SPECIAL REPAIR TO BLDG NO P 40 A1 COOK HOUSE BLDG NO P 13 AND DRAINAGE NEAR BLDG NO P5 P7 AND P9 IN THE AOR OF AGE B/R II UNDER GE NARANGI

Amount

Excavating in post holes (or similar holes) each not exceeding 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surfaces in soft/loose soil complete all as specified & as directed.

Excavation in trenches n.exc 1.5m wide and not exceeding 1.5 m in depth for foundation etc, or for shafts, wells, cess pits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in soft / loose soil etc complete all as specified and as directed.

Returning, filling including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each in soft / loose soil etc complete all as specified and as directed.

Removing of surplus excavated material not exc 50m and depositing where directed at a level n. exc 1.5 m above the starting point etc complete all as specified and as directed.

M&L for hardcore of broken or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface etc complete all as specified and as directed.

M&L PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) in foundation filliing and mass concrete complete all as specified and as directed.

M&L PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in coping, benching including necessary formwork and finishing of exposed surfacs of concrete etc complete all as specified and as directed.

M&L for RCC 1:2:4 type B1(20mm graded stone aggregate) nominal mix as in Foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under-reamed piles and mass concrete etc complete all as directed.

M&L for RCC 1:2:4 type B1(20mm graded stone aggregate) nominal mix as in Slabs supported on walls beams and columns in floors,roofs,landings, balconies,canopies,deck slabs and in shelves and the like etc complete all as specified as directed.

M&L for RCC 1:2:4 typeB1(20mm graded stone aggregate) nominal mix as in beams, seimic bands, cantilevers, bressumers and lintels complete all as specified as directed.

M&L for RCC 1:2:4 type B1(20mm graded stone aggregate) nominal mix as in Columns, pillars, piers, posts and struts etc.complete all as specified as directed.

M&L PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) in surface channel and drain complete all as specified and as directed.

M&L extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and directed.

Supply and lay Reinforced concrete pipes 600 mm bore of pipe class NP2 laid in trenches and jointed complete with collars etc complete all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

M&L for brick work with old size sub class 'B' bricks straight or curved on plan exc. 6m mean radius and built in CM 1:6 etc complete all as specified as directed.

All as per item No.16 Above but except bricks. ( Serviceable bricks shall be obtained from demolition of brick work here in before).

M&L for brick work with old size sub class 'B' bricks straight or curved on plan exc. 6m mean radius and built in CM 1:4 etc complete all as specified as directed.

M&L for brickwork with subclass ‘B’ old sized bricks, straight or curved on plan to any radius in half brick thick walls and built in CM 1:4 etc complete all as specified as directed.

M&L for brick work with old size sub class 'B' bricks laid flat in floors bedded and jointed in cement mortar 1:6 and pointed in cement mortar 1:3 complete all as specified as directed.

M&L for brick work with old size sub class 'B' bricks laid on edge in floors bedded and jointed in cement mortar 1:6 and pointed in cement mortar 1:3 complete all as specified as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified as directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; n. exc 200m thick (Horizontal or sloping) complete all as specified as directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified as directed.

Formwork to sides of pillars, posts, struts, piers, columns, and stanchions complete all as specified as directed.

Dismantling timber scantlings 40 sq. cm and over in section (unframed work), in any position complete all as specified & as directed.

M & L second class hard wood scantling fixed in clean sawn timber in framed work complete all as specified and as directed

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area not exceeding 1.5 Sqm each including builders hardware complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5 Sqm but not exceeding 4 Sqm each including builders hardware complete all as specified and as directed.

S&F 35mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc (with out sash bar), edges of framing with plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters all as specified in SSR part-I section 8 clause 8.24 (a) complete all as specified and directed.

S&F 30mm thick second class hard wood glazed and skeleton shutters, open rebated divided into square and prepared to receive glass, gauge etc (with sash bar of any number), edges of framing with plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters all as specified in SSR part-I section 8 clause 8.24 (b) complete all as specified and directed.

M&L for 1.25mm thick factory made pressed steel frames of size 105x60mm with single rebates including necessary fixing lugs, hinges, lock strike plate, etc complete including PCC 1:3:6 type C-0 as in back filling of window/door frame all as specified and directed.

