Construction of Pilgrim House

Amount

Earth work excavation for foundation (for narrow excavation) in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

a)0.00 to 2.00 m depth

Supplying and filling in foundation and basement with filling crushed stone sand in layers of 150mm thickness well watered rammed and consolidated complying with relevant standard specifications including cost of filling sand as directed by the Departmental officers.

Refilling with excavated earth in layers of not more than 15cm thick well rammed & consolidated including watering etc..

Plain cement concrete 1:5:10 ( One of Cement, Five of crushed stone sand and Ten of hard broken stone jelly ) mix using 40mm metal hard broken stone jelly including all cost & conyeyance of all materials and all labour charges including shoring , strutting and baling out water wherever necessary remming curing etc,complete complying with standard specification as directed by the departmental officers.

Providing and laying in position, Standardised Concrete Mix M-20 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kg/mᶾ and maximum water cement ratio of 0.50, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers.

a)For foundation and besement

b) Super structure in GF

c)Super structure in FF

d)Super structure in Terrace

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as floor slab,roof slab,beam,lintel,bed blocks and landing slab, waist slab,portico slab beam etc

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing,etc.

Supply and fabrication of steel placing in portion high storey in deformed bars for RCC works as per design given including of cost of steel and binding wire etc and labour charges etc complete as directed by the departmental officers .

Brick work with cement mortar 1:5 mix using Iind class Chamber burnt bricks to a size 9"x43/8"x 23/4" including all cost and conveyance of all materials and all labour charges etc . Complete as directed by departmental officers .

a) Foundation and basement ( Cement Mortar 1:5 )

CEMENT MORTAR 1:6

a) Super structure in GF ( Cement Mortar 1:6 )

b) Super structure in FF

c) Super structure in Terrace

Brick work Partition 11.50cm thick using IInd class Chamber burnt bricks of size 9"x 43/8"x23/4" in CM 1:3, including plastering both sidewith CM 1:4 ,12mm thick including cost of conveyence of all materials to the site and all labour chargesfor laying , mixing mortar curing as directed by the departmentsl officers , etc complete .

a) Super structure in GF

b) Super structure in FF

Plastering with cement mortar 1:5 , 12mm thick including all cost and conveyence of all materials and all labour charges etc complete as directed by the depsrtmental officers complying with standard specification as directed by the departmental officers .

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing in position of matt finish Colour Vitrified Floor tiles of 600 X 600 MM x 8 MM of approved special quality of 08 mm thickness laid in cement mortar 1:3( One of cement and three of sand) 20mm thick for flooring including cost of tiles fixing in position cutting the tiles to the required size wherever necessary pointing the joints with white/ colour cements neatly curing, finishing including cost of cement mortar etc complete and as directed by the departmental officers.(Double charged tile)

Supplying and flooring with following joint free rectified glossy ceramic tiles of size 305 x 305 x 8 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supplying and fixing in position of colour glazed wall tiles for Dadooing with printed design colour glazed tiles of size 300 x 450 x 8mm thickness laid in cement mortar 1:2( One of cement and two of sand) 10mm thick for wall facing / dadoing ,skirting over the plastered surfaces including cost of tiles fixing in position cutting the tiles to the required size wherever necessary pointing the joints with white/ colour cements neatly curing, finishing including cost of cement mortar etc complete and as directed by the departmental officers. Note:(The colour make and quality shall be approved from the Competant Authority before use)

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with crushed stone sandcushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings..... such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Enginer before use on works) White glazed European Water Closet with 10 litre capacity PVC flushing tank fixed on to wall

Supplying and fixing in position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Nahani Trap of size 100 x 75mm with stainless steel gratings

Supply and fixing CP 2way Bib cock with Health Faucet

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying, laying and jointing CPVC pipes (having working Standard Dimension ratio 11) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using CPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works.

a) 20mm dia

Supplying, laying and jointing UPVC pipes of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.

20mm dia

25mm dia

32mm dia

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

a) 110mm dia

Painting the new walls surface with two coats of approved plastic emulsion over one coat of primer including cost of brushes emulsion paint and labour charges etc., all complete complying with relevant standard specification and as directed by the departmental officer.

