SPL REPAIRS TO BLDG NO P 53 AT MIL STN ABOHAR

Amount

Demolition of cement concrete (un-reinforced) in floors / pavings, (below or above ground level) and of any description and in any position not otherwise complete all as specified and directed.

Demolition of cement concrete (reinforced) in roof, floors (other than ground floor), beams, staircase, landing, chajjas and similar suspended work complete all as specified and directed.

Demolition of mud in roofs of any thickness incl plastering and leeping complete all as specified and directed.

Dismantling of brick tiles or terracing tiles in roofs single layer complete all as specified and directed.

M & L for 75 mm thick cement concrete type C2, 1:3:6, (40mm graded stone aggregate) as in plinth protection/ path etc laid in suitable panels not exceeding 3.00 m length finished even and smooth without using extra cement with 10mm joints filled with bituminous sealing compound of grade 'A' / bitumen mastic filler /sealant, surface finished even and smooth without using extra cement complete all as specified and directed.

Cutting out concrete blocks, slabs, brickwork or stone masonry (in alternate course), forming toothings for and bonding new work in mortar into old work, including new materials entering old brick walls built in cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4, type B-0, as required (superficial area n. exc 150 sq cm) all as specified and directed.

M & L mild steel TMT bars 10mm dia or over cut to length bent to shape required including cranking, hooking ends and binding with MS wire (annealed) not less than 0.90mm dia all as in column, beam etc complete all as specified and directed.

All as per Ser item No 7.00 above but 5 mm dia and over up to and including 8 mm dia as in stirrups.

M&L for reinforced cement concrete M-25 (Design mix), using 20mm graded stone aggregate as in as in foundations, footings, foundation beams, plinth beams; bases for columns, etc. and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete M-25 (Design mix), using 20mm graded stone aggregate as in Columns, pillars, piers, posts & struts etc. all as specified and directed. Note : Form work & reinforcement measured separately.

M&L for reinforced cement concrete M-25 (Design mix), using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5 metre span all as specified and directed. Note : Form work & reinforcement measured separately.

M&L for reinforced cement concrete M-25 (Design mix), using 20mm graded stone aggregate in slab supported on walls,beams and columns in floors, roofs, landings, balconiies,deck slabs and in shelves and the like all as specified and directed. Note : Form work & reinforcement measured separately.

M&L for Form work to sides of concrete foundation, footings bases of columns and plinth beams and similar works rough finished surfaces of concrete complete all as specified and directed.

M&L for Formwork to soffits of suspended slabs, such as roof slabs, floor slabs landing and similar work not exceeding 200mm thick (Horizontal & sloping) fair finished surfaces. Note : Steel props shall be used.

M&L for From work to edges of concrete flates treads breaks in floors, window cill concrete railing, opening in convert valley floor and roof exc 5cm and n.exc 10 cm wide and sides RCC/PCC band in walls complete all as specified and directed.

M&L for Formwork to sides of pillars, posts, struts, piers columns & stanchions : rough finished surface of concrete flat complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

Dismantling of brick work built in any cement mortar complete all as specified.

M&L for Brick work using fly ash bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

All as per Ser item No 19.00 above but except bricks all as specified.

M & L for brick work in half brick thick wall using fly ash bricks straight or curved on plan to any radius built in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

Dismantling of floor hearth or wall tiling including cement mortar bedding ( but not backing) and rubbish off the permices complete all as specified and directed.

Roughening surface of old concrete floor by picking sweeping clean and washing down with water to remove dust etc.

M & L for Glazed ceramic light shade tiles in vertical surface 350x 250x 7 mm/ 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match in vertical surface in neat cement slurry and pointed in white cement paste pigmented to the shade over and including 10mm thick screed bed in CM (1:4) complete all as specified and directed by Engineer - in - Charge.

M & L for non skid ceramic colour (light shade) joint free tiles with matt finish, 7 to 8 mm thick ( square/ rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in paste pigmented to tile shade over and including 15mm thick screed bed in CM (1:6) complete all as specified and directed by Engineer - in - Charge.

All as per Ser item No 25.00 above but as in skirting over and including 10 mm backing in CM ( 1:3) complete all as specified and directed by Engineer - in - Charge.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid bedded and pointed in any mortar complete all as specified and directed.

M & L Machine cut kota stone slab flooring 20 - 25 mm thick of size 550mm X450mm and in single piece over cement screed base laid over and including 15mm thick screed bed in cement mortar 1:6 set and jointed with grey cement slurry mixed with pigment to match of the slab including rubbing and polishing complete all as specified and directed by Engineer - in - Charge.

