SPECIAL REPAIRS TO BLDG NO. T-292 AND T-300, PROVN OF CGI SHEET COVERING OVER PATH AND SHED FOR TROOPS AT TRANSIT CAMP, PROVN OF TILES AND EXHAUST FAN IN BLDG NO. T-230, PROVN OF STORE ROOM NEAR BLDG NO. T-58, PROVN OF CAFETERIA AND PROVN OF GUARD RO

Amount

B/R SERVICES/ WORKS

Demolition Cement Concrete (Un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and Removing Debris, etc. to a Distance exc. 50.00 Metre but not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Brick Work, Pre-cast Concrete Block Masonry, built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc. including Serviceable Bricks keep in Safe custody for Re-use at Site, complete all as specified and as directed.

Taking down Chowkat or Frame (without Taking Off Shutter from the Frame) of any description, not exc. 1.50 Square Metre Each, complete all as specified and as directed.

Dismantling Structural Steel Work of any description and from any Situations, complete all as specified and as as directed.

Dismantling Plain or Corrugated Steel Sheeting of any gauge and thickness, Seggregating Serviceable Steel Sheeting and keep in Safe Custody for Refixing, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards/ Slabs/ Blankets of any descriptions including Cover Fillets, complete all as specified and as as directed.

Dismantling Ceiling Frame (Snap Grid) with Hangers of any descriptions but except Wall and Ceiling Boards, complete all as specified and as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing) and Removing Debris, etc. to a Distance exc. 50.00 Metre but not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Cement Plaster including Raking out Joints, Hacking for Key, Scrubbing down with Water and Removing Debris, etc. to a Distance exc. 50.00 Metre but not exc. 100.00 Metre, complete all as specified and as directed.

Taking up or down Steel Tubing 15mm bore (dia) and Connections, Segregating the Serviceable Pipes and Connections, Stacking properly at Site(s) and Keep in Safe Custody for Re-use, complete all as specified and as directed.

Taking up or down Steel Tubing 20mm bore (dia) and Connections, Segregating the Serviceable Pipes and Connections, Stacking properly at Site(s) and Keep in Safe Custody for Re-use, complete all as specified and as directed.

Excavation in Trenches not exc. 1.50 Metre wide and not exc. 1.50 Metre in Depth for Foundation etc. or for Shafts, Wells, Cess Pits, Manholes, Pier Holes, etc. not exc. 10 Sqm on Plan and not exc. 1.50 Metre in Depth and getting out as in Soft/ Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering and Well Ramming in layers not exc. 25 Cm, in Soft/Loose Soil, complete all as specified and as directed.

Labour for Spreading and Levelling of soil otained from Excavation in layer n.exc. 25 cm thick including Well Ramming and watering as reuired complete all as specified and as directed.

Removing Excavated Materials (Soils), exc. 50.00 Metre and depositing where directed at a level not exc. 1.50 Metre above the Starting Point, complete all as specified and as directed.

Excavating in Post Holes (or Similar Holes) in Soft/Loose Soil, each not exc. 0.50 CUM, getting out and Removing surplus Soil to a distance not exc. 50.00 Metre and Making Good Surfaces, complete all as specified and as directed.

M&L Hardcore Broken Stone or Boulders, Gauge not exc. 63mm, Deposited, Spread and Levelled in Layers not exc. 15 Cm thick, Watered and Well Rammed to a True Surface, complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (20mm graded aggregates) in Foundations, Filling and Mass Concrete, etc. including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork will deemed to be included in the Quoted Unit Rate.

M&L Cement Concrete 1:4:8 (40mm graded aggregates) in Foundations, Filling and Mass Concrete, etc. including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork will deemed to be included in the Quoted Unit Rate.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregates) in Beams, Cantilevers, Bressummers, Lintels Over 1.50 Metre Span and the like, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured & Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregates) in Slabs supported on Walls, Beams and Columns in Floors, Roofs, Landings, Balconies, Canopies, Deck Slabs and in Shelves and the like, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured & Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregates) in Chajjas and the like, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured & Paid for separately under appropriate Items.

