PROVISION OF FALSE CEILING, HARD STANDING, ADDN ALTN TO TWO ROOMS, ETC FOR CERTAIN UNITS UNDER AGE B/R II OF GE (CENTRAL) BAGALORE

Amount

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil.

All as per item No 2 above but depth exc 1.5 metre and not exc 3.0 metre

Cutting opening through brick wall built in cement mortar for making door or window opening and removing rubbish off MOD land all as directed.

Cutting out old bricks,forming toothing for,and bonding new into old work incuding value of new materials entering old walls and jointing and pointing(measured on vertical face in contact with old wall only) new wall built in CM 1:6

Returning, filling in hard/dense soil, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

Removing excavated surplus material to a distance exc 250m but n exc 500m and depositing where directed at a level not exc 1.5 above the starting point complete all as directed.

M&L for providing plain cement concrete type D2 1:4:8 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete.

Dismantling of AC Sheets in roof covering including ridges

Taking down chowkats or frames n exc 1.5 SqM with shutters ( without taking off shutters from the frame)

Taking down chowkats or frames exc 1.5 SqM and not exceeding 4 SqM with shutters ( without taking off shutters from the frame)

M&L for Pre-cast cement concrete type C1 1:3:6 (using 20mm graded stone aggregate) block masonry with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6, complete all as directed.

M&L for Pre-cast cement concrete type B1 1:2:4 (using 20mm graded stone aggregate) block masonry with solid blocks,notexceeding 10 cm in width and setting in cement mortar 1:4, complete all as directed.

M&L for 40mm thick Cement concrete type B0 1:2:4 (using 12.5mm graded stone aggregate) mixed with integral water proofing compound by weight of cement as per manufacturer's instructions, as in damp proof course to horizontal or vertical surfaces including necessary formwork complete. (Note : WPC shall be measured and paid separately against respective item as supply only).

Use and waste of form work to sides and bottom of of RCC lintel bands for Rough finished surface..

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

Use and waste of form work to sides of RCC slabs for Rough finished surface.

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses,etc. vertical or to batter rough finished surfaces. of cocrete.

M&L for 1:2:4 type B1(20 mm graded aggregate) as in RCC lintel bands etc

M&L for RCC- 1:2:4 type B1 (20mm graded stone aggregate) as in slab supported on wall, beam and columns in floors, roof, landing and in shelves and the like

M&L for RCC- 1:2:4 type B1 (20mm graded stone aggregate) as in Walls, retaining walls, basement walls, ballast walls and the like;any thickness; above top of footings; including attached pilaster and buttresses

Providing precast cement concrete 1:2:4 type B0 (12.5mm graded stone aggreghate) louvres and jallies, 25mm thick (measured solid), including all moulding but excluding frame set in cement mortar 1:4

50mm x 47 mm size PVC solid door frame of size made out of 5mm plain Colour PVC sheet reinforced with MS square tube , supplying and fixing in opening as per specification and drawing shown in SSR 2004 Part II.

S&F 30mm thick factory made solid panel PVC door shutter (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain Colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck in side with solvent cement for stiles and plain Colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain Colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement supplying and fixing in the frame at site as per specification and drawing shown in SSR 2004 Part II.

M&L for hard core using broken/crushed stone aggregate of guage not exc 63mm, deposited, spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surfaces all as directed.

M&L cement concrete 1:3:6 type C-1 using 20mm graded stone aggregate as in bed blocks, coping, padding/levelling concrete for fixing water tank etc., including necessary form work and complete all as specified and directed.

M & L for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

M&L for 100 mm thick cement concrete 1:4:8 mix, type D2 using (40 mm graded stone aggregate), as in sub base of flooring.

M & L for 40 mm thick, plain cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in flooring etc and finished the surface even and fair to receive floor finishes

M & L for 25 mm thick, plain cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in flooring etc and finished the surface even and fair to receive floor finishes

S & F well seasoned 2nd class hard wood plain, solid, straight chowkat and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S & F Mild steel work as in band, strap, hold fast, cleat, support, hook, hinges, base tie for door frame etc and other similar items conforming to Fe-410-0 or Fe-310-0 complete all as specified and as directed.

