GE 861 EWS-17 (T)/2025-26

Amount

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed by Engineer-in-Charge.

Dismantling timber scantlings (unframed) in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section In framed work complete all as specified and directed by Engineer-in-Charge.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-Charge.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engineer-in-Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed by Engineer-in-Charge.

M&L for Virified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

M&L for coloured joint free Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

M&L for glossy finished chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigments over and including 20mm thick screed bed of cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

M&L for 2nd class hardwood Plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads sizes exc 13 sqcm but n exc 25 sqcm in sectional area complete all as specified and as directed by Engineer-in-Charge.

S&F 4mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber frame work on ceiling complete all as specified and directed by Engineer-in-Charge.

S&F 4mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces; fixed with screws to timber frame work on Wall panalling complete all as specified and directed by Engineer-in-Charge.

M&L for 2nd class hardwood Plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads sizes exc 6 sqcm but n exc 13 sqcm in sectional area complete all as specified and as directed by Engineer-in-Charge.

M&L for 2nd class hardwood Plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads sizes n exc 03 sqcm in sectional area complete all as specified and as directed by Engineer-in-Charge.

M&L for Hardcore of broken stone or boulders and of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surfacecomplete all as specified and directed by Engineer-in-Charge.

M&L for 100mm thick cement concrete (1:4:8) type D2 (using 40mm graded crushed stone aggregate) as in floor, surface finished even and smooth (without using extra cement) and Spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green surfacecomplete all as specified and directed by Engineer-in-Charge.

Taking up or down 15mm dia galvanised steel tubing and connections, including cleaning for re fixing or removal to store complete all as specified and directed by Engineer-in-Charge.

S&F 15mm dia tubes, 'medium grade' galvanised,with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge.

Dismantling of water tanks exc 500 and n exc 1000 liters capacity and removing to store complete all as specified and directed by Engineer-In-Charge.

S&F 1000 ltrs capacity Rotational moulded polye thylene water storage tanks (cylindrical vertical with closed top) 3 layer hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed by Engineer-In-Charge.

Supply and fix ceramic floor mounted English type western water (EWC) closet single piece make CERA item code No A1014110, Tuscany white S-220, size 640x350x770mm rectangular in size, complete all as specified and as directed by Engineer-in-Charge.

Supplied & fixed 15mm 2nd class hard wood boarding, in wall panalling with nails in any situation (except flooring and skirting) Planed one side and edges tongued and grooved or rebatedcomplete all as specified and as directed by Engineer-in-Charge.

S&F 25mm thick boarding in floor and skirting planed one side & edges tongued and grooved or rebated, and fixed with nails complete all as specified and as directed by Engineer-In-Charge.

S&F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms) complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs 15mm dia Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge.

Taking down carefully aluminium/copper point wiring (light fan socket or power) complete and making good disturbed surfaces of walls, floor to match with existing and and removing unserviceable items from site for taking as credit complete all as specified and as directed by Engineer-in-Charge.

S&F in for point wiring for one light point/fan point controlled by one switch with 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green colour) as earth lead in and including PVC casing and capping medium grade of suitable size run on wall/surface with all fittings (ISI Marked) controlled by one switch including CI/MS/ wooden sunk box of required size, & as directed by Engr in Charge & 3mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified and as directed by Engineer-in-Charge.

All as per srl item No-28 here in above but for one 3 pin 5A socket outlet independent controlled by one switch complete all as specified and as directed by Engineer-in-Charge.

All as per srl item No-28 here in above but for one 5A socket outlet on the same board controlled by one switch complete all as specified and as directed by Engineer-in-Charge.

All as per srl item No-28 here in above but for 3 pin socket outlet 15 Amps independent board with 2.5 Sqmm complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement switch piano flush type, 05 / 06 Amps single pole, one way 240 volts complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement for switch socket combination 5/6 amps 5 pin flush type, 230 volts with box complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement Socket outlet 3 pin, 5A, flush type complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement socket out let, 6 pin 5 and 15 amps multi purpose 2 in 01 flush type, 230 volts complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement stepped type electronic fan regulator flush type on the existing sheet etc. AC, 230 volts, duly ISI marked with and including connector complete all as specified & directed by Engineer-in-Charge.

S&F in replacement lamp holder (Angular / Straight), insulated body, with back plate for batten fitting complete all as specified and as directed by Engineer-in-Charge.

S&F in repacement decorative ultra slim linear LED 18 Watt 4' long warm/White colour lighting fixture with extruded al heat sink, environment friendly, energy efficient ready to use pack including LED tube complete with inbuilt electronic driver, PCB, connector block etc. including connecting up three copper flexible cable from ceiling rose to fittings including connecting up and fixed on including two nos PVC square box of required size complete all as specified and as directed by Engineer-in-Charge.

