0.5 to 1 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density.

Cleaning of old bricks recovered from demolition of old brickwork by removing mortar, lumps and any other loose material from bricks and making good for use in masonry.

Dismantling of RCC by using jack hammer along with operator complete and disposal of dismantled material .

Providing and laying GP 2 grouting

Epoxy Resin –C/257

Hardner-xy54

Sand Dust

Making 25 mm. dia bore of 200 mm depth with hydraulic hammer and grouting 20 mm bolt with chemical HIT RE500 of hilti brand (bolts shall be provided by UPRVUNL)

Making 30 mm. dia bore of 200 mm depth with hydraulic hammer and grouting 24 mm bolt with chemical HIT RE500 of hilti brand (bolts shall be provided by UPRVUNL)

Searching, sorting out and attending leakage and choking faults in external or internal running water mains, sever lines of different diameters at all elevations from 0 to 18 mm level including all materials as G.I bend , elbow, tee, socket, nipple etc. and supply of all labour, T&P such as thread cutting, dye, bunch voce, hacksaws pipe wrench etc.

Rewinding of 5.00 to 7.5 H.P capacity three phase vertical or horizontal motor for pump of tubewell with class B insulated copper wire of I.S.I approved quality including painting varnishing etc. complete as per direction of E/I

Repairing servicing of fully automatic three phase starter by replacing thermal relay including testing of load replacement of connecting wire required etc.

Cleaning of C.I down pipe from roof to bottom including all labour T&P complete dismantling and refixing complete

Supply and filling clinker/cinder in depressed portion of w/c including all labour material, T&P

Fixing Pre-Painted Coil coated steel false ceiling system, tile type square pattern panels 600x600 m.m. size at all level, for all kind of work, consisting of 0.5 mm tick galvanized to grade 180 as per IS:277, along with galvanized. Supporting Steel member exposed faces of galvanized Member to be Supporting with regular modified polyester coating/super polyester coating minimum 20 DFT to form panels of specified size for tile type panels and toll formed stove enameled 0.6 mm thick steel carrier, for Fixing of lineal type panels by clip on arrangement, suspended form RCC slab/structural steel or catwalk way steel channel grid above with 4 mm (minimum) galvanized wires (rods), with special height adjustment clips, providing angle section of minimum 25 mm leg with along the perimeter of ceiling, including all labor, material, supporting grid system (members minimum 0.8mm thick and galvanized @ 150g/sq.M.as per IS:277) equipment, handling, transportation, workmanship, anchor fasteners for making suspension arrangement from RCC. Including all labour, material T&P etc. Complete but excluding cost of false ceiling.

Attending complaints such as replacement of taps, washers, spindle for pillar cocks etc. by providing plumper at the complaints office including all labour T&P threads, safeda etc. required for proper completion of the work.

Cleaning of Septic Tank chambers & disposal of malwa outside the boundary wall of colony/ power house.

Cleaning of Inspection Chamber & disposal of malwa outside the boundary wall of colony/ power house.

Uprooting of pipal/ bargad trees from the walls or near the soil waste pipe of Ist/ IInd floor or on the roof of residential pipe including dismantling of brick work approx 1X23X65 Mtr. of taking out the roots of trees & repairing the wall in 1:6 cement mortar compete.

Fixing of old GI pipes including of old chocked GI fitting including S/F or required fitting (External work) 15 mm dia

Fixing of old GI pipes including of old chocked GI fitting including S/F or required fitting (External work) 20 mm dia

Fixing of old GI pipes including of old chocked GI fitting including S/F or required fitting (External work) 25 mm dia

Fixing of old GI pipes including of old chocked GI fitting including S/F or required fitting (External work) 32 mm dia

Fixing of old GI pipes including of old chocked GI fitting including S/F or required fitting (External work) 40 mm dia

Fixing of old GI pipes including of old chocked GI fitting including S/F or required fitting (External work) 50 mm dia

Laying of CI pipe excavated trenches in proper, alignment position including all labour T & P etc required for proper completion of work (excluding cost of pipe) 80 mm dia

Laying of CI pipe excavated trenches in proper, alignment position including all labour T & P etc required for proper completion of work (excluding cost of pipe) 100 mm dia

Laying of CI pipe excavated trenches in proper, alignment position including all labour T & P etc required for proper completion of work (excluding cost of pipe) 150 mm dia

Providing the bleaching powder

Supply and engage fitter/operator/carpenter / meson for emergency work as per direction Engineer incharge for proper completion work .

Carriage charge by Buggi with driver

Watch & ward of main pipeline and checking against any type of leakage and inform to the E/I.

