Installation of Separator Filter for receipt of ATF at BKPL, Barauni Pump Station along with other associated Civil and Mechanical works

Amount

Installation of Separator filter at BPS

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50m and lift up to 1.5m, disposed earth to be levelled and neatly dressed. All kinds of soil. Earth Backfilling shall also be done as per site requirement. Restoration of work site to original.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes.Cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level

Centering and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns, etc. for mass concrete.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level. Mild steel and Medium Tensile steel bars.

Painting: Cleaning exposed steel surfaces of piping, equipment and valves etc. by sand blasting or with power wire brush (wherever sand blast cleaning is not possible) free of dust, grease, mill scales etc. priming with one coat of primer and painting the surfaces with two coats as per specification, with approved materials, paints, brushes, labour, equipment etc. and completing the job in all respects as per specification and instructions of the Site Engineer / EIC. 1.Inorganic Zinc Silicate. 2.High Build Epoxy MIO 3.Isocynate Aliphatic Poly Urethene(PU)

Painting: Cleaning exposed steel surfaces of piping, equipment and valves etc. by sand blasting or with power wire brush (wherever sand blast cleaning is not possible) free of dust, grease, mill scales etc. priming with one coat of primer and painting the surfaces with two coats as per specification, with approved materials, paints, brushes, labour, equipment etc. and completing the job in all respects as per specification and instructions of the Site Engineer / EIC. 1.Inorganic Zinc Silicate. 2.High Build Epoxy MIO 3.Isocynate Aliphatic Poly Urethene(PU)

Painting: Cleaning exposed steel surfaces of piping, equipment and valves etc. by sand blasting or with power wire brush (wherever sand blast cleaning is not possible) free of dust, grease, mill scales etc. priming with one coat of primer and painting the surfaces with two coats as per specification, with approved materials, paints, brushes, labour, equipment etc. and completing the job in all respects as per specification and instructions of the Site Engineer / EIC. 1.Inorganic Zinc Silicate. 2.High Build Epoxy MIO 3.Isocynate Aliphatic Poly Urethene(PU)

Taking delivery of pipe, pipe fittings, steel flanges, spiral wound metallic gaskets & fasteners from designated location within station premises, transporting the same to site, cutting of pipe and / or weld joint , edge preparation, bending, lining up, welding and installing pipes and pipe fittings, flanges, elbows, equal and reducing outlet tees, concentric/eccentric reducers, y-type strainers, drain funnels, vent pipes and tapping for instruments such as pressure gauges, thermal relief valves, thermowells etc., installing above ground/ Under ground at all elevations/ Depth connecting with equipment nozzles, valves, vessels, in line instruments etc., welded and threaded pipe line of different pressure ratings, flushing pipes by water after cleaning by compressed air, hydrostatic testing of each section to the specified pressure, draining the water, tie-in, final cleaning-up and dispoal of wastes and surpluses including providing all inputs such as labour, material, equipments and consumables necessary to perform the work and completing the work in all respects in accordance with the drawings, specifications and instructions of Site Engineer / EIC. (inch Dia means Pipe Dia . Measurement of inch dia will be = No of Joint * Pipe/elbow OD in inch.)

Dismantling of Piping (Aboveground): Dismantling of existing over ground piping works including manifolds of all types and sizesby opening flange joints or by gas cutting/ cold cutting or any other approved suitable means without damaging other portions of work. The job includes cutting the pipes to required sizes as directed, taking out valves, flanges, tees, bends, NRV, gaskets nuts, bolts etc. attached supports alongwith any instruments such as pressure gauge, temperature gauge etc. handling, transporting and storing at owner's designated store in safe manner to avoid damage including supply of all labour, materials, equipments, consumables etc. necessary to perform and complete the work in all respects as per drawings, instructions of the Site Engineer / EIC (payment shall be made on linear measurement of dismantled piping including bends tees etc.). Note : The contractor shall indicate the piping system to be dismantled and shall take specific approval from the Site engineer before dismantling of pipe. Certain redundant pipes which in the opinion of the Owner need not be retrieived, those items shall not be dismantelled.

