PROVN OF ADDN TOILET WITH BATH IN CERTAIN SMQS AT AF STN JAIPUR

Amount

Excavation in trenches. exc 1.5m wide and n exc 1.5m depth for foundation etc or for shaft wells, cesspits, manhole, pier etc n exc 1.5 m in depth and getting out in soft/disintegrated rock.

M&L for PCC 1:4:8 type D-2, using 40 mm graded stone aggregate as in foundation and mass concrete.

M&L for TMT bar 10 mm dia and over cuto to length, bent to shape required including cranking bending spirally for hooping for columns, hooking ends and bing with and including mild steel wire (annealed) not less than 0.9 mm dia or secring with clips complete all as specified and directed.

All as per item No 3 here-in-before but 5 mm dia and over up to and including 10 mm dia in stirrups spaces and binders.

M&L for use and waste of form work, for sides of footings, columns bases, rafts and plinth beams complete for a rough finished surfaces all as specified.

M&L use and waste of form work to to sides of pillars posts, struts, piers, columns and stainchions, rough finished, complete all as specified

M&L use and waste of form work to sides and soffits floor and roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams etc complete all as specified and directed.

M&L for use and waste of form work, for to soffits of suspended slabs such ar roof slab, floor slab, landings and similar work not exceeding 200 mm thick complete all as specified andirected.

M&L for reinforcement cement concret, type A-1, 1:1.5:3 (M-20), (Nominal Mix) using 20 mm graded stone aggregate as in footing of columns, plinth beams, bases of columns etc complete all as specified.

M&L for reinforcement cement concrete type A-1, 1:1.5:3 (M-20), (Nominal Mix) using 20 mm graded stone aggregate as in columns complete all as specified and directed.

M&L for reinforcement cement concrete type A-1, 1:1.5:3 (M-20), (Nominal Mix) using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintel over 1.5 m span complete all as specified and directed.

M&L for reinforcement cement concrete type A-1, 1:1.5:3 (M-20), (Nominal Mix) using 20 mm graded stone aggregate as in slabs supported on walls, beams and column in floors, roofs, landings, balconries, canopies, deck slab and slabs and in shelves and the like complete all as specified and directed.

Material and labour for Brick work with sub class 'B' bricks, Straight or curved on plan exc. 6 m mean radius built in CM 1:6, complete all as specified and directed.

Returning filling in including spreading, leveling, watering and well ramming in layers not exceeding 25 cm.

Removing excavated material to a distance exc 250 m and n.exc 500 m complete all as specified and directed.

M&L for for DPC, 75 mm thick in cement concrete type B-0, 1:2:4, 12.5 mm graded stone aggregate including necessary form work complete all as specified and directed.

M&L for cutting opening through old stone masonry walls, built in cement mortar for door, window and other opening, etc or cutting out defective masonry for underpinning including providing fixing and removing shoring, cleaning and stacking stone and removing surpulus to store and rubbihs off the premisses complete all as specified and directed.

M&L forming jambs etc to opening (to foregoing item) with stone including cutting, toothings and properly bonding into old work, including facing and pointing (if necessary) to match existing work in cement mortar 1:4 complete all as specified and directed.

M&L for cutting into old stone masonry, built in cement mortar to form toothings for and bonding new brick or stone work including making good in cement mortar complete all as specified and directed.

Taking down cement plaster on bricks or stone walls etc., including raking out joints, hacking for key scrubing down with water etc, all as directed.

M&L for rendering 15 mm thick on fair faces of brick or stone masonary in CM (1:4) finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick or stone masonary in CM (1:6) finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10 mm thick on fair faces of brick or concrete surface of ceiling in CM 1:3 finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying 2 mm thick water proofing wall care putty and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gms/litre and UV resistance as per IS 15489:2004, alkaly & fungal registance, dirt resistance exteriour paint of required shade (company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm over new surfaces complete all as specified and directed.

M & L for preparation of newly plastered previously untreated surfaces of walls and applying two coats of distemper oil emulsion over and including a coat of average 2 mm thick wall care putty and one coat of primer complete all as specified and directed.

M & L for preparation of new undecorated surfaces of ceiling and applying two coat of Oil Bound Distemper over a coat of primer and 2 mm thick wall care putty, all as specified and directed.

M&L for providing, 40 mm thick (average) plain cement concret, type- B0, 1:2:4 (using 12.5 mm graded stone aggregate as in roof pading, concrete finish even and smooth with using extra cement and using liequied WPC as directed by Engr-in-Charge complete all as specified and directed.

