REPAIR TO KITCHEN PLASTERING JOINERY AND SANITARY FITTINGS IN OLD RATC AREA UNDER GE W MATHURA

Amount

Taking down chowkat or frame with shutters including fitting and fixtures area not exc 1.5 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts and making good disturbed surface with cement mortor or PCC after fixing new chowkats complete all as specified and directed by Engineer-in-charge.

Taking down chowkat or frame with shutters including fitting and fixtures area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the wooden shutters from the frame) including cutting holes for hold fasts and making good disturbed surface with cement mortor or PCC after fixing new chowkats complete all as specified and directed by Engineer-in-charge.

Taking down shutters of any description exc 1 Sqm and not exc. 2 Sqm each complete all as specified and as directed by Engineer-in-charge.

S&F pressed steel frames for door of size 125x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc made out of mild steel sheet of 1.25mm thickness complete all as specified and as directed by Engineer-in-charge.

S&F pressed steel frames for door of size 105x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc made out of mild steel sheet of 1.25mm thickness complete all as specified and as directed by Engineer-in-charge.

M&L for PCC (1:3:6) type C-0 using 12.5 mm graded stone aggregate as in filling of pressed steel frame complete all as specified and as directed.

S&F 35 mm thick factory made plain framed, panelled shutter (any number of panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces. The size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood (Hollock or Bonsum) complete all as specified and directed by Engineer-in-charge.

S&F for 30mm thick flush shutter solid core construction with block board core & ply wood face panels, commercial type on both faces complete all as specified and directed by Engineer-in-charge.

M&L 35mm thick factory made glazed and skeleton shutters of 2nd class HW with partially panel shutter open rebated and prepared to receive glass / gauze etc edges or framing plain chamfered or rounded fitted with cut or mitred beads for securing glass etc as specified in SSR Part-1 section 8.24 (a) complete all as specified and directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified & shown in relevant drawing of item No. 08095 in MES Schedule (Part-II) and directed by Engineer-in-Charge

S&F 28 to 30mm thick (stiles) factory made solid PVC moulded Door shutter, with 2, 4, or 6 raised panel design with 2mm thick moulded prelaminated PVC sheet on the front face & 2mm thick prelaminated PVC sheet on back face complete all as specified & shown in relevant drawing of item No. 8101 to 8105 in MES Schedule (Part-II) and directed by Engineer-in-Charge.

S&F Mild Steel 300mm, ordinary rat tail rod patttern springs including roller & roller plate fixed to wooden frame or welded to steel frame making suitable cut out in wall and making good in CM 1:4 complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

S&F 100mm long stainless steel Butt hinges fixed complete all as specified and directed.

S&F 150mm stainless steel barrel tower bolts with bright bolt and fixed complete all as specified and directed.

S&F 150mm long stainless steel handles, oval type complete all as specified and directed.

S&F 300mm stainless steel sliding door bolts, bolt type with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F in repair floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring overall length of cover plate 140mm (ISI marked) complete all as specified and directed by Engineer-in-Charge.

S&F Factory made steel windows with side hung shutters including box type hinges with steel handle & steel peg stay complete with glazing bars, dovetailed or welded and also including painting the exposed steel surfaces with one shop coat of Zinc-Chromate primer complete all as specified and directed.

S&F Factory made steel windows with side hung shutters including box type hinges with steel handle & steel peg stay complete without glazing bars, dovetailed or welded and also including painting the exposed steel surfaces with one shop coat of Zinc-Chromate primer complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer-in-charge.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, cooler stand 12mm sq guard bar, framework of water tanks and similar works of quality Fe 290 (Gde E-165) etc complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-charge.

M&L for preparation of steel surface already treated with primer over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed by Engineer-in-charge.

M&L for non skid joint free ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6) complete all as specified and directed by Engineer-in-charge.

M&L for glazed ceramic tiles (coloured) 450mm x 300mm x 8-9mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick rendering in cement & sand mortar (1:4) including necesary cutting as per site requirment complete all as specified and directed by Engineer-in-charge.

M&L for non skid joint free ceramic white coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6) complete all as specified and directed by Engineer-in-charge.

M&L for non skid joint free ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar (1:4) complete all as specified and directed by Engineer-in-charge.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded, jointed and pointed in any mortar complete all as specified and directed by Engineer-in-charge.

M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) for Shelves (veneering to wall) including 15mm thick plaster in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M&L for machine cut Kota stone slab 18 to 20mm thick (minimum size 550mm x 550mm or size as directed) in floor, tread of steps & cooking platfrom laid over & including screed bed or bedding layer of 20mm thick in CM (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed by Engineer-in-charge.

