ADDN/ALTN TO CERTAIN SMQ IN SECTOR 31 AND 47 AT CHANDIGARH UNDER GE (AF) CHANDIGARH

Amount

Note :The unit rate quoted by the tenderer under Col No (13) of Sch `A’ (BOQ) unless specifically mentioned otherwise such as labour only/fixing only, for all items of works shall be deemed to be including cost of all materials, labour, tools and plants, testing and commissioning of work in position complete as required for entire completion of work.

Plain cement concrete ,25 mm average thickness (1:2:4) type B-0, using 12.5 mm graded mechanically crushed stone aggregates as in levelling course finished even & rough without using extra cement in and including demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness (below or above ground level) and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge.

Glass dividing strips, 3 mm thick and 38mm wide, as in floors fixed in position , complete all as specified and directed by Engineer-in-Charge.

Plain cement concrete (1:2:4) type B-1 using 20 mm graded mechanically crushed stone aggregates as in mud stop ,sides of intetlocking paver block and the like including rounded or chamfered on edges including necessary form work and finished the surfaces even and smooth (without using extra cement) in and including demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness (below or above ground level) and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge.

Brick work with sub-class `B' bricks Fly ash bricks (bricks shall be burnt clay fly ash building bricks as per IS- 13757), straight or curved on plan exceeding 6 M mean radius built in cement sand mortar 1:6 in and including demolition of brickwork or stone boulder masonary built in cement mortar including all quoins, arches, pillars etc for area where servicable bricks retrived and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge.

Use & waste of form work to soffits of suspended slab of concrete such as roof slabs, floor slabs, cover slab, shelve, landings and similar works n.exc 200 mm thick (horizontal or sloping); with rough finished surfaces of concrete, complete all as specified and directed by the Engineer in Charge.

Mild steel TMT bars 10mm dia and over as in reinforcement cut to length , bent to shape required, including cranking, bending spirally for hooping ends for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.90mm dia in and including demolition of reinforced cement concrete of any description & in any position and removal of rubbish outside MoD land, complete all as specified and directed by the Engineer in Charge.

Reinforced Cement concrete 1:2:4 type B-1, using 20 mm graded mechanically crushed stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the likes in and including demolition of reinforced cement concrete of any description & in any position and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge. Note: Steel reinforcement shall be measured and paid for separetely.

First quality glazed ceramic coloured tiles of 450x300x7-8 mm thick laid on vertical surfaces such as skirting, dados and risers to steps etc laid over and including 10mm thick cement plaster in CM (1:4) set and jointed in neat cement paste of honey like consistancy and pointed in white or coloured cement to match the shade of tiles in and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge. Note : Design, pattern and colour of tiles will be as approved by GE.

First quality, Non skid ceramic coloured tiles, 7 to 8 mm thick joint free (square/ rectangular) area of each tile exceeding 0.11 Sq.m but not exceeding 0.18 Sq.m, laid in floors with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed of cement mortar (1:6) including pointing in white or coloured cement to match the shade of tiles in and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge. Note :- Design, pattern and colour of tiles will be as approved by GE.

First quality, Non skid ceramic coloured tiles, 7 to 8 mm thick joint free (square/ rectangular) area of each tile exceeding 0.18 Sq.m but not exceeding 0.36 Sq.m, laid in floors with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed of cement mortar (1:6) including pointing in white or coloured cement to match the shade of tiles in and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge. Note :- Design, pattern and colour of tiles will be as approved by GE.

First quality, Non skid ceramic coloured tiles, 7 to 8 mm thick joint free (square/ rectangular) area of each tile exceeding 0.18 Sq.m but not exceeding 0.36 Sq.m, las in skirting, dados and risers to steps etc laid over and including 10mm thick cement plaster in CM (1:4) set and jointed in neat cement paste of honey like consistancy and pointed in white or coloured cement with pigment to match the shade of tiles in and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge. Note :- Design, pattern and colour of tiles will be as approved by GE.

