SPL REPAIR TO BLDG NO T-321 (SINGLE OFFRS LIVING BARRACKS) OF 24 ROU AND SPL REPAIR TO RE-WIRING IN BLDG NO P-1 P-2 P-3 P-4 P-5 P-6 AND P-84 OF 177 MED REGT AT BIKANER MIL STN UNDER GE (N) BIKANER

Dismantling Asbestos cement Corrugated sheets in roof covering including ridges complete all as specified and directed by Engr-in-charge

Dismantling of existing false ceiling of boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed by Engr-in-charge

M&L for pre painted galvalume aluminium zinc cozting GI based corrugated steel Sheet high rib profile tile pattern of slaty color coated 0.5 mm thick of 550 Mpa Tensile strength sheets as in roof covering and fixed as per manufacturers instruction (design as app by Engr in charge complete all as spfd )

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-charge

S&F Composite cement ceiling board 4 mm thick in ( 595 mmX595 mm ) pannel designer ceiling pre finished conforming to IS 14862 type B cateogory three incl GI frame , grid work,hold fast,suspended with suspender along with holding down bolt complete . (Note: Ceiling board shall confirming to IS-14862 ,shall be fire resistant , Moisture resistant and ceiling shall be suspended with suspenter and adjuster)

Taking down cement plaster/terrazo finish on brick or stone wall etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-In-Charge.

M&L for 10mm thick Rendering in cement mortar 1: 6 on fair faces of brick work or concrete surfaces, finished even & smooth without using extra cement complete all as specified and directed by Engineer-In-Charge.

M&L for 15mm thick Rendering in cement mortar 1: 4 on fair faces of brick work or concrete surfaces, finished fair and even without using extra cement using integral liquid water proofing compound and complete all as specified and directed by Engineer-In-Charge. Note : WPC shall be measured and paid seperately.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 2mm thick wall care putty on new surfaces including preparation and complete specified and as directed by Engineer in charge.

M&L for Preparing new /old plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over 2 mm thick putty complete all as specified and directed by Engineer-In-Charge.

Supply only liquid water proofing compound ISI marked @ 200ml per 50Kg of cement content complete all as specified and directed by Engineer-In-Charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm thick Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in plinth protection, , finished even and smooth using extra cement , laid in panels including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight ccomplete all as specified and directed by Engineer-in-Charge.

M&L for Double charged Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match floor including Screed bed or bedding layer of mortar 20 mm thick for laying floor finishes complete all as specified and directed by Engineer-in-Charge.

All as above item No 14 but as in skirting over 10 mm cement screed bed backing ( 1:3) complete all as specified and directed by Engineer-in-Charge.

M & L for non skid ceramic colour (light shade) joint free tiles with matt finish size 400x400x7mm thick ( square/ rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed over Screed bed or bedding layer of mortar 20 mm thick for laying floor finishes confirming to IS-15477:2004 including necessary cutting as per site requirement complete all as specified and directed by Engineer - in - Charge.

M & L for glazed ceramic tiles (coloured) 450x300x7mm thick on vertical surfaces such as skirting, dado and risers to steps set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 10 mm thick rendering in Cement Mortars 1:4 on fair faces of brick work or concrete surfaces complete all as specified and directed by Engineer-in-Charge.

Dismantling of floor hearth or existing terrazo dado /flooring or tilles in bath .WC and kitchen /kota stone etc complete all as specified and directed by Engineer-in-Charge.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engineer-in-Charge.

