Construction of 2-Lane ROB on Kurukshetra Narwana Railway line at LC no. 40 Km. 49/4-5 on Thansar Dhand Kaithal road MDR-119 Distt. Kaithal (Pdg. Street Light only)

Amount

Supply and erection of PVC copper insulated and sheathed 2-core circular flexible wire. 31.9 (i) d Size 1.50 sqmm ( 48 / 0.20mm).

31.9 (i) e Size 2.50 sqmm ( 80 / 0.20mm).

Supply and erection of moulded case circuit breakers on wall or on existing pedestal including bonding to earth and necessary connections. 31.12 c (i) 15 amp.to 60 amp. 415 V ,10 KA 3-phase.

Supply and erection of miniature circuit breaker / isolator 240 /415 V in the existing distribution board including making necessary connections. 31.17a) (ii) SP MCB of 9 KA breaking capacity 6 amp. to 32 amp.

31.17(a) (ii) TPN MCB of 9 KA breaking capacity 6 amp. to 32 amp.

31.17(a) (iii) TPN MCB of 9 KA breaking capacity 40 amp. to 63 amp.

Supply and erection of pipe for wiring purposes including bends inspection boxes etc. where necessary and painting as required. 31.21 (xii) Galvanised iron pipe 40 mm dia on flushed.

31.21 (xiii) Galvanised iron pipe 50 mm dia on flushed.

Galvanised iron flexible pipe complete with socket nipples and checknuts etc. at both ends ( upto length of 1 metre.) 31.21 (xxvii) (e) Size 40 mm dia.

31.22(i) Earthing with GI earth pipe 4.5 m long and 40 mm dia with masonry enclosure on the top etc. as required .

31.22(ii) Extra for using salt and charcoal / coke for pipe earth electrode as required.

31.22(xix) Supply and erection of 20 mm x 3 mm thick G.I. tape fixed with suitable G.I. stapples of same size.

Supply and erection of under ground cable ,loose in existing pipe or trenches complete with necessary connections . 31.26 (xI) Ard. 16 Sq. mm 4 Core Cable .

31.26 (xIi) Ard 25 Sq. mm 4 Core Cable .

31.26 (xIiii) Ard. 50 Sq. mm 4 Core Cable .

Supply and erection of suitable compression type brass cable glands for underground Cable. 31.28 (ii) 10 Sqmm to 16 Sqmm Cable 2 to 4 Core .

31.28 (iii) 25 Sqmm to 50 Sqmm Cable 2 to 4 Core.

31.33 (iv) Supply and erection of Godrej Almirah typeM.S.pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S.sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- M.S.pedestal of size 900 mm wide , 1500 mm high , 450 mm deep and bottom totally open , duly embeded in cement concrete block of size 1050 mm x 600 mm x 200 mm above ground level duly plastered with 12 mm thick 1:4 cement plaster ,having a base of size 1200 mm x 750 mm x 250 mm below ground level .

31.40 Supply and erection of PVC unsheathed copper conductor cable single core 1100 volts grade in pipe of suitable size excluding cost and erection of pipe . Size 6 sqmm ( 7/1.05 )

Size 10 sqmm ( 7/1.35 )

31.41 Supply and erection of Double door sheet steel enclosure distribution boards suitable for MCB's & ELCB's recessed in wall including bonding to earth complete with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4-way , TP&N ( Horizontal) (8+12)

31.67 S/E of mark double walled corrugated (DWC) HDPE pipe laid 1 mtr. below ground level including diging and refilling of earth including cost of suitable size socket / cuppler for HDPE pipe including the cost of labour and material required to complete the job in all respect upto the entire satisfaction of Engineer-incharge of the work HDPE pipe 90 / 75mm outer dia / inner dia.

31.68 Supply & Erection of Hot Dip Galvanized octagonal pole of 3 mm thickness, with base plate including cost of nut and bolts and all accessories as supplied by the manufacturer including cost of foundation accessories etc. The foundation bolts as per manufacturer design should be hot dipped galvanized pole complete with door locking arrangement. Terminal plate consisting of 2 Nos. 100A. 4 pole natural links including connection etc. with suitable connecting arrangment for 2 no. MCBs / kit kat including cost of R.C.C. 1:1.5:3 for foundation of size 0.7 M. x 0.7 M. x 1.8 M with minimum 8 Nos. 12mm dia longitudinal MS reinforcement rods with rings of 8 mm dia not more than 200mm C.C. for fixing the pole with all labour & material required to complete the job in all respect upto the entire satisfaction of Engineerin-charge of the of the work. 9 Mtr. Long pole with top dia 70mm and botom dia 155mm with base plate of size 260 x 260 x 16mm.