Demolition of stone slab and tiles of any description or thickness in floors, aprons etc, laid bedded and pointed in cement mortar and removal of rubbish outside MoD land ,complete all as specified and as directed by Engineer -in-Charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushing neat cement slurry with 3.0kg of cement per sq. metre ,complete all as specified and as directed by Engineer -in-Charge.

Granite (of any type ) 16-18 mm thick, work (table rubbed and polished) fine grained 'Z' black/red in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including screed bed of 15 mm thick in CM 1:4 ,complete all as specified and as directed by Engineer -in-Charge.

Taking down cement plaster on brick walls & concrete surfaces & the like including raking out joints, hacking for key, scrubbing down with water etc., any description, and removal of rubbish outside MoD land , complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick plaster on brick work or concrete surfaces in cement mortar (1:6) , finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement , complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered or unplastered surfaces of wall and applying three coats of white washing , complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white washing , complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer over and including 1mm thick wall care putty to smoothening the surface by using sand paper , complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint , complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment of internal surfaces of walls including brooming down or steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc; washing, rubbing down and stopping of surfaces using and paper and applying two coats of oil bound distemper over a coat of alkali resistant primer over and including 1mm thick wall care putty interior grade to smoothening the surface by using sand paper

Preparation of old surfaces of wall including brooming down or steel wire brushing, scraping down smoke soot, moulds, mooss and efflorescent salts and trading oil and greasy spots etc and filling the cracks/holes with cement wall care putty and applying one coat of white wash, complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment of old plastered /unplastered surfaces of walls /ceiling by mechanically boomer and preparing plastered or unplastered old surfaces of walls including brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and filling the cracks/holes with wall care putty to rubbing down and stoping of surfaces using sand paper and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistance as per IS 15489: 2004, alkali & fungal resistant, dirt resistant exterior paint of required shade as approved with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm , complete all as specified and directed by Engineer-in-Charge.

Taking down Chowkhats with shutters without taking of shutter from the frame of any description not exceeding 1.50 Sq. m each, and making good the disturbed surface with PCC 1:2:4 type B-0 and CM 1:4 & finished with similar specification as exists, complete all as specified and as directed by the Engineer-in-Charge.

Taking down Chowkhats with shutters without taking of shutter from the frame of any description exceeding 1.50 Sq. m but not exceeding 4.00 Sq. m each, and making good the disturbed surface with PCC 1:2:4 type B-0 and CM 1:4 & finished with similar specification as exists, complete all as specified and as directed by the Engineer-in-Charge.

35 mm thick (Batten thickness) Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive wire cloth, glass etc. divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, wire cloth etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats,complete all as specified and directed by the Engineer in Charge.

35 mm thick factory made Flush shutters ,solid core construction with block board core and plywood face panels commercial type on both sides, duly provided with 6mm thick Teakwood leeping on edges alround, fitted to chowkats, , complete all as specified and as directed by Engineer-in- Charge.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length , complete all as specified and directed by the Engineer in Charge. Note:M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately.

Factory made single extruded WPC (Wood Polymer Composite) solid plain door shutter of size 30 MM thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisturproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws ,complete all as specified and directed by Engineer-in- Charge. Note:M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm in cupboard comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length, complete all as specified and directed by the Engineer in Charge. Note:M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately.

Factory made single extruded WPC (Wood Polymer Composite) solid plain flush type as in shutter or exposed member of cupboard shutter of 18mm thick with Balancing on one face and wooden grain pattern lamonation on exposed surface with and including 18 mm wide 0.8 to 1 mm thick PVC leaping on exposed face to match with shade of shutter fixed with suitable solvent comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant, in and including dismantling of old board/Cup board shutter any description fixed in any postion with nails ,complete all as specified and directed by Engineer-in- Charge.

Factory made single extruded WPC (Wood Polymer Composite) solid plain Kitchen cabinet as shutter, shelves and door shutter of size 18mm thick Lamination/Balancing on both side comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisturproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter with and including 18 mm wide 0.8 to 1 mm thick PVC leaping on exposed face to match with shade of shutter fixed with suitable solvent and fixing with WPC beadind 20 mm wide 18 mm thick fixed to wall with necessary full body threaded star headed counter sunk S.S screws and PVC rawl plug or PVC solvent , complete all as specified and directed by the Engineer in Charge.