S&F vitreous china premium/1st quality wall hung water closet with P trap white/ivory/off white including connection to drain (or out going pipe) and to flushing pipe, antisyphonagee pipe,etc., and incl. plastic seat cover as recommended by manufacturer for particular model closed pattern with flat bottom etc; and incl S&F of all necessary accessories set like rag bolts/gel gasket/hinges etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete all as specified and directed by Engineer-in-Charge. Make : Jaquar (Continental Series-CNS-WHT-963N or equivalent from Parryware/Hindware as approved by AO

S&F concealed flushing cistern of PVC 10 ltr. cap. with dual flushing system, valveless syphonic action type, with inlet/outlet, ball valve, float and including brackets and connection to pipe etc. and incl S&F of all necessary accessories/installation kit and 'S' type drain pipe connetion set for wall hung WC etc as recommended by manufacturer for fixing, packing and including S&F of actuator knob/flush plates and and taking down existing of any description/size complete all as specified and directed by Engineer-in-Charge. Make : Jaquar (Concealed Cistern-JCS-WHT-2400S, Flush Plate-JCP-CHR-812415) or equivalent from Hindware/Parryware as approved by GE

S&F health faucet with 8mm dia and 1.2 metre long flexible tube in chorme finish and wall hook including making connections and fixed in position complete all as specified and directed by Engineer-in-Charge. Make : Jaquar (ALD-573) or equivalent from Hindware/Parryware/Cera as approved by GE

S&F in repair vitreous china premium/1st quality wash basin (under counter), white/ivory/off white, size 580x430 mm including S&F all accessories as recommended by manufacturer and incl. brass CP bottle trap 32 mm with inlet and outlet screwed for pipe or connections incl all necessary accessories for fixing, packing, union and incl 32mm brass CP waste coupling and complete fixed in position in all respect as per manufacturer's instructions and taking down existing of any description/size complete all as specified and directed by Engineer-in-Charge. Make : Hindware (WHB-Garnet (Cat No.- 10080), Waste Coupling-Cat No.- F850023 (Economy Model), Bottle Trap-Cat No.- F850072 (Economy Model) or equivalent from Jaquar/Parryware/Cera as approved by GE

S&F single lever central Hole Basin Mixer 15mm bore dia with letter marked for cold and hot complete all as specified and directed by Engineer-in-Charge.

S & F in repair brass chromium plated bib cock long Nose body Fancy type with capstan screwed down for iron pipe 15 mm bore complete all as specified and directed by Engineer-in-Charge.

S & F in repair angle valve cock chromium plated fancy type half/full turn for iron pipe 15 mm bore screwed down high pressure, with capstan head, screwed both ends for iron pipe or for union complete all as specified and directed by Engineer-in-Charge.

S& F single lever High concealed diverter flow consisting of exposed part kit with operating lever , wall flange & button and concealed body ,cartdge sleeve and also including bath spout with flange chromium plated ,screwed down, high pressure all as specified make Cera:(exposed part F1018721, concealed part F4030101, bath Spout F1020661), Jaquar or equivalent in same Pattern

S & F repair PVC connection 15 mm size brass nuts of length 450 mm complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections 15 mm bore complete all as specified and directed by Engineer-in-Charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store as directed complete.

Supplying and laying of CPVC pipes of 20 mm outer dia SDR 11 & Plain CPVC SDR 11 fittings in trenches, wall complete all as specified and directed by Engineer-in-Charge.

Supplying and laying of CPVC pipes of 25 mm outer dia SDR 11 & Plain CPVC SDR 11 fittings in trenches, wallscomplete all as specified and directed by Engineer-in-Charge.

S&F male/female brass threaded adaptor(FTA/FBTA) complete all as specified and directed by Engineer-in-Charge.

S&F in repair triple layer Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity, hoisted and fixed in position including connecting up pipes complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of 20 mm bore (minimum weight 210 gms) complete.

S & F in repair gun metal glob or gate valve with iron wheel head , crewed for iron pipe of 20 mm dia fixed in repair complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed by Engineer-in-Charge.

S&F SS folding Tubular towel rack, 20mm dia, , 60cm long between flangess including all accessories complete all as specified and directed by engineer in charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and as directed by Engineer-in- charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed by Engineer-in-Charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 850 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules ofelasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made all as specified and directed .