M&L for 1.25mm thick factory made pressed steel frames of size 125x60mm with single rebates including necessary fixing lugs, hinges, lock strike plate, etc complete including PCC 1:3:6 type C-0 as in back filling of window/door frame all as specified and directed.

M & L for PCC 1:3:6 type C-1 ( 20mm graded aggregate) as in bed block or hold fast including making good surfaces complete all as specified and as directed.

S&F 30 mm thick flush shutter, solid core construction with particle board core and plywood face panel, commercial type on both side complete all as specified and directed.

S&F factory made steel window with side hung shutters, glazed shutter including both side openable ( outside glazed window and inside fly proof window) including projecting type hinges with steel handle and steel peg stay complete with glazing bars and 12mm square bars or round bars of approved design welded to steel window frame dovetailed or welded complete all as specified and directed. (Guard bars or square bars shall be measured and paid seperately).

S&F powder quoted three track aluminium sliding window with approved make of following extruded section of anodised glazed shutter as per standard engineering practice including all accessories complete with 4.00mm thick tinted glass panes, rubber beading , mosquito proofing, locking system etc complete all as specified and directed. (i) shutter bottom and top - 37.50X15X1.3mm thick (20690) . (ii) shutter interlock-- 37.50X23X1.3mm thick (20689). (iii) shutter side ( handle) -- 37.50X23X1.3mm thick (20689).. (iv) frame bottom--75X26X1mm thick ( 20672). (v) frame top and side--75X26X1mm thick ( 20672). Make Jindal Cat M-2014. Aluminium sections A series.

S&F powder quoted anodised aluminium push , pull typ partly psnelled and partly glazed door shutter ( single leaf/double leaf) having top rail of section 85.00mmX 44.45mmX 2.00mm thick, bottom rail of section 85.00mmX 44.45mmX 2.00mm thick, door vertical of section 44.45mmX44.45mmX 2.00mm thick and lock rail of section.85.00mmX 44.45mmX 2.00mm thick with aluminium anodised chowkhat of section 63.50mm X 33.10mm X 2.50mm thick including necessary jointing clips, glazing clips, rubber packing, snap beading, screws, handle and locking arrangement etc, including 12mm thick prelaminated particle board, interior grade prelaminated with decorative face lamination on both sides on bottom panel and 5.50mm thick float glass tinted quality on top panel complete all as specified and directed.(Note: Door closure shall be measured and paid seoerately) .

M&L in repair for seccond class hard wood weather boarding , clean sawn, plain 19/20mm thick or feather edged 15/20mm thick and fixed with 30mm laps complete all as specified and as directed.

S&F 30 mm thick Factory Made Solid Panel PVC Door Shutter consisting of frame made out of M.S. tubes of 19mm x 19mm for stiles, & 15mm x 15mm for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC sheet 5mm thick ‘C’ channel having a 5mm thick PVC sheet strip of 20mm width stuck inside with solvent cement, forming stiles, and plain colour PVC sheets for top rail, lock rail & bottom rail on either side, and as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with PVC sheet beading, and joined together with solvent cement adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s instructions and drawing. The width of stiles & rails will be in proportion to the width of the door shutter as per SSR Clause No 8B.2.1

M&L for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing etc complete all as directed.

S&F 150 mm size aluminum anodised, barrel tower bolts of extruded section etc complete all as directed.

S&F 100 mm size aluminum anodised, barrel tower bolts of extruded section etc complete all as directed.

S&F aluminum alloy anodised, sliding door bolts with hasp and staple, (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolt and sliding bolts of extruded section or cast aluminium alloy and fixed 300mm long etc complete all as specified and directed.

S & F 100mm size Butt hinges, medium weight, cold rolled mild steel, and fixed etc complete all as directed.

S & F 75mm size Butt hinges, medium weight, cold rolled mild steel, and fixed etc complete all as directed.

Supply and fix steel helical door spring 300 mm size rat tail rod pattern spring, including roller and roller plate complete all as specified and directed.

S&F 150 mm long extruded anodized aluminum alloy handles, cast type, etc complete and directed.