31.69 Supply and erection of module case circuit breaker single pole/ 4 pole on wall /on existing pedestal including bounding to earth and making necessary connection required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 6 amp to 63 amp

31.76 Supply and erection of metal clad bus bar chamber made from 1.6 mm thick M.S.sheet fixed with rag bolts on wall or on existing pedestal / angle iron frame including bonding to earth Copper bars 63 amp. 415volt 4 bars of 325mm each (Cross section 20x3mm) duly tinned over all size of the chember 375mmx295mmx140mm.

31.83 (i) Supply, installation, Testing and commissioning of 12.5 Mtr. long High Mast manufactured from B.S.E.N. 10025 or equivalent grade material in, 2 (two) section hot dip, galvanized inside and outside in single dip, suitable for wind velocity as per IS 875 Part-3 suitable for 6 Nos. Luminaire loading fully motorized with starter & cable complete along with standard accessories supplied by the manufacturer with 3 nos. steel wire rope double drum system and twin dome aviation light with LED without foundation but including cost of set of foundation nut and bolts, installation at site complete in all respeect upto entire satisfaction of Engineer-in-Charge. Thickness of Top Section = 3mm (Minimum) Bottom Section =3mm (Minimum) Top Dia = 150mm Bottom Dia = 360mm Thickness of Galvanization Top = 65micron (Min.) Bottom = 85micron (Min.)

31.83 (ii) Supply, installation, Testing and commissioning of 16 Mtr. long High Mast manufactured from B.S.E.N. 10025 or equivalent grade material in, 2 (two) section hot dip, galvanized inside and outside in single dip, suitable for wind velocity as per IS 875 Part-3 suitable for 6 Nos. Luminaire loading fully motorized with starter & cable complete along with standard accessories supplied by the manufacturer with 3 nos. steel wire rope double drum system and twin dome aviation light with LED without foundation but including cost of set of foundation nut and bolts, installation at site complete in all respeect upto entire satisfaction of Engineer-in-Charge. Thickness of Top Section = 3mm (Minimum) Bottom Section =4mm (Minimum) Top Dia = 150mm Bottom Dia = 410mm Thickness of Galvanization = Top = 65micron (Min.) Bottom = 85micron (Min.)

NS ITEMS S&E of single arms bracket made of 50mm dia GI pipe B class 1.25 mtr. Long with 25mm dia bottom pipe GI with coller pipe (GI) 75 mm dia 60cm Long with MS nipple as required for fixing of fitting duly welded at end of bracket top covered with ornamental cap duly welded, painted 2 coats of aluminium paints on bracket and golden paint of ornamental cap including the cost of labour and petty material etc. complete in all respect upto the entire satisfaction of Engineer-incharge. G.I. Single Arm Bracket

G.I. Double Arm Bracket

Supply and erection of single arm bracket made of 40mm dia GI pipe B class ISI 1.25 mtr. Long with GI clamp for fixing the pipe on octagonal pole with suitable size of nut and bolts with painted 2 coats of aluminum paints on bracket and including the cost of labour and petty material etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge

Supply, erection and commissioning of Timelite 40A. 3 pole / 230V Digital time switch Indo Asian make automatic Timer ON/OFF the street light, pillars, wall, MS pedestal where ON/OFF point is available cabinet is fabricated from 22 gauge MS sheet painted, wiring, connection ON/OFF from the bottom of the cabinet the lite DB IP 54 protection complete with Digital timer, 32A. TPN MCB (Indo-Asian), fuse unit, indication lamp suitable for switch from rectifier system, switching system Bakelite connector 32A. Digital timer, auto / manual system, time setter, fiber sheet rubber & plastic components, wiring & component fitting, chemical (Epoxy) including the cost of labour and petty material etc. complete in all respect upto the entire satisfaction of Engineer-in-charge of the work.

S.E.T.C. of 90W LED Street Light Luminiares of Make Bajaj/ Crompton/ Philips with pressure die cast aluminum housing with lens and accessories required to complete the job in all respect including erection on existing pole for fixing including connection of the same upto the satisfaction of Engineer-in-Charge of the work

Supply and erection of 150W LED Flood light Luminaires with Pressure die cast aluminium housing with lens and accessories required to complete the job in all respect including erection on existing pole for fixing including connection of the same upto the entire satisfaction of Engineer in Charge of the work. (Make as per approved list).

Supply and erection of CT operated electronic energy meter with CTs of required ratio duly erected wired tested from UHBVN laboratory including necessary testing fees and petty material installed in MS box of 16G complete in all respect all items of make specification and size as approved by UHBVN.

Construction of RCC foundation for 12.5 / 16 / 20 mtr. high mast complete in all respect as per the appended design including the cost of digging sand filling 6" lean concrete 1:8:16 / bricks souling, Bar binding cement concret (M-20) shuttering, fixing of foundation bolts, refilling, carrying and erection of High Mast on foundation including petty material to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work. (Foundation bolts and template to be supplied by department).

J.B.S.Electrical Co.

M R CONSTRUCTION COMPANY

malkhansinghelectricals

numac powertech