Construction of a Double Occupancy Sharing Girls Hostel 2nd 65 Rooms G plus 7 for Nursing and Paramedical Students at AIIMS,Raebareli

Civil Work

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge. All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m. including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m.

Pipes, cables etc. not exceeding 80mm dia.

Pipes, cables etc. exceeding 80mm dia. But not exceeding 300 mm dia.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift.

Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Surface dressing of the ground including removing vegetation and in- equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion@ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement: 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.G. 20% with 1% concentration

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from natural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases for columns

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources).

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas,lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum

All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform

Shelves (Cast in situ)

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landings, beams and balconies (Plan area to be measured)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6(1 cement :6 coarse sand)

Extra for providing and placing in position 2 Nos 6 mm dia. M.S. bars at every third course of half brick masonry.

Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement: 4 coarse sand)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red Area of slab upto 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3(1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Vitrified tiles in diferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Float glass panes 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).

Extra for providing frosted glass panes 4 mm thick (weight not less than 10 kg per sqm) instead of ordinary float glass panes 4 mm thick (weight not less than 10 kg per sqm) in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISi marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISi marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378) 250x16 mm

Providing and fixing ISi marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378) 150x10 mm

Providing and fixing chromium plated brass handles with necessary screws etc. complete: 125 mm

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing ISi marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 100x75x4 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 250x10 mm

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer- in-charge. With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing Brass 100 mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing and fixing chromium plated brass casement stays (straight peg type) with necessary screws etc. complete : 300 mm weighing not less than 330 gms

Providing and fixing chromium plated brass casement window fastener with necessary screws etc. complete.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thick

Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately).

Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.l.sheet (zinc coating not less than 120 gm/sqm) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge (panneling to be paid for separately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/sqm) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/ powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 60 minutes of fire resistance both integrity & radiation control (EW60) and minimum 20 minutes of insulation (El20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & El. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/ structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540-F & ISO 11600 Upto 5 mm depth and 5 mm width

4 mm thick ACP

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, bufing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 40 mm wide and 4 mm thick

Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : Medium shade pigment using 50% white cement, 50% ordinary cement

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8 mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20 mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, difusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross 'T' of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form grid of 1200x600 mm and secondary cross 'T' of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8 mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2 mm thick flat

Providing & fixing at all heights, levels and locations colour finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately). 0.56 mm Aluminium Colour profile with center to center pitch of 175 mm, depth of 46 mm, top crest width of 41 mm, bottom valley width of 80 mm, overall profile width of 1144 mm, cover width 1050 mm.

12 mm cement plaster of mix: 1:4 (1 cement: 4 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand)

6 mm cement plaster of mix: 1:3 (1 cement :3 fine sand)

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Neat cement punning.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour: New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats

Finishing walls with Acrylic Smooth exterior paint of required shade: New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. “All above operations to be done in order and as directed and specified by the Engineer-in-Charge”: With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge.

ROAD WORK

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth lead upto 50 metres.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25

Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineerin- charge.

Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer- in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately) Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately. Cement concrete prepared with batch mixing machine

Providing and laying 75 mm thick compacted bed of dry brick aggregate of 40 mm thick nominal size including spreading, well ramming, consolidating and grouting with jamuna sand, including finishing smooth etc. complete as per direction of Engineer-in-charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer- in-charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-in-charge.(Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). Overhead informatory road signage

Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.)

HORTICULTURE WORK

Trenching in ordinary soil upto a depth of 60cm including removal and stacking of serviceable materials and then disposing surplus soil, by spreading and neatly levelling with in a lead of 50m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking sludge at site including royalty and carriage upto 5 km range (sludge measured in stacks will be reduced by 8% for payment).

Supplying and stacking at site dump manure from approved source, including carriage complete (manure measured in stacks will be reduced by 8% for payment). Screened through sieve of I.S. designation 16 mm

Rough dressing the trenched ground including breaking clods & Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.

Fine dressing the ground

Supplying and stacking at site. Good earth

Spreading of sludge, dump manure or/and good earth in required thickness including mixing earth and sludge or manure in the required proportion specified or directed by the Officer in Charge (Cost of sludge, dump manure or/ and good earth to be paid separately).

Spreading of sludge, dump manure or/and good earth in required thickness including mixing earth and sludge or manure in the required proportion specified or directed by the Officer in Charge (Cost of sludge, dump manure or/ and good earth to be paid separately).

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately):

Holes 1.2 m dia and 1.2 m deep.

Holes 60 cm dia, and 60 cm deep.

Providing and Displaying Marigold jaffri dwarf in different colour well developed with fresh & healthy foliage with 12 to 15 flowers in full bloom specimen plant 23 to 30 cm ht. in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and stacking of Bottle palm of ht. 270-300 cm bottom girth 40-50 cm well developed in big HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Ficus religiosa (Peepal) of height 150-165 cm. in big poly bags of size 30 cm as per direction of the officer-in-charge.

Providing and stacking of Eugenia jambolana (Jamun) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Murraya Koenigii spreng (Kadipatta/meetha neem) of ht 45-60 cm well developed in earthen pots of size 20 cm. per direction of the officer-in-charge.

OTHER MISCELLANEOUS CIVIL ITEMS

Providing and fixing of S.S. letters with ACP Sheet at back.

Supply, installation, testing and fixing of stainless steel (SS-304) signage board of approx. 8 feet overall height, comprising a 2’ × 3’ stainless steel plate duly covered with radium sheet on both sides, complete in all respects including all necessary fittings, accessories, transportation, loading, unloading and installation at site as per direction of Engineer-in-Charge.

Supply, Installation & fixing of Vinyl Print with ACP, complete as per design and site requirements.

Supplying and fixing min. 18 mm thick smooth finish black granite inauguration stone of superior quality with overall size of 1500X900mm with ornamental edge moulded granite / marble / cement plaster band of approved shape. The prepared block shall be fixed with cement mortar 1:3 (1 Cement: 3 Coarse sand) in brick wall/block work with tiles/stone after chased, including finishing and painting all-round the stone and making aesthetically beautiful. The inauguration stone should contain engraved letters with chemically printing /stainless steel of approved matter in Hindi & English of required colour and size etc. and provision of curtain raising/sliding, light and landscaping/area development all around, complete as approved by CLIENT

Providing and fixing 150 mm wide, 22 gauge and 18mm square chicken wiremesh at junctions of concrete and brick work and other locations at all heights placed symmetrically on the joint, including cutting to required size, fixing in position with cement and nails etc complete in all respects as per specifications/drawings and to the entire satisfaction of the Engineer in Charge.