S&F 100 mm long extruded anodized aluminum alloy handles, cast type, etc complete and directed.

S&F Aluminium body ( extruded section) Door closure hydraulically regulated designation no.3 universal type suitable for door shutters of 851to 1000mm in width and weight between 61 to 80 Kg and fixed complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as directed.

S&Fin repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as directed.

Dismantling of asbestos cement (corrugated,semi corrugated, etc.) sheets in roof coverings including ridge complete all as specified & as directed.

M&L Pre- painted hot dip aluminium Zinc alloy metalic coated trapezoidal profile steel sheet 0.50mm thick ( Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screws complete all as specified and directed.

M&L Pre- painted hot dip aluminium Zinc alloy metalic coated plain steel sheet 0.50mm thick ( Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screws as specified complete all as specified and directed. Note: To be executed for provision of ridges and hips.

S&F in repairs, suspended false ceiling using E-grid 2430, 180 GSM (exposed ceiling suspension system ) of grid size 600mmx600 mm with main runner 38 mm x 24 mm and wall angle 24mm x 24mm using 4mm thick High Pressure stean Crude Everest Non Asbestos Fiber Cement designer Board (E-Board Classic) in & including a grid of GI system duly suspended with 4mm dia GI wire hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures,air conditioning diffuser and ducts ,sprinkler ,smoke detectors etc.The main runners to be secured to structural soffits by hanger @ 1220 mm maximum c/c. the last hanger at the end of each main runner should not be placed at more than 450mm from the adjucent wall,Flush fitting 1220 mm cross tee to be interlocked between main runners @ 610mm c/c,so as to form 600mm x 600 mm grid complete all as specified and as directed.

M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following of treatment/specification from bottom to top:- (i) Taking out old roof treatment and roughening the old concrete slab by picking, sweeping clean and washing down with water to remove dust etc and disposal of rubbish not exceeding 100 mtr distance from starting point. (ii) Screed bed or bedding layer of mortar 15 mm thick in CM 1:4 with mixing of WPC and surface finished fare and smooth without using extra cement after applying a coat of cement slurry @ 3 kg/sqm for laying APP membrane. (iii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.25ltr /Sqm conforming to IS:3384-1986. (iv) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 150 gms/Sqm) shall be applied over bituminous primer as specified above over by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. (v) Applying two coat of aluminium paint over the APP modified membrane @ 0.11Kg/sqm.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

M&L TMT steel bars 10mm dia and over, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L for mild steel TMT bars 5 mm dia and over upto and including 10mm dia cut to length, bent to shape required including cutting, cranking, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia as in stirrups, spacers and binders complete all as specified and as directed.

S&F Rolled mld steel roof trusses ( framed) trussed purlins, crane gantries, rails and fastenings and heavy brackets framing ( Beam, tee, angle, channel or flat section) including distace pieces, cleats etc confirming to Fe 410-W ( Gde E-250 Quality A)complete all as specified & as directed.

S&F rolled mild steel framed works as in doors or gates of angle or other section with gusset plates,, rails, braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides) and hangings also fastening and fixing etcconforming to Fe.290.Gde-E-165.

M&L for mild steel Bands,supports,or stays for rainwater, ventilating pipes, including bolts if required, hooks( stay) , heavy, for large gates, hooks and pintle hinges, large hasp and staples, chains, hand made sliding bolts, clamps, holdfasts, wall ties, hooks for hanging fans, plain angle claets for securing purlins to wood trusses or rafters, knee piece inserts, two way or three way starps, plate washers and similar small articles quality confirming to Fe290-Gde E-165 complete all as specified & as directed.

S&FMild steel framed work such as grills,gratings,etc.with ends of bars shouldered and/or riveted,or forged into spikes,framed guard bars, barred iron doors,ladders, framed balusters, walk ways,railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165.

S&F 1.60mm thick plain mild steel black sheet as in wall cladding, steel gates and similar works, cut to size, holes punched, including round headed screws , clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams including bending or turning up, mitred angles etc complete all as specified & as directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of plain cement concrete (Un-reinforced) in ground floors and paving n exc 15cm thickness (below or above ground level) including removal of spoils/ demolished materials not exceeding 50m and depositing complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in floor finished the surface fair and even without using extra cement complete all as directed.