Supply and delivery of Spiral Wound Metallic Gaskets at respective stations as per Station wise Break up of material supply and as per technical specifications from approved vendors specified in tender document. 12" x ANSI 150 Sr. SWMG

Supply and delivery of Spiral Wound Metallic Gaskets at respective stations as per Station wise Break up of material supply and as per technical specifications from approved vendors specified in tender document. 10" x ANSI 600 Sr. SWMG

Supply and delivery of Steel Flanges at respective stations as per Station wise Break up of material supply and as per technical specifications from approved vendors specified in tender document. Cost shall be inclusive of all chages including charges for inpsection of materials by approved TPI, Taxes etc. 12", WNRF FLANGE, ANSI - 150# (B 16.5)

Supply and delivery of Steel Flanges at respective stations as per Station wise Break up of material supply and as per technical specifications from approved vendors specified in tender document. Cost shall be inclusive of all chages including charges for inpsection of materials by approved TPI, Taxes etc. 10", WNRF FLANGE, ANSI - 150# (B 16.5)

Supply and delivery of Steel Flanges at respective stations as per Station wise Break up of material supply and as per technical specifications from approved vendors specified in tender document. Cost shall be inclusive of all chages including charges for inpsection of materials by approved TPI, Taxes etc. 2" x ANSI 150 Sr.WNRF

Supply and delivery of Steel Flanges at respective stations as per Station wise Break up of material supply and as per technical specifications from approved vendors specified in tender document. Cost shall be inclusive of all chages including charges for inpsection of materials by approved TPI, Taxes etc. 1" x ANSI 150 Sr.WNRF

Supply and delivery of pipe fittings at respective stations as per Station wise Break up of material supply and as per technical specifications from approved vendors specified in tender document. Cost shall be inclusive of all chages including charges for inpsection of materials by approved TPI, Taxes etc. 12" ANSI 150# 90 deg LR Bends

Supply and delivery of pipe fittings at respective stations as per Station wise Break up of material supply and as per technical specifications from approved vendors specified in tender document. Cost shall be inclusive of all chages including charges for inpsection of materials by approved TPI, Taxes etc. 10" ANSI 150# 90 deg LR Bends

Supply and delivery of pipe fittings at respective stations as per Station wise Break up of material supply and as per technical specifications from approved vendors specified in tender document. Cost shall be inclusive of all chages including charges for inpsection of materials by approved TPI, Taxes etc. 1" ANSI 150# 90 deg LR Bends

Supply and delivery of pipe fittings at respective stations as per Station wise Break up of material supply and as per technical specifications from approved vendors specified in tender document. Cost shall be inclusive of all chages including charges for inpsection of materials by approved TPI, Taxes etc. 2" ANSI 150# 90 deg LR Bends

Supply of ASTM A106 Gr.B pipes at respective stations as per Station wise Break up of material supply and as per technical specifications from approved vendors specified in tender document. Cost shall be inclusive of all chages including charges for inpsection of materials by approved TPI, Taxes etc. 2.375" OD x 0.218"WT ASTM A 106 Gr B bare pipe

Supply of ASTM A106 Gr.B pipes at respective stations as per Station wise Break up of material supply and as per technical specifications from approved vendors specified in tender document. Cost shall be inclusive of all chages including charges for inpsection of materials by approved TPI, Taxes etc. 1.315" OD x 0.179"WT ASTM A 106 Gr B Bare pipe

Valves: Taking delivery of valves of all types and pressure rating from the designated location within station premises, transporting the same to site, erecting above ground on preconstructed foundations or underground including earth work in excavation and filling for under ground valves at elevations specified in the drawings, priming and painting of above ground valves, PU Painting of under ground portions (if applicable) including all inputs, labour, material and consumable (other than those specifically undertaken to be supplied by the owner) and completing the work in all respects in accordance with the drawings, manufacturer's installation instructions and specifications and instructions of the Site Engineer / EIC. 2" ANSI 150 HOV F/F API 6D Gate Valve

Valves: Taking delivery of valves of all types and pressure rating from the designated location within station premises, transporting the same to site, erecting above ground on preconstructed foundations or underground including earth work in excavation and filling for under ground valves at elevations specified in the drawings, priming and painting of above ground valves, PU Painting of under ground portions (if applicable) including all inputs, labour, material and consumable (other than those specifically undertaken to be supplied by the owner) and completing the work in all respects in accordance with the drawings, manufacturer's installation instructions and specifications and instructions of the Site Engineer / EIC. 1"x ANSI 800# HOV W/W API 602 Gate Valve