Proving and fixing glass Reinforced Concrete (G.R.C) Screens in approved size, pattern design, thickness and color of approved make .The Screen should be made from White Portland cement ,Quartz, Fine Silica Sand, Alkali Resistant Glass Fibre Super Plasticizer Polymer and U.V resistant Synthetic inorganic pigment for pigmentation. The material casting should take place in Synthetic Rubber /FRP moulds of approved make & shape. The fixing of screens to be done with Stainless Steel (SS-304) ‘L’ shaped Clamps, dash fasteners and pins, as required at site.

Technical specification of GRC Screens. Internal member thickness 30 mm and border thickness 50 mm Dry Density: 1800 kg/m3 (min) Water absorption: Less than 6% of dry weight by immersion over a period of 24 hours. Compressive strength: (M-40 Grade) Wet Transverse Strength: 7 N/mm (min) Abrasion Resistance: Less than 2.0 for E.H.D Thermal Conductivity: 1.63 W/MK at 3% moisture content : 1.80W/MK at 5% moisture content

FIRE FIGHTING WORK

(A) Supplying, Installation, Testing & Commissioning of Electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required:(Terrace Pump)

(B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal confirming to IS 1520.

(C) Suitable HP Squirrel cage indution motor, TEFC type suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, confirming to IS-325.

(D) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.

(E) Suitable cement concrete foundation duly plastered with anti vibration pads.

900 lpm at 35 m head

Providing, laying, testing & Commissioning of 'C' class heavy duty MS pipe confirming to IS 3589/IS1239 inculding welding, fittings like elbows,tees, langes,tapers,nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of syntetic enamel paint of required shade complete as required:

25 mm dia

80 mm dia

100 mm dia

150 mm dia

Providing, laying, testing & commissioning of 'B' class medium duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100 mm dia

Supplying & fixing single headed internal yard hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel, ISI marked, confirming to IS 5290(type A) with blank Gunmetal/Stainless Steel cap and chain as required: Single headed Gunmetal

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :

100mm dia

150mm dia

Supplying & fixing orifice plate made out of 6 mm thick stainless steel(grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required:

Providing, installation, testing and commission of non-return valve of following sizes confirming to IS: 5312 complete with rubber gaskets GI bolts, nuts, washers etc as required:

80mm dia

100 mm dia

150mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 150mm dia

Supplying & fixing 63 mm dia, 15m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. confirming to IS 636(type-A) as required: Gun Metal

Supplying & fixing First-aid hose Reel with MS construction spray painted in post office red,conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type-2 as per IS:12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipments on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle confirming to IS:903 suitable for instantaneous connection to interconnect hos pipe coupling as required. Gun Metal

Supplying & fixing air vessel made out of 250 mm dia,8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required.

Providing & fixing of pressure switch in M.S. pipe line including connection etc as required.

FIRE DETECTION & ALARM SYSTEM

Supplying, installation, testing & commissioning of heat detector operating at 54/57 degree centregrate with rate of rise cum fixed temperature(dual thermistor) type with mounting base complete with all connection etc. as required.

Supplying, installation, testing & commissioning of smoke detector operating with builtin LED and mounting base complete with all connection etc. as required.

Supplying, installation, testing & commissioning of Manual call Boxes of MS constuction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supplying, installation, testing & commissioning responce indicator on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box(16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching trasformer etc. complete as required.

Supplying, installation, testing & commissioning talk back slave station in surface/recess suitable for operation on simplex mode complete with P.T.T. knob & speaker/microphone cenclosed in a M.S. box(16 SWG)/ABS box with break glass in front etc. complete as required.

Supplying & laying of 2X1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS/HFFR outer sheath complete as required.

Supplying & laying 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required.

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilityes as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 4 Zone

Supplying, installation, testing & commissioning of main control and indicating panel made out SWG MS sheet to accommodate the following items duly powder coated in approved colour with louvers for ventilation, locking arrangement, audio and visual indication for fire alarm and public address system, monitoring system including connections, interconnections etc complete as required.

10 Zone panel for fire alarm system

250 Watt amplifier racks suitable for operation on 230V AC/24VDC supply confirming to IEC-268-3 complete with all accessories as required-2 Nos.(one to act as standby)

Talk back master station with LED PTT(press to talk) push button for operation on 230V AC/24 V DC supply confirming to IEC-268 for simplex mode of operation/communication suitable for 20 Nos. talk back unit-1 set.

Amplifier change over switch for inter changing amplified-1 No.

Gooseneck microphone with stand and ON/OFF switch-1 No.

Main ON/OFF switch,fuse indication lamps, DC and AC voltmeters & ammeters, terminal blocks etc. complete as required-1 set.

Battery charger trickle cum boost to take complete load of fire alarm & PA system complete with all accessories including providing & fixing of 2 nos.12 volt, 60 AH each sealed maintenance free bateries-1 set.

FIRE FIGHTING SYSTEM (EXTERNAL)

Supplying & fixing single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, confirming to IS 5290(type A) with blank Gunmetal/Stainless Steel cap and chain as required: Single headed Gunmetal

Supplying, fixing, testing & commission of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets confirming to IS 13095 of following sizes as required:

80 mm dia

100 mm dia

Supplying & fixing of Fire brigade connection of cast iron body with gun metal male instantaneous inlet coupling complete with cap and chain as required. for suitable dia MS pipe connection conforming to IS 904 as required:

2 way-100 mm dia M.S. Pipe

4 way-150 mm dia M.S. Pipe

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.

100mm dia

150mm dia

OTHER MISCELLANEOUS FIRE ITEMS

Supply & fixing of fire extinguisher, ABC Type 6.00 kg. capacity(ISI Marked IS:15683 & TAC approved) comlete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

Supply & fixing of CO2 type fire extinguisher, 4.5 kg. capacity(ISI Marked IS:2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.

Providing/Fixing of Fire Hose cabinet box made out of 18 gauge MS sheet including two coats of post office red paint over one coat of primer with 4 mm, thick glass door in front painted “FIRE” in red luminous paint. The size of the box should be 750 mm X 600 mm X 250 mm size capable of accommodating a pair of hose with coupling and nozzle. The box should be floor mounted type with railway coach lock arrangement and lever for opening the door after breaking the glass complete. Make : Standard/Lifeguard or equivalent.

Providing & Fixing of 1.6 mm thick M.S / Door Frame, Door capable of accommodating fire Hose Reel, Landing Valve, Hose Pipes, fittings & accessories. The door shall have a front glass with lock and key arrangement & shall be painted with post office red colour (approval shall be taken on the basis of submitted sample before ordering).(Liasioing with civil contractor for making Recessed type mansoary box (by civil contractor).