All as per item No-42 above but single extruded & size of WPC Chowkhat/frame of size 65 x 100mm ditto

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm - 4 nos. per leaf (Table 6 of BIS 12817-2020) BIS marked. (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf as per table 1, dia of bolt 12mm as per BIS 15833. (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos. per leaf (d) Stainless Steel (304 Grade) Finished Sliding Bolt 300 mm - 1 no. per leaf, 16mm dia as per BIS marked clause 3(iii) of BIS 15834-2020. (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos. per leaf

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type glazed/gauge skelton door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws including S&F of stainless steel 304 Grade (natural finish) wire cloth, all as per direction of Engineer- In- Charge including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm - 4 nos. per leaf (Table 6 of BIS 12817-2020) BIS marked. (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf as per table 1, dia of bolt 12mm as per BIS 15833. (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos. per leaf (d) Stainless Steel (304 Grade) Finished Sliding Bolt 300 mm - 1 no. per leaf, 16mm dia as per BIS marked clause 3(iii) of BIS 15834-2020. (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos. per leaf (f) Stainless Steel (304 Grade) wire cloth fixing as per manufacture

S&F of Powder Coated aluminium frame (minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etccomplete all as specified and directed by Engineer-in-Charge.

S&F 300 mm, ordinary rat tail rod pattern springs of mild steel including roller and roller plate complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of new/old steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

M&L for Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples and complete all as specified and directed by Engineer-in-Charge.

Demolotion of brick work built in cement mortar including all quions arches pillars etc complete all as specified and directed by Engineer-in-Charge.

M&l for brick work with sub class B bricks straight or curved on plan exc 6m mean radius brick walls built in CM 1:6. complete all as specified and directed by Engineer-in-Charge.

S& F chromium plated soap dish Holder with round flange, fixed on wall with chromium plated brass screws and PVC plug complete all as specified and as directed by Engineer in charge.

S&F Corner glass shelf of size 300mmx200x150mm fancy type, toughned glass, with CP bracket and guard railing, fixed along wall with CP brass screws and PVC plug complete all as specified and as directed.

M&L for 25mm dia stainless steel chromium plated curtain rod incl bracket & knobs fixed in position complete all as specified and directed by Engineer-in-Charge.

Anti termite treatment of soil under existing floor using chemical emulsion one litre per hole, 300 mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors complete all as specified and directed by Engineer-in-Charge.

Anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed by Engineer-in-Charge.

Supply only 5mm thick Figured glass, pin head type and glazing with beads (either supplied with shutters or to be measured separately as supply only) in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed by Engineer-in-Charge.

Supply only 4.80mm thick Sheet glass , ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed by Engineer-in-Charge.

Removing building materials etc. i.e broken construction material, plaster and like to a distance of 7 km at a suitable location complete all as specified and directed by Engineer-in-Charge.

Mild steel framed work such as grills, gratings, tank staging etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing;frame work for water tanks, cooler stand and similar work conforming to Fe 290 Gd E-165 complete all as specified and directed by Engineer-in-Charge.

M&L steel work in tubular trussess/ purlins incl spl shaped washer etc. using ERW or induction butt welded tubes confirming to IS 1161-1979 grade St-240. complete all as specified and directed by Engineer-in-Charge.

S&F Mild steel bolts.exc. 5 cm length not exc. 10 cm length (machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends, each screwed end to be fittied with washers and one hexagonal or square nut 11 to 15 mm neck dia complete all as specified and directed by Engineer-in-Charge.

M&L for mild steel work as in plates / flats angles etc as in cleats drilling welding etc complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) 110mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) 75 mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in Fixed in wall complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) vent cowl for 75mm dia pipe all as specified.

S&F PVC (SWR) diminishing pieces or tapers/ Reducers/ Sockets 110 mm bore fitted with oval access doorcomplete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) bends any radius 75 mm fitted with oval access door complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) bends any radius 110mm fitted with oval access door complete all as specified and directed by Engineer-in-Charge.

S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

S&F 50mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. .

