Replacement of existing old MS type SC towers by new DC towers in Loc no 104,105,106,108, 109, 111 and 116 of 110kV Salethur Konaje line coming under TLM section Kulashekhara of TLM sub-division Kavoor

Supply portion for Replacement of existing old MS type SC towers by new DC towers in Loc no 104,105,106,108, 109, 111 and 116 of 110kV Salethur Konaje line coming under TLM section Kulashekhara of TLM sub-division Kavoor

Fabrication and supply of Galvanised & high tensile Kalpatharu AEQUS line Design tower

a) Normal Tower Type DD+0 including stub and cleats - 1Nos

i) HT Portion including stub weight

b) Supply of Galvanised Bolts & nuts Including Step bolts

Fabrication and supply of Galvanised & high tensile M/s Kalpatharu Design for AEQUS line.

a) Normal Tower Type DB+0 including stub and cleats

i)HT Portion including stub weight

b) Supply of Galvanised Bolts & nuts Including Step bolts.

Fabrication and supply of Galvanised & high tensile M/s Kalpatharu Design for AEQUS line.

a) Normal Tower Type DB+6 including stub and cleats. 2 Nos

i)HT Portion including stub weight

b) Supply of Galvanised Bolts & nuts Including Step bolts. Quantity for 2 Nos of towers

Fabrication and supply of Galvanised & high tensile Kalpatharu Design for AEQUS line

a) Normal Tower Type DA+6 including stub and cleats.

i)HT Portion including stub weight

b) Supply of Galvanised Bolts & nuts Including Step bolts

Fabrication and supply of Galvanised narrow based 110kV DA+3 (NBT) transmission line Towers of KPTCL Design.

a) Narrow Based Tower Type DA+3 including stub and cleats

b)Supply of Galvanised Bolts & nuts Including Step bolts.

Fabrication and supply of Galvanised narrow based 110kV DA+3 (NBT) transmission line Towers of KPTCL Design a) Narrow Based Tower Type DC+0 including stub and cleats

b)Supply of Galvanised Bolts & nuts Including Step bolts.

Tower Accessories

a) Phase plate (set of 6nos per Tower)

b) Caution plate / Danger Board (1 No per Tower)

c) Number plate (1 No per Tower)

Providing cast iron pipe of 100mm ID 13mm thickness, 2.75 meters long with 2 part clamp out of G.I flat 50 x 6mm continuously welded alround the pipe using cast iron elding electrodes as per drawing i...

Supply of 50x6mm GI flat for Grounding of equipment with 50 x 6 mm G.I. Flat and connecting equipment to the earthmat/ground pit. Each point of earthing with all formation works like bending, twisting...

LYNX ACSR Conductor

Vibration dampers for ASCR Lynx conductor

C Type wedge connectors (2 nos per each Jump) LYNX to LYNX ACSR Conductor.

Mid span compression joint for Lynx ACSR conductor

Single tension clamp with arcing rods with hardware materials for insulators of 16mm balls size for Lynx ACSR conductor.

Single suspension clamp with arcing rods with hardware materials for insulators of 16mm balls size for Lynx ACSR Conductor

Double tension clamp with arcing rods with hardware materials for insulators of 16mm balls size for Lynx ACSR Conductor

Double suspension clamp with arcing rods with hardware materials for insulators of 16mm balls size for Lynx ACSR Conductor

90 KN Disc Insulators

Labour portion of Replacement of existing old MS type SC towers by new DC towers in Loc no 104,105,106,108, 109, 111 and 116 of 110kV Salethur Konaje line coming under TLM section Kulashekhara of TLM sub-division Kavoor

Check survey to be conducted during construction stage: Conducting detailed check survey along the approved route duly following the route alignment, GPS

Co-ordinates, submission of detailed line sche...

a) Sorting of tower parts made of fabricated angle iron

b) Assembling and errection of towers including tightening of bolts and nuts , loading, unloading at store and site.

c)Welding of tower Bolts & Nuts

Tower Accessories

a) Fixing Caution Plate/Danger Board (1 No per Tower)

b) Fixing Number plate ( 1 No per Tower).

c) Fixing Phase plate ( set of 3 nos per Tower)

(Labour for fixing=Rs238.00 per 3 Plates).

