CWEAFJ-14/2022-23 SPECIAL REPAIR TO OFFICE ACCOMODATION OF PCDA (NC) OFFICE COMPLEX AT AF STN JAMMU

Amount

B/R Portion

Demolition of brick work or stone / boulder masonry built in cement mortar including all quoins, arches, pillars etc all as specified.

Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified and directed.

All as per the description of Serial Item No '02' here-in-before but except bricks i.e. using serviceable bricks obtained from demolition, complete all as specified and directed.

Cement concrete type B-0 1:2:4 using 12.5mm graded crushed stone aggregate in roof kerbs or mud stops, copings, kneelers, apex stones, bed plates, kerbs, rounded or chamfered on edges, complete all as specified and directed.

Taking down cement plaster on bricks or stone wall/ceiling decayed surfaces of concrete from roof projection or RCC chajjas etc. including racking out joints, hacking for key, scrubbing down with water etc., complete all as specified and directed.

Rendering 15mm thick in cement mortar 1:4 on brick work or concrete surfaces, mixed with integral water proofing compound, finished even and smooth without using extra cement, complete all as specified. Note : Integral Water Proofing Compound shall be measured and paid separately.

Supply only Liquid Water Proofing compound all as specified and as directed.

Rendering 15mm thick in cement mortar 1:6 on brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and as directed.

Rendering 10mm thick in cement mortar 1:3 in Fascia or edging of Chajjas, Ceiling and Roof projections etc., including taking out pealed off plaster / concrete and making the line in true shape and finishing the surface without using extra cement, complete all as specified and as directed.

Preparation of old RCC / Concrete surfaces of any description and in any position such as RCC Chajja, Fascias, Balconies, Projections etc. by racking out and removing old cracked / disturbed surface of concrete and applying neat cement slurry @ 3.0 Kg/Sqm and providing RCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) including necessary formwork, moulds etc. and finally finishing the work by rendering in cement mortar 1:3 and providing three coats of cement base paint / white wash to match the existing finish complete all as specified and as directed. Note : The work is to carried out at height upto 10 metres. The contractor shall make necessary arrangement for the scaffolding and saftey provisison and the cost of the same shall be deemed to be included in the rates quoted rates by the contractor and nothing extra shall be admissible on this account.

Demolition of cement concrete in ground floors and paving (un-reinforced) not exceeding 15cm. thickness, below or above ground level, complete and removing rubbish from the site, complete all as specified and directed.

75mm thick, plain cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection etc., finishing surface even and fair without using extra cement including making joints with bitumastic filling in proportion of bitumen and sand 1:3 by weight complete as specified and directed. Note : The concrete shall be laid at a stretch not exceeding 3.0m in length and joint shall be made at every turning / corners, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed.

Vitrified ceramic tiles, light shade, any pattern of size (Pattern consists combination of two or more tiles) 600mm x 600mm x 9 to 10mm thick, over and including 15mm thick screed bed in CM 1:4 as in floors etc. jointed in neat cement slurry and pointed in coloured cement to match coloured tiles, complete all as specified and directed.

Non-skid coloured glazed, joint free (matt finish), ceramic tiles of any shade and any pattern of size (Pattern consists combination of two or more tiles) 400mm x 400mm x 7mm thick, over and including 15mm thick screed bed in CM 1:4 as in floors etc. jointed in neat cement slurry and pointed in coloured cement to match coloured tiles, complete all as specified and directed.

Glazed ceramic coloured, joint free, wall tiles in any type and in any pattern (Pattern consist of combination two or more different colour tiles etc.) in vertical surfaces of size 450mm x 350mm x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick backing coat in CM 1:4, finished fair to received the tile, complete all as specified and directed.

Granite Stone, 16 to 18mm thick, (table rubbed and polished) in platform bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone over and including 15mm thick screed bed in cement mortar 1:4 finished fair to received the granite including rounding the exposed edges, complete all as specified and directed.

Taking down chowkhats with shutters (without taking off shutters from the frames not exceeding 1.50 Sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good the disturbed surface complete all as specified and as directed.

Taking down chowkhats with shutters (without taking off shutters from the frames exceeding 1.50 Sqm and not exceeding 4.00 Sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good the disturbed surface complete all as specified and as directed.

Taking down shutter of any description, exceeding 1.00 Sqm and not exceeding 2.00 Sqm each all as specified and directed.

