Repair to roof treatment, ceiling, joinery and tilling to certain bldgs of OTM Accn in Zone E-1 and E-2 Area under GE (West) Mathura

Amount

Taking down chowkhats with shutter (without taking off shutters from the frame) area n.exc. 1.50 Sqm each complete all as specified and directed.

Taking down chowkhats with shutter (without taking off shutters from the frame) area exc. 1.50 Sqm but n.exc 4 sqm each complete all as specified and directed.

Taking down shutter only of any description exc 1 sqm but n. exc 2 sqm each complete all as specified and directed.

S&F Pressed steel frame made out of MS Sheet 1.25mm thick for doors of size 125 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including one shop coat of priming complete all as specified and directed. Note:- During fixing of chowkhat, surface shall be make good in plumb with existing finishies like cement plaster simlar wall tiles, floor tiles etc as per site requirement.

S&F Pressed steel frame made out of MS Sheet 1.25mm thick for doors of size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including one shop coat of priming complete all as specified and directed. Note:- During fixing of chowkhat, surface shall be make good in plumb with existing finishies like cement plaster simlar wall tiles, floor tiles etc as per site requirement.

M&L for PCC (1:3:6) type C-0 using 12.5 mm graded stone aggregate as in filling of pressed steel frame complete all as specified and as directed.

S&F 35mm thick plain framed panelled door shutter, factory made (any number of panels) of 2nd class hard wood with lock rail and panels of 9mm thick BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both faces including 2nd class hard wood kail beading 20mm wide tapering from 10mm to 5 mm on one side of shutter & fitted to chowkhats. The size of rail and style shall be as per IS –1003 (Part-I) (wood shall be kiln seasoned and chemically pressure treated) complete all as specified and directed.

S&F for factory made fully glazed/wire gauge (single piece both side ) PVC prelam door shutter 33-35mm thick (style) consisting of frame made out of mild steel tubes of size 19x19mm (19 gauge) in style. Single piece PVC prelaminated coloured PVC sheet 5mm thick to be used to cover styles and rails. PVC sheet strip of 20mm width stuck inside width solvent cement for stiles and plain colour PVC sheet for top rail. Pannel will wire gauge and tighten firmly and fitted as manufacturer instruction including stainless steel wire cloth 0.25mm to 0.36mm nominal dia of wire and average width of aperture 1.4mm to 2mm and aluminium XPM in rhombus shape 1.5mm dia and aperature 18mm (± 1mm), in one piece from top rail to bottom rail as specified and directed Note: All screw shall be self tapping chromium plated”.

S&F 150 mm MS ordinary rat tail rod pattern spring including roller & roller plate complete all as specified and directed.

S&F 100mm long stainless steel Butt hinges fixed complete all as specified and directed.

S&F 200mm stainless steel barrel tower bolts with bright bolt and fixed complete all as specified and directed.

S&F 150mm long stainless steel handles, oval type complete all as specified and directed.

S&F 300mm stainless steel sliding door bolts, bolt type with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F 100mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F mild steel work in hold fasts and similar small articles conforming to Fe-290, Gde-E-165, complete all as specified and directed.

M&L for PCC (1:2:4) type B-1 using 20mm graded stone aggregate in blocks for fixing holdfasts or any other purpose including necessary form work complete all as specified and directed.

S&F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplied and fixed in opening as per specification and drg in SSR Part II 2010 complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile:), with particle board core and 2,4 or 6 raised panel design with 5mm thick Moulded PVC Sheet on the front Face & 2mm Plain colour PVC sheet on back face, fixing in frame at site complete specification & drawing as per SSR.

S&F 35 mm thick 2nd class hard wood glazed & skelton shutters (factory made) open rebated and prepared to receive glass, gauge etc divided into squares with plain chamfered or rounded mitred and rabated sash bars any number, edges of framing plain chamfered or rounded fitted with cut mitred beads for securing glass etc; sizes of members of shutters as specified in SSR Part-I Section- 8 clause 8.24 (a) and fitted to frames/chowkats as in door shutters. (wood shall be kiln seasoned and chemically pressure treated) complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description not otherwise described exc 10 cm width or girth and applying two coats of synthetic enamels paints over a coat of pink primer complete all as specified & directed..