Factory made single extruded WPC (Wood Polymer Composite) solid plain flush type as in kitchen cabinet structure/Shutter or exposed member of cabinet structure of 18mm thick with Balancing on one face and wooden grain pattern lamonation on exposed surface with and including 18 mm wide 0.8 to 1 mm thick PVC leaping on exposed face to match with shade of shutter fixed with suitable solvent comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant , complete all as specified and directed by the Engineer in Charge.

Factory made single extruded WPC (Wood Polymer Composite) solid plain flush type as in back member of cabinet structure of 06 mm thick with Balancing on one side comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant , complete all as specified and directed by the Engineer in Charge.

Factory made box type steel window with pintle hinges and two nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer , complete all as specified and shown on Drawing No CEAF/STD-184-2012 Sheets 1/3 & 3/3 and as directed by the Engineer in Charge.

Factory made made box type steel window with pintle hinges and two Nos 150mm mild steel tower bolts to each shutter, steel handle and without glazing bars, including flat iron 12 x 3 mm for securing wire mesh, dovetailed or welded and with one shop coat of zinc chromate primer complete , complete all as specified and shown on Drawing No CEAF/STD-185-2012 Sheets 1/2 & 2/2 and as directed by the Engineer in Charge.

Factory made box type steel ventilator fixed type, dovetailed or welded and with one shop coat of zinc chromate primer, complete all as specified and shown on Drawing No CEAF/STD-186-2012 Sheets 1/1 and as directed by the Engineer in Charge.

Factory made made box type steel ventilator with glazed shutter or gauzed shutter with glazing bars or flat iron 12 x 3mm dovetailed or welded for fixing wire mesh/glass and with one shop coat of zinc chromate primer , complete all as specified and shown on Drawing No CEAF/STD-186-2012 Sheets 1/1 and as directed by the Engineer in Charge.

Butt hinges 125 mm size ,heavy duty, stainless steel hinges fixed with stainless steel screw for 30 mm thick door shutter,complete all as specified and directed by the Engineer in Charge.

75 mm size 15-18mm wide flap of heavy duty stainless steel hinges fixed with stainless steel screw ,complete all as specified and directed by the Engineer in Charge.

Barrel tower bolts aluminum anodizes of extuded section and fixed of 150 mm long size (length of bolt) , complete all as specified and directed by Engineer-in-Charge

50 mm size stainless steel handles medium duty and fixed , complete all as specified and directed by Engineer-in-Charge

Stainless steel soft close hydraullic clip concealed cabinet hinges fixed with stainless steel screw , complete all as specified and directed by Engineer-in-Charge

120 mm size stainless steel handles medium duty and fixed , complete all as specified and directed by Engineer-in-Charge

Handles 'D' type of size 125 mm ,extruded aluminium alloy , fabricated type anodized ,complete all as specified and directed by Engineer-in- Charge.

Aluminum alloy, anodized, sliding door bolt with hasp staple ( bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed length of bolt 250 mm, bolts not less than 12mm dia with and including a minimum of 6 bolts not,four on bolt plate and two on staple plate complete (ISI marked ) , complete all as specified and directed by Engineer-in-Charge

Continuous (Piano) hinges, width of flaps (when open ) 30mm, stainless steel bright finish or electro galvanised, ISI Marked ,complete all as specified and directed by Engineer-in- Charge.

Hasp & staple of 100mm size ,safety type aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws ,complete all as specified and directed by Engineer-in- Charge.

Stainless steel Magnetic door catcher Magnet of size 50x15mm fixed with Gypsum screw on shelf/sides wall and shutter,complete all as specified and directed by Engineer-in- Charge.

50mm dia polished hard wood knobs fixed with thread screw and nut ,complete all as specified and directed by Engineer-in- Charge.

300mm long ordinary rat tail rod pattern Mild steel door springs including roller and roller plate with steel screws or with welding as required at site , complete all as specified and directed by Engineer-in-Charge.