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick, Rough Finished Surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides and Soffits of Floor or Roof Beams, Girders, Beam Haunch-ings, Bress-summers, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc. also splays between Floors and Beams, etc., Flat, Rough Finished Surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Soffits of Chullah Hoods, Chajjas, Troughs and Similar Items including Edge, Rough Finished Surfaces of Concrete Flat, complete all as specified and as directed.

M&L Machine Made & Pressed Pre-cast Cement Concrete Block Masonry with Solid Blocks 300x200x200mm or 300x200x100mm in Sizes, having Compressive Strength of not less than 100 Kg/ Sq Cm (as per IS-2185) in Cement Concrete 1:3:6 (20mm graded stone aggregate), exc. 10 Cm in width and setting in Cement Mortar 1:6, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 40mm thick in Damp Proof Courses to Horizontal or Vertical Surfaces including Use & Waste of Formwork and Applying Evenly a coat of Blown type Bitumen @ 1.50 KG/SQM and blinding with Clean Dry Sand @ 0.05 CUM/SQM, complete all as specified and as directed.

M&L Cutting Holes in Brick/ Pre-cast Concrete Block Walling, not exc. Half Brick thick, built in Cement Mortar for inserting of Holdfasts, Lugs, etc. and Making Good to Dismantled portion with Cement Concrete 1:2:4 (20mm graded stone aggregates) or Cement Mortar 1:3 (as required) and Adjoining Surfaces in Cement Mortar 1:4, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Panelled Shutter 35mm thick (any number Panels) Plain, Framed with Lock Rails, having Panels of 12mm thick Veneered Particle Board medium density, Wood Particle Board with commercial Face Veneers and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 30mm thick, Open Rebated and Prepared to Receive Gauge, Glass, etc., Divided into Squares, with Plain, Chamfered or Rounded, Mitred and Rebated Sash Bars, any Numbers, Sizes of Members of Shutter as specified in SSR Part-I, Section 8, Clause 8.24(b) and fitted to Chowkat, complete all as specified and as directed.

S&F Solid PVC Door Frame of Size 50x47mm made out of 5.0mm thick Plain colour PVC Sheet Reinforced with Mild Steel Square Tube and fixing in Opening as per Specification and Drawing of MES Schedule, complete all as specified and as directed.

S&F Factory Made Solid Panel PVC Door Shutter 30mm thick (Style) consisting of Frame made out of Mild Steel Tubes for Top & Bottom Rails, Mild Steel Frame shall be covered with Heat Moulded Plain Color PVC ‘C’ Channel having a PVC Strip of 20mm width stuck inside with Solvent Cement for Stiles & Plain Color PVC Sheets for Top Rail, Lock Rail & Bottom Rail on Either Side & gap insert for Top Rail & Bottom Rail, Paneling of Plain Color PVC sheet to be fitted in the Mild Steel Frame, welded/ sealed to the Stiles & Rails with suitable PVC Sheet Beading & jointed together with Solvent Cement and fixing in the Frame with Butt Hinges as per Site as per Specifica-tion and Drawing of MES Schedule, complete all as specified and as directed. NOTE : Builders Hardware will be Measured & Paid seperately under appropriate Items.

S&F Aluminium anodised Barrel Tower Bolt, 150mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt, 200mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy anodized, Sliding Door Bolt 300mm long with Hasp Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Section and fixing Bolts and Sliding Bolts of Extruded Section, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of Size 100mm, complete all as specified and as directed.

S&F Aluminium anodised Handle of Size 150mm, Cast type, complete all as specified and as directed.

S&F Mild Steel 300mm, Ordinary Rat Tail Rod pattern Springs including Roller and Roller Plate, complete all as specified and as directed.

S&F Galvanized Mild Steel Wire Cloth 0.56mm nominal dia of Wire and average width of aperture 1.18mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed.

S&F Sheet Glass 3.0mm thick, Plain, Ordinary quality and Glazing with Steel Pins/Clips in Square not exc. 0.50 Sqm in Each Pane to Steel Windows, complete all as specified and as directed.