Taking down shutter of any description, not exceeding 1.00 Sqm, and refixing the same after easing and adjusting complete all as specified and directed.

Pressed steel frame for door with one or more rebates including necessary lugs, fixing lugs hinges, lock strike plate etc. of size 105mm x 60mm and made of 1.25mm thick MS sheet, complete all as specified and directed including necessary welding complete and including medium weight 03 No's of MS butt hinges of size 75mm / 100mm / 125mm and 01 No 50mm Size of medium weight MS butt hinge, complete all as specified and directed.

Pressed steel frame for door with one or more rebates including necessary lugs, fixing lugs hinges, lock strike plate etc. of size 125mm x 60mm and made of 1.25mm thick MS sheet, complete all as specified and directed including necessary welding complete and including medium weight 03 No's of MS butt hinges of size 75mm / 100mm / 125mm and 01 No 50mm Size of medium weight MS butt hinge, complete all as specified and directed.

PCC 1:3:6 type C-0 (using 12.5mm graded crushed stone aggregate) as in back filling of pressed steel frames and in bed block for holdfast etc. similar work etc. complete all as specified and directed.

35mm thick 2nd class Hard wood factory made rail and style plain framed, panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

35mm thick, 2nd class Hard wood, factory made, glazed and skelton shutters open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkhats, complete all as specified and as directed.

Flush shutters, solid core construction, 30 mm thick, with particle board core & plywood face panels, decorative face veneer on both side with lipping / frame type on both sides, complete all as specified and as directed.

Anodised aluminium powder coated Frame (minimum thickness pf powder coating 50 microns) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

Anodised aluminium powder coated Window and Ventilator Shutters, side hung type without sash bars, aluminium sections weighting 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fitting such as stainless steel friction less hinges suitable handle (01 No) complete all as specified and as directed.

Anodised Aluminium Grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the window frame with C.P. brass/ stainless steel screw @200 mm centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved aluminium standard section around the opening, all complete as per requirment and direction complete all as specified and as directed.

Repair & refixing in same position of aluminium anodised door shutters of any description, size exceeding 1.50 Sqm but not exceeding 4.00 Sqm by taking down frame without taking off shutters from the frame, disconnecting carefully shutter member with deligated tools and as per manufacturer's instructions, removing broken aluminium mongeries, tilted / deformed aluminium beads, torn T rubber gasket and cleats in hollow blocks of rails and re-tightening in same position with larger sectional area steel screws including tightening mild steel rod with nuts in hollow blocks of members of shutters of lock side rail and hinge side rails and re-assembling shutter with old retrieved members carefully such as ACP Panel / Prelaminated Board, tinted glass 5.5 mm thick in same

situations and securing both side by supply and fixing new rubber T gasket and aluminium beads to make the door air tight including refixing of old aluminum hinge, tower bolt, mortice lock, bolts, handle, door stoppers, hydraulic door closer and re-fixing shutters in same opening after assuring complete alignment etc. Repairing floor spring where provided including making good alignments and also adjusting door chowkats and frame and refixing with new rawl plugs and 3" to 4" long standard steel flat headed screws and assuring the strength of chowkats / frames before refixing shutters etc complete all as specified and directed.

Toughened glass 12mm thick as in hinged doors, partitions automatic dooors and similar work including cutting to shape , drilling holes required including necessary fixing cleats, handles etc. complete all as specified and as directed.

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty, complete all as specified and as directed.

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty, fixed in repairs, complete all as specified and as directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with printed PVC sheet reinforced with M.S. Square tube complete all as specified and directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and as directed.

Mild steel framed works such as grills, framed guard bars, etc. barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar workand similar work conforming to Fe-410-O or Fe-310-O grade, including bending, cutting and welding as required, complete all as specified and as directed.

0.80mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required, complete all as specified and directed.

Butt hinges, medium weight, Stainless Steel, 75mm size, complete all as specified and directed.

Butt hinges, medium weight, Stainless Steel, 100mm size, complete all as specified and directed.

Butt hinges, medium weight, Stainless Steel, 125mm size, complete all as specified and directed.

Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) 250mm, and fixing clips of sheet and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Stainless Steel sliding door bolt, 250 mm, with hasp, staple (bolt type) and fixing clips of sheets, bolts and sliding bolts of extruded sections, complete all as specified and directed.

Stainless Steel barrel tower bolt complete of size 200mm long complete all as specified and directed.