Door seal 50mm wide and 1 m in lenth built in aluminium black plate with nylon brush fixed with screws fixed as in repairs, complete all as specified and directed by Engineer-in-Charge.

Sheet glass 4 mm thick, ordinary quality and glazing with oil putty or wooden bead in squares exceeding 0.5 Sq. m in each pane ,complete all as specified and directed by Engineer-in- Charge.

Figured glass 3 mm thick, pin headed tyoe and glazing with oil putty or wooden bead in squares not exceeding 0.5 Sq. m in each pane,including fixing with glass pins to hold glass in position ,complete all as specified and directed by Engineer-in- Charge.

Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed to steel frames with stainless steel tacks, or stainless steel wire staples, or fixed to wooden frame with first class hard wood bead, ,complete all as specified and directed by Engineer-in- Charge.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor of overall length of cover plate 140mm , complete all as specified and directed by Engineer-in-Charge.

Framed work as in doors/Chowkhats or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete ( Fe-290,Gde-E-165) in and including dismantling structural steel work including doors, gates/grill but excluding framed truss etc., complete all as specified and directed by the Engineer-in-Charge.

Cutting holes in brick walls built in cement or cement lime mortar for inserting hold fasts, etc and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1, cutting exceeding half brick but not exceeding one brick complete.,complete all as specified and directed by Engineer-in- Charge.

Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 ,complete all as specified and directed by Engineer-in- Charge.

M S work as Framed works such as grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes,framed guard bars barred iron doors ladders, framed balusters walk ways railing, framed work of water tanks, framed and hung as gates including pintle hinges, stops, hand made sliding sliding bolts etc ,drilling bolting or reveting etc and similar work conforming Fe-290 Gde E-165 ,complete all as specified and directed by Engineer-in- Charge.

Preparation of new or previously untreated wooden surfaces of any description , not otherwise described over 10 cm width or girth and applying two coats of synthetic enamells paint over one coat of pink primer ,complete all as specified and directed by the Engineer in Charge.

Preparation of new or previously untreated steel surfaces of any description , not otherwise described over 10 cm width or girth and applying two coats of synthetic enamells paint ,complete all as specified and directed by the Engineer in Charge.

Cutting chases, pinning in making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing and making good, cutting not exceeding 10cm girth, and removal of rubbbish outside MOD land,,complete all as specified and directed by Engineer-in- Charge.

Steel water tubing, 15 mm bore medium grade ISI Marked, galvanized with all fittings and fixed complete to walls, ceiling or laid in floors in and including taking up or down existing unservicable tubing and connections, cleaning for re fixing or removal to store, complete all as specified and directed by Engineer-in-Charge. Note: Fittings & specials as required shall be provided by the contractor. Contractor's rate shall be deemed to include the cost of fittings provided.

Steel water tubing, 20 mm bore medium grade ISI Marked , galvanized with all fittings and fixed complete to walls, ceiling or laid in floors in and including taking up or down existing unservicable tubing and connections, cleaning for re fixing or removal to store, complete all as specified and directed by Engineer-in-Charge. Note: Fittings & specials as required shall be provided by the contractor. Contractor's rate shall be deemed to include the cost of fittings provided.

Rotational moulded PVC, tripple layered, water storage tanks of capacity 500 litre (cylindrical vertical with closed top), ISI Marked, hoisted and fixed in position, with & including all fittings such as GI tank nipple etc. including Ball valve high pressure of PTMT with epoxy coated aluminium door and highdensity plastic ball screwed for 20mm dia iron pipe and fixed (minimum wieght 20mm 210gms )in and including dismantling PVC water tanks exc 251 ltr but n. exc 500 ltr capacity by disconnecting existing water connection and removal from site ,complete all as specified and directed by Engineer-in- Charge.

Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed for 20 mm bore dia fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Stop valve /Angle cock, 15 mm bore fancy type chromium plated cast copper alloy, screwed down,high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions fixed as in repair , complete all as specified and directed by Engineer-in-Charge.