M&L for 75mm thick PCC 1:2:4 type B-2 (using 40mm graded stone aggregate) as in subase finished to receive floor treatment etc complete all as directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in subase finished to receive floor treatment etc complete all as directed.

M&L for 75 mm thick, PCC 1:3:6, type C2 (using 40 mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide and 30 mm deep at every 2.4 mtrs interval filled with bitumastic compound etc complete all as specified and as direted.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing complete all as specified and directed.

M & L for coloured Non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M&L for 10mm thick Vitrified tiles light shade area of each tile n exc 0.36sqm laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M & L for glazed ceramic coloured tiles 375x250x7mm/300x200x7mm thick, set and jointed in neat cement slurry and pointed in coloured cement as in vertical surfaces such as skirting, dados and risers to steps etc over and including 10 mm thick rendering in cement mortar (1:4) complete all as specified and as directed.

M&L for coloured Non-skid Ceramic tiles 7 to 8 mm thick area of each tile exc. 0.18 sqm but n.exc. 0.38 sqm in floors etc. with and including 15mm thick screed bed in CM 1:4 ,set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as directed.

M&L for coloured Non-skid Ceramic tiles 7 to 8 mm thick area of each tile exc. 0.18 sqm but n.exc. 0.38 sqm in vertical surfaces such as skirting and dado etc. laid over and including 10 mm thick rendering in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as directed.

Demolition of stone slabs and tiles of any description and thickness in floors, approns etc. complete all as specified and directed.

M & L pre-polished cement concrete chequered tiles area of each tiles exc 0.06 Sqm but n exc 0.11 Sqm and 25 mm thick with white cement and pigments of approved make jointed with cement slurry and pointed with white cement mixed with pigment to match with the tiles over and including screed bed of 20 mm thick in cement mortar (1:6) complete all as specified and directed.

M&L for 20mm thick granite ( any type) machine cut ,as in steps, jambs, pillars, window cills, cookong platforms and the like laid over cement screed of 15mm thick in CM 1:4 including pointing in white cement 1:2 using marble dust with admixtures of pigments match the shade of granite stone including rubbing and polishing complete all as specified and as directed.

M&L for 20-25mm thick Kota stone flooring laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

Taking down cement plaster on walls, chajja surfaces, etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for rendering 10 mm thick in CM (1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

M&L for 5mm thick rendering in CM 1:3 on concrete surfaces in ceiling finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:4 on brick/ concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for 15 mm thick rendering in CM 1:6 on brick/ concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for 15mm thick rendering in cement mortar (1:4), in two layers, to fair faces of brick or concrete wall surfaces, top layer 5 mm thick mixed with water proofing compound (@ 2% by weight of cement or as per manufacture's instructions), finished even and smooth without using extra cement complete all as specifed and directed. (Note : Water proofing compound to be measured and paid separately as "Supply only")

Supply only integral water proofing compound complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.

M&L for complete removal of exisring treatment of walls and applying one coat of alkali resistant primer over a coat of white cement putty, sanding the surfaces till smooth finish is obtained and finally applying two coats of cement based paint complete all as specified and as directed.

M&L for complete removal of exisring treatment of walls and applying one coat of alkali resistant primer and applying two coats of oil emulsion distemper complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation of old decorated surface of wall and applying one coat of white wash on wall surface complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and applying three coats of white wash on wall surface complete all as specified and directed.

M&L for preparation of newly plastered surface and applying three coats of white wash on ceiling surfaces complete all as specified and directed.

M & L for preparation of new wood or wood based surface of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paints over a coat of pink primer complete all as specified and as directed.

M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paints over a coat of red oxide, zinc chrome primer complete all as specified and as directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.50sqm in each pane complete all as specified and directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.50sqm in each pane frosted on one side complete all as specified and directed.

Taking up or down 15 mm bore GI tubing from trenches / wall including all fittings segregated, cleaning and stacking the pipe for reuse at site if required complete all as specified and as directed. Note : Excavation and earthwork if any shall be included in the quoted rate

S&F GI tubing15 mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Refixing only old serviceable 15 mm bore Steel tubing and connections as obtained from taking up/down old steel tubing including provision of new fittings in new or old position to walls,ceiling, flooring etc. complete all as specified and as directed.