Supplying and fixing of Self Glow Exit signage for stairs and exits made out from not less than 4 mm of transparent acrylic sheet of 300 x 150 mm size with self illuminated plastic words of 100 mm height suspended from ceiling by means of M.S. chain or fixed of the walls as required and as directed at site..(MAKE : Agni Suraksha (ASES) / Securiton-aka /System Sensor or equivalent)

Supplying and fixing in position the following type of sign board made out of 3 mm thick"Opaque" PVC foam board with computer cut, PVC non-reflective self adhesive vinyl painted foam board, complete with mirror fasteners.

Signage with the following text"IN CASE OF FIRE, USE STAIRS UNLESS INSTRUCTED OTERWISE" of 1.25 cm height letters in red with white back ground. The size of the board shall be 25 cmx30 cm and shall be fixed at the height of 2 mtrs. From finished floor near manual call points.

Floor identification signage(ie, GROUND FLOOR, etc) at the each stair & LIft enclosure on every floor, indicating the floor number in words, lettering size shall be 7.5 cm with contrasting colour from back ground shall be 15 cmx60 cm.

Supplying and fixing in position of Fire Escape Route Plan A2 size.

Supplying and fixing of Fire man axe. Make :- Agni Suraksha (ASES) or equivalent

Supply, Installation, Testing and Commissioning of electronic siren with suitable audible range of 1 k.m. approximately 4 watt.complete in all respects. Make :- Agni Suraksha (ASES) or equivalent.

Supplying and installing at approved location approved make Fire Buckets of 24 gauge galvanized steel sheet, standard of round bottom shape, painted white inside and red outside and black on the bottom, inscribed with letter "FIRE" in black and gold. Cost shall be inclusive of providing MS stand duly painted over a coat of primer (one stand shall be suitable for hanging 5 buckets without Canopy).

Providing & fixing Puddle Flanged including 60 to 90 cm long Gl pipe piece welded / threaded with MS plates 450x450x6mm thick with both end screwed / flanged For 100 mm dia pipe

PLUMBING & SANITARY ITEMS (INTERNAL)

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white plastic seat and lid

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litre with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink without drain board 610x460 mm bowl depth 200 mm

Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete. Semi rigid pipe

a) 32mm dia

b) 40mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 50 to 80 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

15 mm nominal bore

20 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing Toilet paper holder a) C.P. brass

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion . (i) Single socketed pipes.

75mm diameter

110mm diameter

Providing and fixing on wall face unplasticised PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion.

Bend 87.5 degree

75mm Bend

110 mm Bend

Shoe (Plain)

110 mm Shoe

Coupler

Coupler 75 mm

Coupler 100mm

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110mm

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and laying cement concrete 1:5:10(1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size) around P.V.C /C.I. Soil and waste pipe including bed concrete as per standard design(embedded in the flooring / ground) 110/90 mm diameter

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. internal work -Exposed on wall

15mm dia nominal outer dia pipes

20mm dia nominal outer dia pipes

25mm dia nominal outer dia pipes

32mm dia nominal outer dia pipes

40mm dia nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc.

15mm dia nominal outer dia pipes

20mm dia nominal outer dia pipes

25mm dia nominal outer dia pipes

Providing & fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing gate valve (with cap complete with bolts, nuts, rubber insertion etc.

25mm dia nominal bore

32mm dia nominal bore

40mm dia nominal bore

50mm dia nominal bore

80 mm nominal bore

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4(1 cement: 2 couarse sand: 4 graded stone aggregate 20 mm nomonal size), including finishing complete so as to make it leak proof.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.

40 mm nominal bore, 206 mm long, weighing not less than 690 gms

50 mm nominal bore, 242 mm long, weighing not less than 1240 gms

Providing and laying Non pressure NP2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand ) including testing of joints etc. complete.

150mm dia. R.C.C. pipe

250mm dia. R.C.C. pipe

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) upto the haunches of S.W./R.C.C. pipes including bed concrete as per standard design

150mm diameter

250mm diameter

Providing and fixing square mouth S.W. Gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 Kg and frame to be not less than 2.70 Kg as per standard design: 150 x 100 mm. size P type With Sewer bricks conforming to IS : 4885

Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg).With FPS bricks of class designation 75 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth of man hole size 90x80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement:3 coarse sand :6graded stone aggregate 20 mm nominal size) as per standard design With 20x20 mm square bar

Supplying, fixing, testing and commissioning of following sizes Motorized Butter fly Valve with CI Body, SS Disc, O - ring and minimum PN-16 pressure rating , conforming to BS 5155, IS 13095, with IP-55 actuator, capable of accepting upto 10V DC , and upto 20mA electric signal and providing similar transduced feedback output to control system as required. 50 mm dia

Providing and fixing CP finish 300 mm Bottle Trap of approved quality & make and as per the direction of Enginer-in-charge.Make- Cera or equivalent

Providing and fixing C.P. shower with arm Make- Cera or equivalent

Providing and fixing 45 cm long unplasticised Heavy duty PVC connection pipe with brass unions. 45 cm length

Providing & fixing CP bib cock 15 mm of approved quality conforming to IS 8931 Make Cera or equivalent.

Providing & fixing C.P. long body bib cock 15 mm of approved quality conforming to IS standards and weighing not less than 690 gms. Make Cera or equivalent.

Providing & fixing C.P. Wall mixer with provision for overhead shower of approved quality conforming to IS standards and weighing not less than 690 gms. Make Cera or equivalent.

Providing & fixing C.P. two way bib cock 15 mm of approved quality conforming to IS standards and weighing not less than 690 gms. Make Cera or equivalent.

Providing & fixing Centre hole basin mixture of approved quality conforming to IS standards and weighing not less than 690 gms. Make Cera or equivalent.

Providing & fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 Make Cera or equivalent.

Providing & Fixing of CPVC Ball Valve with brass threated

Supply and fixing of UPVC S.W.R. pipe confirming to IS-13592 including jointing the pipes with rubber ring,lubricant and UPVC SWR coupler confirming to IS-14735. Also including excavation of trenches cutting of walls and holes and repairing the walls,floors and refilling the trenches as before with supply and cost of other fittings such as elbow,bend,tee and y-tee,Cowel including supply of all marerial labour and T&P. Required for proper completion of work.

Supply and fixing of UPVC S.W.R. pipe nahni trap size 100x75,110/90 mm confirming to IS-14735 self cleaning design fixed in PCC 1:2:4 and supply and fixing of 125 mm dia heavy duty CP brass jali.