Bib cock long body with flange,15 mm bore fancy type cast copper alloy Chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fixed as in repair , complete all as specified and directed by Engineer-in-Charge.

Pillar cock, long neck fancy type cast copper alloy , with capstan heads, chromium plated , screwed down for 15 mm bore pipe,high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Wall mixer with L bend (provision for over head shower), cast copper alloy, chromium plated for mixing hot and cold water, screwed down for 15mm bore iron pipe and fixed as in repair, complete all as specified and directed by Engineer-in-Charge.

Wash basins ,vitreous china, white,rectangular type of size 550x400mm including brackets and cutting for and pinning in ends of brackets or erecting stand 32mm dia Waste fittings, brass, chromium plated for glazed basins with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed inluding new brackets fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

Vitreous China squating pan, 'Orissa' pattern, size 580x440mm white, with integral foot rests, including 100mm cast iron 'P' or 'S' trap and 100mm cast iron sanitary connection socket to fit WC outlet including connection to trap, to flushing pipe, anti-syphonage pipe etc. complete including making good to floor fixed as in repair , complete all as specified and directed by the Engineer in -Charge. Note :- Qty and Rates are inclusive of for both P type and S type Traps as on actual required basis on ground

Vitreous China wash down water closet pan (pedestal pattern), white with plastic seat cover (excluding fixing bolts, flushing cistern and flush pipe) including connection to trap,and to flushing pipe, anti-syphonage pipe,etc including 100mm cast iron 'P' or 'S' trap complete including making good to floor with plastic water closet seat cover good quality in white colour with flat bottom and cover and mild steel chromium plated or aluminium hinging devices, connected to drains outlet fixed as in repair, complete all as specified and directed by the Engineer in -Charge. Note :- Qty and Rates are inclusive of for both P type and S type Traps as on actual required basis on ground

PVC valveless , syphonic action type flushing cisterns 10 ltrs capacity , low level , white, with inlet ball valves , float and handle including brackets and pvc flush pipe 32 mm dia for low level fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

PVC connections 15mm size with PTMT nuts of length 600 mm fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

PVC waste pipe flexible for Sink/ WHB of 32mm size fixed as in repair , complete all as specified and directed by the Engineer in -Charge.

PVC cabinet mirror of size 400mmx500mm fixed as in repair,complete all as specified and directed by Engineer-in- Charge. Note : Colour and pattern of cabinet shall be approved by Garrision Engineer.

Soap dish brass, chromium plated fancy type fixed to plugs with chromium plated brass screws. fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Rectangular Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed with PVC rawl plugs and wooden screws fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Corner glass shelf of radius 300 mm including 02 Nos. metallic holding brackets, railing etc. fixed with PVC rawl plugs and wooden screws fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

CP grating 125 mm dia/hinged of brass and fixing with cement mortar 1:3 with/without holes as required fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Towel rail 600 mm long, 20 mm dia, ‘D’ type, brass chromium plated, fixed to walls with screws and plastic cleats fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Drapery rod of Stainless steel 25mm dia, fancy type, any shade, in and including set of fixing brackets, fixed to wall with stainless steel finols/finnels, connected accessaries, rubber packing, required screws and PVC rawal plugs as required fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to wall including holding holder /clamps and making good the mouth of rain water pipe in and including taking down eaves gutter and rainwater pipes any dia (any size or pattern), including all fittings ,complete all as specified and directed by Engineer-in- Charge.

PVC (SWR) bends /Tee, shoe any radius, fixed with solvent cement in any position as per site requirement any radius 100mm bore fixed with solvent cement in any position as per site requirement fixed as in repair , complete all as specified and directed by Engineer-in-Charge.

Cast iron soil, waste and vent pipe ,75 mm bore of spun cast pipes in any length with or without ears, with cement joints laid in trenches or in floor in and including dismantling of cast iron work of any description,complete all as specified and directed by Engineer-in- Charge.

Cast iron soil, waste and vent pipe ,100 mm bore of spun cast pipes in any length with or without ears, with cement joints laid in trenches or in floor in and including dismantling of cast iron work of any description,complete all as specified and directed by Engineer-in- Charge.

