Renovation of Gadkari Post for CISF and Miscellaneous Civil Works at Western Sector and various places inside BARC, Trombay

Amount

Lead charges for Lead exceeding 1 KM but not exceeding 2 KM, by mechanical transport including loading, unloading, stacking / levelling etc.

Soil Note: The rate is applicable for NET Quantities arrived at after making deduction for voids @ 20% in respect of soil from corresponding STACK / TRUCK Measurement.

Providing and laying in position cement concrete of 1:3:6 (1 cement, 3 crushed sand, 6 graded stone aggregate of maximum size 20 mm) including consolidation, finishing, curing etc. complete as per specificationsand drawings but excluding the cost of Form work shuttering, centering Complete at all levels

Providing and laying in position cement concrete of 1:2:4 (1 cement, 2 crushed sand, 4 graded stone aggregate of nominal size 20 mm) including consolidation, finishing, curing etc. complete as per specification and drawings but excluding the cost of Formwork shuttering, centering and steel reinforcement at all Levels

Providing and laying in position cement concrete of 1:1.5:3 at all levels (1 cement, 1.5 crushed sand, 3 graded stone aggregate of nominal size 20 mm) including consolidation, finishing, curing etc.. complete as per specifications and drawings but excluding the cost of shuttering, centering and steel reinforcement.

Providing and laying in position cement concrete of 1:1:2 at all levels (1 cement, 1 crushed sand, 2 graded stone aggregate of nominal size 20 mm) including consolidation, finishing, curing etc. complete all as per specifications but excluding the cost of Formwork shuttering, centering and steel reinforcement complete as per specifications and drawings at all levels

Providng and fixing at and near ground level precast cement concrete 1:2:4 in kerbs, edgings etc. as per approved patterns and setting in position with C.M 1:3 (using crushed sand) including consolidation, curing, cost of required centering, shuttering, finishing smooth with 6 mm thick cement plaster 1:3 (using crushed sand) on exposed surfaces complete as per specifications and as directed by the Engineer-in-charge

Providing and laying in position Reinforced Cement Concrete (RCC) of grade M-30 using 20mm maximum size aggregates and crushed sand of approved quality including admixtures of approved brand and quality (plasticiser or super plasticiser) if required, including weigh batching, mechanical mixing, transporting, placing, vibrating, consolidation, finishing, curing etc. complete but excluding the cost of centering, shuttering and reinforcement complete as per specifications up to Plinth Level.

Extra for RCC Using Ready Mix Concrete from outside project area including transporting and pumping from approved batching plants .

Providing Reinforcement Steel for reinforced cement concrete at all levels including supplying, preparation of bar bending schedules, cutting, bending, transporting, fixing, tieing in position with PVC coated with 1.6 mm dia soft drawn annealed G.I binding wire, all labour charges, cost of cover blocks in specified grade of concrete etc. etc. complete including cost of binding wire, complete as per specifications and drawings. - Steel supplied by the contractor. Using TMT bars of specified grades all dia bars. TMT bars of approved manufacturers to be supplied by the contractor - confirming to IS:1786. Note: Cover blocks shall be of same grade of concrete

Providing Structural steel work using angles, channels, joists and other sections, welded and / or bolted in built up sections for trusses, structural steel floors, frame works, monorails and other structures including supplying, cutting, welding, fabricating, hoisting, fixing in position, applying a priming coat of approved steel primer etc. complete all as per specifications, drawings and as directed by the Engineer-in-charge. Up to and including 300 mm Joists, 350 mm channels, and below sections using materials produced by approved make and manufacturers. All test reports to be provided along with the supply of the materials confirming to IS:2062. Note : (1) Welding weights, connections, bolts and nuts shall not be measured for payment, but the cost of which shall be deemed to have been included in the rate. Rate is also inclusive of all consumables like welding electrodes and tools and tackles etc. (2) All holes will be made by drilling only. Gas cutting of holes will not be permitted. (3) Electrodes manufactured by approved manufacturer shall be used. (4) Edges of plates shall be grinded to uniform smooth finish. (5) The contractor shall supply documentary evidence of purchase of steel, Test certificate from approved manufacturers and also third party testing from approved laboratories with out any extra cost.