M&L for machine cut Kota stone slab 18 to 20mm thick (minimum size 550mm x 100mm or size as directed), on vertical surfaces such as dado, skirting, raiser of steps etc. laid over & including rendering 15mm thick in CM (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting, grinding, rubbing and mirror polishing complete all as specified and directed by Engineer-in-charge.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations etc complete all as specified and directed.

Demolition of brick work, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by Engineer-in-charge.

M&L for Brick work with sub class ‘B’ old size burnt bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engineer-in-charge.

Taking down cement plaster or cement lime plaster on stone surface/brick surfaces of walls including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-charge.

M&L for 15mm thick rendering in cement mortar (1:4) on fair faced or on other than fair face surface of brick masonary or concrete surface of walls, finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for 15mm thick rendering on external stone wall surfaces in cement mortar (1:6) finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for preparation of newly plastered surface of walls & applying two coats of cement base paint by roller of approved shade/tint and filling cement based putty in cracks complete all as specified and directed by Engineer-in-charge.

M&L for preparation of new plastered and unplastered surfaces of wall and applying two coats of oil bound distemper including one coat of primer preparatory to distempering using roller complete all as specified & directed by Engineer-in-Charge.

M&L for rendering dubbing coat over irregular surfaces of chajjas roof projections/ceiling/facia etc average 15mm thick in CM (1:4) over cement slurry coat @ 3Kg/Sqm making the surface even followed by 5mm thick rendering in CM (1:3) furnished even & smooth including making of drip course as required complete including roughening surface of old concrete by picking sweeping clean and washing with water complete all as specified and directed. Note : Rate for form work if required to be included in the quoted rate by the contrator.

Taking up or down 15mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down 20mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

S&F 15mm bore galvanized steel water tubing medium grade with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-charge.

S&F 20mm bore galvanized steel water tubing medium grade with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-charge.

Taking down wornout existing treatment from sunken portion of WC /Bath/Kitchen/Passage area n exc 2.5 Sqm each including taking down floor tiles, plaster, lime/cement concrete, WC trap complete empty of existing sunk. (Taking down of plumbing & sanitary fixing & fixture shall be measured under relevant items).

M&L for Cement concrete (1:4:8) type D2 using 40mm graded stone aggregate as in sunken portion complete all as specified and directed.

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces finished fair and even in CM (1:3) mixed with liquid water proofing compound complete all as specified and directed. Note:- Liquid WPC shall be measured and paid saperately.

Supply only liquid water proofing compound ISI marked complete all as specified and directed by Engineer-in-charge

S&F in repair vitreous china squatting pan Orissa pattern, white of size 580x440mm with integral foot rests (excluding flushing cistern and flush pipe) including cast iron 'P' or 'S' trap, PCC filling and connection to trap and flushing pipe, antisyphonage pipe etc complete all as specified and directed by Engineer-in-charge.

S&F in repair 10 litre capacity PVC valveless symphonic action type low level flushing cistern (ISI marked) including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified and directed by Engineer-in-charge.

S&F GI spout pipe 50 mm dia tubes,light grade galvanised, with all fitting, laid in treanches complete all as specified and as directed.

Opening of air lock/blockage in GI pipe line from outlet of water tank to all internal GI pipes/fittings for smooth flow of water from bib taps/showers/WHB pillar tap/stop valves complete by air pressure/water gravity pressure, complete all as specified and directed.

S&F in repair Stainless steel gratings 100mm bore size fixed with white cement, complete all as specified and directed.

S&F in repair PVC cover suitable for PVC Water tank 500/750/1000ltr cap with self locking arrangement fixed with 4 nuts & bolts complete all as specified and directed.

S&F in repair PVC Syphon kit assembly in existing flush tank complete all as specified and directed.

S&F in repair PVC mirror cabinet size 350X450mm of standard size fixed to wall with PVC sleeves and steel screws complete all as specified and directed.

S&F in repair Glass shelf 450mm long x 100 mm wide including brackets fixed to wall with sleeves and screws complete all as specified and directed.

S&F in repair corner glass shelf of size 300X300 mm including brackets fixed to wall with pvc sleeves and stainless steel screw complete all as specified and directed.

S&F in repair vitreous china full stall type, flat back urinal white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified and directed by Engineer-in-charge.

S&F in repair vitreous china wash basin white, flat back of size 550x400mm including including a pair of cast iron brackets embedded in PCC 1:3:6 type C-1 blocks of size 10 x 7.5 x15 cm with pair of fastner including 32 mm dia PVC waste pipe, 32mm dia PTMT waste coupling half or full thread (minimum wt 45 grms) flange end bedded in red lead cement & other end fixed to waste pipe and including brass chromium plated fancy type pillar tap, screwed suitable for iron pipes of 15mm bore complete all as specified and directed by Engineer-in-Charge.