Providing & Fixing of Table Top wash basin 600x400 mm of white colour Make - Cera or equivalent.

Providing & Fixing C.P. Brass Health Faucet -Make-Cera or equivalent

Providing & Fixing C.P. Soap Tray -Make-Cera or equivalent

Providing & Fixing Liquid Soap dispenser Make - Cera or equivalent

Providing and fixing C.P. stop cock with wall flange 15 mm of approved quality. Make - Cera or equivalent

Providing & Fixing C.P. towel rail with all complete fitting as per approved make as approved by Engineer-in-charge. Make - Cera or equivalent

Providing and fixing rob hook with all complete fitting as per approved make as approved by Engineer-in-charge. Make - Cera or equivalent

Providing and fixing Optimum Hand Dryer. Material : AISI 304 Stainless Steel Finish : Satin with all fitting, nuts, bolts etc. complete

Supply and Installation of wall mounted Grab Bar 600 mm long Make-Cera or equivalent

Supply and Installation of SS drain jali 125 mm

Providing and fixing standard MS hot dip G.I. flanges 700 mm long heavy class GI pipe (IS:1239), screwed or welded complete with EPDM gasket, nuts, bolts and washers etc. complete including testing of joints. etc., complete. The flanges shall be as per I.S:6392.

50mm dia nominal bore

80mm dia nominal bore

100mm dia nominal bore

Supply installation, testing and commissioning of water Cooler 80 Ltr capacity of approved quality conforming to IS standards. Make-Blue Star, Voltas or equivalent.

Supply installation, testing and commissioning of RO Purifier 100 LPH of approved quality conforming to IS standards.

Supply installation, testing and commissioning of Solar Water heater of approved quality conforming to IS standards.

Supply installation, testing and commissioning of water Geyser of approved quality conforming to IS standards.Make- Crompton or equivalent. Geyser capacity 25 L.

Supply installation, testing and commission Pressure Pump 2HP of approved quality conforming to IS standards.Make- Kirloskar or equivalent.

Supply, Installation, testing & commissioning of (Horizontal / Vertical inline single/multistage centrifugal pumping set) with mechanical seal, C.I. suction & discharge. SS 304 impeller, SS-304 stage casing & SS-316 shaft connected to a TEFC induction motor with IE2 efficiency class of suitable HP for 415 volts, 3 phase, 50 cycles A.C. supply including electrical panel .Make- Kirloskar or equivalent Domestic Water Supply pumps : Pump Capacity 10m3/h.(Each Pump) at 70m head (1 Working + 1 Stand-by)

EXTERNAL PLUMBING WORK

Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design Inside size 90x120 cm & 90 cm deep including C.I. cover with frame (medium duty) total wt. of cover & frame to be not less than 116 Kg (wt. of cover 58 Kg & wt. of frame 58 Kg. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes : Extra for depth of man hole size 90x120 cm

Providing orange colour safety foot rest of minimum 6mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS: 1786 having minimum cross section as 23 mm x25mm and over all minimum length 263mm and width as 165mm with minimum 112mm space between protruded legs having 2mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufactures's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) complete as per design.

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) cement plastered on both sides with cement mortar ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 100 to 250mm diameter

Providing and fixing gun metal non return valve of approved quality (screwed end) 80 mm nominal bore Vertical

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work

50 mm nominal dia Pipes

65 mm nominal dia Pipes

80 mm nominal dia Pipes

Constructing masonry Chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement :4 coarse sand ) for sluice valve, with C.I. surface box 100mm top diameter, 160mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design : With F.P.S. bricks

RAIN WATER HARVESTING WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size).

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. M.D. -10- Circular shape 500mm internal diameter

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-incharge, upto 90 metre depth below ground level. Drilling of 300mm dia bore hole manually.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/medium/coarse, in required grading & size as per actual requirement, all complete as per direction of Engineer-in-charge.

ELECTRICAL WORK

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq.mm. FRLS/HFFR PVC insulated copper conductor single core cable etc as required.

Group C

Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular type switch, modular plate, suitable G.I. box and earthing the point with 1.5 sq.mm. FRLS/HFFR PVC insulated copper conductor single core cable etc as required.

Wiring for circuit/sub-main wiring along with earth wire with the following size of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2X1.5 sqmm + 1x1.5 sqmm earth wire

2X2.5 sqmm + 1x 2.5 sqmm earth wire

2X4.0 sqmm + 1x 4.0 sqmm earth wire

2X6.0 sqmm + 1x 6.0 sqmm earth wire

4X10 sqmm + 2x 6.0 sqmm earth wire

4X16 sqmm + 2x 6.0 sqmm earth wire

Supplying and drawing following pair 0.5 sqmm FRLS PVC insulated annealed copper conductor, unarmoured telephone cable in the existing surface/recessed steel/PVC conduit as required.

Supplying and drawing co-axial TV cable RG-6 graded, 0.7 mm solid copper conductor PE insulated,shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supply and fixing of following size of PVC conduit alongwith the accessories in recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required:

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required.

5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Telephone socket outlet

TV antenna socket outlet

Bell push

Supply and fixing of two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/modules, GI box along with modular base & cover plate for modular switches in recess etc as required.

1 or 2 module(75mm X 75 mm )

3 Module (100mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

8 Module (125mmX125mm)

12 Module (200mmX150mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.

1 or 2 Module

3 Module

4 Module

6 Module

8 Module

12 Module

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch,connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connection etc. as required.

Supplying and fixing 3 pin 5 A ceiling rose on the existing junction box/wooden block including connectionetc. as required.

Supplying and fixing brass batten/angle holder including connectionetc. as required.

Instalation,testing & commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLSCFL/LED lamps per fitting, complete with all accessories including connection etc. as required.

Installation, testing and commissioning of prewired, flourescent fitting / compact fluorescent/LED fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling / wall, including connection with 1.5 sq. mm. FRLS/HFFR PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. Including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connections, testing, commissioning etc. as required.

upto 450 mm sweep.

Extra for fixing the louvers / shutters complete with frame fro exhaust fans of all sizes.

Providing and fixing circular/Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/M.S. sheet box by means of 3.3 mm dia round headed screwed, one loc at the conrners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

DISTRIBUTION BOARDS, MCB'S & ISOLATORS

Providing & fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in in existing panel board including drilling holes in cubical panel, making connections, Ics=100% Icu and Operational Voltage 690V etc as required.

100 A, 30 KA, FPMCCB

Supplying and fixing following way, Horizontal type three pole and neutral MCB distribution board, 415 volts on surface /recess complete with , tinned copper busbar, neutral busbar, earth bar, din bar, interconnections, powder painted including earthing etc. as required (But without MCB / RCCB / Isolators).