Taking delivery of pipes , Above ground piping: (12" Process Piping)Above ground process piping: Taking delivery & transporting of pipes from designated stock pile location- fittings, steel flanges, spiral wound metallic gaskets & fasteners from designated location within station premises, transporting the same to site, fabrication and erection of above ground piping including cutting, edge preparation, bending, threading, lining up, welding and intsalling pipes and pipe fittings, flanges, elbows, equal and reducing outlet tees, concentric/eccentric reducers, y-type strainers, drain funnels, vent pipes and tapping for instruments such as pressure gauges, thermal relief valves, thermowells etc., installing above ground at all elevations connecting with equipment nozzles, valves, vessels, in line instruments etc., welded and threaded pipe line of different pressure ratings, flushing pipes by water after cleaning by compressed air, cleaning by card board blasting, hydrostatic testing of each section to the specified pressure, draining the water, tie-in, final cleaning-up and dispoal of wastes and surpluses including providing all inputs such as labour, material, equipments and consumables necessary to perform the work (other than those specifically under taken by the owner in this contract) and completing the work in all respects in accordance with the drawings, specifications and instructions of Site Engineer / EIC

Taking delivery of pipes , Above ground piping: (10" Process Piping)Above ground process piping: Taking delivery & transporting of pipes from designated stock pile location- fittings, steel flanges, spiral wound metallic gaskets & fasteners from designated location within station premises, transporting the same to site, fabrication and erection of above ground piping including cutting, edge preparation, bending, threading, lining up, welding and intsalling pipes and pipe fittings, flanges, elbows, equal and reducing outlet tees, concentric/eccentric reducers, y-type strainers, drain funnels, vent pipes and tapping for instruments such as pressure gauges, thermal relief valves, thermowells etc., installing above ground at all elevations connecting with equipment nozzles, valves, vessels, in line instruments etc., welded and threaded pipe line of different pressure ratings, flushing pipes by water after cleaning by compressed air, cleaning by card board blasting, hydrostatic testing of each section to the specified pressure, draining the water, tie-in, final cleaning-up and dispoal of wastes and surpluses including providing all inputs such as labour, material, equipments and consumables necessary to perform the work (other than those specifically under taken by the owner in this contract) and completing the work in all respects in accordance with the drawings, specifications and instructions of Site Engineer / EIC

Taking delivery of pipes , Above ground piping: (2" Process Piping)Above ground process piping: Taking delivery & transporting of pipes from designated stock pile location- fittings, steel flanges, spiral wound metallic gaskets & fasteners from designated location within station premises, transporting the same to site, fabrication and erection of above ground piping including cutting, edge preparation, bending, threading, lining up, welding and intsalling pipes and pipe fittings, flanges, elbows, equal and reducing outlet tees, concentric/eccentric reducers, y-type strainers, drain funnels, vent pipes and tapping for instruments such as pressure gauges, thermal relief valves, thermowells etc., installing above ground at all elevations connecting with equipment nozzles, valves, vessels, in line instruments etc., welded and threaded pipe line of different pressure ratings, flushing pipes by water after cleaning by compressed air, cleaning by card board blasting, hydrostatic testing of each section to the specified pressure, draining the water, tie-in, final cleaning-up and dispoal of wastes and surpluses including providing all inputs such as labour, material, equipments and consumables necessary to perform the work (other than those specifically under taken by the owner in this contract) and completing the work in all respects in accordance with the drawings, specifications and instructions of Site Engineer / EIC

Taking delivery of pipes , Above ground piping: (1" Process Piping)Above ground process piping: Taking delivery & transporting of pipes from designated stock pile location- fittings, steel flanges, spiral wound metallic gaskets & fasteners from designated location within station premises, transporting the same to site, fabrication and erection of above ground piping including cutting, edge preparation, bending, threading, lining up, welding and intsalling pipes and pipe fittings, flanges, elbows, equal and reducing outlet tees, concentric/eccentric reducers, y-type strainers, drain funnels, vent pipes and tapping for instruments such as pressure gauges, thermal relief valves, thermowells etc., installing above ground at all elevations connecting with equipment nozzles, valves, vessels, in line instruments etc., welded and threaded pipe line of different pressure ratings, flushing pipes by water after cleaning by compressed air, cleaning by card board blasting, hydrostatic testing of each section to the specified pressure, draining the water, tie-in, final cleaning-up and dispoal of wastes and surpluses including providing all inputs such as labour, material, equipments and consumables necessary to perform the work (other than those specifically under taken by the owner in this contract) and completing the work in all respects in accordance with the drawings, specifications and instructions of Site Engineer / EIC

Installation of Valves:10"( Process Piping): GATE VALVES: 150#"Valves: Taking delivery of valves of all types and pressure rating from the designated location

Installation of Separator Filter: Transportation of Seperator Filter from Owner's storage point to work site, opening of Separator filter door & replacement of old filters and any other defective parts/O-rings by owner supplied filters & Material , assembly of parts, sub-assemblies (including internal), erection at all elevation , aligning , tightening of bolts, grouting of owner supplied foundation bolts , cleanning, Hydrotesting , flushing by water , draining, drying by compressed air and installation of all mounting and completing the works in all respect including earthing protection by way of fixing strips and with connection with existing earthing as per direction of Site Engineer/ EIC. Job also includes supplying of all types, of tools, tackles, lifting arrangement, cranes, tractor trolley and equipments, machineries all consumables and labour to complete the job in a workman like manner, erection and removal of steel sacffolding wherever required, area preapation for hot jobv and area cleanning after completion of work. All jobs are to be carried out as per the instructions and to the full satisfaction of the Engineer-in-charge.