S&F 150mm Anodised aluminium barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F Anodised aluminium 150mm handles, cast type complete all as specified and directed.

S&F for factory made window/ventilator steel rolled framed section of 1 to 1.25mm thick made of galvanized steel, box type hollow , Hollow P Sec incl grill made of 10mm Sq MS bars welded to 12mm x 6mm, MS flat @ 150mm c/c. Grill shall be welded to window frame. The complete unit Ref TD/2013/01 sheet 1/3 to 3/3 shall be a shop coat of zink chromate primer including the following :-. (a) Fly proof shutter shall provided with stainless steel 32mm gauge fly mesh of 304 Gde FE with 144 holes per square mesh. Glazed shutter and fixed glass portion shall be provided with glass of 4mm thick float glass. (b) Window frame shall be fixed to brick wall with by cutting holes and made good dismantled portion in PCC (1:2:4) type B1 four Nos hold fast block for each window/ventilator :- (i) Hold fast 150mm long of 20x3mm MS flat made to shape 4 Nos per window. (ii) Handle of Z Sec 20mm x 25mm, 100mm long – 1 No per leaf. (iii) Mild Steel tower bolt 150mm long - 02 Nos per leaf. (iv) Z Section 20mm x 25mm, 100mm long stopper - 1 No per leaf.

(v) Cleat 55 mm long of hollow square 15 x 20 x 63mm welded to hinge 01 No per leaf. (vi) MS pintle hinges size 75 x 12 mm 02 Nos per leaf. NOTE : During Fixing of Window, Surface shall be make good in plumb with existing finishes like cement plaster complete all as specified and directed.

M&L for applying two coats of synthetic enameled paint over a coat of red oxide primer on new steel surfaces exc. 10 cm girth and width including preparation of new steel surfaces complete all as specified and directed.

Demolition of brick work or stone/boulders masonary, built in cement mortor including all quoins, arches pillars, etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M&L for brickwork with fly ash (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar (1:6).complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM in (1:4) finished fair and even complete all as specified and directed.

M&L for rendering 10 mm thick in CM (1:6) on brick or concrete surface on other than fair faces of brick complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of cement based paint over one coat of cement primer on walls complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of weather proof paint over one coat of primer on walls complete all as specified and directed.

M&L preparation of new plastered surfaces and applying two coats of OBD over one coat of primer on walls complete all as specified and directed.

S&F powder coated aluminum window using 63mmx38mmx1.6mm chowkhats with 48mmx48mmx1.6mm openable section as in shutter including ornamental aluminium grill, 5.5mm thick glass panes of approved make with rubber for fixing glass and including builders hardware such as aluminium handles 100mm-02 Nos, tower bolts 100mm-02Nos, hooks and eye-02 Nos 150mm, butt hinges 100mm 04 Nos etc complete all as specified and directed.

S&F powder coated aluminium anodised door frame and shutter of section as under and providing 5.50mm thick tinted glass with and including each shutter to be provided with aluminium fittings such as aluminum butt hinges 100mm- 03 Nos, Aluminum handles 150mm- 02 Nos, Aluminium tower bolts 150mm- 02 Nos, rubber neopran beadding, glazing clips and one lock four lever with duplicate keys in each opening and 01 No hydraluic door spring etc complete all as specified and directed. Taking down old Aluminium door shutter with chowkhat :- (a) Outer Frame - 100x50x1.20mm (b) Shutter - 90x50x1.20mm (c) Top, middle & Bottom rail 90x50x1.20mm etc

Dismantiling floor, hearth or wall tiling including cement motar bedding ( but not backing ) removing serviceable tiles to store and rubbish off the premishes complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with and including 15mm thick screed bed in cement mortor (1:4) for laying floor finishes. complete all as specified and as directed.

M&L for glazed ceramic coloured tiles in vertical surface 450x300x7-8mm thick set and jointed in neat cement slurry and pointed in coloured cement to match fixed over and including 15mm thick rendering on brick work/concrete surfaces in cement mortar (1:4) for skirting /dado finishes complete all as specified and as directed.