Providing and fixing at all levels MS bolts including nuts and washers of approved size, quality and make as per requirements and as per specifications, drawings complete all as directed at site by the Engineer in charge

Providing , centering ,shuttering Form work using PVC film faced plywood to get a neat form finish surface for all types of structures including necessary strutting, proping, staging, supports etc and deshuttering the same after the specified time all as per drawings, specifications and as directed by the Engineer-in-charge at all levels

For Sub Structure

For Super Structure

Providing and constructing Brickwork in cement mortar 1:6 using crushed sand with Flyash / Flyash Lime bricks with minimum 70 kg / Sq. cm strength of approved make and size in Sub structure including, scaffolding, raking out joints, curing, cleaning complete all as per specifications and drawings.

Providing and constructing Brickwork in cement mortar 1:4 using crushed sand with Flyash/ Flyash Lime bricks with minimum 70 kg/ sq.cm strength of approved make and size in super structure up to and including Floor II Level including, scaffolding, raking out joints, curing, cleaning complete all as per specifications and drawings.

Providing 20 mm thick plastering using Ready mix external plastering compound of approved make for external faces of brickwork / concrete surfaces including preparation of the surface, curing, cleaning scaffolding up to 10 metres height complete.all as per specifications including forming drip moulds wherever necessary and as directed by the Engineer-in-charge

Providing and laying (IPS Flooring) cement concrete flooring 1:2:4, using crushed sand 50 mm thick finished smooth to the required level, finishing with a floating coat of neat cement including cement slurry, curing, cleaning the surface neatly at the time of handing over the area complete as per specifications and drawings as directed by the Engineer in charge

Providing and laying chequered / patterned tiles 300 X 300 mm X 30 mm thick of approved make including levelling, curing, finisihing and cleaning etc. complete to obtain required finish complete on 20 mm thick bed of cement mortar 1:4 (using crushed sand) as per specifications and drawings complete as directed by the Engineer-in-charge

Providing and Fixing Homogeneous 2.00 mm thick PVC sheet / tile in flooring and skirting of approved make in approved pattern on a smooth and damp proof base using rubber based adhesive of approved quality and manufacturer including, levelling small undulations with plasterof paris if required , rolling with light wooden roller weighing about 5 kg all complete as directed by Engineer-in-charge in approved colour and shade

Providing, supplying and laying pre polished granite slab flooring / dado / Wall cladding with 15-17 mm thick granite slabs over 20 mm thick base cement mortar 1:4 (using crushed sand) laid and placed with grey cement slurry including filling the joints with matching white cement based tile grout complete all as per specifications and drawings.

Using approved black shade

Extra for providing edge moulding to 15-17 mm thick marble stone / Granite Slab counters, Vanitis etc. including machine polishing to edge to give high gloss finish et. Complete as per design approved by Engineer-in-charge.

Granite work

Providing and fixing anodized aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically whereever required including cleat angle, aluminium snap beading for glazing / panelling, C.P brass / stainless screws all complete as per drawings and and directions of Engineer-in-charge including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required filling the gaps using silicon grout sealent etc. (fittings glazing and panelling shall be paid for separately)

Anodized Aluminium sections (Minimum anodizing thickness of 15 micron)

Providing and fixing glazing in aluminium doors, window, ventilator shutters and partitions etc with PVC / Neoprene gasket etc. complete as per the architectural drawings and directions of the Engineer-in-charge (Cost of snap beading shall be paid in basic item)

With clear float glass panes of 6.00 mm thickness

Providing and fixing double action hydraulic floor spring of approved brand and manufacturer (conforming to relevant Indian Standard) for doors including cost of cutting floors as required, embedding in floors and cover plates with M.S pivot and single piece of M.S sheet outer box with slide plate etc. complete as per directions of Engineer-in-charge with brass cover plate

Providing and fixing 4 Lever Mortice Lock of approved make suitable for aluminium sections

Providing and fixing approved quality and shape star locks cum handle of approved make for sliding shutters

Providing and fixing approved quality stain less steel body roller wheels of approved make for sliding shutters

Providing and fixing magnetic catcher triple strip vertical type 40 mm of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete .

Filling the gap between aluminium frame & adjacent RCC / Brick work / Stone work/ with baker rod if required by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete Up to 5 mm to 25 mm depth and 5 mm to 25 mm width

Providing and fixing stainless steel (SS 304 Grade) adjustable friction windows stays of approved quality with necessary stainless steel screws to the side hung windows as per specifications and as directed by the Engineer-in-charge

Designing, providing and fixing of 4 mm thick approved make and shade Aluminium Composite Metal Panel of approved make cladding at different locations including soffits of over-hangs but excluding aluminium frame work with grids filled in with weather silicon sealant as per the drawings. The ACM panel composition shall be of 0.5 mm thick PVDF coated aluminium sheet + 3 mm thick low density polyethelene virgin resin core + 0.5 mm thick polyester (PVDF) coated Aluminium sheet all complete as per approved shop drawings and specification (Aluminium frame work will be paid under reelevant item) Note : ACMP shall be measured to the actual visible area of the ACP sheet including silicon joints as fixed on site.

Providing and fixing locks for aluminium sliding window shutters of Over all size of 204mm x 23 mm all as per specifications complete as directed by the Engineer-in-charge Note : Tentative / suggested make for guidance of bidder(s) : M/s GEETAVIN as per cat. No. SS -004

Providing and Painting with Epoxy PU paint On STEEL surfaces using 2 coats of (120 Micron dry film thickness) Epoxy PU high build coating as finishing coat over a priming coat of High Build epoxy primer of 50 micron thickness over steel surfaces at all locations prepared and applied as per manufacturer' specifications including preparation of surface by cleaning with wire brush and rubbing, scraping , applying sand paper, making free of Rust, dust, dirt etc. filling the holes, joint, cracks if any using epoxy putty complete. all as per manufacturers technical data and as directed at site to achieve minimum overall dry Film thickness of 170 micron (50 Micron primer Coat + 120 micron finishing Coat).

Providing & fixing and welding of new Crimpnet Gate Jali of 50x50 mm made of 4 mm dia GI wire of dia 4mm at existing Gate place including strengthening with 2mm dia wire or nuts bolts washers including removing of an old rusted Crimpnet Jali , cleaning the area as directed by the Engineer incharge.

Providing , designing and fixing of 3.00 mt Height fencing of Galvanized and Thermoplastic Powder coated welded mesh system with SS Concertina Coil and SS Barbed wire ( blades 316 and wire SS 304 ) , including PVC H shaped post with 4 mm dia. 358 weld mesh, panel height 2.456 m and width 2.488m with 4 V Bends etc. the fencing produced by electrical resistance welding of galvanized wires and subsequently thermoplastic powder coated as per follows.: Weld mesh Panels for the fence will meet the standards of EN 10223-7 with the following key specifications apart from the other points mentioned in the governing detailed specification: (Note: There is no existing Indian standards for Weld mesh panels for fencing Applications) Weld Shear strength: Minimum 50 % of the breaking strength of the smallest wire (In this case the vertical wire) Mesh Wire: Galvanized MS wire Specification for wire Diameter: IS 280 -2006 Tensile Strength of wire: Minimum 500 N/sq.mm Galvanizing of wire: 40 – 50 GSM as per IS 4826 (Measurement as per IS 6745) Uniformity of Coating: As per IS 2633 Adhesion test for coating: As per IS 6745 / IS 2629. Powder Coating on panels: The galvanized panels are subsequently Thermoplastic Powder Coated after welding with the thickness of minimum 250 Microns. Coating Standard: EN 10245-1/ IS 13871. Powder coating should withstand 1440 Hours of salt spray test Posts are `H' shaped post, MS material are then hot-dip galvanized to minimum 360GSM and then Thermo-plastic powder coated. Post will have with pre-welded base plate of minimum 400MPA strength using 8mm fillet weld, Base plate will have suitable holes to use SS316 M20*300mm Anchor bolts which will be installed at site with Glue for better strength. Powder Coating on post: The hot galvanized posts are subsequently Thermoplastic Powder Coated after welding with the thickness of minimum 250 Microns. Coating Standard: EN 10245-1/ IS 13871 Powder coating should withstand 1440 Hours of salt spray test , fencing system will have 600 mm dia. SS Concertina Coil (blade SS 316 and wire SS 304 ) having Tensile Strength of wire: 1400-1500 N/sq.mm, Blade Profile: FBBT, Blade Length: 66 mm, Center to Center Distance Between blades: 50mm Number of loops / coil: 56 Nos,. and 12 Swg SS304 Barbed wire. Total height of fencing to be 2.456 mtr (excluding concertina coil) and width 2.5mtr (posts c/c) as per the detailed drawing and specifications which shall meet the BARC technical specification as directed by the Engineer-in-charge at all levels. (Design, preparation of Shop drawings by the contractor as per the site conditions and the same shall be approved by BARC/Engineer in charge before procurement/execution of work). Note : Test Certificate(s) for all material, coating . painting etc. to be provided by the bidder before and after execution of the work and the type test certificate should be from central electrochemical research institute.