M & L Machine cut kota stone slab 20 - 25 mm thick in riser of steps,in single piece skirting, dado and pillar over cement screed base laid over and including 10mm thick backing in cement mortar 1:4 set and jointed with grey cement slurry mixed with pigment to match of the slab including rubbing and polishing complete all as specified and directed by Engineer - in - Charge.

Material and labour 16-18mm thickness approved shade granite of minimum size equal to width of slab (not less than 600mm wide, length wise single or two pieces only) machine cut, granite duly factory grinding and polishing and chamfering the outer edges (table rubbed and mirror polished) as in cooking platform and like laid over and including 20mm thick cement mortar (1:4) screed bed including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including accomodate the hole for gas pipe complete all as specified and as directed by Engineer-in-Charge

Taking down chowkats or frames with shutters (with out taking off shutters from the frame) not exceeding 1.50 Sqm each complete all as specified and directed by Engineer - in - Charge.

Taking down chowkhats or frames with shutters without taking off shutters from the frame exceeding 1.5 Sqm but not exceeding 4 Sqm each and complete all as specified and directed by Engineer - in - Charge.

Taking down and refixing of shutter in same opening but area exceeding 1.00 Sqm and not exceeding 2.0 Sqm complete all as specified and directed by Engineer - in - Charge.

Taking down shutters but area exceeding 1.00 Sqm and not exceeding 2.0 Sqm complete all as specified and directed.

S & F pressed steel door frames size of 125X60mm thickness of sheet shall be 1.25 mm with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete all as specified and directed by Engineer - in - Charge.

S & F pressed steel door frames size of 105X60mm thickness of sheet shall be 1.25 mm with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete all as specified and directed by Engineer - in - Charge.

M&L Cement concrete 1:3:6, type C-1, using 20mm graded stone aggregate for filling of pressed steel frame, post hole and hold fast blocks etc complete all as specified and directed by Engineer - in - Charge.

S & F Factory made Plain framed, panelled shutter IInd class hardwood rail and style 35 mm thickness (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer - in - Charge.

S & F Factory made 35mm thick IInd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; size of members of shutters as specified in SSR Part – I, Section – 8, clause 8.20 (a) ; supplied and fitted to chowkats complete all as specified and directed by Engineer - in - Charge.

S & F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm all as specified and directed.

Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame., complete as specified by the manufacturer and as per directions of Engineer-in-charge.

Supply and fixing to existing door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer- in-charge.

S & F 100 mm Butt hinges, stainless steel butt hinges, and fixed with steel scerws for wooden doors, complete all as specified and directed by Engineer - in - Charge.

S & F tower bolt 200 mm of aluminum complete all as specified and directed by Engineer - in - Charge.

S & F door handle D type 150 mm of aluminium complete all as specified and directed by Engineer - in - Charge.

S & F Aluminium alloy, anodised, sliding door bolt 300mm with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S & F mild steel 300mm ordinary rat rail rod pattern spring inluding roller and roller plate complete all as specified.

S&F Floor door stopper of aluminum allow body and tongue, 150mm overall length, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F peg set of stainless steel solid body of 125mm to 175 mm having 6 Nos hooks fixed with brass chromium plated screws complete in all as specified.

S& F in repairs curtain rod 25 mm dia MS pipe with ivory coloured PVC coasted, wall thicknes of pipe not less than 20 guage, including fancy type brackets and pair of decorated end knobs (finials), stop roller etc. as per site requirement, fixed to wall with fixing accessories, complete all as specified and directed by Engineer - in - Charge.

S&F powder coated aluminium sliding window three track with frame & two glass shutters using 4 mm thick glass tinted and one shutter with stainless steel wire gauge wire cloth 0.31 mm nominal dia of wire and width of aperture 1.61mm using aluminium powder coated section aluminium cleat, PVC track, bearing, handle lock rubber beading etc complete fittings as approved. Note :- Size of aluminum section shall be under – (i) Three track top and vertical –jindal main-2010 section No 20621 or equivalent as approved by GE. (ii) Three track bottom-Jindal main-2010 section No 20620 or equivalent as approved by GE. (iii) Shutter vertical section-Jindal main-2010 section 20604 or equivalent as approved by GE. (iv) Shutter top and bottom –Jindal main – 2010 section 20604 or equivalent as approved by GE. (v) Shutter vertical middle (interlock) – Jindal main – 2010 section 20605 or equivalent as approved by GE. Note : Cost of glass and wire cloth will be included in quoted rate.

