SPL REPAIR TO BLDG NO P 73 (URC BLDG) AT MIL STN GAYA

Amount

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M & L brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as spd.

S & F of Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M&L two coat of syntetic enamel paint over new steel surface of any description over 10cm in width or grith not otherwise described over one coat red oxide primer including preparation of surfaces complete.

Taking down chowkhats for frames exc 1.5 Sqm but not exc 4.00 Sqm.

M & L for pressed steel door frame size 105 mm x 60 mm made of 1.25 mm thick sheet including necessary fixing lugs, hinges, lock strike plate etc., complete, all as specified.

M & L for 30 mm thick Flush shutters, solid core construction, with block board core and 5 mm thick plywood face panels on both side, commercial type on both sides covered face veneered decorative type etc.

S&F as in repair 150mm long aluminium anodised barrel tower bolt complete.

S&F as in repair alluminum alloy, anodised, cast type or extruded section, sliding door bolt with hasp & staple (bolt type) with fixing clips and bolts and 300 mm long complete all as specified.

M&L for Preparation of old painted surfaces of wood and wood based surfaces of any description, over 10cm in width or girth and apply one coat of synthetic enamel paint complete all as specified and directed.

Taking down cement plaster any description on brick or stone walls etc including ,raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for rendering 10mm thick internal surfaces on other than fair faces of brick work in cm 1:6 as directed by Engr-in-charge.

M&L for 1 mm thick Birla white putty/JK white wall care putty on walls/Ceiling surfaces.

M&L for applying two coat of acrylic distemper over a coat of primer incl preparation of old/new plastered wall surfaces.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

M&L 25 mm thick cement concrete type B-1 (1:2:4) using 20 mm graded stone aggregate as in levelling of flooring complete all as specified and directed.

M & L for vitrified ceramic tiles double charge light shed of 7.5 mm thick (square/ rectangular) polished, area of each tiles n.exc 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4 complete.

S&F Powder coated aluminium frame/shutters for windows, ventilators sliding/openable etc icluding joining cleat for fixing, locking arrangement, rubber beading, screws, etc complete all as specified. Note : (i) Glazing and wire mesh shall be measured and paid separetely. (ii) Item shall be paid as per weight of aluminium section (iii) The rate quoted shall be inclusive of the cost of neoprene beading, glazing pin, screws and powder coated fittings such as locking arraangement etc as required, which shall not be measured for arriving the weight (iv) The rate shall also be inclusive of complete packing with silicon gel around contacting surfaces of aluminium work, and including matching the existing.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares of any size complete all as specified and directed by Engr-in-charge.

S&F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperature 1.18mm and fixed with beeding/Staples directed by Engg- in- charge.

S& F 12 mm toughened glass as in Sliding /openabl doors/partition inluding hinges,handles, locking arrangement and similar work including cutting to shape, drilling holes required as directed

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement.

M&L for granite (any type) work (table rubbed and polished) 18 to 20 mm thick in working platform and like including cutting for sink etc. in cement mortar (1:4) including rounding of edges and pointing in white cement (1:2) using marble dust with admixture of pigment to match.complete all as specified and as directed

OM SAI NATH CONSTRUCTION (BID ID -3347120)

SINGHAL ENTERPRISES (BID ID -3356803)

M/S ABHAY KUMAR AND BROTHERS (BID ID -3347773)

universal enterprises (BID ID -3346438)

M/S V D ASSOCIATES (BID ID -3345725)

RKT ENGINEER & SONS (BID ID -3345217)

Maa Bhawani Construction (BID ID -3347586)