IMPROVEMENT TO BHAIRAV MANDIR QUARTERS (PH II) AT AF STATION DEOLALI

Amount

B/R ITEMS Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as directed.

Demolition of cement concrete (unreinforced) in ground floors (below or above ground level ) not exceeding 15 cm thickness and including removing demolised PCC from site exc 500 mtr but nexc 1500 Mtr and depositing where directed

Demolition of reinforced cement concrete (Reinforcement cut as required to facililate demolition)) in ground floors (below or above ground level ) not exceeding 15 cm thickness all as directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc all as directed.

Material and labour for brick work with old size fly ash bricks straight or curved on plan to any radius, built in cement mortar 1:6 all as specified.

Material and Labour brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 all as specified & diretced.

Mild steel TMT 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

Material and Labour for reinforced cement concrete type B-1, 1:2:4 (using 20 mm graded granite stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and directed.

Material and Labour for reinforced cement concrete type B-1, 1:2:4 (using 20 mm graded granite stone aggregate) in chajjas , landings, balconies, canopies etc all as specified and directed.

Material and Labour for use and waste of fair finished flat form work to soffits of suspended slabs such as roof slabs, floor slabs, cooking platform and similar work not exc. 200 mm thick all as specified and directed.

Material and Labour for use and waste of rough finished form work to edge of concrete slabs, breaks in floors, etc exc 5 cm but not exc. 10 cm wide all as specified.

Material and Labour granite (of any type) work ( table rubbed & polished), 18 to 20mm thick, in steps, jambs, pillars, window-cill, cooking platforms & like in cement mortar (1:4) including polishing of chamfered edges and pointing in white cement using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed bed in CM (1:6) necessary cutting, notching etc for sink all as specified and directed.

Material and Labour Machine cut cudappah stone slab 20mm to 25 thick, over and including cement screed bed in CM 1:6 laid and jointed in grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete necessary cutting, notching etc for sink all as specified and directed.

Material and Labour for Chamfer, splays, or arris in facework of cudappah stone exc 15mm wide but nexc 50mm wide complete all as specified and directed.

Material and Labour for drilling holes for pipes etc in cudappah including RCC slab not exc. 40mm dia and not exc. 100 mm depth all as directed.

Material and Labour for plain cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate ) 25 mm thick as in flooring finished even and rough all as specified and directed.

Material and labour for joint free non-skid ceramic coloured tiles 7 to 8 mm thick (square / rectengular) area of each tile exceeding 0.11 sqm but not exc. 0.18sqm , laid in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match with over and including cement mortar screed of 15mm thick in CM 1:6 all as specified and directed.

All as per item No. 17 above here-in- after but vertical surfces over 10mm thick rendering in CM 1:4 all as specified and directed.

Material and Labour for coloured join free glazed ceramic tiles 450 x 300 x 6 to 7 mm thick on vertical surfaces such as skirting/ dado , set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tiles over and including 10mm thick rendering/bedding layer in CM 1:4 on brick work /stone masonary or concrete surfaces all as specified and directed.

Material and labour for 18-20 mm thick Kota stone tiles (Pre-mirror polished), in riser of steps, skirting,dado etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles including rounding the edges of kota stone over and including 10mm thick backing coat in cement mortar (1:4), surfaces finished even and rough to receive tiles, all as specified and directed.

Supply and Fix in repair Vitreous China Squatting pan, Orissa pattern, size 580 x 440 mm white with `P' or `S' trap, front or back inlet and integral foot rests including connection to trap, to flushing pipe etc. complete including PCC for making good to floor etc all as specified and directed.

Supply and Fix in repairs 10 liters PVC valveless symphonic action type flushing cistern high/low level, white complete with inlet, ball valve, float and handle including brackets and telescopic down pipes and joint with WC complete all as specified.

Supply and Fix PVC connection 15 mm bore size with PTMT nuts and PVC washers of length 450 mm all as specified and directed.

Disconnecting existing tanks of capacity 1000 ltrs, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required re-connecting and re-fixing in position all as directed.

Material and labour for rotational moulded polyethylene water storage tanks 1000 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling the old one as directed complete. complete all as specified and directed .

Supply and Fix ball brass valves, high pressure, with polythene float and fly nut for 20mm bore dia pipe compelet screwed for iron pipe or brass ferrule and fixed.