S&F for powder quoted Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

Supply & fixing anodised aluminium window shutter (glazed or gauzed), side and top hung type without sash bars, made out of aluminium section weighing not less than 0.55 Kg/mtr, powder coated (minimum thickness of powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings (each shutter) such as peg stays 150mm long (1 No), hinges type B-21 100mm long (2 Nos) suitable handle (1 No.), complete all as specified and as directed by Engineer-in-Charge. Note :- Aluminium chowkhat/ frame, Glass, wiremesh and grill where required shall be measured and paid separately under appropriate item of BOQ

S&F aluminum powder coated grill weight not less than 1.50 Kg /sqm in window, doors or ventilators including fixing material complete all as specified and directed by Engineer-in-Charge.

S & F 4 mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.50 sqm in each pane all as specified.

S & F figured glass 4 mm thick pin head type and glazing with oil putty and securing with glazing pins not exceeding 0.50 Sqm in each pan complete all as specified.

M & L Washed stone grit plaster on exterior walls in two layers under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per sqm, top layer 15 mm cement plaster 1:1/2:2 (1 cement : ½ coarse sand : 2 stone chipping 10 mm normal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to be expose the stone chippings complete all as specified. Note : Payment for providing grooves shall be made separately.

Forming groove of uniform size 15 mm wide and 15 mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden batterns, nailed to the under layer including removal of wooden batterns, repair to the edges of panels and finishing the groove complete as per specification and direction of the Engineer-in-Charge.

Dismantaling boarding, any description fixed in any position with nails.

Material and labour for providing kitchen cabinet and cubboard in required sizes at site made out of 18mm thick PVC sheet (prelam) having one side decorative laminated sheet (for shutter, back side of cabinet, sides of cabinet, partition and shelves etc). All the edges of shutter and front exposed edge of partition/shelves shall be covered with 2mm thick edge bonding tape as per manufacturer. Including all required fixing material such as SS brackets, screws, adhesive etc., including taking out old any type cabinet complete all as specified and as directed by Engineer-in-charge. Note :- (i) The area of each sheet (shutter, back side of cabinet, sides of cabinet, partition and shelves) shall be measured in sqm for payment. (ii) Magnetic catcher, handles, continuous Piano hinges and PVC frame (where required) shall be measured and paid separately under appropriate item of BOQ. (iii) Any other material required for making/fixing/hanging of cabinet shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account.

S&F magnetic catcher fixed with nut screw and washer complete all as specified and directed by Engr-in-charge.

S&F extruded brass handle fabricated type 100mm long cabinet fixed with steel screw complete all as specified and directed by Engineer -in - Charge.

S&F Continuous (piano) hinges, stainless steel, bright finish, width of flap when open 30mm complete all as specified and directed by Engineer -in - Charge.

S&F Factory made prefabricated pressed steel door frame made out of mild steel minimum 0.90 mm thick grith of frame 185 mm including necessary MS rawl plug/bolts and fixing 75 mm long butt hinges medium weight cold rolled mild steel etc and shutter including stiffeners made out of mild steel sheet minimum 0.90 mm thick cut to size, holes punched and welded seams including bending or turning up all around, mitred angle etc as required with locking arrangement uing mild steel mortise lock 4 leavers with 2Nos of keys of size 100 mm including MS chromium plated handle and 2 Nos MS locking rods out of 8mm dia not exc 1000mm long fixed to mortise lock and handle with necessary bolts and nuts covered by MS sheet minimum 0.90 mm thick complete including two coat of synthetic enamel paint over a shop coat of zinc chromate primer on interior surface (not visible from front) and hammer tone paint on exterior surface (visible from front) complete as per Godrej Pattern all as specified and directed by Engr-in charge drawing complete all as specified and directed by Engineer - in - Charge.

M & L providing two coats of synthetic enamel paint over new surface and a coat of red oxide primer on steel surfaces including preparation of surface of any description not exceeding 10 cm width or girth all as specified.

Dismantling wrought iron or mild steel work of any description all as specified.

S & F structural steel work rolled mild steel joist, channel, angle or Tee sections, fixed independently conforming to Fe 410-W all as specified.

S & F exc 12 mm dia & n. exc 20 mm dia of neck mild steel bolts purpose made with hexagonal or square head one and end and screwed to other, or screwed to both ends each screwed end to be fitted with washers and one hexagonal or square nut exc 30 cm long.

S & F framed work such as grills, cooler stand ,grating, etc., with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work or water tanks and similar work conforming to Fe 290.Gde -E- 165 all as specified.