S&F for 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides

S & F 35 mm thick, glazed/skeleton shutters with second class hard wood,open rebated and prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass, etc complete as specified and directed . Sizes of members of shutters as specified in SSR Part I, Section -8, clause 8.24 (b).

S & F 150 mm size, Aluminium handles, cast type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S & F 100mm butt hinges, medium weight, cold rolled mild steel

S & F 150 mm long, Aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and directed.

S & F Aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, length of bolt of 250 mm anodised finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

Material and labour for false of 4 mm thick designer ceiling board, pre- painted cement fibre board of size 595x595 mm of any texture (lake and Hill, Oceanic, cascade or Electra) using GI snap grid system with Rool formed out of hot dip galvanized steel capings (Powder coated).The suspension system consisting of perimeter wall angle of size 24x24 mm 0.45 mm of thick GS sheet to secure on wall portion face with the help of rawl plug @ 450 mm C/C universal main runner of T shaped section with single rotary stitching of size (32x24 mm) made from 0.33 GS sheet of length 3.60 mtr to be spaced @ 1200 mm C/C cross runner T shaped with double rotary stitching of size (30x24 mm) of length 1200mm made from 0.25 mm thick GS sheet spaced @ 600 mm C/C (120x600mm) of size module immediate T shaped cross runner of size (25x24 mm) of length 600 mm made of 0.25 mm thick GS Sheet to form (600x600mm) size of module incl suspension of the ceiling from the roof /structural members,soffit angles,cleats,G I suspenders of 3 mm thick GI wire and level adjusters incl. U clamp of GI fixed in ceiling all complete and incl cost of making opening for light fitting diffusers, cut out to te required line and shape as per manufacture’s recommendations at any height complete all as specified and as directed by Engr –in charge .Mak of Board : Ramco/Charminar /Armstrong/. Everest

M & L for TMT steel bars 10mm dia and over, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for TMT steel bars 8mm dia, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Cutting chases in block masonry walls ,pinning in,making good to facings and pointing inCM 1:3 concealed water tubing walls n exc 10 cm girth complete all as directed .

S & F Rolled mild steel work as in truss, purlins, posts etc using angle, or tee sections, fixed independently, without connecting plates, etc including cutting, welding, drilling holes etc complete. Steel section conforming to Fe-410-W (Gde-E-250) quality-B complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick (total coated thickness) of any colour having tensile strength of 550 Mpa and finished with resin coat on both surfaces @ 150 gm/ sqm, as in roof covering/ cladding to wall, fixed with self tapping screws as specified

S&F pre-painted galvalume aluminium zinc coating Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges, hips, valley gutters, drip and straight flashing, fixed with self tapping screws as specified

M & L for rendering 10 mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and fair without using extra cement complete all as specified and directed.

M & L for rendering 15 mm thick in two layer (10mm and 5mm thick) on fair faces of brick work or concrete surfaces in cement mortar 1:4, mixed with integral water proofing compound at top 5mm thick layer by weight of cement as per manufacturer's instructions and finished the surface even and smooth without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item supply only).

"Supply only" integral water proofing compound (ISI marked) complete all as specified and directed. Make : Dr. FIXIT

M&L for applying three coats of white wash after preparation of new plaster surface of wall complete all as specified and directed.

M&L for applying three coats of white wash after preparation of new plaster surface of ceiling complete all as specified and directed.

M&L for applying two coats of cement base paint over one coat of alkali resistant priming coat on walls including preparation of new plastered surfaces.

M&L for two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer after preparation of new steel surface of any description, not otherwise described, over 10 cm width or grith complete all as specified and directed.