Cast iron soil, waste and vent pipe ,75 mm bore of spun pipe in any length with or without ears, with cement joints fixed in wall including clamp holder batsin and including dismantling of cast iron work of any description,complete all as specified and directed by Engineer-in- Charge.

Cast iron soil, waste and vent pipe ,100 mm bore of spun pipe in any length with or without ears, with cement joints fixed in wall including clamp holder batsin and including dismantling of cast iron work of any description,complete all as specified and directed by Engineer-in- Charge.

Cast iron soil, waste and vent pipe ,50 mm bore of spun pipe in any length with or without ears, with cement joints fixed in wall including clamp holder batsin and including dismantling of cast iron work of any description,complete all as specified and directed by Engineer-in- Charge.

Cast iron cowel 50mm dia bore, ISI markedincluding jointing with solventin any postion as per site requirment fixed as in repairs,complete all as specified and directed by Engineer-in- Charge.

Cast iron (spun) bends 75mm dia bore, diminishing pieces or tapers ISI marked fixed as in repair (larger bore measured) with oval access door,complete all as specified and directed by Engineer-in- Charge.

Cast iron (spun) Bends (any radius), with duck's foot or heel rest 75 mm bore fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Cast iron (spun) Bends (any radius), with duck's foot or heel rest 100 mm bore fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Cast iron (spun) branch pieces 75mm dia bore, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches ,reducers fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Cast iron (spun) branch pieces 100mm dia bore, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches ,reducers fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Cast iron (spun) floor trap, 75mm dia of out let, ISI marked, with stain less Steel grating, excluding jointing to waste pipe in Plain cement concrete (1:2:4) type B-1 fixed as in repair,complete all as specified and directed by Engineer-in- Charge.

Cast iron (Spun) Sockets (double) collars fixed as in repair ,complete all as specified and directed by Engineer-in- Charge.

Preparation of newly plastered/RCC surfaces, making the surface completely dry and applying a coat of bitumen primer, having density in range of 0.87 to 0.89 kg/litre at 25 degree centigrade and viscosity of 70 to 160 CPS, manufactured by same manufacturer @ 0.4 ltr/sqm shall be applied and after drying of primer for 24 hours apply APP modified prefabricated water proofing membrane with non - woven polyster reinforcement, 3mm thick superior multipolymeric, weighing not less than 3.00 kg/sqm with properties of high penetration and centre core consisting of 90 micron high molecular high density polyetylene (MHHDPE) film consisting of five layers laid with torching application to the surface comeplete and sealing the side as well as end laps with torch (overlaps should not be less than 10cm in longitudinal direction and 15cm in traverse direction and shall be bonded with bitumen primer and levelled by heating the overlaps with brutane torch) , complete all as specified and directed by Engineer-in-Charge.

Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner ,complete all as specified and directed by Engineer-in- Charge.

Uprooting completely natural vegetation/ plants, stems of trees (upto 30cm girth) grown up on walls, parapets or in roof or any part of building upto 10 metre (Ground +2 storey) and making good the damaged/ disturbed portion and filling holes in cement mortar (1:3) or PCC (1:2:4) type B-0 using graded crushed stone aggregate to match with the existing surface , complete all as specified and directed by Engineer-in-Charge.

Plain Cement concrete type B-0, 1:2:4 by using 12.5 mm graded mechanically crushed stone aggregate as in sunken portion or similar items as in filling in and including demolition of lime concrete/lean concrete/brick bats from sunken portion exc. 15cm thickness (above ground level) in and including removing of debris away from site to a designated point fixed by local administration out side of MOD land , complete all as specified and directed by the Engineer in Charge .

Broken brick or boulders aggregate not exc 63mm deposited spread and levelled in layers not exc 15mm thick watered and rammed to a true surface in sunken portion or similar items as in filling in and including demolition of lime concrete/lean concrete/brick bats from sunken portion exc. 15cm thickness (above ground level) in and including removing of debris away from site to a designated point fixed by local administration out side of MOD land , complete all as specified and directed by the Engineer in Charge .