Material and labour for water proofing treatment to sunken slab and adjoining vertical surfaces as per any of the following method complete all as directed by Engineer-in-charge/GE. :- Method 1 (A) Supplying and applying two component elastomeric acrylic polymer modified cementitious waterproofing coating, Smart Care Damp proof 2K, having 100% elongation as per ASTM D412, resisting 5 bars hydrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per DIN 1048, crack bridging upto 1.2mm as per ASTM 4548.5 Clean all working surface & made free from dirt, grease laitance etc. After inspection for all working area rough surface, cracks & construction joint are treated by polymer modified mortar of 1:1:4 (1 Cement : 1Polymer : 4 Sand). Making Gola of size 75x75mm at junction of vertical & horizontal with the polymer modified mortar of 1:1:4 (1 Cement : 1 Polymer : 4 Sand). The mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing and shall have consumption of 1.5kg/sqm per coats, etc, complete as per manufactures specifications. (B) Bore Packing : All the borehole gaps between concrete surface and pvc pipe of various diaupto the neck level shall be filled with non-shrink free flow grout – Smart Care GP Grout or approved equivalent having dual shrinkage compensation property. Before the bore packing, surface of the pvc pie and concrete surface will be made rough and sand will be sprinkled with polymer bonding agent. (C) Apply12-15mm plaster on slab and vertical surface admixed with Smart Care Vitalia Neo @200ml per bag of cement.

Method 2 (A) Supplying and applying two component cementitious& acrylic flexible water proofing & protective coating, two coats with 1mm DFT, having Hydrostatic (positive) water pressure resistance (DIN 1048) is 7. Abrasion resistance, cm/km is 0.09 of Dr FixitPidifin 2k @ 1.5kg/sqm with a paint brush over existing roof surface. The Polyester reinforced coated net of 45g/sqm, 2.5mmx2.5mm is laying on the surface immediately on the first coat of two component modified polymer Dr Fixitpidifin 2k or equivalent. After removal of all lose materials like dust etc. with wire brush coir brushes from roof surface to get absolutely cleaned surface free of foreign contaminant filling of crack and patches with polymer based repair mortar/micro concrete, after the repairing work making the gola on surrounding wall’s junction and seal the vertical walls. In case of core cutting on the surface, the joint is seal with non-shrink grout. (B) Apply12-15mm water proof plaster on slab and vertical surface admixed with Dr Fixitpidiproof LW+ @200ml per bag of cement before treatment. Make : Method 1 (Asian paint)/ Method 2 (Dr fixit) or Techno commercial equivalent in Fosroc/Sika/STP”

Providing 100mm cement concrete Type E-2, 1:5:10, (40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

S&F in repair sink with drainage bord made of Stainless Steel 1mm thick kitchen with plug washer and waste including bedding in cement mortar to dwarf wall including fixing contilever brackets connecting union to pipe over all size 915x460 mm bowl of size 410 x 330 x 160 mm complete all as specified and directed.

S&F Stainless steel plate rack of size 750mm x 600mmX 250mm, made out of 1mm thick stainless steel of sheet of 1st quality complete all as specified and directed by Engineer -in -charge.

S & F repair vitreous china squatting pan Orrisa pattern size 580mm x 440mm white with integral foot rest with CI ‘P’ or ‘S’ trap and fixing in lime concrete (1 lime, 2 sand and 5 aggregate), 150mm thick all round and finished just below level of rim of pan to receive the floor finishing all as specified.

S & F in repairs PVC 10 ltrs syphonic action type flushing cistern, low level with inlet, ball valve, float and handle including brackets, flush pipe of PVC 32mm bore and connection to WC pan complete all as specified.

S & F vitrous china oval corner wash hand basin white of small size 450X390 mm including brackets 300mm long PVC connection with brass nuts, 40mm dia waste coupling including cutting for and pinning in end of brackets or erecting stand etc coloured top bowl type screwed shank fly nut flange end including cutting for and pinning in granite slab of hole including 32 mm dia chromium plated waste coupling and bottle trap all as specified.

S&F in repair 15mm bore bib taps,chromium plated, fancy type, cast copper alloy with crutch or butterfly handle , screwed down, secrewed for iron pipe or for brass ferrule complete all as specified and directed by Engr-in- charge.

S & F in repairs 15mm bore Angle cock chromium plated fancy type , high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified.

S & F pillar taps 15mm bore fancy type chromium plated cast copper alloy with capstan heads scre-wed down high pressure with or without lettered hot' or'cold' with long screwed shanks and fly nuts screwed for iron pipe ISI marked.

S&F Sink mixer with swinging spout(wall mounted model)Chromium plated brass with connection and nut complete all as specified and directed by Engr-in-charge.