Taking up or down 20 mm bore GI tubing from trenches / wall including all fittings segregated, cleaning and stacking the pipe for reuse at site if required complete all as specified and as directed. Note : Excavation and earthwork if any shall be included in the quoted rate

S&F GI tubing 20 mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed.

Refixing only old serviceable 20 mm bore Steel tubing and connections as obtained from taking up/down old steel tubing including provision of new fittings in new or old position to walls,ceiling, flooring etc. complete all as specified and as directed.

S&F in repair of 15mm dia Bib taps quarter turn cast copper alloy chromium plated, with crutch or butter fly handles screwed down for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair of 15mm dia Bib taps of PTMT standard any colour screwed for iron pipe complete all as specified and directed.

S&F in repairs, stop valves/ angular stop valve, 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.

S&F in repair 15mm bore pillar taps quarter turn cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair 15mm dia chromum plated Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed etc complete all as specified and as directed.

S&F in repair, 15mm bore dia of concealed stop valves cast copper alloy fancy type chromium plated with long shank and cup complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank 1000 litre capacity of triple layered layer wall construction (Cylindrical, vertical with closed top) hoisted and fixed in position including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule ncluding dismantling of old tank of any description complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank 500 litre capacity of triple layered layer wall construction (Cylindrical, vertical with closed top) hoisted and fixed in position including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule ncluding dismantling of old tank of any description complete all as specified and directed.

S & F in repairs, sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortat to dwarf wall or including fixing cantiliver brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed.

S&F in repair 125 mm dia chromium plated swivel type shower rose with 190 mm long chromium plated shower arm and wall flange suitable for fixing 15 mm bore iron pipecomplete all as specified and directed.

S&F in repair fancy type Brass chromium plated 600mm long Towel Rail fixed with screws and wooden/plastic cleats etc. complete all as specified and directed.

S&F in repair 15 mm dia 450 mm long PVC connection pipe with two PVC PTMT nuts at each ends with rubber washer complete all as specified and directed.

S&F in repair 110 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints and laid in trenches or in floors or fixed to wall as in waste /soil / rain water pipe etc. complete all as specified and directed

S&F 110 mm dia PVC (SWR) bends of any radius complete all as specified and directed

S&F in repair viterous china squatting pan Orissa pattern size 580 x 440mm white with integral foot rest, but excluding flushing cistern but including 'P' or 'S' trap and provision of lime concrete bedding complete all as specified and directed.

S&F in repairs vitreous china wash down water closet (padestal pattern) including connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap set and including white or black seat cover for padestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws etc complete all as specified and as directed.

S&F in repair vitreous china wash basin white flat back size 550 mm x 400mm including all fittings including cutting for and pinning in ends of brackets or erecting stand etc complete (waste coupling 32mm bore CP, 32mm bore PVC waste pipe, cast iron brackets etc shall be deemed to be included in the quoted rate) complete all as specified and directed.

S&Fin repair PVC low level flushing cistern 10 litres capacity with inlet ball valve, float and handles including brackets complete all as specified and directed.

Taking down ceiling/exhaust/wall fan including connection wires carefully, removing to store in safe custody ,painting with synthetic enamel paint by spraying incl. filling cavity and refixing the same in original position after repairing (rewinding if require) including changing the hook ,clamp ,pipe for ceiling fan as per requirement of site complete all as directed

Taking down carefully 50 litre capaciy Geyser ( water heater) including connection removing to store for necessary repairing by replacement of heating element 2 KW, thermostate, apparetus plate etc complete including painting with synthetic enamel paint ( Duco) by using spray painting machine and refixing to its original position with necessary connection and making good disturbed surfaces complete all as directed

Taking down carefully aluminium/ copper point wiring for light/fan/ socket/bell or power point incl. All fittings i.e. switch, sockets, ceiling rose, regulators, batten holders, etc. complete removing materials to store for keeping in safe custody site or handed over to contractor as schedule of credit and making good disturbed surfaces of walls, floors, etc complete all as directed by Engineer-in-Charge.