M&L TMT Bars 10mm dia and Over, Cut to length, Bent to Shape required including Cranking, Bending Spirally for Hooping for Columns, hooking Ends and Binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8.0mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Framed Work in Doors or Gates of Angle or Other Section with Gusset Plates, Rails, Braces, etc., complete, drilled for fixing of Steel Sheeting or Other Covering. Doors, etc. to be prepared for Hanging or Sliding with and including either Hooks and Hinges or Steel Hanging Door Fittings (exclusive of Steel Sheeting or Other Covering, Running Rails and Guides) and Hanging; also Fastening and fixing, conforming to Fe-290, Gde E-165, complete all as specified and as directed.

M&L Mild Steel Framed Works such as Grills, Gratings, etc. with Ends of Bars shouldered and/or riveted or forged into Spikes; Framed Guard Bars; Barred Iron Doors; Ladders; Framed Balusters; Walkways; Railings; Framework of Water Tanks and similar Work, conforming to Fe-290, Gde-E-165, complete all as specified and as directed.

M&L Mild Steel Bands, Straps, Supports or Stays for Rain Water, Ventilating Pipes including Bolts (if required), Heavy Hooks (Stay) for Large Gates; Hook and Pintle Hinges, Large Hasps and Staples; Chains; Hand Made Sliding Bolts; Clamps; Holdfasts (Flat Iron 25x4.0mm); Wall Ties; Hooks for Hanging Fans; Plain Angle Cleats for securing Purlins to Wood Trusses or Rafters; Knee Piece inserts; 2-way and 3-way Straps, Plate Washers and Similar Small Articles, conform to Fe-290 Gde-E-165, complete all as specified and as as directed.

M&L Rolled Mild Steel Sections in Joist, Channel, Angle, or Tee Sections in Vertical Post, fixed independently, without Connecting Plates, etc. (cut to ordinary Lengths i.e. within 20mm of the Length indicated), conforming to Fe-410-W (Gde E-250) Quality 'B', complete all as specified and as directed.

M&L Rolled Mild Steel Sections in Main and Cross Beams, Hip & Jack Rafters, Purlins where connected to Common Rafters, Running Rails and Guides for Sliding Doors, conforming to Fe-410-W (Gde E-250), Quality 'A', fixed with Angle Cleats or Other Connecting Plates, complete all as specified and as directed.

M&L Mild Steel Tubular Trusses including Special Shaped Washers, etc. complete using ERW or Induction Butt welded Tubes, confirming to IS:1161-1979, Grade St-240, complete all as specified and as directed.

S&F Factory made Steel windows with side Hung Shutters including Box Type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F Factory made Steel windows with side Hung Shutters including Projecting Type Hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and as directed.

S&F Corrugated Mild Steel Sheeting 0.63mm thick, Galvanised @ 275 Gram Per Sqm, with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Plain Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Ridges/Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

M&L Aluminum Anodised Snap Grid/ Frame Work of Size 605x605mm in Ceiling, all as per Specification and Drawing of MES Schedule (except Hangers), complete all as specified and as directed.

S&F Hangers 4.0mm dia GI (upto 1200mm length) for adjusting Level, fixed to Roof Slabs by means of Ceilling Cleats made out of GI Flat 40x3.0mm in Size, 60mm long and Expansion Hold Fasteners 12.5mm dia, 40mm long, complete all as specified and as directed.

S&F HSPC Non-Asbestos Fibre Cement Building Boards 595x595x6.0mm thick, Pre-primed, Self Embossed, Textured Designer Boards, Water Resistant, Termite Resistant, Fire Resistant for insulation, fixed or laid/ inserted to Aluminum Snap Grid Frame Work with Screws, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 75mm thick in Sub-base to Floor, etc., complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 25mm thick in Sub-base for laying of Tiles, etc. including maintaining Level Uniformly, finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Chequered Cement Concrete Coloured (Terracota Red) Tiles 200x200x25mm thick, Set and Jointed in Neat Cement Slurry in Floors and Pointed in Grey Cement, laid over and including 20mm thick Cement Screed Bed in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Screed Bed will deemed to be included in the Quoted Unit Rate.

M&L Roughening Surfaces of old Concrete Floor by picking, sweeping clean and washing down with water to remove dust and Brushing neat Cement slurry with 3.0kg of cement per square metre complete all as specified and as directed.

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm (1st quality and/ or as approved) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Screed or Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Screed Bed will deemed to be included in the Quoted Unit Rate.