S&F stack clamps out of 100mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to walls for 100mm/75mm bore pipe complete all as specified and directed by Engineer-in-Charge.

S&F for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

S&F stain less steel peg set with 06 no of hooks mounted on SS plate 4 mm thick with and including screws complete all as specified and directed by Engineer-in-Charge.

M&L Chequered cement concrete tiles30cmx30cmx25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and no pigment complete all as specified and directed by Engineer-in-Charge.

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in loose/soft soil complete all as specified and directed by Engineer-in-Charge.

Providing precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary moulds and setting in cement mortar 1:4 complete (reinforcement to be measured separately)

M&L for TMT bars 10mm dia and over , cut to length, bent to shape required, including cranking, bending spirallyfor hooping for columns, hooking ends and binding with and including ms wire (annealed) nit less than 0.90 m dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

Demolition and breaking up drain pipes (SGSW, AC or RCC) of internal dia__150__mm, set in cement mortar complete all as specified and directed by Engineer-in-Charge.

M&L for Cement concrete 1:3:6 type C2 Concrete bed(width of bed is outer dia of pipe plus 30 cm) to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed by Engineer-in-Charge.

M&L for DWCPE (SN8) confirming to IS-16098,150 mm Nominal bore (160 mm OD) complete laiding and jointed incl testing along with necessary jointing material tees /union /socket etc complete as per manufacture instructions and complete all as specified and directed by Engineer-in-Charge.

Cutting into existing manholes for connecting new drains, _150___mm bore, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required complete all as specified and directed by Engineer-in-Charge.

Demolotion of brick work built in cement mortar including all quions arches pillars etc complete all as specified and directed by Engineer-in-Charge.

M&l for brick work with sub class B bricks straight or curved on plan exc 6m mean radius brick walls built in CM 1:6. complete all as specified and directed by Engineer-in-Charge.

M&L for Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in lean concrete foundation complete all as specified and directed by Engineer-in-Charge.

M&L for 15mm thick Rendering in cement mortar 1: 4 on fair faces of brick work or concrete surfaces, finished fair and even without using extra cement complete all as specified and directed by Engineer-in-Charge.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed by Engineer-in-Charge.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete.

Taking down carefully (aluminium) point wiring complete of any type (batten/ surface conduit or concealed) for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants, ceiling rose, round block etc complete and making good disturbed surfaces of wall, floor or ceiling with plaster of tiles or roof treatment etc and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete all as specified and directed by Engineer-in-Charge.

Taking down old U/S existing DB SPN 8 way & TPN DB 4 way including MCB/MCCB industrial plug socket of any capacity and any size and removing from site and making good the disturbed surface of wall etc complete all as specified and as directed.

Disconnecting and taking down unserviceable submain wiring form TPN DB to SPN DB and SPN DB 8 way to SPN DB 4 Way complete & removing U/S items from site complete all as directed by Engineer-in-Charge.

Taking out carefully earthing set complete of any type including earthing wire & removing U/S items from site complete all as directed by Engineer-in-charge. complete all as specified and directed by Engineer-in-charge.

One light/fan point (Ceiling Fan/Exhaust Fan) controlled by one switch

One multi pin socket 5/6Amps, Independent.

One 5/6 amp socket outlet on the same board controlled by another switch complete all as specified and directed by Engr-in-charge

All as per item No 93 here -in- before but for one 3 pin 15/16 Amps socket outlet controlled by one 15/16 Amps switch on independent board with 4 sqmm single core PVC insulated and and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) including 4 Sqmm single core PVC insulated and sheathed multistranded copper conductor FRLSH cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour complete all as specified and directed .

S&F switch Modular type, 5/6 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.

S&F switch Modular type, 15/16 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.

S&F socket outlet 3 Pin 5/6 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.

S&F socket outlet 3 Pin 6/16 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.

S&F ceiling rose, surface backelite , three terminal AC, 230 volt complete all as specified and directed by Engineer-in-Charge.