S&F in repair chromium plated shower rose with or without swivel joints including fixing to steel pipe of 125 mm size complete all as specified and directed.

S&F in repair CP Jet spary butter fly design fixed on EWC with stanless screw as approve complete all as specified and directed.

S&F in repair CP Health faucet with stand fixed on wall in CP hose pipe 1 mtr length and stainless steel screw as approve complete all as specified and directed.

S&F in repair stainless steel kitchen sink 1 mm thick kitchen/laboratories with plug washer and waste including bedding in cement mortar and fixing cantilever brackets and connecting union to pipe overall size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F in replacement 600mm long PVC connection suitable for 15 mm bore with PTMT nuts on both sides complete all as specified and directed by Engineer-in-charge.

S&F in replacement 450mm long PVC connection suitable for 15 mm bore with PTMT nuts on both sides complete all as specified and directed by Engineer-in-charge.

S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device and jet spray complete all as specified & as directed by Engineer-in-charge.

S&F in repair PVC EWC seat cover of any type, colour & make suitable for pedestal pan complete all as specified and directed.

M&L for water proofing treatment with APP modified bituminous membrane 3mm thick consisting of the following for RCC roof :- (a) Cleaning palstered roof surfaces and applying a coat of oxidised bitumen based solvented primer @ 0.3Kg /Sqm of approved make on top of dry surface of RCC roof complete all as specified and directed. (b) M&L for APP modified polymeric water proofing membrance 3mm thick weight not less than 3.0 Kg/Sqm with non woven polyster core of approved make applied by heating one surface of membrane with LPG torch with lap of 100mm and the overlap shall be sealed by flame complete all as specified and directed.

S&F for repair 32mm Waste fittings, brass, chromium plated for glazed ware wash hand basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified.

S&F for repair 40mm Waste fittings, brass, chromium plated for glazed ware wash hand basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified.

M&L for applying a coat of two component elastomeric acrylic polymer modified cementitious water proofing coating, having properties of 80 % elongation as per ASTM D412, resisting 5 bars hyrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per DIN 1048, crack bridging upto 1.2mm as per ASTM 4548.5. The mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing, etc., complete as per manufacturers specifications and sprinkle sand at 10-15 gram per sqft for better grip with plaster complete all as specified and directed.

Disconnecting existing tank of capacity 500 litre to 1000 litre, setting aside (or lowering if required) for repairs, cleaning and removing all scale and dirt etc from tanks and from mouth of circulating pipe etc including writing with white paint (Date of cleaning), hoisting if required, reconnecting and re-fixing in position complete all as specified and directed.

Disconnecting existing tank of capacity 250 litre to 500 litre, setting aside (or lowering if required) for repairs, cleaning and removing all scale and dirt etc from tanks and from mouth of circulating pipe etc including writing with white paint (Date of cleaning), hoisting if required, reconnecting and re-fixing in position complete all as specified and directed.

S&F 750 ltr capacity Rotational moulded polythene water storage tank white colour in triple layer (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of tanks & float valve complete all as specified and as directed.

S&F in repairs 125 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed by Engineer-in-charge.

S&F in repairs 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed by Engineer-in-charge.

S&F in repairs 250mm long aluminium alloy anodised sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy (ISI marked) complete all as specified & directed by Engineer-in-Charge.

S&F in repairs Aluminium handles fabricated type anodised of size 125mm long, complete all as specified and directed.

S&F in repair 15mm bore PTMT bib tap of any colour high pressure, screwed for iron pipe (minimum weight 90 grams) complete all as specified and directed by Engineer-in-charge.

S&F in repair 15mm bore PTMT stop valve of any colour high pressure, screwed for iron pipe (minimum weight 90 grams) complete all as specified and directed by Engineer-in-charge.

S&F in repair float valve of 20 mm dia PTMT valves, high pressure with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F 15mm bore chromium plated bib tap cast copper alloy fancy type (min weight 350 gm) screwed down, screwed for iron pipe or for brass ferrule and fix complete all as specified and directed.

S&F 15mm bore CP pillar taps Fancy type cast copper alloy (min weight 350 gm) along screwed down high pressure with lettered hot & cold with long screwed shanks and fly nuts screwed for GI pipe complete all as specified and directed.

S&F in repair 15mm bore stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-charge.

S&F in repairs PVC waste pipe 32mm dia of length 0.8mm to 0.9mm fixed complete all as specified and directed.