6 way (4 + 18), Double door

8 way (4 + 24), Double door

Supplying and fixing following way, surface/recess mounting,vertical type 415V, TPN MCB distribution board, on steel sheet, dust protected, duly power painted, inclusive of 200 A tinned copper busbar, common neutral link, earth bar, din bar, for mounting MCBs (But without MCBs and incomer) as required(Note:vertical type MCB TPDB is normally used where 3 phase outles are required.)

4 way (4 + 12), Double door

Supplying and fixing 5 amps. to 32 amps. rating, 240 volts `C' series, miniature circuit breaker (MCB) suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single Pole

Supplying and fixing single pole, blanking plate in the existing MCB DB complete etc. as required.

Supply and fixing following rating double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB) having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supply and fixing 20 amp, 240 volts, SPN industrial Type, socket outlet ,With 2 pole and earth ,metal enclosed plug top along with 20 amp. `C` series SPMCB , in sheet steel encosure, on surface or in recess with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Providing and fixing M.V. danger notice plate of 200 mmx150 mm, made of mild steel, at least 2 mm thick, and viterous enameled white on both sides, and with incription in single red colour on front side as required.

Supplying and fixing Cable End Box(Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution borad, 415 Volts, on surface/recess, complete with testing and commissoning ect. as required.

For 6 way, Double Door TPNMCBDB

For 8 way, Double Door TPNMCBDB

Supply and installing of following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, jointed with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

3000mm width x 62.5mm depth x 2.0mm thickness

600mm width x 62.5mm depth x 2.0mm thickness

Earthing with GI earth pipe, 600 mm X 600 mm X 6 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc, with charcoal/cock and salt as required.

Earthing with Copper earth pipe, 600 mm X 600 mm X 3 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc, with charcoal/cock and salt as required.

Supplying and Laying of 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection / terminating with nut, bolt, spring, washer etc. as required.( jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

Supplying and Laying of 25 mm X 3 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection / terminating with nut, bolt, spring, washer etc. as required.( jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing & fixing 25 mm x 5 mm. copper strip on surface or in recess for connection etc. as required.

Providing & fixing 6 SWG dia G.I. on surface or in recess for loop earthing as required.

Supplying, installation, testing & commissioning of Astronomical time switch of following configuration to be mounted in feeder pillars/lighting DBs for automatic switching On & Off of street lights at sunset & sun risr or twillight(Auto On, Auto Off, Auto modes) with manual override facility with 12/24 hour display format with suitable battery and indication for relay status i/c progamming at site complete required.

02 output per phase and suitable for single phase supply

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Upto 35 sq. mm

Above 35 sq. mm and Upto 95 sq. mm.

Above 185 sq. mm and Upto 400 sq. mm.

Laying and fixing of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size on cable tray as required.

Upto 35 sq. mm(clamped with 1 mm thick saddle)

Supplying and making cable route marker with cement concrete 1:2:4(1 cement:2 course sand: 4 grades stone aggregate 20 mm nominal size) of size 60 cm X 60 cm at the bottom and 50 cm X 60 cm at the top with a thickness of 10cm including inscription duly engraved as required.

Supplying & making end termination with brass compression gland and aluminium lugs for the following size of PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

2 X 6 sqmm. (19mm)

2 X 10 sqmm. (19mm)

3.5 X 35 sqmm. (32mm)

3.5 X 300 sqmm. (70mm)

4 X 10 sqmm. (25mm)

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep) and refilling etc as required.

100 mm Dia

150 mm Dia

OTHER MISCELLANEOUS ELECTRICAL ITEMS

Providing and installing DWC HDPE pipe of required diameter including supply of all necessary fittings, excavation of trench, pipe laying, jointing, alignment and backfilling of soil, complete as directed by Engineer-in-Charge. Sand bedding and protective cover shall be excluded.

90 mm dia

160 mm dia

100 KVAR Automatic Power Factor Correction (APFC) Panel

Providing, supplying, installing, testing and commissioning of indoor type, floor mounted, free standing Automatic Power Factor Correction (APFC) Panel of 100 KVAR capacity, suitable for 3-phase, 415 V ±10%, 50 Hz AC system. The panel shall be fabricated from CRCA sheet steel with powder coated finish, IP-42 protection, compartmentalized design with separate incomer and capacitor sections, complete with aluminium bus bars, earthing, ventilation and all accessories, conforming to relevant IS standards and CPWD specifications.

Outgoing (Capacitor) Section Outgoing feeders comprising 525 V, ISI marked, self-healing MPP capacitors arranged in suitable stages with capacitor duty contactors. Each capacitor stage shall be connected in series with 14% detuned reactors for harmonic suppression. Capacitors and reactors shall be mounted on powder coated MS channels with proper ventilation and earthing.

Outgoing (Capacitor)

L.T. PANEL(LOC-STILT FLOOR)

Supply, Installation, Testing and Commissioning of L.T. Panel vermin proof floor mounting, M.S. Channel Base with bottom and Fabricated out of 2.0/1.6 mm thik CRCA sheet steel painted with powder coated paint of shade as per the direction of Engineer In charge after proper sheet treatment peocess of sheet steel. The bus bar of panel shall be electrical grade high conductive alluminium alloy of appropriate cross section as per the rating. The main busbar shall be run throughout the panel of rating as main incomer rating. The Bus Bar shall be supported by non hygroscopic SMC/DMC Bus bar suports which shall be mounted on proper interval to ensure the bear the jerks of suport of short cuircuit of 50kA for panels having ACB as Incomer & 36 kA for panels having MCCB Incomers. Panel shall be constructed in fully Segregated Compartment Design for each Feeder as per 3b construction Format. The panel shall be completed in all respect as per IS 8623 Part 2 & 3. There shall be Seperated metering Component for Incomer metering and Outgoing metering.

All Incomer Feeders shall be provided with Multifunctional metering along with phase Indicating lights and other associated components such as CT control MCB Terminal Blocks etc. and all outgoing Feeders 100 A & above shall be provided with 3 phase Ammeter along with phase Indicating lights and other associates components such as CT control MCB Terminal Blocks etc. The feeder above shall be provided ac accommodated all measuring instrument shall be digital type & all indicating lights ahall be LED type. Wiring shall be done from 1100V Grade PVC Insulated copper flexible wire. All ACB shall be electricaly operated Draw out Type with microprosser based O/L, S/C & E/F Release off Breking/withstand capacity(ICU/ICs/Icw) 50 kA or more. All MCCB shall be thermal magnetics/microprossor with O/L & S/C protection along with required Spreders Extended rotary handle with pad locking facility of bracking capacity(ICU/ICS) 36 kA or more All MCB shall be Thermal 10kA 'C'Curve Cubical type switch board shall be Cat-A and B only.

