GE(P)AF/GUR-33/2021-22 REPAIR TO DOOR VENTS PLASTERING FLOORING ROOFING AND REPAIR TO LIGHTENING PROTECTION WORK IN STORAGE SHED AT TECH AREA UNDER GE ( P) AF GURGAON

Amount

Schedule-A

Dismantling of brick work built in cement mortar including all qoins, arches, pillars, etc.complete all as specified and as directed by Engr-in-charge.

Demolition in cement concrete ground floor and paving nexc. 15 cm thickness ( below above ground floor ) complete all as specified and as directed by Engr-in-charge.

Taking down cement Plaster, any description on Brick Walls or on concrete Surfaces including raking out Joints, hacking for Key, scrubbing down with Water, etc., and removing same from the Site(s), complete all as specified and as directed by Engr-in-charge.

M&L for cement concrete type D-2 1:4:8 (40mm graded crushed stone aggregate as in foundation, filling and mass concrete complete all as specified and as directed by Engr-in-charge.

M&L for 75mm thick Cement concrete type D2 1:4:8 (40mm graded stone aggregate) as in sub base finished even smooth with broom finished w/o using extra cement, complete all as specified and as directed by Engr-in-charge.

M&L for 75mm thick Cement concrete type B2 1:2:4 ushing 40 mm graded stone aggregate) laid in alternate alternate panels for floor, path and harstanding complete all as specified and as directed by Engr-in-charge.

M&L for 25mm thick Wearproof topping using metallic floor hardener as per manfacutre's instruction, as specified (incorporating an approved metallic floor hardner), laid on concrete floors and pavings and path, and finished even and smooth (except metallic hardner) all as specified and directed by Engr-in-Charge. (Note metallic hardender glass strips area measured and paid separately).

Supply only 22 mm wide and 3 mm thick glass dividing strips as laid in floor all as specified and directed by Engr-in-Charge.

M&L for Brick work with sub class B bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 complete all as specified and directed by Engr-in-Charge.

All as per srl item No. 9 here in before but except bricks Note:- Serviceable bricks obatined from srl item No. 1 shall be re-used in srl item No. 10 after cleaning etc complete all as specified and directed by Engr-in-Charge.

M&L for for rendering 15mm thick in CM (1:4) on brick work or concrete surfaces other than fair face of brick work, finished fair & even w/o using extra cement all as specified and directed by Engr-in-Charge.

M&L for for rendering 10mm thick in CM (1:4) on or concrete surfaces, finished fair & even w/o using extra cement all as specified and directed by Engr-in-Charge.

M&L for preparing Newly Plastered Surfaces of walls, cornices etc and applying two coats weather proof paint over a Coat of approved primer, complete all as specified and as directed by Engineer-in-Charge.

M&L for newly plastered surfaces of walls and cornices and applying two coat of exterior emulsion paint over one coat of priming paint plaster coat in camouflage pattern all as specified and directed by Engineer-in-Charge.

Taking down Chowkhats or frames exc 2 sqm n exc 12 sqm each without taking of shutter from the frame all as specifed and directed by Engr-in-Charge.

Taking down existing bitumen felt roof treatment including cement mortar bedding and cleaning the surface and removal outside the MOD land, complete all as specified and directed.

M&L PCC (1:2:4) type B-1, using 20 mm graded mechanically crushed stone aggregates as in padding to roof to maintain the required slope and finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for water proofing treatment of roof consisting as under:- (a) Applying evenly a coat of bituminous primer conforming to IS-3384:1986 @ 0.30 litre/sqm including preparation of roof surfaces (b) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg/Sqm on plaster surface all as specified. (c) A layer of 3mm thick APP polymeric membrane of weight not less than 3.00 kg/sqm, reinforced with polyester non-woven fabric (weight not less than 160gm/sqm), duly sealed at over laps & joints with end laps of the 10cm and side over laps of 7.5cm by flame (by torch application) all as per manufacturer’s instructions, complete all as specified and directed.

Supply only water proofing liquid compoundcomplete all as specified and directed by Engr-in-Charge. :Make : DR. FIXIT PIDE PROOF LW, CICO, FOSROC.

M&L for Appling one coat Bitumen water proofing aluminium heat resistance paint on the roof as per manufacture instructions complete all as specified and directed by Engr-in-Charge. Make : PLASCON/PLASCON or equalant

M&L for 10mm thick cement plaster on brick work or over roof surface in CM (1:4) mixed with WPC as per manufacturer’s instructions @ 0.50% by weight of cement on concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note : WPC shall be measured and paid separately.

M&L PCC 1:2:4 Type B-0 using 12.50mmgraded stone aggregate as in roofs kerbs chajjas mud stops, rounded or camffered on edges with using watere proofing compound finishing faireven and smoot incding cutting groove in existing wall and makinggood wth cement motar in cm1:3 (water proofing compound shall bepaid seperately) complete all as sepcified and directedby Engr-in-Charge.

M&L PCC 1:2:4 type B1 using 20mm graded stone aggregate as in as in coping cill, rounded or chamffered on edges complete all as specified and directed by Engr in Charge.

Taking down mild steel door shutter exc 5 Sqm n exc 15 Sqm each, taking down exc hole fast and fixed new hole fast in PCC 1;1 -1/2:3 with hardner (DR FIXIT , CICO, FOSROC) and welding with column reinforcement and other and two door shutter including all necessery scaffolding and meachnical arrangement all as directed by Engr-in-Charge.