M&L Preparing old surfaces of wall surfaces by complete removal of existing treatment and applying two coat of oil bound distemper over one coat of primer andchalk whitening on walls all as specified

M&L Preparation of old surfaces of Wall and applying one coat of white wash on wall all as specified and directed.

S&F Anodised Aluminium Powder Coated Windows sliding windows frame with jointing cleat for fixing etc and aluminium anodised skelton windows& shutter fixed with glass or gauge, sliding type (Three track frame suitable for 2 nos glazed shutter and 1 no wire mesh shutter) without sash bars using standared aluminium section (Shutter section weight not less than 0.45KG/RM) incl necessary jointing cleats, glazing clips, rubber packing, anodised aluminium snap beadings screws, anodised aluminium fittings such as handles stainless steel adjustable friction stay hinges etc complete all as directed by Engineer-in-Charge. NOTE;- However unit rate includes cost of rubber beading, fitting such as handles, SS friction stay hinges and fixing of glass / S S wire mesh etc.

S&F Anodised Aluminium Powder Coated Ventilators with frames suitable for top portion with fixed wire mesh and louvers with glazing, bottom portion with fixed glass(Pinhead glass) incl jointing cleat for fixing glass, wire mesh etc incl necessary jointing cleats, glazing clips, rubber packing,anodised aluminium snap beadings, screws, anodised aluminium fittings such as handles stainless steel adjustable friction stay hinges etc as required complete all as directed by Engineer-in-Charge. NOTE;- However unit rate includes cost of rubber beading, fitting such as handles, SS friction stay hinges and fixing of glass / S S wire mesh etc.

Supply only 4mm figured glass pin head type for fixing to aluminium joinery in squares not exc. 0.5 SqM in each pane

Supply only stain less wire mesh wire cloth,0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stain less steel wire staplesfor fixing to aluminium joinery

M&L for two coats of synthetic enamel paint over one coat of pink primer after preparation of wooden surface of any description, not otherwise described, over 10 cm width or grith complete all as specified and directed.

M&L Preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed..

M&L Preparation of old painted steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed.

Demolition of plain cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness. (below or above ground level) complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including raking out joints,hacking for key ,scrubbing down with water,etc

Supply and fix 110mm bore PVC (SWR) Pipes Type "B" conforming to IS 13592, single socketed in any length with rubber ring joints, laid in trenches floor etc. complete all as specified and directed.

Supply and fix 110mm bore PVC (SWR) Pipes Type "B" conforming to IS 13592, single socketed in any length with rubber ring joints,fixed on walls etc. complete all as specified and directed.

Supply and fix 75 mm bore PVC (SWR) Pipes Type "B" conforming to IS 13592, single socketed in any length with rubber ring joints, laid in trenches, floor etc. complete all as specified and directed.

PVC (SWR) bends 75mm dia any radius with or without access door

S&F 110mm dia PVC (SWR) branch piece (single Y) equal or unequal with access door

PVC (SWR) junction single, (Single T) equal or unequal of 75mm bore of pipe

PVC (SWR) bends 75mm dia provided with access doors.

PVC (SWR) vent cowl 110mm bore.

S & F 1000 litres capacity Rotational moulded polythene water storage tanks(cylindrical vertical with closed top) hoisted in position all as specified in SSR Part I

S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors 150mm dia

Supplying and laying of 20mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S&F of 25 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings, fixed complete to walls and ceilings or laid

M&L cement concrete 1:4:8 type D2 using 40mm graded stone aggregate to bed concrete to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150mm dia pipe

Loose filling with aggregates of gauge 80 to 150 mm in soakage pits, soakage wells

M&L for Precast RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in cover slabs (for manholes etc), lintels, window cills and similar articles with plain faces and set in cement mortar 1:6 including necessary formwork complete all as specified and directed. (Note: Reinforcement steel shall be measured and paid separately under respective item)

M & L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, in vertical suirfaces cut and shape the required size, including 10 mm thick backing coat in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M&L Preparing new plastered surfaces of wall surfaces for applying two coat of oil bound distemper over one coat of primer and putty on walls all as specified

S&F in Repair Vitreous China Wash hand basin along with Pedestal, white flat back size 550x400 mm including brackets including Pillar Tap 15 mm bore Chromium plated cast copper alloy with capstan heads, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts PVC waste pipe of 32 mm bore all as specified & directed by Engineer-in-charge.