M&L point wiring with PVC insulated and unsheathed cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts, FRLS grade cable conforming to IS-694 1990 drawn in concealed conduit including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for One light or fan point controlled by one 5 Amps switch one way complete all as specified and directed.

All as per item serial No 128 here-in-before but One 3 pin socket outlet 5 amps on the same board with other switches

All as per item serial No128 here-in-before but One socket outlet 3 pin 5 Amp on independent board.

All as per item serial No 128 here-in-before but with 2.5 Sqmm single core multistranded copper conductor cable for 6 pin 15 Amp socket outlet on independent board and earth continuity wire with 2.5 sqmm cable.

S&F switch piano, flush type single pole one way 5 Amps 230 volt complete all as directed.

S&F socket outlet 3 pin, 2-in-1, 5 Amps flush type complete all as directed.

S&F switch socket combination outlet 5 pin, 2-in-1, 5 Amp flush type complete all as directed.

S&F switch socket combination multipurpose, 2 in 1, 6 pin, 5 & 16 Amp flush type complete all as directed.

S&F ceiling rose surface bakelite 65x50mm three terminal complete all as directed.

S&F lamp holder insulated PVC/ Polycarbonate/ bakelite body, with back plate suitable for batten fitting or PVC round or squre box, complete all as directed

S&F stepped type electronic fan regulator, two module size, flush type complete all as directed.

S&F Environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagonal bulk head black-lit LED10 W -IP-66 luminaire comprising of high brightness LEDs complete all as specified and as directed. Make:- Havells Model HEXAFT10WLED857SSYMBOPC or equivalent Model of make : Philips / Crompton /GE.

S&F in repair LED light fitting of approved make 1X 20 W, 220V, AC decorative box type with driver, holder including LED lamp and connecting up with three core flexible copper conductor cable of suitable size complete all as directed.

S&F in repair LED box type light fitting prewired including LED tube 1X10 W and connecting up with three core flexible copper conductor cable of suitable size complete all as directed. Make : JAGUAR MODEL LGLZO!XOIOXNXLGLZOIXOIPXW or HAVELLS, LUMILINEPLUSBS10WLED865SPCSS or equivalent in PHILIPS/GE/CROMPTON.

S&F in repair LED recess mount downlighter 18W with pressure diecast aluminium heat sink and PC diffuser in white powder coated finish with integrated driver and connecting up with three core flexible copper conductor cable of suitable size complete all as directed. Make: HAVELLS, Model EDGEPRO, Cat No. EDGEPRORDDLR18WLED857S or equivalent in PHILIPS/GE/CROMPTON.

S&F in repair LED light fitting of approved make mirror type with high output diffuser 2 feet, 10 W, 220V, AC decorative type with driver, holder including LED lamp and connecting up with three core flexible copper conductor cable of suitable size complete all as directed.

S&F in repair round shape 12 W , 220V, AC surface type with high efficiency PMMA difuser soft glare free light complete with driver, holder including LED lamp suitable for roof ceiling and connecting up with three core flexible copper conductor cable of suitable size complete all as directed.

S&F in repair LED street light fittings of approved make 35 W 230 V AC outdoor type with high pressure diecast aluminium housing and heat resistant complete with driver, lamp, bracket with impact and corrosion resistant including thermal management in multiple optics complete wit IP 65/66 protectioncomplete all as directed.

S&F in repair regal batten for LED Tube rod pre-wired including LED tube double sided 1x20W connecting up with aluminium housing and sheathed 1100 volt grade flexible copper cable & fix on 2 no. of PVC block complete all as directed. (Make:- Havells, Model-REGALBATTENT8UPTO1X22WDSBSWH+CRSTAL1213T8DSTL20WLED865SGLASS or equivalent model of make Bajaj/ Philips /GE/Crompton)

S&F in repair MCCB DB IP-43 of sheet metal enclosure double door VTPN 4 way with 250 Amps rated copper bus bar 415 volt and grouted in wall with PCC(1:2:4) type B-1 using 20 mm graded stone aggregate.(Make-Legrand cat No-5077 45 or equivalent model in Siemens / Schneider) .