Taking up or down steel water tubing and connections for 20mm bore complete all as specified and as directed

Re-fixing 20mm dia old steel water tubing after cleaning and connecting in new or old position with and including new fitting (ISI marked) complete all as specified and as directed

Material and Labour GI tubes medium grade 20mm bore fixed to wall ceiling or laid in floor with and including all fittings (ISI marked). complete all as specified and as directed.

Taking up or down GI tubing 15 mm bore and connections from walls and ceilling or laid in floorall as specified and directed.

All as per item No. 28 here-in-before but of 15 mm bore.

All as per item No. 29 here-in-above but of 15 mm bore.

Material & labour for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing and making good cutting not exc 10 cm girth complete all as specified and as directed.

Supply and fix in repairs 15 mm bore gun metal, globe or gate valve cast copper chromium plated fancy type with iron wheel head , screwed both ends for iron pipe with crutch or buttrtfly handles all as directed.

All as per item No. 34 here-in-before but of 20 mm dia.

Supply and Fix in repair 15 mm bore fancy type chromium plated bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of approved make and all as directed.

Supply and fix stop cock in repairs of 15 mm bore, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of approved make and all as directed.

Supply and Fix in repairs brass Chromium plated shower rose 75 mm dia with CP arms with swivel joints, including fixing to steel pipe or union all as specified and directed.

Supply and Fix in repairs wash hand basins, vitreous china( flat back) white of size 550mm X 400mm including cutting for and pinning in ends of brackets or erecting stand including brackets & waste coupling fitting, brass chromium plated 32 mm size with long screwed shanks and fly nuts and including PVC discharge pipe as specified and as directed.

Supply and Fix in repairs 15 mm bore Fancy type pillar taps, cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed.

Supply and Fix low density polythelene pipes 40 mm bore fixed complete to walls, ceiling or in floor of pressure rating 6 Kgf/ Sqcm all as specified and directed.

Material and Labour for cutting holes into or through brick/stone walls built in cement mortar, superficial area nexc150 Sq cm and making good in cement mortar 1:3 or PCC 1:2:4: type B-1 complete all as specified and directed.

Supply and Fix Sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers; including waste coupling with pipe, bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 495 mm x 420mm bowl size 410mmx330mmx160mm of approve make complete all as specified and directed.

Supply and Fix in repair PVC (SWR) floor trap of 75 mm outlet plain with grating including jointing with solvent cement of approve make complete all as specified and directed

Supply and Fix 75mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches including digging and making good as existing complete all as directed.

Supply and Fix in repairs brass chromium plated tubular towel rail, 20 mm dia., D Type, 60 cm long between flanges all as directed.

Supply and Fix sheet glass shelf assembly consisting of 5.5mm thick glass shelf 12cm wide with fixing and including chromium plated bracket, guard and railing 55/56cm long complete all as specified and directed.

Supply and Fix aluminium Hat pegs, solid body, 125mm to 175 mm all as directed.

Taking down cement plaster on brick/stone walls/ concrete surface etc including raking out joints, hacking for key, scrubbing down with water etc all as directed.

Material and Labour for rendering 15 mm thick on stone masonry surfaces or other than fair faces of brick work of walls in cement mortar 1:6 finished even and fair all as specified and directed.

Material and labour for rendering 15mm thick plaster on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement all as specified and directed.

Material and labour for rendering 5mm thick plaster on fair faces of brick work or concrete surfaces in CM 1:3 finished even and smooth without using extra cement on ceiling as specified and directed.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of cement based paint over one coat of alkali resistant priming paint all as specified and directed.

Material and labour for preparation of newly plastered surfaces of walls applying two coats of weather proof paint (APEX paint or equivalent as approved) over one coat of alkali resistant priming paint all as specified and directed.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion over chalk whiting on plastered surfaces all as specified and directed.

Material and labour for preparation of old surfaces of walls by brooming down or by steel wire brushing and applying one coat of cement based paint all as specified and directed.

Material and labour for preparation of newly plastered surface and applying three coats white wash on ceiling all as specified and directed.

Material and labour for complete removal of existing treatment of ceiling by steel wire brushing, preparation of surfaces and applying three coats of white wash on ceiling all as specified and directed.

Material and labour for complete removal of existing treatment of walls by steel wire brushing, preparation of surfaces and applying two coats of distemper oil emulsion over a coat chalk whiting all as specified and directed .

Material and labour for complete removal of existing treatment of walls by steel wire brushing, preparation and applying two coats of cement based paint over one coat of alkali resistant priming paints all as specified and directed.