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm (1st quality and/or as approved) in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Screed or Screed Bed 15mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Screed Bed will deemed to be included in the Quoted Unit Rate.

M&L Vitirified Ceramic Tiles 10mm thick (Square/Rectangular) in Light shade, Polished, area of each Tile not exc. 0.36 Square Metre in Floors, etc., Set and Jointed in Neat Cement Slurry and pointed in White or Coloured Cement to match the Tiles, laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Screed Bed will deemed to be included in the Quoted Unit Rate.

M&L Glazed Ceramic White Tiles 300x200x7.0mm thick (1st quality as approved) conforming to IS:13753 in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Screed or Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Screed Bed will deemed to be included in the Quoted Unit Rate.

M&L Machine Cut Granite (of any type) Work 20mm thick (Table Rubbed and Polished) in Steps, Jambs, Pillars, Window Cills, Cooking Platform and like in Cement Mortar 1:4 including Pointing in White Cement 1:2, using Marble Dust with admixture of Pigment to match with Shade of Granite, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Screed Bed will deemed to be included in the Quoted Unit Rate.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregates) 75mm thick in Plinth Protection, etc, Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without Using Extra Cement, complete all as specified and as directed.

M&L Rendering in ceiling, 5mm thick in Cement Mortar 1:3 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering (Internal) 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering (Internal) 15mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering (External) 15mm thick on Bricks/Pre-cast Blocks or Concrete Works consisting in 2 layers, Backing/Under layer of 10mm thick in Cement Mortar 1:4 and Float/Top layer 5.0mm thick in Cement Mortar 1:4 including mixing WPC to Float/ Top layer, finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured & Paid separately under appropriate Item.

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Ceiling and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing Old Treated Plastered Surfaces of Walls and applying One Coat of White Wash, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Wall Care Putty 1.5mm thick on Plastered Surfaces of Walls including Cutting and Rubbing down to obtain an Even and Smooth Surface, complete all as specified and as directed.

M&L Applying Two Coats of Distemper Oil Emulsion (as approved) over a Coat of Chalk Whitening (Priming Coat) on Putty Finished Surfaces, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint (of approved Tint) over a Coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing Old Decorated/Treated Plastered Surfaces of Walls and applying One Coat of Cement Base Paint (as approved Tint), complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, Over 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/grade Paint of approved Tint) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

S&F Galvanised Steel Tubing 15mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F Galvanised Steel Tubing 20mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia) Cast Copper alloy, Chromium Plated, Fancy type with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule and Fixed-in-repairs, complete all as specified and as directed.

S&F Pillar Tap 15mm bore (dia), Cast Copper alloy with Capstan Heads, Chromium Plated, Fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed Shanks and Fly-nuts, screwed for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F Stop Cock/Valve (Straight or Angular) 15mm bore (dia), Cast Copper alloy, Chromium Plated, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions and Fixed-in-repair, complete all as specified and as directed.

S&F Vitreous China White One Piece Wash Down Water Closet Pan (Pedestal Pattern) with PVC (SWR) ‘P’ or ‘S’ Trap, Plastic Seat and Cover Fixing Bolts and Making Good to Floor/ Distrubed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed.

S&F Hand Shower (Health Faucet) with Wall Hook, Brass Chromium Plated having 1.20 Metre long with PVC Hose Pipe and Fixed-in-repairs, complete all as specified and as directed. MAKE : JAQUAR ALD-CHR-593 or equivalent Model in Make : GEM/ MARC (as approved by GE)

S&F Vitreous China White Wash Hand Basin of Size 550x400mm, with Pedastal, Flat Back including Brass Chromium plated Waste Fitting 32mm bore (dia) and PVC Waste Pipe 32mm bore (dia) of Low or High density, a Pair of Cast Iron Brackets or Erecting Stand duly Painted, Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 but excluding Taps, Chain, Plug & Porocelain Stopper and Fixed-in-repairs, complete all as specified and as directed.