Stainless Steel barrel tower bolt complete of size 100mm long complete all as specified and directed.

Stainless Steel barrel tower bolt complete of size 75mm long complete all as specified and directed.

Stainless Steel handle complete of size 125mm long complete fixed in repairs complete all as specified and directed.

5.50mm thick sheet tinted glass and glazing with oil putty, wooden beads or fixed in aluminium window shutter with EDPM rubber in squares exceeding 0.5 Sqm in each pane complete all as specified and as directed.

5.50mm thick sheet glass ordinary quality and glazing with oil putty, wooden beads or fixed in aluminium window shutter with EDPM rubber in squares not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

4mm thick figured glass, pin head type and glazing with oil putty, wooden beads or fixed in aluminium window shutter in squares not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers exceeding 1.50 Sqm area complete all as specifed and as directed.

Stainless Steel Wire Cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.

Dismantling boarding, any description, fixed in any position with screws complete all as specified and directed.

Prelaminated particle board, 18/19mm thick interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination type, fixed with screws to timber framework, all as specifed and as directed.

Brass continuous (Piano) hinges, 40 mm width of flap, complete all as specified and directed.

Continuous (Piano) hinges, 40 mm width of flap mild steel, bright finish or electrogalvanised, fixed in repairs, complete all as specified and directed.

125mm size, Brass Handles, cast type polished bright complete all as specified and directed.

Stainless Steel Hasp and Staple, 125mm safety type with mild steel hinge pin including bolt type complete all as specified and directed.

Gypsum board 8mm thick of size 595mm x 595mm as in false ceiling fixed with screws on and including Galvanized iron snap grid section of size 24mm x 38mm x 0.7mm thick ‘T’ section and 25mm x 25mm x 0.35mm thick wall cleat of angle section and 4mm dia galvanized iron wire suspended with 4mm thick grid of size 600mm x 600mm and shall be fixed to galvanized iron snap grid of above section with mild steel screws as per manufacturer’s instructions including two coats of distemper oil emulsion (combination of two shade / colour / pattern) over a coat of cement primer complete all as specified and as directed including making holes, cutting chases and making good the disturbed surfaces in cement mortar 1:3 or PCC 1:2:4 type B-1 as per the existing finish, fixed in repairs, complete all as specified and directed.

Complete removal of the existing Roof Treatment, any type viz. tarfelt or membrane surface etc. including grubbing up of tree roots and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water all loose dirt / dust complete all as specified and as directed.

PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) average thickness 25 mm thick in roof leveling concrete laid to slope for further treatment using water proofing compound as per manufacture's instructions including fair finishing to top surface complete all as specified and as directed. Note : Water Proofing Compound will be measured and paid separately.

Preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water all loose dirt/dust and applying the following Roof Treatment complete all as directed :- (a) Applying 1st course of 10mm thick screed bed with cement mortar 1:3 over concrete surface. (b) Applying 2nd course of bituminous primer conforming to IS-3384 @ 0.4 Kg/Sqm over the screed bed. (c) Applying 3rd coarse of a coat of blown type bitumen of grade 85/25 heating to a working temperature of 180° C and applied @ 1.2 Kg/Sqm.

(d) Applying 4th course of APP (Atactic Polypropylene) modified prefabricated five layer polymeric membrane 3mm thick weight not less than 3.6 Kg/Sqm with 160 Grams/Sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 100 mm end overlap. (e) Applying 5th course of a coat of bonding material with blown type bitumen of grade 85/25 heating to a working temperature of 180° C and applied @ 1.2 Kg/Sqm and blended with fine sand in dry condition @ 0.50Kg/Sqm dusted over the bitumen coat. (f) Applying a 6th course of Solar Reflective Bituminous Aluminium Paint @ 100 grams/Sqm all as specified and as directed.

The membrane shall be laid using butane torch. The membrane shall be first laid upto the parapet wall junction and then shall be overlapped with another membrane (flashing) with an overlap covering upto a distance of 300mm. In case the parapet height is less than 500mm, the membrane shall be terminated at the top of parapet. All rain water pipe openings shall be suitably sealed with APP membrane including disconnection and refixing in same position the existing Water Storage Tanks and all GI Pipes and fittings complete all as specified and directed. Notes : 1. Contractor shall be write "Name of Contractor and Date of Laying of Membrane" with paint on the wall after laying of membrane in all respect. 2. The rate includes for filling of cracks in existing roof with cement putty using suitable bonding agent (Shalocrate-42) before laying cement plaster all as directed.