Incoming :

630 Amp. MCCB - 1No

Cat. B Panel Cubicale Type

Metering :

One (1) Set of Phase Indication Lamp.

Bus Bar :

One (1) No. 800 A, TPN aluminimum bus bar of suitable length.

Outgoing :

Phase indication lamps on each outgoing to be provided.

400 Amp. 4P MCCB- 1 No.

63 Amp. 4P MCB- 15 No.

125 Amp. 4P MCCB- 1 No. Spare

63 Amp. 4P MCB- 1 No. Spare

40 Amp. 4P MCB- 1 No. Spare

OR outgoing as per site requirment(AS/SLD)

With provision for meter space

EM-L.T. PANEL(LOC-STILT FLOOR)

Incoming :

400 Amp. MCCB - 2No

Cat. B Panel Cubicale Type

Metering :

One (1) Set of Phase Indication Lamp.

Bus Bar :

One (1) No.500 A, TPN aluminimum bus bar of suitable length.

Outgoing :

Phase indication lamps on each outgoing to be provided.

100 Amp. 4P MCCB- 1 No.

63 Amp. 4P MCB- 2 No.

40 Amp. 4P MCB- 9 No.

25 Amp. DP MCB- 2 No.

125 Amp. 4P MCCB- 1 No. Spare

63 Amp. 4P MCB- 1 No. Spare

40 Amp. 4P MCB- 1 No. Spare

OR outgoing as per site requirment(AS/SLD)

With provison of Meter & AMF Interlocking

Supply of following size of 1.1 KV grade multicore aluminium conductor PVC sheathed armoured cable as per IS 1554. Make-Polycab or Eq

6 sqmm 2 core

10 sqmm 2 core

10 sqmm 4 core

35 sqmm 3.5 core

300 sqmm 3.5 core

Supply & Fixing of 1X17 W mirror light complete in all respects. Make-Philips or Equivalent

Providing, supplying, installation, testing and commissioning of 12 Watt LED bulb. Make-Philips or Equivalent

Providing, supplying, installation, testing and commissioning of LED ceiling light fitting of 12–15 Watt, square or round type, surface mounted, high lumen efficiency, complete with driver, internal wiring, fixing accessories and all connections, as required at site.

Providing, supplying, installation, testing and commissioning of LED tube light fitting 18–22 Watt, complete with LED batten, driver, internal wiring, fixing accessories and all required connections, as required at site.

Providing, supplying, installation, testing and commissioning of 40 Watt LED tube light fitting, high efficiency type, complete with batten, driver, internal wiring, fixing hardware and all accessories, as required at site.

Providing, supplying, installation, testing and commissioning of LED street light luminaire of 100 Watt, complete with driver, mounting brackets and all accessories, as required at site.

Providing, supplying, installation, testing and commissioning of LED Flood light luminaire of 100 Watt, complete with driver, mounting brackets and all accessories, as required at site.

Providing, supplying, installation, testing and commissioning of 1200 mm sweep ceiling fan, energy efficient, complete with down rod, shackle assembly, ceiling rose, required wiring connections and all accessories, as required at site.

Providing, supplying, installation, testing and commissioning of 300 mm sweep exhaust fan, heavy duty type, necessary wiring connections, fixing accessories and all required materials, as required at site.

Supply and fixing following rateing four pole, 415 V, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required.

40 A,4P MCB-Bracking Capacity-10 kA, C-Curve-Make-Havells OR Equivalent

63 A,4P MCB-Bracking Capacity-10 kA, C-Curve-Make-Havells or Equivalent

Providing, supplying, erection, testing and commissioning of 7.0 meter high hot dip galvanized octagonal steel pole, suitable for mounting of LED street light luminaire, complete with base plate, anchor bolts, nuts & bolts, foundation bolts, all required accessories, including alignment and making the pole operational, as required at site.

Providing, supplying and fixing of 1.5 meter long single arm bracket, made of GI pipe, hot dip galvanized, suitable for mounting of two LED luminaires, complete with clamps, fasteners, welding, painting and accessories.

Providing, supplying and fixing of 3 meter long double arm bracket, made of GI pipe, hot dip galvanized, suitable for mounting of two LED luminaires, complete with clamps, fasteners, welding, painting and accessories.

Supply and fixing of Single Unit LED aviation obstruction light complete with Transformer and LED spiral etc. complete in all respects.

LIGHTING ARRESTER

Supply & fixing of level-I tested accordance with NFC-17-102 for advance triggering time 22 micro seconds, temperature with stand test of -40 to +120 degree centigrate, CE marked, short circuit test for 100KA etc. inculding the following: Make Liva/ESE(kalre)-50mtr. or equivalent

SITC 5m GI mast with adaptor head and base plate for raising the lighting rod by 5 m above the surface to protected including insulator between lighting rod and GI mast.

SITC Copper cable 70 sqmm flexible copper single core multi-strand.

SITC 6 digits IP 67 lighting counter with hole for cable/strip LEC-D

SITC Eathing set(2 Nos.) consisting of copper bounded rod 17.2mm dia 10ft long 250 microns UL marked, 30kg earth enhancing chemical compound with resistivity of <0.1 Ohm-m NABL lab tested, clamp for connecting rod to cable/strip including civil work with pit cover complete.

SITC stay wire,lugs, U clam, base plate fastener, hook fasteners, Test link/clamp ect. As required complete.

L.T. FEEDER PILLER

Supplying assembling erecting connecting, testing and commissioning of feeder pillar with over voltage and under voltage relay with auto re-setting, manufactured using 1.9/1.6 mm thick CRCA sheet steel with power coated paint double door (front operated)with canopy base channel and cable gland entry from bottom for cable using, suitable alluminium busbar with provision of incoming & outgoing MCCB/MCB of L&T/Schneider/GE/ABB or Eq. make. Installation of feeder pillar of suitable c.c. foundation etc complete in all respect.

Incoming :

1No. Of 630 Amps TPN MCCB of 36 KA service breaking capacity and 630 Amp trip setting.

Metering : Voltmeter, Ammeter, Indication

Bus Bar :

1 Set of 800 Amps TPN Aluminium Bus Bars of suitable length and of cross section . Bus bar shall be insulated by heat shrinkable sleaves & clip on shrouds for joints. Bus bar shall be designed to with stand a fault level of 36 KA at 415 volts.