Supplying and applying of two coats of plastic emulsion paint of approved shade and colour over one coat of primer including one coat of Acrylic wall putty with primer. Rate including all brush , roller, ladder, scrapping, washing, materials, labour charges, wastages, cleaning, necessary lead and lifts, scaffolding,stagging, working at all levels, elevations' transportation charges, loading, unloading, curing, sanding, touch-up putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the departmental officers. ( Internal surface )

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

32mm dia

25mm dia

Supplying & fixing PVC water tank i/c plumbing work etc complete and as directed by the departmental offficers.

a) 1000 Ltrs

Supplying and fixing of SS Sink of size 600 x 600 x 200 MM with 32mm dia 'B' Class G.I.waste water pipe & 32mm dia C.P. wastecoupling extra completed with standard specification

Supplying and fixing in position best quality and approved make Indian made Hindware (ALTO CAT.No:- 10091), Parry Ware or Equvalent white / colour glazed earthernware wash hand basin of size 550 x 400 x 835 mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

FRP door Sutter with FRP door frames made out of FRP Sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using MS Angle / Flats, cost of holdfasts and solid core FRP shutter Panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., of sizes specified by Engineers.

UPVC Ventilator - Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride)Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned.Radiations pin headed glass 4mm thick should be provided in the louvers.The ventilator should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved before use on work directed by the departmental officers.

Fabricating, Supplying and fixng in position of Steel Windows (Three Leaves) with the following specifications. Outer frames of windows made of 'Z' section F7D of size 33 x 25 x 3mm at 1.419 kg/ m and mullion 'J' section (F4B) of size 46 x 25 x 3mm at 2.28 kg/m and shutter section of made of F7D of 33 x 25 x 3mm at 1.419 kg/m as specified in IS 7452 / 1990. Each openable shutter should not exceed a width of 600mm to enable separate operations and easy maintenance. The panel of the shutters to be covered with 18 gauge cold rolled sheet of superior quality and welded intact with shutter frames. Horizontal stiffeners using 18 x 5mm MS Flat at 0.70 kg./m at 3 Nos. for each shutter and additional diagonal stiffners of the same MS flats at all the four corners of each shutters to the suitable length welded to the shutters, for holding the CR Sheets in position firmly. 2 numbers of sturdy hinges and one number of handle-cum-latch of special type made with 18 x 5mm MS flats are revetted to the shutters at an appropriate height in window. suitable opening is left for its easy operation. a stopper square rod for handle is provided in the mullionsection at suitable place to catch the window handle. Each window shutter having an adjustable position, a matching peg is provided in the outer frame of the window at suitable place .

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

160mm dia PVC soil / waste pipe (H150m+v50m)

110mm dia PVC soil / waste pipe (H150m+v50m)

75mm dia PVC soil / waste pipe (H150m+v50m)

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of zink chromate priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Stainless Steel (Salem Stainless Steel) Door Frame (Box Section using Stainless Steel Plate of 1.6mm thick) of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel hold fast etc., with one coat of zinc chnomate yellow primer and filling the inside hallow portion with cement concrete 1:2:4 using 20mm HBG stone jelly etc,complete complying with standard specification.

Supplying and fixing solid core particle board flush shutter of nominal thick of 35 mm with necessary T.W. internal lipping conforming to IS 2302 with both sides alround commercial ply 35mm thickand furniture fittings such as 1no .200x12mm aluminium tower bolt 2nos. 150x12mm aluminium tower bolts 1no. 250x16mm aluminium aldrops, 3 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., Including Labour wrought and put up in position Shutters for panelled doors including labour charges for fixing furniture fittings complying with standard drawings and standard specification.