S&F brass chromium plated wall mixer for mixing hot& cold water screwed down for iron pipe and fixed as directed by Engr-in- charge.

S & F in repair PVC connection 15mm size with PTMT nuts of length 450mm all as specified.

S&F PVC bathroom cabinet mirror 450 x 350 mm complete all as specified and directed by Engr-in-charge.

S&F Swivel shower of Chromium plated any colour with shower arm 15 mm size 195 mm long with bend of 45 degree with flange of any colour for fixing with 15mm pipe. Note : Minimum weight 400gms.

S & F soap dish vitreous china white approximately size 160 x160x 90 mm and fixed with as chromium plated brass screws complete all as specified and directed by Engineer -in -charge.

Supply and fixing chromium plated Towel Rail (Single) 600/610mm long between flanges including bracket, fixed on wall with chromium plated brass screws and PVC plug complete all as specified and as directed by Engineer-in-charge.

Supply and fixing corner Glass shelf including chromium plated bracket and guard railing fixed on wall with chromium plated brass screws and PVC plug complete all as specified and as directed by Engineer-in-charge.

Taking down steel tubing 15mm bore and connections complete all as specified.

Fixing only tubes any grade 15mm bore to walls and ceiling or in floors etc including provision of new fittings as required (Serviceable galvanised tubes retrieved from respective items shall be laid under these items) all as specified.

S & F 15mm bore medium grade tube galvanised with all fittings and fixed complete concealed including groove cutting for concealing to walls & ceiling or laid in floor all as specified.

Taking down steel tubing 20mm bore and connections complete all as specified.

Fixing only tubes any grade 20mm bore to walls and ceiling or in floors etc including provision of new fittings as required (Serviceable galvanised tubes retrieved from respective items shall be laid under these items) all as specified.

S & F 20mm bore medium grade tube galvanised with all fittings and fixed complete concealed including groove cutting for concealing to walls & ceiling or laid in floor all as specified.

Dismantling of water tanks of 500 ltrs and removing to store complete all as specified and directed.

S & F rotational moulded polythene three layered white coloured water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I of capacity 500 Litres all as specified and directed by Engineer - in - Charge.

M&L Ball brass valves 20mm, high pressure, with polythene float and fly nut complete, screwed for iron pipe complete all as specified and directed.

S & F 20mm bore gunmetal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed all as specified.

Taking down CI/AC/PVC soil waste and vent pipe any radius including all fittings complete.

S & F PVC socketed SWR pipe with rubber ring joints 110mm dia fixed to wall complete all as specified.

S & F PVC socketed SWR pipe and pressure rating not less then 6kg/f /sqcm with rubber ring joints 75mm dia fixed to wall complete all as specified.

Supply & fixing 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints for drain or rain water laid in trenches /under floor complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints for drain or rain water laid in trenches /under floor complete all as specified and as directed by Engineer-in- charge.

S&F for 110mm bore PVC (SWR) bends any radious provided with access door (Pressure not less than 6kg/cm2) complete all as specified and as directed by Engineer-in-Charge.

S&F for 75mm bore PVC (SWR) bends any radious provided with access door (Pressure not less than 6kg/cm2) complete all as specified and as directed by Engineer-in-Charge.

S & F PVC(SWR) 100 mm bore vent cowls complete all as specified and directed by Engr-in-charge.

S & F PVC(SWR) 75 mm bore vent cowls complete all as specified and directed by Engr-in-charge.

S&F for 75 mm bore PVC (SWR) multi floor trap with SS grating including jointing with solvent cement.

Taking down cement plaster/dado on brick wall including racking out joints, hacking for keys scrubbing down with water all as specified.

M & L rendering 15mm thick on fair faces or other than fair faces of brick work in CM 1:6 finished even & smooth without using extra cement all as specified.

M & L Rendering 15 mm thick on fair faces of brick work or concrete surfaces, in cement mortar (1:4), with using water proofing compound @ 3% as per manufacturer's instructions, surfaces finished even and smooth without using extra cementcomplete all as specified. Note : Cost of water proofing compound shall be included in quoted rate.

M&L for Shotcreting 25MM thick in RCC columns, beams and slabs etc in layers with approved design mix (minimum cement content of 350 Kg/Cum on M-25) concrete having the specified minimum characterristic compressive strength (with ordinary protland cement, coarse sand and graded stone aggregate of 10 mm maximum size in proportion as per design criteria) including the cost of certering and shuttering at edges and corners etc as directed by Engineer-in-Charge including Chipping of unsound /weak concrete material 25 mm average thickness from slabs,beams, columns etc with manual chisel and /or by standred power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes and thoroughly washing with water and allowing it to dry etc. including removal of rust by applying approved rust removal chemical & the coating with Dr Fixit epoxy zinc primer@ 6sqm/ltr at DFT of 100microns as per specifications and disposal of debries for all lead and lifts all complete as per direction of Engineer-in-Charge.

