P/f of PUF Panel in Seismography room at IISER Mohali

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Electric resistance or induction butt welded tubes

Providing and fixing bolts including nuts and washers complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Glazed Vitrified tiles Matt/Antiskid finish of size

Size of Tile 600 x 600 mm

Providing and fixing of PUF Wall Panel , CR 80, 80mm thick puf panel comprising to two sides facing of colour coated galvanized steel sheet and sandwiched between them HCFC & CFC free close cell, high density rigid polyurethane foam (40 ± 2 kg/m3) having a thermal conductivity value of 0.023 w/mk and thickness 80mm. Both sides steel sheet shall be of 0.50mm TCT,PPGL having coating of 150Gsm (Zn Al) finished with 16-20 microns colur coating of regular modified polyester quality paint coat over a 5 micron primer on exposed side and a back coat of 5 microns on inner side over a 5 micron primer. Both side sheet shall be slightly ribbed / plain facing as per requirement.The panels should be of required length and 1mt effective cover width made on continuous line using N pentane as blowing agent. The panels shall have tongue and groove joint and shall be supplied with protective guard film to avoid scratched during transportation.Color as per direction of Engineer-Incharge

Providing and fixing of PUF Roof Panel , CR 80 (80/122), 80mm thick puf panel comprising to two sides facing of colour coated galvanized steel sheet and sandwiched between them HCFC & CFC free close cell, high density rigid polyurethane foam (40 ± 2 kg/m3) having a thermal conductivity value of 0.023 w/mk and thickness 80mm. The top side sheet shall be trapazoidical profile of crest height 42mm with pitch distance of 333mm while bottom side sheet shall be slightly ribbed. Both side sheet shall be 0.50mm TCT,PPGL having coating of 150Gsm (Zn Al) finished with 16-20 microns colur coating of regular modified polyester quality paint coat over a 5 micron primer on exposed side and a back coat of 5 microns on inner side over a 5 micron primer. The panels should be of required length and 1mt effective cover width made on continuous line using N pentane as blowing agent. The panels shall have male female joint and shall be supplied with protective guard film to avoid scratched during transportation.Color as per direction of engineer incharge.

Providing and fixing of Flashings Girth 0-305mm, Profile Flashing, U flashing, Side Covers etc as per direction of engineer incharges

Providing and fixing of Flashings Girth 306-610mm, Ridges, Eaves Flashings etc as per direction of engineer incharge.

Providing and fixing of Door- Single Door Size for Scientific Metal Doors designed to fit flush into the wall panel and brick wall. Doors are fabricated from GI sheet duly powder coated (thick 70-80 micron with approved color). Leaf having sheet thickness of 0.8mm and the frame of 1.2mm. Infill material will be Paper core with double glazing toughened glass 400*600mm STD Arm Door closure SS ball bearing hinges SS D handle B2B 250mm Dead lock both side key Operated Door Drop Seal Door Seal D type SS kick plate 300mm height Concealed tower bolt for the double door etc.

Providing and fixing aluminum sliding window of aluminium section 1.5mm thicknes and glass 3.5mm with aluminium grill, mosquito net , complete in all respect as per diection of engineer incharge .