Supplying and fixing in position PVC specials of ISI mark of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

PVC pipe 110mm

PVC Elbow with Door

PVC Elbow

PVC " Y" with Single Door

PVC Vent cowl

PVC Coupler/Tee with Door

PVC Bend

PVC pipe 75mm

PVC Elbow with Door

PVC Elbow

PVC " Y" with Single Door

PVC Vent cowl

PVC Coupler/Tee with Door

PVC Bend

Supplying and fixing UPVC specials of fenolex brand or equilent brand in the water supply connection pipelines as instructed by the departmental officers

32mm dia

Elbow

Coupler

Reducer Tee 32 mm x 25 mm

25mm dia

Elbow

Coupler

Reducer Elbow 25 mm x 20 mm

20mm dia

Elbow

Coupler

Supplying and fixing in position of stainless steel hand rails with Balustarder for stair case with top hand railing pipe of 50-80 mm dia with 40mm vertical post at 1000mm interval to a height of 900 mm with horizontal support fabrication pipes of 38.30 mm dia - 2 line, pipe design with 12 mm dia pipe connecting two vertical and bottom horizontal pipes and fixing 100 mm dia ring with 12 mm dia base cup for every vertical post all stain less steel pipes are 1.60 mm thick pipe, 304G to be fixed and fabrication with gas tungsten arc welding, fixing with lock fix paste and cleaning with passivation paste to remove the welding film with fine polishing including drilling the tiles or granite including conveyance, loading unloading etc all complete complying with relevant standard specification and as directed by the departmental officers.(The quality of all the materials should be got approved before use on works)

Paving the floor with pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing polymer coating (waterproof coating) for sunken portion of toilet and terrace floor with following specification on the surface shall be cleaned to remove all dust foreign metals loose materials or any of the deposits of contamination by rubbing with wire brush. Celebrity dry blend and the polymer liquid blend shall be mixed into a desired ratio as per the recommendation of the supplier. The mix shall be stored thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on both clean surface. After drying, second coat shall be applied on the first code as directed by the departmental officers etcetera. The rate inclusive of cost of materials and labels, etc complete.

Construction of inspection chamber of size 60 cm x 60 cm x 60 cm including earthwork excavation , CC1:5:10 of 10cm thick and brickwork in CM1:5 ( One Cement and Five sand ) using best quality of second class Table mould Bricks of size 9"X43/4"x23/4" with plastering with Cement mortar 1:3 ( One Cement and Three Plastering sand ) 12mm thick to inner and outer sides and wearing coat 1:3:6 ( One Cement , Three crushed stone sand and Six aggregate ) 15 cm thick and covered with precast slab 50mm thick etc., compiete complying with standard specification.

Electrical Works

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessoires and with metal box and 6A 1way modular Switch with suitable modular front place cover on wall with painting of suitable colour for open PVC light point / fan Point (for electronic regulator) (5 points per coil) (Anchor Roma/Equivalent)

Wiring with 2 x 1.5 sq.mm. PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed on wall and ceiling with PVC accessoires and with module switch box in flush with wall with 6 amps one way module switch with module front plate and making good of the concealed portion with suitable colour for concealed light / fan point (6 points per coil) (Lower end)

Supply and fixing of single box type 4feet 20w LED fitting complete with LED tube with TW round blocks on wall or ceiling with flu tube with PVC unsheathed copper leads from terminals to the fitting

Supply and fixing of 25W LED street light fitting with LED (Lower end) with 19mm dia. GI pipe (class B) with 1 no.19mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting.

Supply and fixing of WT bulk head fitting with guard suitable for 11W CFL lamp with CFL

Supply and fixing of ceiling fixture with 15w LEDbulb for night lamp

Supply and fixing 15" (375mm)sweep Heavy duty AC Exhaust fan , Complete without hole provision

Supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Lower end) with 300mm down rod on the existing fan clamp

Supply and fixing of Fan Box

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall

Supply and fixing of 3 nos.6A two module 5 pin socket , 3 nos. 6A one module switch on suitable module surface mounting Box ( GI ) with module cover plate (plastic) on wall with connections. Lower End

Supply and fixing of 1 no. 16A one module switch with module cover plate (plastic) an suitable moduled concealed box (GI) in flush with wall with connections (lower end)

Supply and fixing of 1 no. 16A two module socket with module cover plate (plastic) on suitable module consealed box (GI) in flush with wall with connections (lower end)