S&F Hard drawn steel wire fabric not exc 4Kg/Sqm cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcemnt all as specified & directed by Engineer-in-Charge.

M & L 5mm thick rendering in Cement Mortar 1:3 on fair faces of brick work or concrete surfaces of ceiling finished even and smooth without using extra cement complete all as specified and directed by Engineer - in - Charge.

Providing & applying Rising damp proof coating system with single component ready to use damp-proof coating Roff Hydamp: 1. SURFACE PREPARATION:Thoroughly brush and clean all laitance,loose particles such as dirt,grease,mortar droppings,release agents,efflorescence,bird droppings etc. all large voids or hollow portions must be removed and replastered.Non-moving cracks having width upto 5 mm must be filled with polymer based crack filler. 2. APPLICATION: Apply the first coat of Hydamp with paintbrush directly on the prepared surfaces.Allow to dry for a minimum 2-3 hrs.Apply one part of Roff Hydamp and 2 parts of OPC white cement and make the putty,apply putty on the entire surface area.Allow it to dry for atleast 3-4 hours.Apply the final coat of Roff Hydamp on the entire surface.

M & L applying three coats of white wash on newly plastered or unplastered ceiling surfaces including preperation of surfaces, complete all as specified.

M & L Preparation of newly plastered wall surfaces and applying three coats of white wash including preparation complete all as specified and directed by Engineer -in -charge.

M & L two coats of white wash on old decorated plastered or unplastered surfaces of walls including preparation of surfaces all as specified and directed by Engineer - in - Charge.

M & L Preparation of newly plastered surfaces by applying two coats of interior grade wall putty and making it smooth with sand paper by mechanical method i.e. with hand electric grinder then applying two coats of Acrylic distemper over one coat of cement primer including all as specified by mechanical method i.e. spray gun all as specified and directed by Engineer-in-charge.

M & L Preparation of Old plastered surfaces by removing old treatment and applying two coats of interior grade 1mm wall putty and making it smooth with sand paper by mechanical method i.e. with hand electric grinder then applying two coats of Acrylic distemper over one coat of cement primer including all as specified by mechanical method i.e. spray gun all as specified and directed by Engineer-in-charge.

M&L for preparation of two coats of cement base paint over a coat of alkali resistant primer on newly plastered surface complete all as specified and directed by Engr-in-charge.

M&L for Complete removal of old plastered wall surfaces and applying two coats of cement base paint over a coat of alkali resistant prilmer complete all as specified and directed by Engr-in-charge.

M & L providing two coats of synthetic enamel paint over new wooden surface including preparation of surface with pink primer all as specified.

M & L providing two coats of synthetic enamel paint over new steel surfaces and a coat of red oxide primer on including preparation of surface of any description not exceeding 10 cm width or girth complete all as specified and directed by Engineer -in -charge.

Excavation trenches n exc 1.50 wide and n exc 1.50 m depth for foundation etc in any type of soil complete all as specified and directed.

Returning filling in including spreading leveling, watering and well ramming in layers n exc 25 mm thick soil complete all as specified and directed.

Removing excavated material n exc 250 m and deposited where directed at a level not exc 1.50 m above the starting point.

M&L Providing cement concrete Type D-2, 1:4:8 (40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

Material and labour for mild steel framed work, framed/truss work made by using hollow square/rectangular/round pipe (ERW or induction butt welded tubes conforming to latest relevant IS), including special shaped washers, bending and welding etc, complete all as specified and as directed by the Engineer-in-Charge.

S&F 50mm thick PUF panel made of Puf insulation in core having density 40+2 Kg/Cum sandwiched betweeen two numbers of polyster coated galvalume steel sheet, these sheets shall be made out of 0.50mm thick (TCT) High tensile steel having min yield strength of 550 Mpa confirm to AZ 150 of AS-1397 with hot dip metalic coating of 55% ZN alloy having total coating mass of minimum 150 gms/sqm inclusive of bothside. the material shall be coated with polyster coating paint system of 20 micron over primer of 5 micron (exposed side) & alkyd back coat of 5 micron over primer coat of 5 microns.the material shall be supplied as per drawing (approved by GE),colour and as per instruction complete all as specified and directed by Engineer-in-charge.