Bip taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed to 15mm pipe, complete all as specified and directed.

15mm bore Stop valves angle cock fancy type cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

PVC Connection 15mm dia with PTMT nuts of length 450mm.

Vitreous china urinal, bowl type size of 430 x 370 x 340mm white with grating and union of discharge pipe (back or corner wall type) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, flush pipe, grating and union for discharge pipe and 32mm dia PVC waste pipe complete all as specified and directed.

Self closing with push button CP stop valves, cast copper alloy, screwed both ends for 15mm iron pipe or unions for urinals

Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including PVC SWR P trap connecting to flush pipe and to anti syphonage pipe, etc. complete including making good to floor, fixed in repairs complete all as specified and directed.

PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets

M&L 75mm PVC (SWR) floor trap, palin with grating including jointing with solvent cement

S&F Tubular Towel Rail of 20mm dia of 60cm in length, D shaped, with brass chromium plated brackets all as specified and directed.

S & F in repair 15 mm bore, bib taps fancy tyupe with capstan head, PTMT, any colour, high pressure screwed for iron pipes and fixed complete all as specified and directed.(min weight 90 gms)

S&F concealed stop cock Fancy Type chromium plated with long shank and cup (concealed type)ad, screwed down, screwed for iron pipes 20 mm OD CPVC pipes

S&F Fancy Type 2 in 1 Bib Taps 15 mm bore cast copper alloy Chromium plated with capstan head, screwed down, screwed for iron pipes.

S&F CP health faucet with 1 mtr long flexible tube suitable for 15 mm dia bore water tube or fitting

S&F Vitreous China Wash down water closet pedastel pan (EWC) white in colour with and incl PVC Low levell flushing cistern, plastic water seat and cover (white )with close pattern with recessed bottom and cover and MS chromium plated hinging device incl connection to outgoing pipe and flushing pipe complete all as specified & directed by Engineer-in-charge.

Taking down carefully aluminium point wiring ( Light, fan, socket or power) complete including fittings and fixtures such as switches, ceiling rose, pendent, lamp, lamp holder, regulator, switch socket out let, light fittings etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions seperately)and making good disturded surfaces of wall, floors, etc.

M&L for Point wiring on surface of wall/false ceilingwith PVC insulated and unsheathed cable single core multistranded copper conductor FRLS of 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn in and including PVC rigid non metalic grey conduit conforming to IS-9537 with all accessories ,including fabricated MS terminal boxes fixed flush with wall surface with 3mm thick masonite laminated sheet top cover fixed with steel screw for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for :- One light or fan point controlled by one single pole switch 5 Amps

One 5 Amps switch socket combination on independent board

One 5 Amps switch socket combination on same board with other switches.

All as per item No 3 here-in-before but with 2.5 sqmm size single core multistranded copper conductor cable for 6 pin 15 Amps switch socket combination outlet on independent board with 2.5 sqmm PVC insulated and unsheathed copper conductor as earth and connected to earth dolly.

Supply anf fix piano type switch 1-way 6 Amps, AC, 230 volts, single pole.

S/F Socket outlet 2 in 1, 3 pin, 5A, flush type piono Universal type,controlled by One Switch, conforming to IS and/or as approved, complete all as specified and as directed.

Supply and fix switch socket combination, universal type, 5 Amps 240 volts AC ISI marked 2-in-1 flush type 5 pin suitable for inserting 2 pin 5 Amps/ 3 pin 5 Amps plug top all as specified.

Supply and fix stepped socket type (5 step) electronic fan regulator flush type,upto 120 Watts 230 V. AC.