Grounding of equipments by providing cast iron pipe of 100mm ID 13mm thickness, 2.75 meters long with 2 part clamp out of G.I flat 50 x 6mm continuously welded alround the pipe using cast iron elding ...

Supplying and fixing A.C. Devices

(a) Supplying and fixing G.I Angle Iron 45 x 45 x 5 mm (1 Mtr. Length) with cleats, bolt & nutsas per specification and fixing above 0.5 m length each at inner and ou...

Supplying and fixing barbed wire as per specification.10mtrsX4sidesX 6 rounds/Tower ) 240m

Releasing of LYNX ACSR conductor

Releasing of conductors in hilly terrain with anchors provided at two/three span including the labour for releasing of insulator strings, vibration dampers and includi...

Stringing of LYNX ACSR Conductor

Stringing of LYNX ACSR conductor in special conditions where normal 5 spans are not encountered,whereas Anchors are from Loc.No 104-105-106-107=890mtrs, 107-108-109-11...

Dismantling of 110KV , Single circuit ‘B+0’ Mtr GI towers along with loading and unloading at site and store

Dismantling of 110KV , Single circuit ‘A+0’ Mtr MS/GI towers along with loading and unloading at site and store

Loading and Unloading of Dismantled towers

Transportation by 10 Tons Truck 8.0858(say 8.1) Tons of released materials are to be transported by 10 M.T lorry in 1 trip for a distance of 100 kmtrs

Civil portion for Replacement of existing old MS type SC towers by new DC towers in Loc no 104,105,106,108, 109, 111 and 116 of 110kV Salethur Konaje line coming under TLM section Kulashekhara of TLM sub-division Kavoor

Earth work in surface excavation by mechanical means for lowering & leveling the ground for all works other than foundation in all kinds of soils & upto depth not exceeding 300mm as per drawing and te...

Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...

Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...

Earth work excavation for Foundation by Mechanical means depth upto 1.50m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, includin...

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes...

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes...

Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tyin...

Providing and laying in position Cement Concrete for all Foundation works.

The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with sup...

Providing and laying in Cement Concrete for all Basement & surface level works, return walls, retaining walls, sunken floors etc. The granite/trap/basalt crushed graded coarse aggregates and fine aggr...

Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. T...

Additionalities for Formwork, Centering & Scaffolding-RCC Columns / Shaft (Slip Centering)

Additionalities for Formwork, Centering & Scaffolding-Earth retaining structures 10%

Additionalities for Formwork, Centering & Scaffolding-cement concrete drains 35%

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by r...

Replacement of existing old MS type SC towers by new DC towers in Loc no 104,105,106,108, 109, 111 and 116 of 110kV Salethur Konaje line coming under TLM section Kulashekhara of TLM sub-division Kavoor

Fabrication and supply of Galvanised & high tensile Kalpatharu AEQUS line Design tower

a) Normal Tower Type DD+0 including stub and cleats - 1Nos

i) HT Portion including stub weight

Earth work in surface excavation by mechanical means for lowering & leveling the ground for all works other than foundation in all kinds of soils & upto depth not exceeding 300mm as per drawing and te...

Check survey to be conducted during construction stage: Conducting detailed check survey along the approved route duly following the route alignment, GPS

Co-ordinates, submission of detailed line sche...

Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...

a) Sorting of tower parts made of fabricated angle iron

Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution li...

b) Supply of Galvanised Bolts & nuts Including Step bolts

b) Assembling and errection of towers including tightening of bolts and nuts , loading, unloading at store and site.

Earth work excavation for Foundation by Mechanical means depth upto 1.50m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, includin...

Fabrication and supply of Galvanised & high tensile M/s Kalpatharu Design for AEQUS line.

a) Normal Tower Type DB+0 including stub and cleats

i)HT Portion including stub weight

c)Welding of tower Bolts & Nuts

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes...

Tower Accessories

a) Fixing Caution Plate/Danger Board (1 No per Tower)

b) Supply of Galvanised Bolts & nuts Including Step bolts.

Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes...

b) Fixing Number plate ( 1 No per Tower).

Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tyin...

Fabrication and supply of Galvanised & high tensile M/s Kalpatharu Design for AEQUS line.

a) Normal Tower Type DB+6 including stub and cleats. 2 Nos

i)HT Portion including stub weight

c) Fixing Phase plate ( set of 3 nos per Tower)

(Labour for fixing=Rs238.00 per 3 Plates).