3Nos. Phase indicating lamp each lamp shall have one toggle switch .

Outgoing :

Phase indication lamps on each outgoing to be provided.

630Amp 4P MCCB (36kA) - 1 Nos.

40Amp 4P MCB (10kA) - 1 Nos.

PASSENGER ELEVATOR

Design, manufacturing, testing at works, supply and delivery, receiving, unloading, storing, inspection, handling, assembling, installing in correct assigned position, effecting proper connections, testing and commissioning of Elevator of 13-15 passenger/1020 Kg. MRL with variable voltage variable frequency drive having a speed of 1 metre/ sec with 8 Stops, 2 opening same side, approx. 900 mm Door Width, 2000 mm Height, and ACD5-MRL controler type suitable for operation with VF regenerative drive closed loop 415 V, 50 Hz, 3 phase A.C. electric supply as required with Car, Central Opening Car Door & other features with all associated electrics & civil works as per requirement at site. Make: OTIS

CCTV CAMERA SYSTEM

4MP IP Bullet Camera. Make: CP Plus or equivalent

VMS Software for 128 Cameras for live view/playback. (We will provide the sofware given by CP Plus through a link which is generated after taking the server MAC Address and then the software is provided to you in a Pen drive). Make: CP Plus or equivalent

Desktop Server with Intel i7 Processor, 16GB RAM, Windows 11 or compatible, SSD 500GB, Gigabyte Motherboard complete with Keyboard and Mouse, Hard Disc 4 Terabyte, Graphics Card with Antivirus or better which supports the VMS.

32 Channel NVR with 4 SATA support. Make: CP Plus or equivalent

Surveillance Hard Disc 8TB. Make: WD/Seagate or equivalent

4 Port Gigabit POE Switch. Make: Dlink or equivalent

8 Port Gigabit POE Switch. Make: Dlink or equivalent

5 Port Gigabit Network Switch. Make: Dlink or equivalent

8 Port Gigabit Network Switch. Make: Dlink or equivalent

Outdoor Weatherproof PVC Box with inbuilt supply board.

PVC Box for Camera.

Metal Cage for Outdoor Cameras.

Server Rack 42U with PDU, Fan, tray, cable manager etc. Make: Digirack or equivalent

Mount for Bullet Camera for Pole.

55” HD LED TV. Make: Samsung or equivalent

Media Convertor.

Fibre Junction Box with Accessories.

2” MS Pole for Cameras, pole height 15' length with pole fixing and Civil work.

12 Core Fiber Cable.

Installation and Configuration Charges of IP Cameras

Cat-6 Cable 4 Pair. Make: Dlink or equivalent

Outdoor Cat-6 Cable 4 Pair. Make: Dlink or equivalent

2-Core 1.5 sq.mm. Supply Cable. Make: Polycab or equivalent

Cable Laying charges on surface

Cable Laying charges underground/in soft soil

Splicing Charges for Fiber Cable

VMS Software Installation, System Integration and Configuration Charges

Online UPS 6KVA with 7AH 12 V* Battery with alarms like overload, overcharge, low battery, discharge protection (*or as applicable for existing system. Make: BPE or equivalent

PVC Pipe with accessories. Make: ISI Medium

Support Wire.

CCTV – Surveillance Signage’s (Throughout the Campus- Inside & outside).

TELEPHONE SYSTEM

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.

1 or 2 Module

3 Module

4 Module

Supplying, laying, testing and commissioning of following size anealed tinned copper conductor PVC insulated and sheathed armoured copper telephone cables direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Supplying, installing, testing and commissioning of 48 Extension EPABX system including necessary fitting and accessories as per site requirement. Make: Kolhar NEC or equivalent.

Providing and installation of caller ID corded landline phone with 16 digit LCD display and adjustable contrast, two ways speaker phone, 13 incoming and 5 outgoing memory along with necessary wiring and accessories as per requirement. Make: Beetel or equivalent

FURNITURE WORK

Design, manufacture, supply and installation of single wooden bed with storage, overall size approximately 2030 mm (L) × 920 mm (W), with headboard height around 900 mm, complete as per approved drawing and sample. The bed storage box including side panels, head side, foot side and base panel shall be constructed from 18 mm thick plywood, finished on both faces with decorative laminate of approved colour and shade. Mattress support panels shall also be provided in 18 mm thick laminated plywood. The overall height of the storage box shall be approximately 380 mm. The headboard and footboard shall be made from laminated plywood panels of suitable thickness and dimensions, with smooth, rounded and uniform exposed edges. All visible edges shall be machine-finished with PVC edge banding, and all concealed edges shall be properly sealed to prevent moisture ingress. All wooden surfaces shall have a scratch-resistant and easy-to-maintain finish. All fittings and accessories such as hinges, box hardware, connectors, fasteners and handles shall be of approved make (Godrej, Harrison, or equivalent). Plywood and laminate shall be sourced from approved manufacturers only. The complete bed shall be installed, aligned, tested and finished at site to the satisfaction of the Engineer-in-Charge, complete in all respects. The dimensions mentioned are approximate and may vary slightly depending on site conditions and material availability.

Design, supply and fixing of bedside table with storage, comprising one lockable drawer and one open compartment, of approximate overall dimensions 450 mm (D) × 440 mm (W) × 510 mm (H), complete as per approved sample, drawing and site requirements. The carcass, drawer box and shutters shall be fabricated from 18 mm thick plywood, factory finished on both faces with decorative laminate of approved colour and shade. All visible edges shall be finished with machine-applied PVC edge banding, while all concealed edges shall be properly sealed and ensure smooth handling. All wooden panels shall have a scratch-resistant surface finish suitable for regular use. The drawer shall be provided with an approved locking arrangement and mounted on smooth-operating drawer channels. All fittings and accessories, including drawer channels, hinges, handles, locking system and fixing hardware, shall be of reputed make such as Godrej / Harrison or equivalent, as approved by the Engineer-in-Charge. Plywood and laminate shall be sourced from approved manufacturers only. The complete bedside table shall be installed, aligned, levelled and finished at site to the satisfaction of the Engineer-in-Charge. The dimensions mentioned are approximate and may vary slightly depending on site conditions and material availability.

Providing and supplying single bed mattress of approximate size 1830 mm × 915 mm, with finished thickness up to 150 mm, suitable for use with a standard single bed, complete as per approved sample. The mattress shall be of multi-layer construction and finished to ensure uniform support. The mattress shall be of reversible type, with quilting on both faces, using materials to provide cushioning and long-term comfort. The core and comfort layers shall conform to the specified density and performance requirements. The complete mattress shall be finished with proper edge sealing and an appropriate quilting pattern, suitable for regular institutional use such as hostel environments. The mattress shall be of approved make such as Sleepwell / Kurlon or equivalent, and shall be supplied complete in all respects, as approved by the Engineer-in-Charge. The dimensions mentioned are approximate and may vary slightly depending on site conditions and material availability.