S & F ceiling rose surface bakelite three terminal of size 65X50mm,240 Volts AC PVC Polycorbonate isolated body complete

Supply and fix 34 watt LED Light aesthetically designed 1x1, 2x2 & 4x1 LED flat panel for surface mounting which provides soft-light and glare free symmetrical illumination complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size. Make- Havells Model No VENUSNEOHE 2X2 PLR 36 WLED8XXS or equivelent make of Bajaj /CG/ Phillips

Supply and fix LED tube light fitting of 18 watts 6000K , 230 volt, with long lasting pvc body with slim & sleek looks all pre-wired fixed on walls with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Make : Havells Philips/ Crompton Greaves/Bajaj

S&F in replacement LED tube light fitting of 20 watts 6000K , 230 volt, with aluminium extruded channel powder coated with diffuser for glare free light complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Make : Shakti/Crompton Greaves/Bajaj

M & L Sub main wiring with two runs of 4 sqmm (Nominal area) single core cable FRLS PVC insulated, multistranded, unsheathed, copper conductor cables 1100 Volts grade drawn through and providing (new) non metalic PVC rigid conduits (Medium grade) of suitable size including all accessories, fixed to wall/ceiling etc including 4 sqmm (nominal area) single core, FRLS PVC insulated, multistranded, unsheathed, copper conductor as earth wire and duly connected to to common earth point and to existing main switch/ distribution board of each building/ quarter complete all as specified and as directed by Engineer-in-charge.(Note : (a) PVC Conduits, two run cables and one run of earth wire will be measured as one length. (b) All incoming and outgoing cable shall be connected by using proper lugs & sockets.)

S & F Switch socket combination, 2 in 1, 5/15 Amps, 5 in 1 240 volts, flush type complete all as specified and directed.

S & F Factory made board distribution (DB) Double Door in sheet steel enclosure with common bus bar at incomming end, SPN, 8 way , 240 Volts , 200 amps suitable for housing MCBs, fixed flush in wall surface complete all as specified and directed. Make: LEGRAND/ABB/SIEMENS/ Havells / Standard)

S & F MCB, SP, 240 Volts, 6 to 32 Amps, 'C' Series, 10KA capacity complete all as specified and directed. (Make: LEGRAND/ABB/SIEMENS as approved)

S & F MCB, 'C' Series, SPN, 240 Volts, 06 to 32 Amps, 'C' Series, 10KA capacity complete all as specified and directed. (Make: LEGRAND/ABB/SIEMENS as approved)

Supply & Fixing 5 star rated energy saving ceiling fan 1200mm sweep (white) with all accessories and hanging the ceiling fan from fan hook with 3 core flexible copper wire 24/0.20 sqmm from ceiling rose, etc all as directed. Make : Model ES-50 of Havells or equivalent in Usha/Orient.

Supply and fix exhaust fans AC single phase 230/ 240 V of size 230 mm sweep with louver and require size of hole for exhaust fan Make Havells

Fan clamp fabricated out of 40x6mm MS flat fixed on angle iron/truss/GI Tubing with bolts, nuts, rubber bushes and washer etc complete suitable to fix ceiling fan including painting the exposed steel surface with two coats of first quality synthetic enammeled paint all as specified and directed.

M & L Earthing complete with GI earth plate electrode 600 mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with the top edge of earth plate at depth not less than 1.5 m below ground level using galvanised earth strip 32 x 6mm thick by means of bolts, nuts, check nuts and washers protected by 40mm bore light grade GI pipe connected toDB/Panel/Equipments, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, pre-cast RCC 1:2:4 type B-1 cover slab of size 300x300x50mm reinforced with 8mm dia TMT steel bars @15cm centre to centre in both direction and 10mm dia MS handle of suitable size, charcoal or coke and common salt in alternative layers,necessary earth work in hard soil all as shown in Electrical Plate No 3 of MES Schedule Part I and testing complete including taking down old one as specified and as directed.

Srisrinivasaenterprises

Sangam Construction