S&F Vitreous China White Urinal, Full Stall type (excluding Flushing Cistern, Flush Pipe and Waste Pipe) including Providing and Fixing Plugs, Bedding Urinals against Wall in Cement Mortar 1:2, securing Urinal to Plug with and including 60mm long Brass Chromium plated Screws, Pointing around Urinal back in Cement Mortar 1:3, fixing Urinal Spreder of Brass Chromium plated, Flush Pipe, Grating and Union for Discharge Pipe (but Exclusive of fixing Supply Pipe to Flushing Cistern, Trap and Waste Pipe) and Fixed-in-repairs, complete all as specified and as directed.

S&F PTMT Waste Coupling of Size 32mm having Minimum Weight 45 Gram (Half or Full threaded) and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC Waste Pipes 32mm/40mm bore (dia) suitable for Wash Hand Basin, Sinks, Urinals, etc. and Fixed-in-repairs, complete all as specified and as directed.

S&F High Density Polyethylene Pipes (HDPE) 50mm bore (dia) of Pressure ratings 6.0 Kg/Sq Cm and fixing to Walls, Ceiling or in Floors, etc. and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC Connection Pipe 15mm in Size and 450mm in length with PTMT Nuts and Fixed-in-repairs, complete all as specified and as directed.

S&F PTMT Grating Doom of Size 100mm having Minimum Weight 25 Gram (as approved) and Fixed-in-repairs, complete all as specified and as directed.

S&F PTMT Urinal spreader having Minimum Weight of 60 Gram of any colour for fixing with 15 mm dia pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F Tubular Towel Rail 20mm dia, Brass Chromium Plated, D-type, 60 Cm long between Flanges with Bracket (One Pair) and Fixed-in-repairs, complete all as specified and as directed.

E/M SERVICES/ WORKS

M&L Taking down carefully Copper/Aluminium Point Wiring (Light/Fan, Socket or Power) complete from in any position including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets (but excluding Light Fittings of any descrip-tion), etc., Making Good Disturbed Surfaces of Walls/Ceillings, etc. in Cement Mortar 1:3 including Providing Surface Treatment (Colour Washing/ Distempering/ Painting) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable (Green colour) as Earth Continuity Wire, drawn in SURFACE/ CONCEALED PVC Conduit, heavey duty (HMS grade) of suitable Dia/ Size alongwith all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddle, etc. complete with GI Terminal Box not less than 1.5mm thick, fixing Flush to Wall Surfaces, covered with 3.0mm thick Plastic laminated Sheet Cover and/or Modular Plates of suitable Size for mounting Switches, Sockets, Fan Regulators, etc., Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated Unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated Unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable (Green colour) as Earth Continuity Wire for ONE 6 AMP 5 PIN SOCKET OUTLET POINT on SAME BOARD, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable (Green colour) as Earth Continuity Wire, drawn in SURFACE/ CONCEALED PVC Conduit, heavey duty (HMS grade) of suitable Dia/ Size alongwith all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddle, etc. complete with GI Terminal Box not less than 1.5mm thick, fixing Flush to Wall Surfaces, covered with 3.0mm thick Plastic laminated Sheet Cover and/or Modular Plates of suitable Size for mounting Switches, Sockets, Fan Regulators, etc., Earth Continuity Wire connected to Common Earth dolly for ONE 6 AMP, 3/5 PIN SOCKET OUTLET on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH Multi-stranded Single Core Copper Conductor Cable (Green colour) as Earth Continuity Wire, drawn in SURFACE/ CONCEALED PVC Conduit, heavey duty (HMS grade) of suitable Dia/ Size alongwith all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddle, etc. complete with GI Terminal Box not less than 1.5mm thick, fixing Flush to Wall Surfaces, covered with 3.0mm thick Plastic laminated Sheet Cover and/or Modular Plates of suitable Size for mounting Switches, Sockets, Fan Regulators, etc., Earth Continuity Wire connected to Common Earth dolly for ONE 16 AMP, 6 PIN SOCKET OUTLET on INDEPENDENT BOARD, complete all as specified and as directed.

S&F Rigid Non-metallic PVC Conduit of Size 20mm (External Dia) exclusive of Boxes (Junction/ Terminal) but inclusive of all Tees, Bends, Elbows, Reducers, Bell Mouth Tube Ends and Fixing Accessories such as Couplers, Lock Nuts, Saddles, Pipe Hooks, etc. including Taking down/ out Unserviceable PVC Conduit Pipe, complete all as specified and as directed.