Providing and supplying single bed sheet of approximate finished size 1520 mm × 2540 mm, manufactured from high-quality cotton fabric with a smooth satin stripe weave. The bed sheet shall be made from cotton yarn, offering softness, durability and comfort suitable for regular institutional use. The fabric shall be colourfast, breathable, and capable of withstanding repeated washing without significant shrinkage or loss of finish. The bed sheet shall be of reputed manufacture such as Bombay Dyeing or equivalent, duly approved by the Engineer-in-Charge, and supplied complete in all respects. The dimensions mentioned are approximate and may vary slightly depending on site conditions and material availability.

Providing and supplying bed pillow complete with removable fabric cover, of approximate finished size 430 mm × 680 mm, suitable for institutional use. The pillow shall be rectangular in shape with uniform filling to achieve a finished weight ensuring adequate comfort and support. The outer cover shall be manufactured from high-quality combed cotton fabric, designed to withstand repeated washing without loss of shape. The pillow and cover shall be neatly finished. The product shall be easy to wash and dry and suitable for regular use in hostel accommodation. The pillow with cover shall be supplied as a complete unit and shall conform to the approved sample and specification, to the satisfaction of the Engineer-in-Charge. The dimensions mentioned are approximate and may vary slightly depending on site conditions and material availability.

Providing, supplying and placing 3-seater upholstered sofa of approximate size 2060 mm (W) × 905 mm (D) × 855 mm (H), having an internal frame made of well-seasoned hardwood. The seat cushion, back cushion, and arm/back padding shall be made with suitable foam, as required. The sofa shall be fully upholstered in approved quality leatherette / fabric, with neat stitching and proper finish. The seat height shall be approximately 450 mm, and the base height shall be 200–250 mm. The sofa shall be complete in all respects and as approved by the Engineer-in-Charge / Employer. The dimensions mentioned are approximate and may vary slightly depending on site conditions and material availability.

Supply, installation and positioning of 2-seater sofa of approximate size 1460 mm (W) × 905 mm (D) × 855 mm (H), with seat height about 450 mm, constructed on a hardwood internal frame. The seat cushion, back cushion, and side/back padding shall be made with suitable foam to provide comfort and shape retention. The sofa shall be fully upholstered in approved leatherette / fabric, with neat stitching and proper finish. It shall be complete with all necessary fittings and accessories, as approved by the Engineer-in-Charge / Employer. The dimensions mentioned are approximate and may vary slightly depending on site conditions and material availability.

Supply and installation of Stainless Steel 304 three-seater waiting chair, with frame and cross beam made of SS 304 stainless steel, complete in all respects. The chair shall be of approved design, sturdy construction and suitable for institutional use, as approved by the Engineer-in-Charge / Employer. The dimensions mentioned are approximate and may vary slightly depending on site conditions and material availability.

Design, supply and installation of factory-finished wooden wardrobe of overall size 6’-0” (H) × 3’-0” (W), with approximate depth between 450 mm to 600 mm, complete in all respects. The carcass, shutters and internal partitions shall be manufactured from high-density boards of minimum 18 mm thickness, finished with decorative laminate on both faces. All visible edges shall be finished using PVC edge strips. Back panels and drawer bases shall be provided in 18 mm thick laminated boards. The wardrobe shall be provided with either hinged or sliding shutters, as approved at site. All fittings and accessories, including concealed hinges, telescopic drawer channels, locking arrangement and handles, shall be of reputed make such as Godrej / Harrison or equivalent, duly approved by the Engineer-in-Charge. Boards and laminates shall be sourced from approved manufacturers, and the complete wardrobe shall be erected, levelled and finished at site to the satisfaction of the Engineer-in-Charge. The dimensions mentioned are approximate and may vary slightly depending on site conditions and material availability.

Supply and installation of office table of approximate size 1200 mm (W) × 600 mm (D) × 750 mm (H), complete in all respects. The table shall have all exposed edges finished with PVC edge banding. The drawer pedestal comprising one drawer and one file cabinet shall be made of 18 mm thick board with PVC edge banding, provided with smooth-operating drawer slides and central locking arrangement. All wooden surfaces shall be scratch-resistant. All hardware and fittings, including handles, slides, hinges, locks, dowels and screws, shall be of premium quality from Godrej / Harrison or equivalent, as approved by the Engineer-in-Charge. The final design shall be as per the approval of the Engineer-in-Charge. The dimensions mentioned are approximate and may vary slightly depending on site conditions and material availability.

Supply and installation of study chair with cushioned seat and back, suitable for office / institutional use, complete in all respects. The chair shall have an ergonomically designed seat and back for user comfort, with adjustable armrests, lumbar support, and pneumatic height adjustment. The chair shall be provided with a tilting mechanism with 360° swivel rotation, smooth height adjustment and stable base with castor wheels for easy movement. Upholstery shall be in approved quality fabric and mesh, with neat finishing and proper workmanship. The study chair shall be of approved design and make, sturdy in construction and suitable for regular institutional use, as approved by the Engineer-in-Charge / Employer. The dimensions mentioned are approximate and may vary slightly depending on site conditions and material availability.

Supply and installation of centre table of approximate size 1200 mm (W) × 600 mm (D) × 400 mm (H), complete in all respects. The table shall be construction with a smooth finished top, suitable for office / institutional use. The centre table shall be of approved design, good workmanship and neat finish, complete with all necessary fittings and accessories, as approved by the Engineer-in-Charge / Employer. The dimensions mentioned are approximate and may vary slightly depending on site conditions and material availability.

Supply and installation of a Corner table of size 500mm W × 500mm D × 400mm H. The table shall be construction with a smooth finished top, suitable for office / institutional use. The centre table shall be of approved design, good workmanship and neat finish, complete with all necessary fittings and accessories, as approved by the Engineer-in-Charge / Employer. The dimensions mentioned are approximate and may vary slightly depending on site conditions and material availability.

Supply and installation of a 15-liter stainless steel dustbin (approx. 10" × 14") with lid and handle, made of SS 304 non-magnetic steel. The dustbin shall be pedal-operated or as approved by the Engineer-in-Charge / Employer. The dimensions mentioned are approximate and may vary slightly depending on site conditions and material availability.

Supply and installation of roller blinds (blackout or translucent) in required dimensions, as per specifications.

Please Enable Macros to View BoQ information