S&F vitreous china squatting pan "ORISSA" pattern size 580mm x 440mm, white with integral foot rest including cast iron 'P' or 'S' trap and connection to trap and to flushing pipe, anti-syphonage pipe,etc. and pan shall be sunk into the floor and embedded in a cushion of lime concrete (1:2) upto 115mm below the top level of pan complete all as specified and directed. .

S&F in repair PVC valve less, symphonic action type, flushing cistern 10 ltr capacity, low level, white/coloured, with inlet, wall valve, float and handle, flush pipe including bracket, complete all as specified and directed.

S&F in repair vitreous china wash basin, white, flat back, size 550 X 400mm including waste and CI brackets of suitable but excluding tapes, chain and plug etc, complete all as specified and directed.

S&F in repair of PVC connection pipe 15 mm size with nuts, washers of length 600 mm pipe complete all as specified and directed.

S&F in repair vitreous china wash down, water closet pan (pedrestal pattern), white including fixing bolts and connection to flush pipe and drain out going pipe and closet seat cover black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device ,CP Jet including PVC Connection etc complete all as specified and directed.

S&F in repair 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F in repair 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110mm PVC (SWR) bends any radius complete all as specified and directed.

S&F in repair 110mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F in repair 75mm PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair 75mm PVC (SWR) multi floor trap with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair 110mm PVC (SWR) junction double, (double T), equal or unequal complete all as specified and directed.

S&F 75mm PVC (SWR) bends any radius complete all as specified and directed.

S&F stack clamps made out of 50mm by 5mm flat iron including bolts and nuts and securing ends of stays to wall or roof for 110mm bore pipe complete all as specified & directed.

S&F in repair stack clamps made out of 50mm by 5mm flat iron including bolts and nuts and securing ends of stays to wall or roof for 75mm bore pipe complete all as specified & directed.

Taking down steel tubing and connections 15mm bore tube complete all as specified and directed.

Taking down steel tubing and connections 20mm bore tube complete all as specified and directed.

S&F GI tubes medium grade, with all fittings and fixed complete to wall and ceiling/floor 15mm bore complete all as specified and directed.

S&F GI tubes medium grade, with all fittings and fixed complete to wall and ceiling/floor 20mm bore complete all as specified and directed.

Dismantling of ceiling boards of any type and any thickness including cover fillets complete all as specified and directed.

S&F suspended false ceiling system using Chicago metallic (E grid) exposed suspended system, grid section size 600mm X 600mm comprising of GI powder coated Main Runner of dimensions 39 mm X 24mm X 0.8mm thick (thickness comprising of GI/0.4+ PPPCGS/0.3mm & weight of runner 1.35 kg for 3600mm length) Cross Tee of dimensions 29mm X24mmX0.8mm thick and thick wall angle 22.2mmX22.2mmX 0.65 mm thick ( thickness comprising of GI/0.35+ PPPCGS/0.3mm & weight of angle 0.70 kg for 3050mm length)with and including 4mm thick Gypsum board to be placed in the grid system duly suspended with 2mm dia GI bar hangers fixed with steel dash through fasteners from purlins of the roof with provn of light fixture if directed complete all as specified and directed.

Wornout existing treatment from sunken portion of WC /Bath/Kitchen/Passage area n exc 2.5 Sqm each including taking down floor tiles, plaster, lime/cement concrete, WC trap complete empty of existing sunk. (Taking down of plumbing & sanitary fixing & fixture shall be measured under relevant items).

M&L for treatment of sunken floor slab cosisting of the following specification as under: (i) Cleaning the sunken/lowered portion of RCC slab surfaces(including vertical total depth with skirting height) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely. (ii) PCC (1:2:4) type B0 40mm thick (average) using 12.5mm graded stone aggregate as in padding to acheive proper slope towards spout . (iii) Rendering of uneven surfaces with 10mm thick in CM (1:4) mixed with liquid water proofing compound (Liquid water proofing shall be measured and paid separately) and finish surface even and fair . (iv) All junctions points of side wall where CI/GI pipes are passing through wall shall be sealed with epoxy putty. (v) After drying putty, wash the slab and sides of sunken portion with water make it clear and clean. (vi) At the end sunken portion shall be checked for dampeness and seepage/leekage. If dampness/seepage is noticed nozzles shall be fixed and grounting carried out complete.