S&F Anodised aluminium snap grid frame work for false ceiling Size of Grid 605 x605 mm with 6mm dia GI wire hanger ( upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3 mm size 60 mm long Complete all as specified and directed by Engr-in -Charge.

S&F,7 to 8 mm thick exposed metal frame celing with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600mmx600mm grid all as per manufacturer's instructions. finish, fixed to aluminium/ CGI frame work with hold down clips in false ceiling complete all as specified.

M& L for Pre painted gavalume zinc coating GI based plain steel sheet 0.50mm thick for ridge ,hip,vally gutter ,drips of an colour having tensile strength of 550 Mpa as in wall,fixed with self tapping screws complete all as specified.

M& L for Pre painted gavalume zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof coverings/cladding to wall,fixed with self tapping screws complete all as specified.

M& L PCC 1:2:4 type B1, using 20 mm graded agg.as in bed blocks ,coping, hold fast blocks etc.

M&L PCC 75 mm thick, PCC 1:4:8, type D-2, (using 40mm graded stone aggregate) as in sub base complete all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L for contineous brick edging with burnt clay brick work with sub class ‘B’ with width equal to width of brick laid dry on end vertically.

S & F 15mm bore stop valve, cast copper alloy fancy type chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed.

Taking down carefully point wiring complete including fixture and fittings from boards/outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators, etc. and making good to disturbed area all as specified.

M&L for Point wiring complete with ISI marked 1.5 sqmm single core PVC insulated unsheathed cable 1100V grade FRLS with multistranded copper conductor drawn through concealed in wall/ceiling surface and its accessories including PVC rigid concealed conduit heavy duty suitable size with all accessories such as bend, reducers, MS hooks, MS junction boxes, 2mm thick galvanised steel pressed sunken terminal boxes of suitable sizes for mounting of switchs, sockets, fan regulator etc covered with 3 mm thick plastic laminated Hylem top cover sheet of required color fixed with brass screws and cup washers painting terminal boxes inside and outside with one coat red oxide primer including fixing and 1.5 sqmm copper conductor as earth continuity to connect common earth dolly completed for the following all as specified.

One light point/Fan point/Exhaust/bell point controlled by one way switch.

One light point controlled by one two way switch.

One 5 pin socket out let 5 amps on the same board with other switches.

One 5 pin, 5A switch socket outlet point on independent board.

All as per Ser item No 141.00 above but with 2.5 sqmm cable for 1No 16 amps socket outlet point on independent board including 2.5 sqmm PVC insulated unsheathed cable multistranded with copper conductor green in colour as earth continuity conductor all as specified.

All as per Ser item No 141.00 above but with 4.0 sqmm cable for 1No 16 amps socket outlet point on independent board including 4.0 sqmm PVC insulated unsheathed cable multistranded with copper conductor green in colour as earth continuity conductor all as specified.

M&L in repair of submain wiring with two single core PVC FRLS insulated copper conductor 6 sqmm and same 6 sqmm for continuous earth wire drawn in to suitable concealed PVC conduit complete all as specified. Note : Two run of wire and one run earth wire and PVC conduit shall be measured as one unit.

Supply and fixing in replacement of LED complete fitting including batten, T8 retro LED polycarbonate 1 x 20 Watt, appx 4 feet long, environment friendly, including electric connection with using 2 core flexible copper conductor cable 23/0.00076 from ceiling rose to tube fitting, complete fitting with all accesssories and following specifications, including taking down old unserviceable light fitting any type complete all as specified and directed by Engr-In-charge.

Supply and fixing in replacement of LED tube light fiting 1x10W, (appx 2 feet long) environment friendly including electric connection with using 2 core flexible copper conductor cable 23/0.00076 from ceiling rose tolight fitting, complete fitting with all accessrries and following spcifications including taking down old unserviceable light fitting any type complete all as specified and directed by Engr-In-charge.

Supply and fixing complete set of 1x10 watt LED retrofit type bulkhead fitting luminaries die cast aluminium alloy body heat resistant prismatic glass cover with specially designed gasket lamp holder etc complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size including taking down old Unserviceable light fitting any type as specified.

Supply and fixing in replacement energy efficient LED street light fitting of 25W pressuire die cast aluminium housing/body heat resistant clear toughened glass, better optics for uniform distribution street/road way luminaire with driver including electric connection complete fitting with all accessories and following specifications, including taking down old unserviceable light fitting any type complete all as specified and directed by Engr-In-charge.

Supply and fixing in replacement LED bulb 1x9 Watt lamp having luminous efficancy, BEE rated LED Lamps and warranty 2 year all as specified and directed.