Rendering 15mm thick in cement mortar 1:3 on concrete surfaces of sunken portion, mixed with integral water proofing compound, finished even and smooth without using extra cement, complete all as specified. Note : Integral Water Proofing Compound shall be measured and paid separately.

Disconnecting existing water tank, capacity exceeding 250 Litres but not exceeding 500 Litres, setting aside (or lovering if required) for cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipe and hoisting if required, reconnecting and re-fixing in position, complete all as specified and directed.

Rotational moulded polyethylene Water Storage Tanks of capacity 1000 litres, (cylindrical vertical with threaded top), three layered, white colour, hoisted and fixed in position including supply and fixing necessary GI fittings, inlet/outlet washout, overflow pieces long nipples, check nuts & washer, brass valve 20mm high pressure with polythene float and fly nut etc. complete, fixed in repairs, all as specified and directed.

Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed to 20mm bore dia of pipe (Minimum weight 142gms) in repairs complete all as specified and directed.

Pillar taps, cast copper alloy, fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe of 15mm bore, complete all as specified and as directed. Make : Jaquar Cat Part No CON-011KN / CERA Cat Part No F3001101 / equivalent in KOHLER / ROCA

Bib tap with wall flange cast copper alloy chromium plated, fancy type long shank type, with capstan Head handle, screwed down, screwed for 15mm bore iron pipe or for brass ferrule, fixed in repairs, complete all as specified and directed. Make : Jaquar Cat Part No CON-037KN / CERA Cat Part No F3001151 / equivalent in KOHLER / ROCA

Stop cock / Angle valve with CP cast copper alloy, with capstan head handle and adjustable wall flange, screwed down, high pressure screwed both ends for 15mm bore iron pipe or for unions, fixed in repairs, complete all as specified and directed.

Stop cock / Angle valve with adjustable wall flange CP cast copper alloy, fancy type, with capstan head handle and adjustable wall flange, screwed down, high pressure screwed both ends for 15mm bore iron pipe or for unions, fixed in repairs, complete all as specified and directed. Make : Jaquar Cat Part No CON-053KN / CERA Cat Part No F3001202 / equivalent in KOHLER / ROCA

Vitreous china water closet Orissa pattern, size 580mm x 440mm , with ‘P’ or ‘S’ trap, front or back inlet and integral foot rest complete including lime concrete bedding and connection to drain or outgoing pipe and to flushing pipe, and anti siphon pipe, fixed in repairs complete all as specified and directed.

Vitreous china wash down water closet pan (pedestal pattern) white, including ‘P’ or ‘S’ trap, white seat cover with flat bottom and mild steel CP hinging device, CP brass jet nozzle with 1500 mm long PVC pipe, fixed in repairs, complete all as specified and directed.

10 litres capacity PVC low level flushing cistern of approved make complete with PVC flush pipe and connection to water closet, fixed in repair, complete all as specified and directed.

PVC Seat Cover, white colour, with solid flat bottom and mild steel CP hinging device, fixed in repairs, complete all as specified and as directed.

Flush pipe of polyethylene of low or high density or PVC, 32mm dia, for low level cistern, fixed in repairs, complete all as specified and as directed.

Health Faucet (ABS body) mild steel chromium plated sutaible for 15mm dia pipe with 1.25 mere long flexible tube and ABS wall hook including making connections and fixing in position complete, fixed in repairs, all as specified and as directed. Make : Jaquar Cat Part No ALD-587 / CERA Cat Part No F8030103 / equivalent in KOHLER / ROCA

Vitreous china wash hand basin white flat back size 550mm x 400mm, white flat back including cast iron bracket, cutting for and pinning the ends of brackets or erecting on stand including 32mm bore brass chromium plated waste coupling with long screwed shank and fly nuts, PVC flexible waste pipe of bore 32mm and adequate length, 15mm bore PVC connection pipe 450mm long with brass nuts on both side, fixed in repairs, complete all as specified and as directed.

Vitreous China urinal bowl half stall type, white, with grating and union for discharge pipe (excluding flushing cistern and flush pipe) complete including providing and fixing plus, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing with brackets, flush pipe, grating and union for discharge pipe and and waste pipe, complete all as specified and directed.