S&F in repacement LED Lamp 9 W complete all as specified and as directed by Engineer-in-Charge.

S&F in repacement sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 4 way, with 200 Amps rated copper bus bar and IP - 43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as specified and as directed by Engineer-in-Charge.

S&F in repacement sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 8 way, with 200 Amps rated copper bus bar and IP - 43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as specified and as directed by Engineer-in-Charge.

S&F in repacement MCB, SP, AC, 240 volts "B" series capacity of 06 to 32 Amps, 10kA and making connections complete all as specified and as directed by Engineer-in-Charge.

S&F in repacement MCB, SPN (Single pole neutral), AC, 240 volts, B series capacity 63 Amps 10kA and making connections complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing including taking down (3 runs) old unserviceable 1100 volt grade copper conductor cable single core 1.5 sq mm complete all as specified and as directed by Engineer-in-Charge. (Note : Two run of single core PVC insulated cable with Copper conductor unsheathed cable of size 1.5 Sqmm and one run of 1.5 Sqmm PVC insulated copper conductor earth lead single core, one run of PVC conduit shall be measured as one unit for payment purpose)

Supply and fixing including taking down (3 runs) old unserviceable 1100 volt grade copper conductor cable single core 2.5 sq mm complete all as specified and as directed by Engineer-in-Charge. (Note : Two run of single core PVC insulated cable with Copper conductor unsheathed cable of size 2.5 Sqmm and one run of 2.5 Sqmm PVC insulated copper conductor earth lead single core, one run of PVC conduit shall be measured as one unit for payment purpose)

S&F in repacement taking down 1100 volts grade service cable with PVC insulated aluminium conductor 6 Sq mm nominal cross section 2 core complete all as specified and as directed by Engineer-in-Charge.

S&F in repacement taking down 1100 volts grade service cable with PVC insulated aluminium conductor 10 Sq mm nominal cross section 2 core complete all as specified and as directed by Engineer-in-Charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 3.5 core complete including taking out to old u/s switch complete all as specified and as directed by Engineer-in-Charge.

S&F in repacement Bed switch 5/6A complete all as specified and as directed by Engineer-in-Charge.

S&F in repacement Plug top 5/6A complete all as specified and as directed by Engineer-in-Charge.

S&F in repacement Plug top 15/16 A complete all as specified and as directed by Engineer-in-Charge.

S&F PVC Insulation Electrical Tape White color 19mm Wide and 10Meters in length complete all as specified and directed by Engineer-in-Charge.

M&L for switch socket combination out let 5/6 amps 5 pin flush type, 230 volts with box complete all as specified and as directed by Engineer-in-Charge.

M&L for switch socket combination out let, 6 pin 5 and 15/16 amps multi purpose 2 in 01 flush type, 230 volts with box complete all as specified and as directed by Engineer-in-Charge.

M&L for 2way Gang Box complete all as specified and as directed by Engineer-in-Charge.

M&L for 4 way Gang Box complete all as specified and as directed by Engineer-in-Charge.

S&F in repacement casing caping 20 mm complete all as specified and as directed by Engineer-in-Charge.

S&F in repacement for replacement of old unserviceable heating element Triangle with heating element AC 230 volt of rating 1500/2000 watt ISI marked triangular/circular type complete all as specified and as directed by Engineer-in-Charge.

S&F in repacement for replacement of old unserviceable thermostat with Thermostat switch for geyser AC 230 volt adjustable range as per sample complete all as specified and as directed by Engineer-in-Charge.

S&F in repacement LED Security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed by Engineer-in-Charge.

S&F in repacement LED Security light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

S&F in repalcement Connecting & testing Main switch 3 Phase 415V on load of rating 100 AMPS and including sheet enclouser complete including taking out to old U/S switch complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing in repalcement exhaust fan 250 mm sweep PVC body with louver, 240 volts AC single phase, 50 Hz, ISI marked, including necessary work in wall/sheet, including connection cable, nut bolt and other fixing material complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing in repalcement exhaust fan 300 mm sweep PVC body with louver, 240 volts AC single phase, 50 Hz, ISI marked, including necessary work in wall/sheet, including connection cable, nut bolt and other fixing material complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repalcement wall fan 450mm high speed, 230 volts single phase with jerk free oscillation, smooth running, three blades, pull cords incduding fixing arrangement complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing in repalcement BLDC ceiling fan 1200 mm sweep ,copper winding, double ball bearing with aluminium blade set of 3, length of down rod not less then 300 mm, single phase , 240 volts ISI marked , incuding connection with three core copper wire etc complete all as specified and as directed by Engineer-in-Charge.

M S BUILDERS (BID ID -3347831)

IRSHAD BASHIR (BID ID -3344650)

BHAT CONSTRUCTION AND BUILDERS (BID ID -3343344)

M/S BASHIR AND SONS (BID ID -3349882)