P/F G.I. Pipe B class 150 mm

P/L four course water proofing treatment with bitumen felt (hessian base)over roofs consisting of 1’and 3’ courses of blown bitumen 85/25 or 90/15 applied hot @ 1.45 kg per M2 of area for each course, second course of roof felt type 3 grade-I and fourth and final course of stone grit 6 mm and down size gravel spread at 6 m3 dia. Per m2 incl. Preparation of surface. Bitumen provideed by department to IS: 1322

P/F 15 mm thick tegular edged light weight calcium silicate false ceiling tiles. false ceiling tiles of Size 595x595mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991

Attending complaint regarding aluminium work of door/window/partition including all labour, material T&P, Fitter and helper

Repairing & Fixing Pre-Painted Coil coated steel false ceiling system, tile type square pattern panels 600x600 m.m. size at all level, for all kind of work, consisting of 0.5 mm tick galvanized to grade 180 as per IS:277, along with galvanized. Supporting Steel member exposed faces of galvanized Member to be Supporting with regular modified polyester coating/super polyester coating minimum 20 DFT to form panels of specified size for tile type panels and toll formed stove enameled 0.6 mm thick steel carrier, for Fixing of lineal type panels by clip on arrangement, suspended form RCC slab/structural steel or catwalk way steel channel grid above with 4 mm (minimum) galvanized wires (rods), with special height adjustment clips, providing angle section of minimum 25 mm leg with along the perimeter of ceiling, including all labor, material, supporting grid system (members minimum 0.8mm thick and galvanized @ 150g/sq.M.as per IS:277) equipment, handling, transportation, workmanship, anchor fasteners for making suspension arrangement from RCC. Including all labour, material T&P etc. Complete but excluding cost of false ceiling.

Cutting & making opening of 0.6 M x 0.6 M of false ceiling

Job work of making hole for providing damper & finshing (600x600 mm)

cleaning of intake gate with 02 nos man power in timing(three shift) given below of C & D power house (U#7,8 & 9) including removing grass,bushes,wood ,trees and material . Placing and removing planks for mentaining required level of water at canal regulator including disposal of removed material from platform of intake gate ,clearing of jungle from he both side of platform and disposal of the same including all labour , T&P etc .required for proper completion of work . (a) 6:00 Hrs to 14:00 Hrs. (b)14:00Hrs to 22:00 hrs (c) 22:00 Hrs to 06:00 Hrs.

Removal of dead bodies of animals etc. from running water condition including all labour T&P required for proper completion of work

Sealing of gate of canalof canal regulatorsby pouring/ filling of cow dung mixed with doob grass during the period of canal closure or lack of water , including supply ,stacking and mixed with grass and then filing behind planks fixed in up stream side of canal .

providing addditional one man power with unji, phawara, Aari, Tasla, Bucket rope/ladder etc.required for emergency work like cleaning of return water channel, lifting and lowering planks at canal regulator or to assist the related work as when required incliuding cost of all T&P etc complete for 8 Hrs.

Hiring of J.C.B. Machine with operator, helper, fuel, lubricant etc. complete. As and when required within 2 hrs. of intimation given by A.E./J.E for different type of job like cleaning of Kachcha Nala along New /Old Ash bundh, Cleaning of return water channel, making drains/ channel in ash pond for diverting flow of ash slurry, for closing/ back filling of cuts in ash bundh etc. work carried out as per direction of J.E./A.E./ E.E.

providing 01nos Tractor diesel trolley 7.5 HP on hire basis with pump ,float valve ,hose pipe etc. complete with one operator & one helper along with cost of diesel ,mobile oil T&P etc.required for proper completion of work

Providing wooden planks including insert (nailing steel patti,M.S Rod etc)fixing in the wooden planks (second class devdar /jamun wood)size of planks 1660x250x63 mm for canal regulation site .

Providing hydraulic excavator (pocklane) of 01 cumec bucket including cost of operating staff.supply of lub oil & diesel also

Providing a gang of 03 nos. labours along with Phawara, Punji, Tasla, Aari/Darati etc. for cleaning of return water channel from New Ash pond to Canal. labour must wear gum boots, for safety etc. complete. As and when required. N.S.R. if more/less than prescribed no. of labour required than payment will be done as per requirement and availability of labour.

Providing and placing of plastic empty bags filled up with good quality of earth including properly sewing with jute plastic thread including placing earth filled up bags properly along with inside the ash bundh spur near filters and other places to protect toes from sories breach etc. including cost of empty plastic bags, labour T&P and good quality of earth etc. for completion of work as per direction of E/I.placing of earth fill plastic bags for making embankment at down stream of canal to ponding the wate

Providing a Gang of 05 persons alongwith Phawara, Punji, Tasla, etc. for making drain in ash pond for diverting flow of ash slurry, for protection of ash bundh and cleaning of Top of Ash bundh, Cleaning of chocked R.C.C. pipes of filters as and when required for smooth running of Ash bundh.

Providing and laying, commissioning of siphon for dewatering from Ash pond to near by Nala by using 100 mm dia high quality PVC suction/ delivery pipe length 15 M. and Mojama pipe of length 50 M (Plastic Pipe of dia 150 mm) complete. Rate included cost of all labours, Materials & T&P complete.

P/F 3HP ISI marka submercible 3 phase pump with control panel and cable etc all in complete

servicing and fixing of water cooler(water cooler will be perovided by nigam)

Suitable boring for casing pipe in rocky strata and developing bores by compressed air at different level tgill crystal clear water comes out and providing field test and strata as per direction of Engineer-in charge 150mm dia bire

Providing and fixing of casing pipe including its lowering in bore hole in collapsible strata and proper sealing as per direction of Engineer-in charge including cost of all meterial,labour ,and T&Petc . Required for proper completion of work 150mm dia bore PVC pipe

Hiring of pump set of 4000 Lt/hr Capacity with one man for operation and dewatring