S & F in repair SPN DBs 8 Ways, double door, protection class IP-43 suitable for mounting MCB, DBs conforming to IS-13032, IS-8623, BS-5484 with min 100 Amp rating copper bus bar complete all as specified and as directed. Make :- Legrand Cat No 5076 11 or equivalent model in Siemens / Schneider

S&F in repair MCBs, SP 6 to 32 Amps, 10 KA, 'C' curve IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and as directed. Make :- Legrand Model 4085 90 to 95 orequivalent model in Siemens / Schneider/L&T

S&F in reapir MCBs, SPN 32 Amps, 10 KA, 'C' curve IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and as directed. Make :- Legrand Model 4086 09 to 17 or equivalent model in Siemens / Schneider/L&T

S&F in repair MCB TPN 40 to 63 Amps in accordance with IS/IEC 60898-1, 415 V, 50 Hz,10 kA,C-series rupturing capacity providing in DB complete all as specified. (Make :- Legrand / Siemens/Schnider)

M&L in repair Sub main wiring with 2 runs of 4.0 sqmm, single core, FR-LSH PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20mm dian non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 4.0 sqmm single core FR-LSH PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion complete all as specified and directed. (Note: 2 run of 4 Sqmm cable and 1 run of 4 Sqmm cable along with conduit all together shall be measured as one unit.)

S&F in repair LED building secruity luminaries 48 Watts WSPD epoxy powder coated pressure die cast aluminum housing with wheatherproof gasket for LED's and control gear compartments, pressure die cast aluminium frame with heat resistant toughened clear glass fixed with SS screws LED Specification: CREE LED/Equivalent, Colour temp - 5700 K +/- 300 K Lens,,IP-66,Lumen efficiancy >100 lm/w,surge protection 4kv internal (Built-in) with twin core conductor complete all as directed including testing on completion. (Make: Havells CAT No. ENDURAPEARNEOSL48WLED757SASYTOPC or equivalent of Philips/Wipro/CG)

M&L in repair building secruity light bracket made out of 40 mm bore medium grade GI Pipe with two sets clamps, with nuts and bolts, bend to shape for fixing street light luminaries all as directed, length of GI Pipe shall not be less than 2.0 mtrs complete all as specified and directed.

Supply, laying and testing of XLPE insulated, PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 16 sqmm 4 core laid in trenches / floor or fixed on wall /pole with brass compression cable glands, terminal lugs etc, including taking out/ down the existing old cable complete all as specified and as directed.

Supply and lay GI tubing 25mm bore light grade for cable protection and fixing to the existing pole with flat iron clamp 25x 3mm including nut bolts complete all as specified and as directed.

Supply and spreading fine dry river sand for cushing to UG cable including spreading levelling and hand punning etc complete all as specified and directed.

M&L for sub class 'B' old size bricks laid in trenches for cable protection laid flat width wise along the length of cable complete all as specified and directed.

S&F of Exhaust fans AC single phase 230/ 240 V ,50 Hz metallic heavy body of size 300 mm sweep, 900 RPM with louver fixing with 4 no hold fastener nut and bolt with washer and connecting with flexiable PVC insulated multistranded copper conductor cable of size 1.5 sqmm including civil work opening on wall and making good surface complete all as specified and directed. (Make-USHA, Model-300MM S.PH TURBO HDEF 900 RPM or equivalent model of make Havells/Bajaj /Crompton)

Earthing complete with GI earth plate electrode of size 60cm x 60cm x 6mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level sorrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt fliing in alternate layers etc and connected to and including galvanised earth lead wire 4 mm upto 7.5 mtr by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 20 mm dia GI pipe connected to main control board and GI pipe medium grade 40 mm bore for watering and including funnel, wire mesh, charcoal salt etc RCC pit cover flush to earth pit 50mm thick reinforced with 8mm TMT bar 100mmC/C and PCC chamber pit with PCC (1:3:6) type C1 (using 20mm graded aggregate) including earthwork disposal of surplus soil to distance not exceeding 50 metre) and testing after completion all as specified and shown on plate No 3 of SSR Part-I 2009 with and including demolition of old earthing..

M/S MANOJ PAUL