Extra for each additional posts with accessories etc.as directed by the Engineer-in-charge at all levels for 3 m high fencing .

Providing and fixing precoated Galvalume Roofing profile sheets of approved size, shape and pitch up to and including single length of 12.00 met. The sheet shall be fixed using self drilling / self tapping screws of size (5.5 X 55 mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers filled with white lead complete upto any pitch in horizontal / vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required as directed by the Engineer-in-charge Galvalume sheet roofing 0.50 mm Thickness in Single sheet

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion. 110 mm Dia Coupler

Dismantling plain cement concrete manually / by mechanical means carefully without damaging adjacent structures including disposal of debris within 200 m lead as per direction of Engineer-in-charge

Demolishing Stone rubble masonry (In cement mortar) manually / by mechanical means carefully without damaging adjacent structures including stacking of serviceable materials and disposal of unserviceable materials within 100 m lead as per direction of Engineer-in-charge

Dismantling doors, windows and clear storey openings (steel / wood) shutter including chowkhats, architraves, holdfasts etc. complete and stacking within 100 m lead (full windows) Of area 3.00 Sq.M and below

Taking out doors, windlows and clear storey openings (steel / wood) shutter including stacking within 100 m lead (only shutters) Of area 3.00 Sq.M and below

Dismantling steel work in single sections including dismantling and stacking within 100 m lead In R.S Joists, Angles etc.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 100 m lead For thickness of tiles above 10 mm and up to 25 mm

Dismantling old ceiling plaster carefully and cleaning the surface for plaster including scaffolding disposal of rubbish to the dumping ground within 200 m lead etc. complete as directed by the Engineer-in-charge

Providing and grouting the joints of rubble stone pitching with cement mortar 1:3 and pointing the surfaces as directed complete as directed by the Engineer-in-charge

Dismantling barbed wire / flexible wire rope in fencing including making rolls and stacking within 100 m lead

Providing 20 mm thick plastering using Ready mix external plastering compound of approved make for external faces of brickwork / concrete surfaces including preparation of the surface, curing, cleaning scaffolding up to 10 metres height complete.all as per specifications including forming drip moulds wherever necessary and as directed by the Engineer-in-charge

Providing Raised and cut pointing on stone with cement mortar 1:3 using river sand as per specifications and as directed at site by the Engineer-in-charge

Marble stone flooring with 15-17 mm thick Using Udaipur Green marble slabs over 20 mm thick base of cement mortar 1:4 (using crushed sand) laid and placed with grey cement slurry including filling the joints with matching white cement slurry rubbing and polishing complete all as per specifications, drawings and as directed by the Engineer-in-charge

Providing and laying minimum 25 mm thick uniform shade Kotah stone flooring over 20 mm thick (Avearge) base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing in minimum three levels to obtain mirror polish complete with base cement mortar 1:4 (using crushed sand) all as per specifications, patterns and drawings complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS 15622 of approved make. shade and colour of size ranging from 300 - 600 mm long and 300 mm - 600 mm wide and thickness not less than 6 mm as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (using crushed sand), setting the tiles in cement slurry and pointing the joints with matching colour Tile grout of approved make of matching shade including using PVC tile trim in the exposed corners, complete as per drawings, patterns and specifications complete as directed by the Engineer-in-charge.