PVC connection 45cm long fitted with two Nos of brass check nuts and washers complete, fixed to 15mm bore iron pipes, complete all as specified and directed.

PVC connection 60cm long fitted with two Nos of brass check nuts and washers complete, fixed to 15mm bore iron pipes, complete all as specified and directed.

Chromium Plated Grating 125mm dia complete all as specified and directed.

Chromium Plated Grating 125mm dia with waste hole complete all as specified and directed.

PVC (SWR) pipes, pressure rating 4Kg/Sqcm, single or double socketed, 110mm bore in any length with rubber ring joints, laid in walls including making joints air tight using solvent cement and adhesive, fixed in repairs, complete all as specified and directed.

PVC (SWR) pipes, pressure rating 4Kg/Sqcm, single or double socketed, 75mm bore in any length with rubber ring joints, laid in walls including making joints air tight using solvent cement and adhesive complete all as specified and directed.

PVC (SWR) bend 110mm bore with access door including making joints air tight using solvent cement and adhesive complete all as specified and directed.

PVC (SWR) bend 75mm bore with access door including making joints air tight using solvent cement and adhesive complete all as specified and directed.

Stack clamp made of 50 x 5mm flat iron and 16mm dia round iron stays including bolt and nuts and securing ends of stay to water pipes suitable for 100 / 110mm dia pipe including taking down unserviceable clamp all as specified and directed.

Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors / walls, 100mm dia, fixed in repairs, all as specified and as directed.

Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or in floors / walls, 75mm dia, fixed in repairs, all as specified and as directed.

Cast iron bend (any radius) diminishing pieces or tapers (larger bore measured) 100mm dia, fixed in repairs, all as specified and as directed.

Cast iron bend (any radius) diminishing pieces or tapers (larger bore measured) 75mm dia, fixed in repairs, all as specified and as directed.

Cast iron Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches 100mm dia, fixed in repairs, all as specified and as directed.

Cast iron Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches 75mm dia, fixed in repairs, all as specified and as directed.

Cast iron Sockets (double) collars 100mm dia, fixed in repairs, all as specified and as directed.

Cast iron Sockets (double) collars 75mm dia, fixed in repairs, all as specified and as directed.

Cast iron Cowls 50mm dia, fixed in repairs, all as specified and as directed.

Preparation new plastered surfaces of walls upto Four Storey Height and applying 1mm thick cement based putty after finishing walls with acrylic smooth exterior paint of required shade two coats applied @ 1.67 Litres/10 Sqm over and including priming coat of exterior primer applied @ 2.20 Litres/10 Sqm complete all as specified and as directed.

Complete removal of existing treatment on walls upto Four Storey Height and applying 1mm thick cement based putty after finishing walls with acrylic smooth exterior paint of required shade two coats applied @ 1.67 Litres/10 Sqm over and including priming coat of exterior primer applied @ 2.20 Litres/10 Sqm complete all as specified and as directed.

Preparation new plastered surfaces of wall and applying two coats of oil emulsion distemper over a coat of alkali resistant primer coat over and including a coat of wall care putty (Birla/JK) of average thickness 2 to 3mm complete all as specified and as directed.

Preparation old plastered surfaces of wall and applying one coat of oil emulsion distemper complete all as specified and as directed.

Complete removal of existing treatment on walls and applying two coats of oil emulsion distemper over a coat of alkali resistant primer coat over and including a coat of wall care putty (Birla/JK) of average thickness 2 to 3mm complete all as specified and as directed.

Preparation of new or previously untreated steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint, over a coat of red oxide primer, complete all as specified and as directed.

E/M Portion

Taking out carefully copper / aluminium point wiring, (Light, fan, socket or power) complete with all fitting, fixtures such as switch socket out let, ceiling rose, holder, regulator, DB's etc. including making good the disturbed surface of wall/floors, complete all as specified and as directed.

Point wiring with multi stranded copper conductor of size 1.5Sqmm PVC insulated unsheathed FRLS cable in and including concealed PVC conduit 20mm dia or more as per the site requirement including its fittings and fixtures such as ties, bends, elbows and junction boxes etc. including 1.50 Sqmm copper earth wire (green colour) FRLS Cable as earth continuity conductor connected to main earthing and common earth terminal for one light point or fan point or bell point controlled by one No, one way switch using cable of different insulation colour for colour coding including mild steel sunken box and inner and outer plate for mounting of Modular Switches including cutting chases and making good to disturbed surfaces of wall / floor, complete all as specified and as directed.