Supply and fixing in replacement PVC Angle Lamp holder polycarbonate type with back plate suitable for LED blub up to 9 watt complete all as specified.

S&F in replacement Piano type switch single pole 1 way 5/6 amps 230 volt AC supply complete all as specified.

S&F in replacement socket two in one 6/5 Pin 5 Amps 230 volt AC supply complete all as specified.

S&F in replacement Piano type switch single pole 1 way 15/16 amps 230 volt AC supply complete all as specified.

S&F in replacement Piano type switch single pole 2 way 5/6 amps 230 volt AC supply complete all as specified.

S&F in replacement bell push flush type 5 amps complete all as specified.

S&F in replacement Bell ding dong AC 230V single pole complete all as specified.

S&F in replacement socket two in one 6/5 Pin 15/16 Amps 230 volt AC supply complete all as specified.

M&L in replacement ceiling rose surface type, 65mm x 50mm three terminals, 3 phase / PVC / polycarbonate isolated body all as specified.

Supply and fixing in replacement ceiling fan regulator, stepped type of 0 to 04 rotary steps, electronic, socket type, humfree, AC, 230 volts, 100 watts, duly ISI marked with and including white surround complete all as specified & directed.

Supply and fix LT Main control board of CRCA sheet metal board made out of 2.0mm thick and painting with 2 coats with synthetic enemel paint over a coat of red oxide primer including copper bus bar and fixed on/inside wall for fixing arrangement of existing electronic meter incl internal connection with suitable size of copper conductor wire, and accessories, locking arrangement with opening handle (size not less than of box 100cmx80cmx25cm and adequate depth for the following equipments,internal wiring and termination of external cables, lugs and glands and conduit as required) including Taking down existing Old Unserviceable main control board comprising of following :-

Incoming :- MCCB 100 Amps, 4 Pole,415 Volts, 16 KA-01 No

Copper Bus bar 200 Amps for phase and neutral and earth bar

Out going MCB SPN 40 Amps - 4 Nos

Out going MCB SPN 10 Amps - 1 No

S&F in replacement sheet metal enclosure for DB's SPN 230 volts 12 way with 200 amps rated bus bar neautral link, earth bar double door complete all as specified.

Supply and fixing in replacement 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified.

Supply and fixing in replacement amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of SPN 32 AMP and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified.

Supply and fix exhaust fan heavy duty 300mm sweep 230/240 volts single phase with made of steel body complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding complete including provision of cutting walls suitable for fixing exhaust fan and necessary plastering and making good distured surface to match the existing complete all as specified.

Supply and laying in replacement cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3½ core complete all as specified.

M&L for PCC preparation including cutting up to 45 cm width and depth of the road/hard standing and making good disturbed surfaces by using PCC type C2, (1:3:6) by using 40mm graded stone aggregate for the fixing the pipe/laying cables complete all as specified.

M&L in replacement for 50mm dia steel tubes (light grade) galvanised with fittings, laid in trenches/wall for protection of underground earth strip when crossing the road/fixing on wall as in repair complete all as specified and directed.

Earthing complete with galvanised steel earth plate electrode of size 60 cm X 60 cm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 m below normal GL connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers and earth strip protected by 15 mm dia GI pipe medium grade and connected to main distribution board panel/earthing test point all as shown on electrical plate No.3 of SSR Part I and all as specified including testing on completion including taking down old Unserviceable earthing any type all as specified.

M & L for wiring for inverter socket outgoing to DB with 1.5 sqmm single core FRLSH standard copper conductor for point wiring already catered in point wiring all as specified.

S & F plug top 5/6 Amps 3 pin good quality suitable for 240 volt, AC supply for inverter socket all as specified.

M&L for Sand filling under flooors, in trenches or in foundation for cable protection including and consolidation as as specified and directed at site.

Boring of holes under road, pavement, hard standing by trenchless technology usingn ultra sound technique and necessary machine including HDPE pipe of 150 mm dia suitable for 0.4 mpa working pressure.

S&F un-reinforced precast concrete cable cover class LV, type I, flat, size 250 mm x 150 mmx40mm laid flat length of cover across the length of cable a complete all as specified and directed by Engr-In-Charge.

Supply and fixing plug and socket type DB (Functional unit) 20 Amps capacity with provision of single pole 20 Amps MCB, plug top and earth plug, grouted flush to walls and necessary cement work for make good as existing to all disturbed surface complete all as specified.

CHILLANA CONSTRUCTION COMPANY

SHRI SHYAM CONSTRUCTION CO.

Ramdev Enterprises

RANDHIR AND COMPANY