Steel water tubing, 50 mm bore medium grade ISI Marked , galvanized as in Spout for sunken floor, fixed as in wall with inside end fixed with wire netting and external end bevelled edge at 45 degree, complete all as specified and directed by Engineer-in-Charge.

Applying two coats of two component elastomeric acrylic polymer modified cementtitious waterproofing coat ng, smartcare Ultra block 2K or equivalent, having 215% elongation as per ASTMD-2370, resisting 5 bars hyrostatic pressure as per DIN 1048, Crack briding upto 3.50mm as per EN 1062-7 and sprinkling dry fine sand over wet second coating compelete, as per manufactures specifications ,complete all as specified and directed by Engineer-in- Charge. Note : Unless otherwise recommended by manufacturer, the mixing ratio of the components shall be 6 part of powder and 4 parts of liquid without any water addition in the mixing etc.

Welding in repair exc 2.5 cm but n exc 5.00 cm in length thickness of metal to be welded n.exc 6mm, including cleaning, preparing the surfaces and holding the member in true position for maintenance of steel items such as gates, grills, doors window etc. ,complete all as specified and directed by Engineer-in- Charge.

Mild steel, plain, black of sheet of 1 mm thick iheet in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required , complete all as specified and directed by Engineer-in-Charge.

Wall mounted Kitchen Utensils dish rack stainless steel (31x10x30 inches) as approved by GE, complete all as specified and directed by Engineer-in-Charge.

Taking down carefully aluminium/ copper point wiring (light/ fan/ socket/ power) complete (fittings such as switches, sockets, ceiling roses pendants, regulators, sockets, light fitting etc. to be measured separately), removing materials to store for keeping in safe custody or for taking credit as per Schedule of credit including making good disturbed surfaces of walls, floors etc. , complete all as specified and directed by Engineer-in-Charge.

Point wiring for one light point/Fan point controlled by one switch one way drawn through and including non metalic rigid PVC conduit medium duty of 20 mm dia or higher concealed type with all strandard fittings such as Tee junction, bends etc ,usingusing FRLSH PVC unsheathed multistrand copper conductor cable of 1.5 sqmm single core including 3 mm thick plastic laminated sheet cover over PVC / wooden Box for earth continuity insulated PVC unsheathed(green colour) 1.5 sqmm copper earth wire connected to common earth dolly ,complete all as specified and as directed by Engineer-in- Charge. Note : Wiring shall be done by using proper colour coding.

All as per srl item No. 131 here-in-before but for 05 Amp socket outlet on independent board, with cables 1.5 sqmm., complete all as specified and directed by Engineer-in-Charge. Note : Wiring shall be done by using proper colour coding.

All as per srl item No. 131 here-in-before but for One 3 pin socket outlet 5 amps on the same board with other switches, with cables 1.5 sqmm., complete all as specified and directed by Engineer-in-Charge. Note Wiring shall be done by using proper colour coding.

Point wiring for one light point controlled by two switchs two way drawn through and including non metalic rigid PVC conduit medium duty of 20 mm dia or higher concealed type with all strandard fittings such as Tee junction, bends etc ,using FRLSH PVC unsheathed multistrand copper conductor cable of 1.5 sqmm single core including 3 mm thick plastic laminated sheet cover over PVC / wooden Box for earth continuity insulated PVC unsheathed(green colour) 1.5 sqmm copper earth wire connected to common earth dolly ,complete all as specified and as directed by Engineer-in- Charge. Note : Wiring shall be done by using proper colour coding.

Point wiring for one Bell point controlled by one switch one way drawn through and including non metalic rigid PVC conduit medium duty of 20 mm dia or higher concealed type with all strandard fittings such as Tee junction, bends etc ,using FRLSH PVC unsheathed multistrand copper conductor cable of 1.5 sqmm single core including 3 mm thick plastic laminated sheet cover over PVC / wooden Box for earth continuity insulated PVC unsheathed(green colour) 1.5 sqmm copper earth wire connected to common earth dolly ,complete all as specified and as directed by Engineer-in- Charge. Note : Wiring shall be done by using proper colour coding.