Providing and laying in position Cement Concrete for all Foundation works.

The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with sup...

Grounding of equipments by providing cast iron pipe of 100mm ID 13mm thickness, 2.75 meters long with 2 part clamp out of G.I flat 50 x 6mm continuously welded alround the pipe using cast iron elding ...

Supplying and fixing A.C. Devices

(a) Supplying and fixing G.I Angle Iron 45 x 45 x 5 mm (1 Mtr. Length) with cleats, bolt & nutsas per specification and fixing above 0.5 m length each at inner and ou...

b) Supply of Galvanised Bolts & nuts Including Step bolts. Quantity for 2 Nos of towers

Providing and laying in Cement Concrete for all Basement & surface level works, return walls, retaining walls, sunken floors etc. The granite/trap/basalt crushed graded coarse aggregates and fine aggr...

Supplying and fixing barbed wire as per specification.10mtrsX4sidesX 6 rounds/Tower ) 240m

Fabrication and supply of Galvanised & high tensile Kalpatharu Design for AEQUS line

a) Normal Tower Type DA+6 including stub and cleats.

i)HT Portion including stub weight

Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. T...

Releasing of LYNX ACSR conductor

Releasing of conductors in hilly terrain with anchors provided at two/three span including the labour for releasing of insulator strings, vibration dampers and includi...

Additionalities for Formwork, Centering & Scaffolding-RCC Columns / Shaft (Slip Centering)

b) Supply of Galvanised Bolts & nuts Including Step bolts

Additionalities for Formwork, Centering & Scaffolding-Earth retaining structures 10%

Stringing of LYNX ACSR Conductor

Stringing of LYNX ACSR conductor in special conditions where normal 5 spans are not encountered,whereas Anchors are from Loc.No 104-105-106-107=890mtrs, 107-108-109-11...

Fabrication and supply of Galvanised narrow based 110kV DA+3 (NBT) transmission line Towers of KPTCL Design.

a) Narrow Based Tower Type DA+3 including stub and cleats

Additionalities for Formwork, Centering & Scaffolding-cement concrete drains 35%

Dismantling of 110KV , Single circuit ‘B+0’ Mtr GI towers along with loading and unloading at site and store

b)Supply of Galvanised Bolts & nuts Including Step bolts.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by r...

Dismantling of 110KV , Single circuit ‘A+0’ Mtr MS/GI towers along with loading and unloading at site and store

Fabrication and supply of Galvanised narrow based 110kV DA+3 (NBT) transmission line Towers of KPTCL Design a) Narrow Based Tower Type DC+0 including stub and cleats

Loading and Unloading of Dismantled towers

b)Supply of Galvanised Bolts & nuts Including Step bolts.

Transportation by 10 Tons Truck 8.0858(say 8.1) Tons of released materials are to be transported by 10 M.T lorry in 1 trip for a distance of 100 kmtrs

Tower Accessories

a) Phase plate (set of 6nos per Tower)

b) Caution plate / Danger Board (1 No per Tower)

c) Number plate (1 No per Tower)

Providing cast iron pipe of 100mm ID 13mm thickness, 2.75 meters long with 2 part clamp out of G.I flat 50 x 6mm continuously welded alround the pipe using cast iron elding electrodes as per drawing i...

Supply of 50x6mm GI flat for Grounding of equipment with 50 x 6 mm G.I. Flat and connecting equipment to the earthmat/ground pit. Each point of earthing with all formation works like bending, twisting...

LYNX ACSR Conductor

Vibration dampers for ASCR Lynx conductor

C Type wedge connectors (2 nos per each Jump) LYNX to LYNX ACSR Conductor.

Mid span compression joint for Lynx ACSR conductor

Single tension clamp with arcing rods with hardware materials for insulators of 16mm balls size for Lynx ACSR conductor.

Single suspension clamp with arcing rods with hardware materials for insulators of 16mm balls size for Lynx ACSR Conductor

Double tension clamp with arcing rods with hardware materials for insulators of 16mm balls size for Lynx ACSR Conductor

Double suspension clamp with arcing rods with hardware materials for insulators of 16mm balls size for Lynx ACSR Conductor

90 KN Disc Insulators