S&F polyester powder coated aluminium frame/chowkhat for door shutter of section 101.0x44.4 mm of gauge 16 fixed in brick masonery or conrcrete work by necessary drilling and rawl plug aggangement etc incl S&F polyester powder powder coated aluminium door shutter top rain and middle rail of section 85x44.4 of 16 gauge and bottom rail of section 150x44.4 mm 16 gauge (all section of such type having arrangement for fixing glass/prelaminated board on one or both sides as required) incl aluminium fittings such handle (2 Nos each shutter), tower bolt, locks (mortise type lock) glazing clips, rubber packing, anodised aluminium snap beading screw, hinges type B-21 150mm long (3 Nos each shutter) etc and one door stopper two legged with each leaf (shutter) complete (Glass and prelaminated board to be measured separately under appropriate item of sch A) complete all as specified and directed by Engr-in-Charge (Make of aluminium section shall be hindalco/Jindal)

M&L, for 5 mm thick aluminium sheet, exterior grade fixed between aluminium section with and including snap fitting aluminium clips of polyester powder coated along with rubber gasket, complete all as specified and directed by Engr-in-Charge. Note:- Rubber gasket shall be measured and paid separately.

M&L, for 12 mm thick pre-laminated particle board, exterior grade, pre-laminated on both side with decorative choice laminations fixed between aluminium section with and including snap fitting aluminium clips of polyester powder coated along with the glass with rubber gasket, complete all as specified and directed by Engr-in-Charge. Make. Anchor/Kitply/Novapan

S&F in repair powder coated aluminium grill DG 208 design as per approved pattern including aluminium beads etc complete all as specified and directed by Engr-in-Charge.

S&F in repair door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed all as specified and directed by Engr-in-Charge.

S&F in repair aluminium alloy door seal 1m long fixed to wooden doors complete all as specified and as directed by Engineer-in-Charge.

M & L for test point terminal block made of gun metal or phosphorus bronze /brass size (75 x 75 x10) mm drilled and 3 nos brass screwed 8 mm dia ,10 mm long hex.head screw complete including GI fabricated test point box size 150mm x 100mm x 75mm height with front openable made out of not less than 0.6 mm thick PGI sheet including painting and taking down old test point complete all as specified and as directed by engr- in charge.

Supply only porcelin viterous white/ brown/ green insulators of sizes 25mm x 25mm having provision of two holes for fixing on roof / wall under strip/ channel on top for running of down conductors to maintain gap between wall and down conductors etc complete all as specified and directed by Engr-in-Charge.

M&L in replacement for air terminatin single pointed aluminium rod 12mm dia and 300mm long including taking down old terminal complete all as specified and directed by Engr-in-Charge.

M&L for disconnecting, taking down of air terminal single pointed made of any material kept in safe custudy for roof repair and refixing the same in same or in other location including new nut, bolt and washers etc complete all as specified and directed by Engr-in-Charge.

M&L for replacement of U/s aluminium conductor steel reinforced any size and type of conductor and binding, fixing, interconnection with air termination at roof of open plinth/shade etc including taking down old U/s aluminium conductor complete all as specified and directed by Engr-in-Charge.

M&L for disconnecting, taking down old serviceable earth continuty conductor or main earthing lead fixed to wall/roof and connected air terminal to test point of any material or size, kept in safe custudy for roof repair and refixing the same in same or in other location including staples, GI wire, new nut, bolt and washers etc complete all as specified and directed by Engr-in-Charge. Note :- (i) Laying / fixing of strip from air termination to test point shall be in one run i.e. there shall be no joint in between air termination. In case joint is required, it shall be jointed with nut & bolt joint with breezing full contact of strip. (ii) Strip shall be fixed on insulator at the interval not more than 900mm in such a manner at any place it shall not touch to wall/ roof / any metalic body. (Cost of insulator shall be measured and paid seprately under respective items of Sch of works as supply only). (iii) Serviceable material to be re-used shall be kept in safe custudy under double lock and key one with deptt and one with contractor in the store made available inside technical area only.

M&L for earth continuity conductor or main earthing lead fixed to wall / roof and connecting air termination to test point with 25 x 4 mm aluminium strip including taking down existing aluminium strip complete all as specified and directed by Engr-in-Charge . Note :- (i) Laying / fixing of strip from air termination to test point shall be in one run i.e. there shall be no joint in between air termination. In case joint is required, it shall be jointed with nut & bolt joint with breezing full contact of strip. ii) Strip shall be fixed on insulator at the interval not more than 900mm in such a manner at any place it shall not touch to wall/ roof / any metalic body. (Cost of insulator shall be measured and paid seprately under respective items of Sch of works as supply only)

M&L for PCC 1:2:4 type B-1 using 20mm grade stone aggregate as in terminal GI pipe holding PCC blocks of size 25x25x25cm on roof or parapets of sheds including dismanteling of existing U/s block and removal of dismantled material complete all as specified and as directed by Engineer-in-charge.

Note The amount of Rs 66,000/- against Schedule of Credit on Page No 135 shall be deducted from the total amount quoted against Sch 'A' while deriving the Contract Sum for Acceptance

PAWAN KUMAR

Phogat Builders

M/S ujjwal associates

M/S PRADEEP ENTERPRISES

M/S Parshant Associates