Point wiring for 15 Amps socket point controlled by one, one way switch using drawn through and including non metalic rigid PVC conduit medium duty of of 20 mm dia or higher with all strandard fittings such as Tee junction, bends etc ,using FRLSH PVC unsheathed multistrand copper conductor cable of 2.5 sqmm single core a including 3 mm thick plastic laminated sheet cover over PVC / wooden Box for earth continuity insulated PVC unsheathed(green colour) 1.5 sqmm copper earth wire connected to common earth dolly ,complete all as specified and as directed by Engineer-in- Charge. Note : Wiring shall be done by using proper colour coding.

Switch piano, flush type single pole, one way 6 Amp , complete all as specified and directed by Engineer-in-Charge.

Switch piano, flush type single pole, one way 16 Amp , complete all as specified and directed by Engineer-in-Charge.

Socket outlet 2 in1, flush type 3 pin,6 Amp mult ipurpose, complete all as specified and directed by Engineer-in-Charge.

Socket outlet 2 in1, flush type 3 pin,6 and 16 Amp mult ipurpose, complete all as specified and directed by Engineer-in-Charge.

Switch piano, flush type single pole, two way 6 Amp ,complete all as specified and as directed by Engineer-in- Charge.

Swithc Bell push flush type 5 Amp,complete all as specified and as directed by Engineer-in- Charge.

Ceiling Rose, surface bakalite,65x50 mm two to three terminala , complete all as specified and directed by Engineer-in-Charge.

Ceiling fan regulator step type electronic for 1200/1400 mmseep ceiling fan watt ,2 module for 1200/1400 mm sweep ceiling fan and connecting up ,complete all as specified and directed by Engineer-in- Charge.

Buzzer, Ding Dong AC. 230 volts,single pole ,complete all as specified and directed by Engineer-in- Charge.

MCB SP, 6 to 32 Amps, ,240 Volts ,10 KA 'B' curve type to be housed in DBs of Proper and suitable size cable lugs to be fixed with MCBs fixed as in replacment ,complete all as specified and directed by Engineer-in- Charge.

MCB SPN, 40 to 63 Amps, ,240 Volts ,10 KA 'C' curve type to be housed in DBs of Proper and suitable size cable lugs to be fixed with MCBs fixed as in replacment ,complete all as specified and directed by Engineer-in- Charge.

Distribution box Double door type , SPN 12 way,with 200 amps rated bus bar, 240 Volts 50 HZ for MCBs, grouted flush to walls complete with IP 65 and metal double door ,epoxy powder coated fixed as in replacment ,complete all as specified and directed by Engineer-in- Charge.

Sheet metal enclosure factory made single pole & neutral with a two pin & earth plug and socket etc complete with provision for one single pole 'B' series MCB 20 Amps 240 volts ,complete all as specified and directed by Engineer-in- Charge.

LED Lights fittings 4ft, 1x18watt 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose, complete all as specified and directed by Engineer-in-Charge.

LED light fitting 1x9W/1x10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed by Engineer-in-Charge.

LED light fitting mirror type with high out put diffuser 2ft, 10watt 220v AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size, complete all as specified and directed by Engineer-in-Charge.

Wall mounted fittings with ABS housing and clear polycarbonate cover including retrofit LED bulb 7/9 watt and connecting up with three core flexible copper conductor cable of 0.5 sqmm size from ceiling rose, complete all as specified and directed by Engineer-in-Charge.

Exhaust fan, steel body AC single phase 230v of size 300mm sweep 50 HZ ,1200RPM copper windening with blades, frames and louvers, complete all as specified and directed by Engineer-in-Charge.

Exhaust fan, made of sturdy Engineering plastic complete with louvers shutter AC single phase 230v of size 250mm sweep ,copper windening including hole for fixing exhaust fan , complete all as specified and directed by Engineer-in-Charge.

Note :Schedule of credit to be deducted on acceptances of bid.Details of Schedule of credit is given in tender documentse.

Dhillon Construction Company (BID ID -3453301)

MOHAMMAD RASHID (BID ID -3447618)