Providing and fixing 1st quality ceramic glazed floor tiles of minimum 300 - 600 mm long and 300 - 600 mm wide and thickness not less than 6 mm conforming to IS 15622 of approved make in all colours and shades as approved by Engineer-in-charge over a bed of 20 mm thick bed of cement mortar 1:4 (using crushed sand) and jointing with grey cement slurry including pointing with white cement based Tile grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Enginner-in-charge

Providing, applying and finishing walls with TWO Coats of water proof cement paint of approved make of required shade over new work including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

Providing and applying wall painting two coats on new work with premium plastic emulsion paint of approved brand to give an even shade, including a coat of approved cement primer, including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

Providing and Painting two coats of synthetic enamel paint on Steel Surfaces of approved brand and manufacture to give an even shade without primer coat.including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

Providing and fixing decorative high pressure 1.0 mm thick laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS:2046 Type S including cost of adhesive, labour etc. complete as directed

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams

Removing white or colour wash, distemper, external paint/ any paint by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete all as directed at site including scaffolding, cleaning of the areas.

Providing, Painting on old work (one coat) with oil bound washable distemper/ emamel paint of approved brand of exterior/interioer and manufacturer to give an even shade including preparation of the surfaces, scaffolding complete as per specifications and as directed by the Engineer-in-charge

Providing and fixing aluminium handles 175 mm long Inner grip 125 mm with 12 mm dia rod plate type BOW handles ISI marked of approved make, anodised transparent or dyed to req. colour or shade with necessary screws etc. complete.

Providing and fixing aluminium hanging heavy quality floor door stopper ISI marked with twin rubber stoppers, anodised transparent or dyed to required. colour or shade with necessary screws etc. complete.

Providing and fixing aluminium aldrops of size 250 X 16 mm ISI marked anodised transparent or dyed to requried colour or shade with necessary screws, bolting from rear side complete as per specifications and as directed by the Engineer-in-charge

Providing and fixing anodized aluminium tower bolts of size 200 X 12 mm ISI marked of approved make transparent or dyed to requried colour or shade with necessary screws etc.

Providing and fixing anodised aluminium baby latch of size 75 X 12 mm ISI marked of approved make transparent or dyed to requried colour or shade with necessary screws etc.

Providing and fixing viterious China wash basin of approved make and colour with C.I. brackets, 15 m C.P. brass pillar tap of approved make,15 mm x 600mm long PVC Inlet connection, 32 mm heavy quality C.P. brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls and testing complete all as per specifications and as directed by the Engineer-in-charge White vitreous China wash basin size 630 x 450 mm and equivalent sizes with single 15 mm C.P. brass pillar tap

Providing and fixing 6 mm thick mirrors of size 600 x 450 mm of approved make with bevelled edges complete with 6 mm thick asbestos sheet back ground fixed to walls with C.P. brass screws and concealed washers complete. all as per specifications and as directed by the Engineer-in-charge .

Providing and fixing C.P brass towel rail of approved make 600 mm long complete fixed to walls with 30 mm CP brass screws with concealed fitting arrangement all as directed by the Engineer-in-charge.

Providing and fixing C.P brass bib cock of heavy quality of specified / approved make as per specifications and as directed by the Engineer-in-charge 15 mm dia bib cock of approved type and make .

Providing & fixing in position heavy pattern screw down gun metal gate valve with handles and wheels of approved make including testing for 10 Kg/ cm2 pressure with clean and potable water with a minimum testing duration of two hours etc.as per specification and as directed by the Engineer-in-charge 25 mm n.b.

Providing, laying , jointing, fixing and testing heavy quality ( (ISI Marked C-Class) Galvanised Iron pipes and ISI marked fittings like, tees, elbows, bends, unions, nipples,reducers etc. as required for the work, including testing the pipes and fittings for 10.00 Kg / Sq.Cm hydralic pressure with a minimum period of two hours duration with clean water, including cutting , threading, jointing with hemp yarn, white lead, jointing teflon tape, chasing walls and making good by filling with concrete 1:3:6, complete all as per specifications and drawings, including two coats of anti corrosive bitumastic paint, all as directed by the Engineer-in-charge. Pipes with ISI marked 'C' -Class heavy quality pipes of approved make.