S&F PVC Rectangular Block of Size 350x300x50mm Deep with 3.0mm thick Plastic Laminated Sheet Cover for mounting Swiches, Sockets, Fan Regulators, etc. including Taking down/ out Unserviceable PVC Block, complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, Flush type, 1-way, 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F Socket Outlet 6 Amp, 3 Pin, 2-in-1, Flush type, 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6 Amp, 5 Pin, Multi-plug, Flush type, 230 Volt AC, complete all as specified and as directed.

S&F Switch Socket Combination 6/16 Amp, 5 Pin, Multi-plug, Flush type, 230 Volt AC, complete all as specified and as directed.

S&F Lamp Holder PVC/ Polycarbonate type with Back Plate suitable for Batten Fitting and connecting up, complete all as specified and as directed.

S&F Ceiling Rose 65x50mm, 3 Terminals, Surface Bakelite suitable for 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F Ceiling Fan Regulator 230 Volt AC, Rotary Stepped Electronic type 120/280 Volt and Connecting up, complete all as specified and as directed.

S&F LED Bulkhead Light Fitting 1x10 Watt, Decorative including LED Light, Driver, Holder, connecting up with and including Flexible Copper Conductor Cable, 3 Core of suitable Size and Length, including Taking down/out Old Unserviceable LED LIGHT FITTING (04 Nos Only) of any description complete all as specified and as directed.

S&F LED Light Fitting (T8) 1x20 Watt, 220 Volt, AC Decorative Box type with Driver, Holder, LED Tube Light and connecting up with and including Flexible Copper Conductor Cable, 3 Core of suitable Size and Length, including Taking down/out Old Unserviceable LED LIGHT FITTINGS (06 Nos. Only) of any description complete all as specified and as directed.

S&F LED Luminaire 600x600mm, 36 Watt, 220 Volt AC Recessed type with High efficiency PMMA Diffuser Soft Glare Free Light complete with Driver, Holders, LED Lamp suitable for Roof Ceiling, Connecting up with 3 Core Flexible Copper Conductor Cable of suitable Size, complete all as specified and as directed.

Supply & Hanging BLDC Ceiling Fan 1200mm Sweep, Min Air delivery 210 CFM and Service Value 6.0 BEE, 5 Rated having 3 Blades, Holding Down Rod and Accessories, 230 Volt, Providing Electric Connection from Ceiling Rose to Ceiling Fan with and including Twisted Flexible Copper Conductor Cable of suitable Size and Length, 3 Core, complete all as specified and as directed.

M&L Cutting Holes in Brick Walls or Pre-cast Cement Concrete Block Masonry Walls of appropriate Size for fixing of Exhaust Fan including Making Good to Disturbed Portion/Surfaces of Walls/ Floor/ Ceiling, etc. with Cement Mortar 1:3 and Applying Surface Treatment (White/ Colour Washing/ Distempering/ Painting) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Taking down Ceiling Fan/ Exhaust Fan of any Make/Model/Sweep from any Height after disconnecting Electric Connection and Keep in Safe Custody for Re-hanging/ Re-fixing and Repairing, complete all as specified and as directed.

M&L Opening Body of Ceiling Fan 1200mm Sweep in presence of JE-in-Charge/ Engineer-in-Charge, Checking for Repair Works involving, Transporting Ceiling Fan from AGE E/M Store Yard at ALONG to nearest Workshop, Taking out carefully burnt out Winding of any type from the Fan of any Make, Cleaning of Slots, Rewinding Fan Motor with Super Enamalled Copper Wiinding Wire of suitable Gauge and Weight (not less than 350 Gram) providing New Insulation Materials, Varnishing, Heating, Reassembling & Testing for Smooth Functioning after Rewinding, Removing the Fan to Site of Work after Rewinding, complete all as specified and as directed.

M&L Preparing Old Painted Surfaces of Ceiling Fan/ Exhaust Fan including Cleaning, Washing, Rubbing and Filling Cavities with Filler, applying One Coat of Synthetic Enamelled Paint (as approved) with Spray Painting Machine and Writing MES No. with Black Paint, complete all as specified and as directed.