Taking down Ceiling fan,sealing cable end, dismantling blades of any make, any sweep deposited to the store yard of AGE E/M (N) Bikaner for further disposal off / BER complete all as specified and directed by Engineer-in-Charge.

Supply and hanging/fixing ceiling fan 1200mm sweep AC supply (input voltage range 120 to 280v), BLDC type, 5 star rated BEE and ISI marked, super enameled copper winding of 'B' class insulation, single phase 20 watt (+ 10%), PF 0.90 (MIN), air delivery of 220 CUM per min (CMM), 350 RPM (+ 10%), TEMP RISE 40 DEGREE MAX, without remote, with electronic regulator, 3 blades, down rod length of 60/72 inch including accessories, total harmonic less than 10%, 5 speed, hanging in position, including making connection wih and including flexible cord twin core twisted copper conductor of size 23/0.0076 from cealing rose to fan complete all as specified and as directed. Note :- (i) Sl No of cealing fan and GE office name shall also be writing on fan with red colour permanant marker. Cost for the same shall deemed to be included in quoted unit rate. Nothing shall be paid extra on this account.

Supply and fixing fan step regulator modular type,120W -2 module electronic socket type five step controlled 230V AC 50 Hz for complete all as specified and directed by Engineer-in-Charge.

Supply and fix Air Circulator fans 230 Volts single phase oscillating 600 mm sweep suitable for wall mounting complete all as specified and directed by Engineer-in-Charge.

Taking down LED tube light fitting, 1x 20 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge.

Refixing LED tube light fitting, 1x 20 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge.

S&F LED tube light fitting, 1x 20-22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Make : Philips-BN021 LED 20S PSU CW GR S2/ Crompton Greaves LDDR20-CDL Dazzle Ray / bajaj-BCLAB 20W

Supply and fixing LED flood light 100 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp.

Supply and fixing LED Bldg Security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engineer-in-Charge.

S&F GI bracket made out of 40 mm bore GI pipe light grade /medume grade, ISI marked, medium grade 1.2m long bent to shape suitable for fixing of street light fitting including with 2 Nos MS clamps made with 40x3mm flat iron, bolts, nuts, washers etc including two coats of synthetic enamel paint over one coat of zinc chrome primer and fixing on electric pole complete all as specified and as directed by Engr-in-Charge.

S & F double door, sheet metal enclosure, powder coated for MCB DB TPN DB 4 way fitted with neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as specified and as directed by Engr-in-charge.

S & F double door, sheet metal enclosure, powder coated for MCB DB SPN 8 way fitted with neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as specified and as directed by Engr-in-charge.

S & F MCB SP, 5-32 Amps , 240 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge.

S & F MCB SPN, 5-32 Amps, 240 volts, breaking capacity 10KA complete all as specified and directed by Engineer-in-Charge.

S & F MCB TPN 40-100 Amps, 240 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge.

Earthing complete with galvanised perforated steel pipe electrode, 40mm bore, medium grade, 2.5 metres length, buried directly and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected with earthing lead of 4mm dia galvanised iron or steel wire protected by provision of GI mediumgrade pipe 15mm bore including provision of concrete pit made with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4Kg/Sqm) and frame of angle iron 40x 40x6 mm and handle of 6mm dia MS bar made to shape, GI light grade 20mm bore pipe for watering perforated at bottom, 1.75meter long placed on top edge of earth plate, common salt & charcoal filling with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate No -2 of SSR 2009 Part-I and connecting to Lighting protection earth test points all as specifed and directed including testing on completion.

Taking down the old unserviceable Fan regulator from site complete all as directed by Engineer-in-charge.