(vii) Plaster the bottom and sides up to bottom of the skirting with minimum 20mm thick in CM (1:4) mixed with liquid water proofing including rounding of corners and junctions sloping towards spout complete.(Liquid water proofing shall be measured and paid separately) (viii) Applying two coats of polymer modified cementious water proof coating as per manufacturers instructions to bottom and vertical sides up to finished floor level +100mm height . The thickness of two layer shall be 1mm and the second layer is still sticky, coarse sand spray shall be carried out for the vertical and bottom surfaces of the sunken portion. Note: Test of water proofed area (ponding test) by filling water for at least 72 Hours and tested for leakage/seepage to the entire satisfaction of GE. Test shall be done in presense of rep of PMG and record for each sunken slab shall be maintained. The treatment shall be carried out by authoried applicators. cost of testing shall be included in the quoted rate.

M&L for rendering dubbing coat over irregular surfaces of chajjas roof projections/ceiling/facia etc average 15mm thick in CM (1:4) over cement slurry coat @ 3Kg/Sqm making the surface even followed by 5mm thick rendering in CM (1:3) furnished even & smooth including making of drip course as required complete including roughening surface of old concrete by picking sweeping clean and washing with water complete all as specified and directed.

Supply only Liquid water proofing compound of approved make complete all as specified and directed.

S&F GI tubes medium grade, laid on sunken floor as on spout pipe 50mm bore complete all as specified and directed.

M&L for PCC (1:5:10) type E2 using 40mm grade stone aggregate in sunken portion complete all as specified and directed.

M&L for cutting holes in brick walls exceeding half brick wall and n.exc one brick wall, built in cement mortar for inserting spout and making good dismantled portion in cement mortar (1:3) or cement concrete (1:2:4) Type B-1 as required complete all as specified and directed.

Dismantling brick/concrete tiles any size etc including existing roof treatment of any thickness complete all as specified and directed.

M&L for PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate as in padding over roof finished and laid to required slope complete all as specified and as directed.

M&L for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed.

M&L for brushing neat cement slurry with 3.0 kg of cement per sq. metre complete all as specified and directed.

M&L for preparing cement concrete surface and providing 10mm thick modified plaster in CM (1:4) mixed with polymer in ratio 1:10 (1 part of polymer and 10 part of cement) and applying a coat of epoxy primer with resin and hardner with water dilution as per manufacturers instructions including applying two coats of polyethelene liquid membrane each coat not less than 500 micron thick UV stable having SRI value equal or grater than 105 with consumption of 0.61 Kg/Sqm (each coat) and second coat should be applied once the first coat is fully dried complete all as specified and directed.

S&F precast hydraulically pressed PCC tiles of size 25cm x 25cm x 20mm thick laid over and including screed bed 15mm thick in CM (1:4) set and jointed in neat cement slurry and pointed in CM (1:3) mixed with WPC of approved make in screed bed and pointing on roof complete all as specified and directed.

Dismantling asbestos cement/GI/PGI corrugated or semi corrugated sheets in roof covering including ridge complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strenght of 550 Mpa as in roof covering / cladding to wall fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strenght of 550 Mpa as in roof covering / clading to wall fixed with self tapping screws complete all as specified and directed.

S&F 6mm thick asbestos cement, corrugated or semi-corrugated sheets fixed with L-type or J-type or cranked hook bolts and washer in roofs, walls etc complete all as specified and directed.

S&F 6mm thick Asbestos cement two piece adjustable serrated ridge fixed with L-type or J-type or cranked hook bolts and washer for corrugated or semi corrugated sheets complete all as specified and as directed.

S&F sheet glass ordinary quality 4mm thick and glazing with oil putty or wdn beads in shape n.exc 0.50 Sqm in each pane including hacking out glass complete all as specified and directed.

Karman Infra Projects

M/s Shrangi Rishi Construction

M/S MRS BHASKAR

M/s Hoti Lal Contractor