S & F APP based polymeric water proofing membrane of weight not less than 3kg/sqm over a coat of bitumen 85/25 @ 1.20 Kg/sqm over a coat of bituminous primer @0.30lit/sqm complete all as specified and directed.

Supply only liquid water proofing compound.

M & L for Non skid ceramic coloured tiles, joint free, 7 to 8 mm thick (Square or Rectangular) area of each tile exc.0.11 sqm but not exc 0.18 Sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile with and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M & L for glazed ceramic coloured tiles, joint free, in vertical surfaces 450 x 350 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with over and including rendering 10 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces for backing coat of tiles complete all as specified and directed.

M&L for 20 mm thick granite stone slab (table rubbed and polished) as on shelves/cooking plateform over and including like cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

S & F solid PVC door frame of size 50mm x 47mm with a wall thickness of 5mm made out of extruded 5mm thick wood grain printed PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with printed sheet , mitre cut at two corners and joined with two Nos of 150mm long brackets of 15mm x 15mm MS square tube. The two vertical door profiles are to be reinforced with 19mm x 19mm MS square tube of 19 gauge, EPDM rubber gasket and weather seal to be provided through out the frame. The door frame shall be fixed to the wall using 65/100mm long MS screws through the frame using PVC fasteners. Aluminum of four Nos of screws to be provided for each vertical member and miniumum of two nos of screws for each horizontal member complete as per Manufacturer’s specification and drawing and as directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style consisting of frame made out of MS tubes for top & bottom rails.MS frame shall be covered with heat moulded wood grain printed PVC sheet used instead of Plain colour PVC sheet & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900) used instead of exposed portion of PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing as mentioned on Page 149 of SSR-2020 Part-II, complete.

S&F powder coated aluminium (minimum thicknessof powder coating 50 micron) frame work for windows & ventilators, fixed/openable (Top hung/side hung) including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (fittings shall be paid for seperately) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS-733 and IS-1285, fixing with dash fasterners of required dia and size including necessary filling up the gaps at junction i.e at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/peneling, CP brass/stainless screws all complete as per architectural drawings and the direction of Engineer-in-Charge.

S&F anodized aluminium grill (anodized transparent or dyed to required shade accoring to IS : 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing windows frame with CP brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening szie for fixing and operation of handles and fixing approved anodized aluminium standard section around the opening, complete all as specified and directed.

S&F for 4.8 mm thick sheet glass, ordinary quality, exc 0.50 Sqm in each pane, glazing with beads fixed with metal panel pins complete all as specified and directed.

S&F stainless steel wire cloth 0.56 nominal dia of wire and average width of aperture 1.18mm and fixed with tinned teaks galvanised wire staples fixed all as specified

S&F 100 mm size type B-21 Mild steel butt hinges fixed complete all as specified and directed.

S&F Aluminium anodised handles each 125 mm long complete.

S&F Aluminium anodised barrel tower bolt 125 mm size complete.

S&F aluminium sliding door bolts, size 250 mm plate type, with bright bolt not less than 12mm dia with and including a minimum of 6 bolt and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S & F vitreous china wash basin white, flat back or angle back type, size 630 X 450 mm but including waste pipe, brackets, cutting for and pinning in as required complete all as specified and directed.

S & F vitreous china perimium /Ist quality wash down water closet of any colour (closed pattern incuding all necessary accessories like rag bolts/gel gasket, trap etc, (excluding flushing cistern & flush pipe) wall hung type with PVC seat cover and making connection to flushing cistern, including 100mm dia trap etc. complete all as specified and directed.

S&F repair mixer Pillar taps 15 mm bore fancy type, swan neck, long body, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S&F 15mm long body bib taps fancy type cast copper alloy CP with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F 15 mm concealed CP stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repair

S&F 15 mm two-way bore bib taps chromium plated cast copper alloy with crtutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F Brass CP wall mixer three way for mixing hot & cold water screwed down for iron pipe including provision for head and hand shower including and fixed complete all as directed

S & F tubular towel rail, brass chromium plated, 20 mm dia, 'D' type, 60 cm long between flange complete all as specified and directed.

S & F 32 mm cromium plated cast copper alloy waste coupling (half or full threaded) Minimum weight 32mm-45gms/40mm-60 gms) for wash hand basin all complete ad as directed

S&F health faucet (ABS Body) cast copper alloy chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible SS tube and ABS wall hooks including making connections and fixed in position complete in all respect as specified and directed.