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug)

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 40 A DP MCB Isolator as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Lower End

Supply and fixing of 4 way Horizontal Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 40A 4P MCB Isolator as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 200A TPN, sheet gred double brake switch with HRC fuses and neutral on suitable angle iron frame work. With M.S cable entry holes and with earth connection only

Supply and fixing of 4 way vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63 A 4P MCB Isolator as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Lower End

Supply and fixing of 4 way vertical triple pole and neutral MCB sheet steel eclosure DB with double door concealed with 1 No 100A 4 pole MCB isolater as incoming and 4 Nos 63A three pole MCB as in flush with wall with earth connection only higher end

Supply and fixng of TNEB meter board suitable for 3 phase 200A service connection made up of suitable angle iron frame work of size 3 feet x 2 feet using angle iron of size 1-1/2" x 1-1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 3 feet x 2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos. 200A fuse units (500V), 1 No. neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 19/16 PVC insulated copper wire with earth connection complete

Supply and fixing of 200 A Three phase 500V 4 Pole Change over Switch on suitable angle iron frame work with MS cable entry boxes with earth connection only.

Earthing as per PWD standard with an earth electrode of 2 metre Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work

Supply and fixing of 32amps DP MCB with suitable enclosure in flush with wall with earth connections

Supply and Run of 2 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour.

Supply and Run of 1of no:8 SWG copper wire in suitable pvc rigid wire on wall / floor / ground for earth connection .

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour

Supply and run of 2 of 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with contiinuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour

Supply and Run of 4 of 10 sq.mm. (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour.

Supply and run of 4 of 25 sq.mm. PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire with portion of suitable colour

Supply and frxing of brass cable gland for 3-1/2 x 70 sq.mm. PVC armoured LTUG cable with earth connection

Supply and laying of 3½ x 70 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and clamping of 3½ x 70 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supplying & providing cable end termination of 31/2 x 70 sqmm pvc LTUG Al. armoured cable with necessary Al. cable gadeets by cramping etc., with electrical connections complete

Drilling of 140/150mm dia bore well in sedimentary or Alluival Soil strated by first taking a pilot bore of 140mm/150 dia nd then enlarged to the required dia by direct or Rotar mud circulation method using contractor power rotory ( VI z ) Tools labour for drilling and water transportations of machince from one place to another place of half to drilling site and piont ot point in various palces as directed by the engineer in charge.

Up to 60m Depth

Reaming from 140/150mm pilot bore to 300mm dia bore as directed by the TWAD size bore as directed by the TWAD Board officers upto 60m Depth ending from ground level..

Up to 60m Depth

Supply of 160 mm PVC Special Blue casing pipe of best approved quality etc complete as directed by the departmental officers. The pipe should got approved by the Executive Engineer before use on works.

Supply of 160 mm PVC Special Blue Slotted casing pipe of best approved quality etc complete as directed by the departmental officers. The pipe should got approved by the Executive Engineer before use on works.

Labour charges for inserting the casing pipes ( with and without) slots in the drilling holes incluidng jointing the pipes with PVC coupling with cement paste etc.,

Charges for developing the borewell with Air Compressor of 300 CFM capacity ( Minimum 8 hours) including transportation labour and fuel charges for compressor as directed by TWAD bd. Officers and conducting yield test by "V" Notch methods.

Supplying fixing of 2HP Submersible single phase motor with all accessries like starter,cable etc complete complying with standard specification and as directed by the departmental officers

Supplying, Fixing and connecting of 2x32 sq.mm seathed cable wire for the sub-mergible motor from pannel board to sub-mergible pump.

Supplying fixing and connecting of 3 phase panel board including labour charges

Supplying and fixing 32mm dia HDPE pipe for sub-mergible pump in Bore well (class-5 1 MPa or 10 Kg / cm2 pressure) of best approved quality including welding wherever necessary etc., complete as directed by the Executive Engineer. The pipe should be got approved by the Executive Engineer before use on works.

Sub Total

N.NATARAJAN