Taking down Ceiling fan,sealing cable end, dismantling blades of any make, any sweep, and refixing after necessary repairing such as winding of motor, replacement of capacitor & ball bearing of ceiling fan, cleaning all dust & painting with existing colour synthetic enamel paint by spraying including filling cavities with filler,one coat including writing MES No. complete all as specified and directed by Engr-in-charge

Taking down Exhaust fan,sealing cable end, dismantling blades of any make, any sweep, and refixing after necessary repairing such as winding of motor, replacement of capacitor & ball bearing of Exhaust fan, cleaning all dust & painting with existing colour synthetic enamel paint by spraying including filling cavities with filler,one coat including writing MES No. complete all as specified and directed by Engr-in-charge

M & L Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed by Engr-in-Charge.

S & F double door, sheet metal enclosure, powder coated for MCB DB TPN DB 8 way fitted with neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as specified and as directed by Engr-in-charge.

26. M&L for Earthing complete with galvanized steel earth plate electrode 60cm x60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level connecting to the galvanised earth lead wire 4.0 mm dia by means of bolts, nuts check nuts and washers of galvanized iron and steel earth wire protected by provision of GI mediumgrade pipe 15mm bore including provision of concrete pit made with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4Kg/Sqm) and frame of angle iron 40x 40x6 mm and handle of 6mm dia MS bar made to shape, GI light grade 20mm bore pipe for watering perforated at bottom, 1.75meter long placed on top edge of earth plate, common salt & charcoal filling with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate No -5 of SSR 2009 Part-I and connecting to Lighting protection earth test points all as specifed and directed including testing on completion.

Excavation in trenches n. exc 1.5 m in depth and not exc 1.5 m wide for laying of UG cable / pole etc and getting out including forming bottom surface to required level and gradient in soft/dense soil complete all as specified and directed by Engr-in-charge

Returning filling in, excavated soil including spreading, leveling, watering and well ramming in layers not exc 25cm thick complete all as specified and directed by Engr-in-charge

Removing excavated materials/soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5 above the starting point complete all as specified and as directed by Engr-in-Charge.

Supply & Laying & commissining of LT UG cable XLPE sheathed PVC insulated, screened PVC bedded, galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volts grade, laid in tranches, in GI pipe, including brass cable glands, clamps etc of size 4 core x 25 Sqmm complete all as specifed and as directed. Make : Polycab/KEI/Havells Note: Earthwork, sand cushioning, bricks, GI pipe, etc will be measured and pad under appropriate items.

Supply & Laying & commissining of LT UG cable XLPE sheathed PVC insulated, screened PVC bedded, galvanised steel strip of wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volts grade, laid in tranches, in GI pipe, including brass cable glands, clamps etc of size 4 core x 10 Sqmm complete all as specifed and as directed. Make : Polycab/KEI/Havells Note: Earthwork, sand cushioning, bricks, GI pipe, etc will be measured and pad under appropriate items.

Supply and Laying Double wall corrugated pipe(DWC pipe, Specification-120 mm OD/103 mm ID) for laying XLPE LT UG cable by DWC pipe throughout the LT cable length in pieces of convenient lenth .(Note : in pieces for easy rectification during fault ).

Excavation in trenches n. exc 1.5 m in depth and not exc 1.5 m wide for laying of GI tubes etc and getting out in soft/ dense soil complete all as specified.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick complete all as specified and directed by Engr-in-charge

Removing excavated soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5 above the starting point complete all as specified and as directed by Engr-in-Charge.

Supply, laying and jointing GI tubes, medium grade40mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in trenches complete all as specified and directed by Engr-in-charge.

Supply, laying and jointing GI tubes, medium grade 25mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in trenches complete all as specified and directed by Engr-in-charge.

Supply, laying and jointing GI tubes, medium grade 20mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in walls/under floors complete all as specified and directed by Engr-in-charge.

Supply and fixing Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engr-in-charge

Cutting existing steel tubing for alterations or additions done in position without taking down for 10mm to 40 dia pipe (Each cut measured)

S&F Gun metal gate valve 20mm bore with iron wheel head screwed both ends for iron pipes complete all as specified and directed .

Please Enable Macros to View BoQ information