RADIOGRAPHY OF 2 PIPING WORKS Performance of radiographic inspection on all type & sizing of piping/pipefittings in position at all heights inclusive of providing sources, film, chemicals, & all necessary equipment’s, consumables etc. complete in all respect as per specification & instruction of the Engineer-in-Charge. Measurement of inch dia will be = No of Joint * Pipe Dia in inch."

RADIOGRAPHY OF 1 PIPING WORKS Performance of radiographic inspection on all type & sizing of piping/pipefittings in position at all heights inclusive of providing sources, film, chemicals, & all necessary equipment’s, consumables etc. complete in all respect as per specification & instruction of the Engineer-in-Charge. Measurement of inch dia will be = No of Joint * Pipe Dia in inch."

Supply and delivery of Steel Fasteners at respective stations as per Station wise Break up of material supply and as per technical specifications from approved vendors specified in tender document. 0.625" Dia. X 4.00" Length

Supply of Valves at respective stations as per technical specifications from approved vendors in the tender document. Cost shall be inclusive of all charges including charges for inpsection of materials by approved TPI, Taxes etc. 1" x 800# Gate valve HOV w/w

Supply of Valves at respective stations as per technical specifications from approved vendors in the tender document. Cost shall be inclusive of all charges including charges for inpsection of materials by approved TPI, Taxes etc. 2"x ANSI 150 # HOV F/F API 600 Gate Valve

Supply and delivery of Spiral Wound Metallic Gaskets at respective stations as per Station wise Break up of material supply and as per technical specifications from approved vendors specified in tender document 2" x ANSI 600 Sr. SWMG

Supply and delivery of Spiral Wound Metallic Gaskets at respective stations as per Station wise Break up of material supply and as per technical specifications from approved vendors specified in tender document. 1" x ANSI 600 Sr. SWMG .

instalation of 12 Valves: Taking delivery of valves of all types and pressure rating from the designated location within station premises, transporting the same to site, erecting above ground on preconstructed foundations or underground including earth work in excavation and filling for under ground valves at elevations specified in the drawings, priming and painting of above ground valves, PU Painting of under ground portions (if applicable) including all inputs, labour, material and consumable (other than those specifically undertaken to be supplied by the owner) and completing the work in all respects in accordance with the drawings, manufacturer's installation instructions and specifications and instructions of the Site Engineer / EIC."

RADIOGRAPHY OF 10 NB PIPING WORKS Performance of radiographic inspection on all type & sizing of piping/pipefittings in position at all heights inclusive of providing sources, film, chemicals, & all necessary equipment’s, consumables etc. complete in all respect as per specification & instruction of the Engineer-in-Charge. "

RADIOGRAPHY OF 12 NB PIPING WORKS Performance of radiographic inspection on all type & sizing of piping/pipefittings in position at all heights inclusive of providing sources, film, chemicals, & all necessary equipment’s, consumables etc. complete in all respect as per specification & instruction of the Engineer-in-Charge. Measurement of inch dia will be = No of Joint * Pipe Dia in inch."

Single Cut Joint 10" and Hook-up:Single Cut Joint Hook-up: Cutting of portion of existing piping, trimming, grinding, bevelling the

Single Cut 12" Joint and Hook-up:Single Cut Joint Hook-up: Cutting of portion of existing piping, trimming, grinding, bevelling the

Double Cut Joint 10" and Hook-up:Double Cut Joint Hook-up: Cutting of portion of existing piping upto and including a length of 500

Double Cut Joint 12" and Hook-up:Double Cut Joint Hook-up: Cutting of portion of existing piping upto and including a length of 500

Installation of Valves 12":( Process Piping): GATE VALVES: 150#"Valves: Taking delivery of valves of all types and pressure rating from the designated location

M/s ABDHESH KUMAR SINGH

SIKANDAR KHAN

Uday Engineering Works

PULSE ENGINEERING