M&L Re-hanging only Ceiling Fan or Re-fixing only Exhaust Fan (Serviceable Ceiling Fan/ Exhaust Fan obtained from BOQ Item No. 2.016 here-in-before after repaired) and Connecting up with and including suitable Size Copper Conductor Cable from Ceiling Rose to Connector of the Fan, complete all as specified and as directed.

S&F Metalic/ Steel body Exhaust Fan 300mm Sweep with Blades, Frame and Louvers, 1360-1400 RPM, 45 Watt, 230 Volt, 50 Hz, Copper Winding with Fixing Arrange-ments using Fastener, Providing Electric Connection from Ceiling Rose to Fan with and including Twisted Flexible Copper Conductor Cable, 3 Core of suitable Size & Length, complete all as specified and as directed.

S&F MCB 6 Amp to 32 Amp, Single Pole, 'C' Curve, 50 Hz, 10 kA, 240 Volt and Connecting up incluing Taking down/out Old Unserviceable MCB (10 Nos. Only) of any description, complete all as specified and as directed.

S&F MCB 40Amp, Single Pole & Neutral, 'C' Curve, 50 Hz, 10 kA, 240 Volt and Connecting upincluing Taking down/out Old Unserviceable MCB (02 Nos. Only) of any description, complete all as specified and as directed.

S&F Sheet Metal Enclosure for DB's when MCBs to be used 4-way, SPN, 240 Volt, Double Doors, IP-43 Protected, Epoxy Based Powder coated suitable for mounting MCB DP/ SPN as Incomer and MCB SP as Out-goings with 200 Amps rated Bus-bar, Neutral Bar, Earth Bar, Connecting Cable Links and Connecting up, complete all as specified and as directed.

S&F Sheet Metal Enclosure for DB's when MCBs to be used 8-way, SPN, 240 Volt, Double Doors, IP-43 Protected, Epoxy Based Powder coated suitable for mounting MCB DP/ SPN as Incomer and MCB SP as Out-goings with 200 Amps rated Bus-bar, Neutral Bar, Earth Bar, Connecting Cable Links and Connecting up, incluing Taking down/out Old Unserviceable MCB (02 Nos. Only) of any description, complete all as specified and as directed.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) Light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc. 150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of Size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing on Completion,including Taking down/out Old Unserviceable Earthing of any description (01 Nos Only) complete all as per specified and as directed.

Excavating in Trenches, not exc. 1.50 Metre Wide and Depth not exc. 1.50 Metre for Taking out/up and/or Laying of UG Cables, Water Pipes Lines, etc., Forming Surfaces to required Foundation, etc. and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering, Well Ramming in Layers not exc. 25 Cm, Providing Heaps along the Route of the UG Cables, Water Pipes Lines, etc. with Surplus Soil in Soft/Loose Soil, complete all as specified and as directed.

Supply, Laying & Testing XLPE insulated, Armoured, Heavy duty, Electric Cable with Aluminium Stranded Conductor, 1100 Volt grade, Cross-sectional Area 10 Sqmm, 2 Core, laid in Trenches/ Ducts or Passing through Pipe or Fixing on Poles, etc., complete all as specified and as directed. NOTE : Necessary Earthworks, Sand Cushioning, Bricks Protection, GI Pipe, etc. will be Measured and Paid separately under relevent Items.

M&L HDPE Double Wall Corrugated (DWC) High density Polythene Pipes of Outer dia 40mm and Inner dia 32mm, cut to length/Size as per Site requirement having Corrugation on the Outer Wall and Plain Surface on the Inner Wall, confirming to IS:14930 (Part I & II) for Protection of UG Cable/ in PCC with and including all Fittings as required at Site including Cutting Floor and Making Good the same to match the Existing/ Adjoining Surfaces, etc., complete all as specified and as directed. MAKE : REX POLY EXTRUSIONS (ELDREX) or equivalent (ISI marked). NOTE : The Cost of All Accessories for fixing of DWC Pipe along the Wall/ Roof/ Cable Trays will deemed to be included in the Quoted Unit Rate.

PARBIN SIDDIKI