All as per the description of Serial Item No 104 here-in-before but for one 3 pin socket outlet 05/06 Amp independent, complete all as specified and as directed.

All as per the description of Serial Item No 104 here-in-before but for one 5 pin socket outlet 05/06 Amp on same board, complete all as specified and as directed.

All as per the description of Serial Item No 104 here-in-before but for one 3 pin socket outlet 15/16 Amp independent board using cable of size 2.5 Sqmm including 2.5 Sqmm copper earth wire (green colour) all as specified and directed.

Modular Switch 1 way 06 Amps, 1 module complete all as specified and as directed.

Modular Socket, 06 Amps, 2/3 pin combined 2 module, complete all as specified and as directed.

Modular Switch 1 way 16Amps, 1 module, complete all as specified and as directed.

Modular Socket 06 / 16Amps, 2/3 pin combined 2 module, complete all as specified and as directed.

Ceiling rose surface bakelite three terminals 240 volts complete all as specified and as directed.

Electronic fan regulator step type modular, 120W - 2 module suitable for 1200mm / 1400mm sweep AC ceiling fan, complete all as specified and as directed.

Recess mounting ultra slim LED flat panel 2' x 2' 36 Watts made of extruded aluminium frame with high LEDs and glare free opal diffuser IP-20 complete all as specified and as directed.

Sheet metal enclosure factory made double door for DB 240 volts with 200 Amps rated bus bar SPN 12 Way including taking down and making good disturbed surfaces of walls, complete all as specified and as directed.

Sheet metal enclosure factory made double door for DB 240 volts with 200 Amps rated bus bar SPN 08 Way including taking down and making good disturbed surfaces of walls, complete all as specified and as directed.

MCB SP 6 to 32 Amp 10 KA, 'C' curve, complete all as specified and as directed.

MCB SPN 6 to 32 Amp 10 KA, 'C' curve, complete all as specified and as directed.

MCB SPN 40 to 63 Amp 10 KA, 'C' curve, complete all as specified and as directed.

Sub main wiring with two single core PVC insulated multistrandred un-sheathed FRLS cable of size 6.0 Sqmm with stranded copper conductor, drawing into concealed PVC conduit / surface batten (including conduit and accessories) with continuous PVC insulated multistrandred unsheathed FRLS cable earth wire of 6.0 Sqmm dia including taking out unserviceable sub main wiring, complete all as specified and directed. Note : Three runs of 6.0 Sqmm wire and one run of PVC conduit shall be considered as one unit length.

Sub main wiring with two single core PVC insulated multistrandred un-sheathed FRLS cable of size 4.0 Sqmm with stranded copper conductor, drawing into concealed PVC conduit / surface batten (including conduit and accessories) with continuous PVC insulated multistrandred unsheathed FRLS cable earth wire of 4.0 Sqmm dia including taking out unserviceable sub main wiring, complete all as specified and directed. Note : Three runs of 4.0 Sqmm wire and one run of PVC conduit shall be considered as one unit length.

Earthing complete with galvanized mild steel earth plate electrode size 600mm x 600mm x 6mm thick buried directly in ground (preferably in vertical position) earth pit not less than 2.25 meter below normal ground level with top edge of the earth plate not less 3 meter (BGL) connected to galvanized iron earth lead wire 4mm dia by means of bolts, nuts, check nut and washer of galvanized iron including PCC pit in RCC 1:2:4 type B-1, precast RCC cover with suitable handle, excavation and earth work in any type of soil, 20mm bore “medium grade” galvanized iron water tubing fixed with cast iron funnel and wire mesh and 15mm bore “light grade” galvanized iron protection pipe for earth lead wire upto 5m length, charcoal, common salt, complete all as shown in EP No 3 of SSR 2009 Part-I, connected to test point complete, all as specified and testing on completion.

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicatedsituation for loop earthing etc. as required 4mm dia galvanised iron or steel wire all as directed

Rakesh Kumar Malia

GENESIS INDIA

JK BUILDERS AND DEVELOPERS

bamral builder

ANIKET TRADERS

M/S Shesh Paul Gupta

Bidder Name

Rakesh Kumar Malia

M/S Shesh Paul Gupta

ANIKET TRADERS

GENESIS INDIA

JK BUILDERS AND DEVELOPERS

bamral builder

M/S MOHAN LAL SHARMA