15 mm dia G.I pipe

20 mm dia G.I pipe

25 mm dia G.I pipe

Providing and fixing Stainless steel concertina barbed tape coil of 600 mm dia. made from stainless steel ribbon tape of 0.5 mm thickness, 19 mm width stretching the coil to 9 m approximate, fixing the coil with clips between "Y" armed and MS angle posts 2.44 m high from ground level, including supplying and fixing SS galvanized clips etc. complete as per manufacturer's specification and including painting by dipping method the concrtina tape coil with two coats of synthetic enamel paint of approved shade and make over a coat of approved primer at fabrication shop, before bringing the material to the site and fixing in position etc. complete as directed by the Engineer-in-charge.

Supplying and fixing in position 2 ply, 12 gauge, 4 spikes at every 100 mm c/c, Stainless steel barbed wire to M.S. angles/RCC posts including supplying and fixing with necessary" J" hooks, bolts, nuts, washers, staples etc. of make stainless steel as required etc. complete as directed by the Engineer-in-charge.( the mode of measurements is on KG basis of barbed wire only, quote accordingly )

Lead charges for Lead exceeding 1 KM but not exceeding 2 KM, by mechanical transport including loading, unloading, stacking / levelling etc.

Soil Note: The rate is applicable for NET Quantities arrived at after making deduction for voids @ 20% in respect of soil from corresponding STACK / TRUCK Measurement.

Providing and laying in position cement concrete of 1:3:6 (1 cement, 3 crushed sand, 6 graded stone aggregate of maximum size 20 mm) including consolidation, finishing, curing etc. complete as per specifications and drawings but excluding the cost of Form work shuttering, centering Complete at all levels

Providing and laying in position cement concrete of 1:2:4 (1 cement, 2 crushed sand, 4 graded stone aggregate of nominal size 20 mm) including consolidation, finishing, curing etc. complete as per specification and drawings but excluding the cost of Form work shuttering, centering Complete at all levels

Providing and laying in position cement concrete of 1:1.5:3 at all levels (1 cement, 1.5 crushed sand, 3 graded stone aggregate of nominal size 20 mm) including consolidation, finishing, curing etc.. complete as per specifications and drawings but excluding the cost of Form work shuttering, centering Complete at all levels

Extra for RCC Using Ready Mix Concrete from outside project area including transporting and pumping from approved batching plants .

Providing , centering ,shuttering Form work using PVC film faced plywood to get a neat form finish surface for all types of structures including necessary strutting, proping, staging, supports etc and deshuttering the same after the specified time all as per drawings, specifications and as directed by the Engineer-in-charge at all levels

For Sub Structure

For Super Structure

Providing and constructing Brickwork in cement mortar 1:6 using crushed sand with Flyash / Flyash Lime bricks with minimum 70 kg / Sq. cm strength of approved make and size in Sub structure including, scaffolding, raking out joints, curing, cleaning complete all as per specifications and drawings.

Demolishing Stone rubble masonry (In cement mortar) manually / by mechanical means carefully without damaging adjacent structures including stacking of serviceable materials and disposal of unserviceable materials within 100 m lead as per direction of Engineer-in-charge

Dismantling steel work in single sections including dismantling and stacking within 100 m lead In R.S Joists, Angles etc.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 100 m lead For thickness of tiles above 10 mm and up to 25 mm

Providing and grouting the joints of rubble stone pitching with cement mortar 1:3 and pointing the surfaces as directed complete as directed by the Engineer-in-charge

Dismantling barbed wire / flexible wire rope in fencing including making rolls and stacking within 100 m lead