S & F Brass chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to 15 mm dia steel pipe or union all complete as directed

S & F stainless steel Soap dish, approximate size 160x 160x90mm any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed by Engr-in-Charge

S&F grating 100 mm dia stainless steel (Min Wt 25 gms) complete all as specified and as directed.

S&F stainless steel toilet paper holder with flat recessed type, fixed to wall with brass screws complete all as specified and directed.

S&F PVC connection pipe 15mm size with PTMT nuts of length 450 mm etc all as specified.

S&F PVC connection pipe 15mm size with PTMT nuts of length 600 mm etc all as specified.

M&L PVC low level flushing cistern 10 Ltr capacity white complete with inlet ball valve float , syphon assembly and dual flush button and brackets including flush PVC flush pipe 32 mm dia complete all as specified and directed.

S & F PVC single door bathroom cabinet contains 4 shelve with 5 mm thick mirror- any colour and size of 25.40 x 10.20 x 35.6 cm dimension complete all as specified and as directed by Engr-in-Charge.

S & F of 15 mm bore steel water tubing medium grade galvanised with and including all fittings and fixed to walls and ceilings or laid under floors complete all as specified and directed.

S & F of 20 mm bore steel water tubing medium grade galvanised with and including all fittings and fixed to walls and ceilings or laid under floors complete all as specified and directed.

S&F Cast iron floor trap 75 mm , with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F Cast iron soil, waste and vent spun pipes 75mm , in any length with or without ears with cement joints, laid in trenches or in floors all as directed and specified.

S&F Cast iron soil, waste and vent spun pipes 100mm , in any length with or without ears with cement joints, laid in trenches or in floors all as specified and directed.

S&F cast iron soil, waste and vent spun pipes 100 mm bore in any length with or without ears with cement joints fixed to walls all as specified and directed.

S&F spun cast iron 100mm bore bends etc all as specified

S&F spun cast iron 75mm bore bends etc all as specified

S&F 500 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) triple layer white in colour hoisted and fixed with 20 mm dia PTMT float valve with complete accessories complete all as specified and directed.

S & F 20 mm bore size Stop valves, cast copper alloy chromium plated screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

M&L for 75 mm thick plain cement concrete type C-2, 1:3:6, using 40 mm graded stone aggregate as in plinth protection or similar work, concrete finish even and smooth with using extra cement complete all as specified and directed.

M&L for 75 mm thick plain cement concrete type C-2, 1:3:6, using 40 mm graded stone aggregate for sub base complete all as specified and directed.

M&L for chequered cement concrete tiles glossy finish 30cmx30cmx25 mm thick, with coloured cement and pigment, set, jointed and pointed in neat cement slurry in floors over and including 15 mm thick screed bed in CM 1:6 all as specified and directed.

S & F 150 mm bore, Reinforced concrete pipes, class NP-2, laid and jointed with cement mortar (1:2) with jute and rubber ring complete with collars, complete all as specified and as directed.

M&L cement concrete 1:3:6 type D2 using 40 mm graded stone aggregate as in bed to drain pipes of 150 mm bore including packing under and haunching against the sides of pipes after they are laid and tested as specified.

M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds,/ stopped ends etc complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drain of 150 mm dia and over, making good to pipes and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B-1, smooth finished, and reforming benching as required, complete all as specified and as directed.

M&L for reinforcement cement concrete (nominal mix), type B-1, 1:2:4 (20 mm graded stone aggregate) as in man hole cover complete all as specified and directed.

M&L for point wiring with PVC insulated multi stranded cable with copper conductor of size 1.5 Sq mm single core 1100 volts grade ISI mark drawn through and including PVC conduit including necessary accessories like bends, tees, elbow, etc fixed on wall/ceiling including modular type sunken type MS box of suitable size, modular white cover plate, including 1.5 Sq mm PVC insulated copper conductor earth continuity wire for (a) One Light/fan point controlled by one way switch.

(b) One three pin 5 Amp socket on same board with other switches.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

S&F Modular switch 1 way 6A, 1 module complete all as spd and directed.

S&F Ceiling rose, 3 phase/PVC/ polycarbonate, isolated body complete all as spd and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as spd and directed.

S&F Modular Socket 3 pin 5 Amps complete all as spd and directed.

M/S AAYUSH ENGINEERING&COMPANY (BID ID -3485661)