S&F in replacement 18mm thick PVC Celuka Ply plain white colour both side fixed with screws solvent cement/adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinets complete as per specifications and as directed by the Engineer-in-Charge (Density - 575 to 600 Kg/CBM)

S&F in replacement 18 MM thick PVC Celuka board of single side prelam/rigidlam color fixed with screws, solvent cement/adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinet, cupboard shutters/frames, (Density- 575 to 600 Kg/ CBM), complete, all as directed by Engineer-in-Charge.

S&F mild steel framed work as in doors / gates / steel frames etc. of angle or other section with gusset plates, rails, braces, etc, complete, drilled for fixing of steel sheeting or other covering including necessary welding etc and fixing in position of quality Fe 290 (Gde E-165) complete all as specified and directed by Engineer-in-charge.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified and as directed.

S&F powder coated aluminium anodised door frame and shutter of section as under and providing 5.50mm thick tinted gass with and including each shutter to be provided with aluminium fittings such as aluminum butt hinges 100mm- 03 Nos, Aluminum handles 150mm- 02 Nos, Aluminium tower bolts 150mm- 02 Nos, rubber neopran beadding, glazing clips and one lock four lever with duplicate keys of make Godrej or equivalent in each opening and 01 No hydraluic door spring etc complete all as specified and directed. Taking down old Aluminium door shutter with chowkhat :- (a) Outer Frame - 100x50x1.20mm (b) Shutter - 90x50x1.20mm (c) Top, middle & Bottom rail 90x50x1.20mm etc

M&L for in repair aluminium door/window of any size/any description and refixing in the same opening after tightening , easing/change the section as required , including fitting the rubber packing aluminium snap beading resetting floor/hydraulic door closer/spring etc complete all as specified and directed.

S&F in replacement 12mm thick celuka ply of plain white (Matt finish) color fixed with screw, solvent cement/adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per directed by the Engineer-in-Charge (Density - 575 to 600 Kg/CBM)

S&F hollow corrugated shape PVC wall lining consisting of 5mm thick decorative colour PVC sheet inclusive of solvent cement and fixing and incl beading at sides on PVC frame as per specifications all as specifed complete all as specified and directed.

S&F auto closing hinges 35mm of 0 crank (KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete all as specified and directed.

S&F Continuous (piano) hinges 40 mm, mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length jointed with adhesive fixed to walls fixed with and including requisite Number of clamps made out of flat iron 25x4mm including taking down old unserviceable pipe and fittings complete all as specified and as directed by Engineer-in-charge.

S&F 100mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length jointed with adhesive fixed to walls fixed with and including requisite Number of clamps made out of flat iron 25x4mm including taking down old unserviceable pipe and fittings complete all as specified and as directed by Engineer-in-charge.

S&F 110 mm bore PVC (SWR) bends any radius jointed with adhesive with oval access door complete all as specified and as directed by Engineer-in-charge.

S&F 110mm bore PVC (SWR) junction, single (single T) equal or unequal complete all as specified and directed by Engineer-in-Charge.

S&F 110mm bore PVC (SWR) junction, double (double T) equal or unequal complete all as specified and directed by Engineer-in-Charge.

S&F in repairs stack clamps mode out of 25x3mm flat iron including bolts and nuts and securing ends of stays to wall or roof, for 100mm bore pipes, complete all as specified and directed.

S&F in repairs stack clamps mode out of 25x3mm flat iron including bolts and nuts and securing ends of stays to wall or roof, for 75mm bore pipes, complete all as specified and directed.

S&F in repair aluminium (Die cast) body door closer hydraulically regulated, designation No. 3 universal type, suitable for door shutters of 851 to 1000mm in width and weight between 61 to 80kg (ISI marked) complete all as specified and directed by Engineer-in-Charge.

S&F in repair stainless steel kitchen sink 1 mm thick with drainage board kitchen/laboratories with plug washer and waste including bedding in cement mortar and fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F Chrome plated stainless steel wire basket for utensils with necessary fixing clips fixed in cupboard etc complete in all respect as specified and as directed by Engineer-in-Charge.

S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified and as directed.

S&F 3 mm thick figured (frosted) glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and directed.

S&F float valve of 20 mm dia PTMT, high pressure with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F in repairs CP curtain rods (medium weight) 20mm dia with fixing with decorative CP brackets, holders side dome etc fixed and design approved by GE complete all as specified and directed.

S&F 100mm long stainless steel handles, oval type complete all as specified and directed.

S&F mild steel Door seal for doors upto 1000mm long and thickness not less than 1mm complete all as specified and directed.

S&F ball bearing runners 45mm telescopic (KTS-20) full extension load capacity 50 Kgs complete all as specified and directed.

M/S CHAUDHARY CONSTRUCTION

M/s Hoti Lal Contractor

Ms Kamal Kant Agarwal

Ahmed constructions