Providing , designing and fixing of 3.00 mt Height fencing of Galvanized and Thermoplastic Powder coated welded mesh system with SS Concertina Coil and SS Barbed wire ( blades 316 and wire SS 304 ) , including PVC H shaped post with 4 mm dia. 358 weld mesh, panel height 2.456 m and width 2.488m with 4 V Bends etc. the fencing produced by electrical resistance welding of galvanized wires and subsequently thermoplastic powder coated as per follows.: Weld mesh Panels for the fence will meet the standards of EN 10223-7 with the following key specifications apart from the other points mentioned in the governing detailed specification: (Note: There is no existing Indian standards for Weld mesh panels for fencing Applications) Weld Shear strength: Minimum 50 % of the breaking strength of the smallest wire (In this case the vertical wire) Mesh Wire: Galvanized MS wire Specification for wire Diameter: IS 280 -2006 Tensile Strength of wire: Minimum 500 N/sq.mm Galvanizing of wire: 40 – 50 GSM as per IS 4826 (Measurement as per IS 6745) Uniformity of Coating: As per IS 2633 Adhesion test for coating: As per IS 6745 / IS 2629. Powder Coating on panels: The galvanized panels are subsequently Thermoplastic Powder Coated after welding with the thickness of minimum 250 Microns. Coating Standard: EN 10245-1/ IS 13871. Powder coating should withstand 1440 Hours of salt spray test Posts are `H' shaped post, MS material are then hot-dip galvanized to minimum 360GSM and then Thermo-plastic powder coated. Post will have with pre-welded base plate of minimum 400MPA strength using 8mm fillet weld, Base plate will have suitable holes to use SS316 M20*300mm Anchor bolts which will be installed at site with Glue for better strength. Powder Coating on post: The hot galvanized posts are subsequently Thermoplastic Powder Coated after welding with the thickness of minimum 250 Microns. Coating Standard: EN 10245-1/ IS 13871 Powder coating should withstand 1440 Hours of salt spray test , fencing system will have 600 mm dia. SS Concertina Coil (blade SS 316 and wire SS 304 ) having Tensile Strength of wire: 1400-1500 N/sq.mm, Blade Profile: FBBT, Blade Length: 66 mm, Center to Center Distance Between blades: 50mm Number of loops / coil: 56 Nos,. and 12 Swg SS304 Barbed wire. Total height of fencing to be 2.456 mtr (excluding concertina coil) and width 2.5mtr (posts c/c) as per the detailed drawing and specifications which shall meet the BARC technical specification as directed by the Engineer-in-charge at all levels. (Design, preparation of Shop drawings by the contractor as per the site conditions and the same shall be approved by BARC/Engineer in charge before procurement/execution of work.) Note : Test Certificate(s) for all material, coating . painting etc. to be provided by the bidder before and after execution of the work and the type test certificate should be from central electrochemical research institute.

Extra for each additional posts with accessories etc.as directed by the Engineer-in-charge at all levels for 3 m high fencing .

Providing 20 mm thick plastering using Ready mix external plastering compound of approved make for external faces of brickwork / concrete surfaces including preparation of the surface, curing, cleaning scaffolding up to 10 metres height complete.all as per specifications including forming drip moulds wherever necessary and as directed by the Engineer-in-charge

Providing Raised and cut pointing on stone with cement mortar 1:3 using river sand as per specifications and as directed at site by the Engineer-in-charge

Section-C : Electrical Works S&I Of Distribution Board

6 Way VTPN DB (RCBO as Incomer) as per TSS-1 I/C - 63A ,30mA,4Pole RCBO (1No) O/G- 32A ,TP MCB (02 Nos) O/G- 20A ,SP MCB (07 Nos) O/G- 6/10A ,SP MCB (05 Nos)

Lighting Fixtures as per TSS-2

20W LED Lighting Fixtures (Batten Type)

36W LED Lighting Fixtures (Recess Type)

36W LED Lighting Fixtures (Outdoor Type)

10W Surface mounted LED Fixtures

Light Point Wiring as per TSS-3

Primary Sw.box point (Average length-10Mtr)

Secondary Sw.box point (Average length-8Mtr)

Primary Light point (Average length-10 Mtr)

Secondary Light point (Average length-8 Mtr)

Ceiling Fan Point (Average length- 8 Mtr)

Exhaust Fan Point (Average length- 8 Mtr)

Power Point Wiring as per TSS-4

Primary Power Point

Secondary Power Point

Supply and installation of Fans as per TSS 5

1200mm Sweep Ceiling Fan

300mm dia Exhaust Fan

Removal , Shifting & Termination of Existing Cables of Barrier as per TSS 6

Supply and installation of cable including excavation as per TSS 7

Supply,installation,testing,commissioning of cable size 4c x 25Sq.mm in under ground /wall etc

Supply, installation,testing,commissioning of cable size 4c x 4.0/2.5 Sq.mm (copper) in under ground /wall etc

End Termination of Cable as per TSS 8

4c x 25Sq.mm

4c x 2.5Sq.mm

Supply & installation of FRP junction boxes for cable termination as per TSS 9

Earthing Station as per TSS 10

Copper Strips of Size 25x3mm thick as per TSS 11