Taking down chowkats with shutter (without taking off shutter from the frame) not exc 1.5 Sqm each all as directed

All as item 62 herein before but exc 1.5 sqm but not 4 Sqm each

Cutting holes in stone walls built in cement mortar for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B1exceeding one brick wall and not exceeding two brick walls all as specified and directed.

Supply and fix pressed steel frame made out of 1.25 mm thick M S sheet and of size 105 x 60 mm for doors/ windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., and filling with PCC 1:3:6,type C-0 using 12.5 mm graded stone aggregate and painting with two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete, as specified and directed.

All as per item No. 65 here-in-above but of size 125x60mm

Material and Labour for 35 mm thick second class hard wood plain framed factory made panlled shutters( two panels) with 12 mm thick veneered particle board with commercial face veneers on both side as panel inserts, styles & rails shall be of second class hard wood timber generally conforming to IS-1003(Part-I) (Door shutters) Kiln seasoned and chemically pressure treated and fitted to chowkats all as specified and directed.

Supply and Fix 35 mm thick second class hard wood factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc; sizes of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) and fitted to chowkats complete all as specified and directed.

Supply and Fix steel windows with side hung shutters including box type hinge of size 75 mm with 'z' type steel handle and steel peg stay and 02 No.100 mm size MS tower bolts welded on each shutter complete with glazing bars, dovetailed or welded complete all as specified and directed.

All as per item No.69 above here-in- after but without glazing bars.

Supply and Fix steel ventilators` with top hung shutters with glazing bars including box type hinges of size 75 mm with 'z' type steel handle and steel peg stay complete all as specified and directed.

All as per item No. 71 above here-in- after but without glazing bars.

Supply and Fix window guard bars welded in steel window/fixed independently in wooden frame conforming toFe-290 Gde E-165 complete all as specified and directed.

Supply and Fix factory made solid panel PVC door frame of size 50mmx47mm out of 5mm wood grain printed PVC sheet & edges will be printed to match with printed sheet reinforced with M.S. square tube, complete all as specified and directed.

Supply and Fix factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strips of 20 mm width stuck inside with solvent cement for stiles and single sides prelam PVC sheet and stile & rails having one side feathered edge and on other side 10mm (90°) bent edges & as gap insert for top rail & bottom rail; Panelling to be fitted in the M.S. frame welded/ sealed to the styles & rail with suitable PVC sheet beading, and joint together with solvent cement, all as per specification and as directed.

Supply and Fix 3mm thick sheet glass ordinary quality and glazing with oil putty not exe 0.5 sqm in each pane complete all as specified and directed.

Supply and Fix 3mm thick frosted glass ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane all as directed.

Supply and Fix stainless steel wire cloth, 0.36 mm dia of wire and average width of aperture 1.4 mm and fixed with stainless steel wire staples including necessary wooden/steel beading as required complete all as directed.

Material and Labour for preparation of new wooden surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material and Labour for preparation of new steel surfaces of any desciption over 10 cm in width or girth not other wise described and applying two coats of synthetic enamell paint over a coat of red oxide zinc chrome primer all as specified and directed.

Supply and Fix 100mm long Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed type B-21 all as specified and directed.

Supply and Fix 150 mm size aluminium anodised barrel tower bolt of extruded section all as specified and directed.

Supply and Fix 250 mm Aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) & fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed all as specified and directed.

Supply and Fix aluminum anodized handle cast type 150mm size all as specified and directed.

Supply and Fix in repairs mild steel ordinary rat tails 300 mm size pattern springs including roller and roller plate complete all as specified and directed.

Supply and Fix in repairs 140mm length floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor all as directed.

Material and Labour for 75 mm thick sub base in PCC 1:4:8 type D-2 (using 40 mm graded stone aggregates) all as specified.

Material and Labour Chequered cement concrete tiles rubber moulded 25cm x 25cm x 25mm thick, set, jointed and pointed in near cement slurry in floors, with grey cement and pigments over and including 15 mm thick screed bedding in CM 1:6 all as specified and as directed.

Material and Labour for plain/reinforced cement concrete Type B-1, 1:2:4 (using 25 mm graded granite stone aggregate) cast in situ in copings, bed plates and the like including weathering, slightly rounded or chamfered angles & throating and including use of form work complete all as specified.

Material and Labour for precast reinforced cement concrete 1:2:4, type B1 (Using 20 mm graded granite stone aggregate) in landings, cover slabs (for drian making holes .) shelves and similar articles with plain faces and set in cement mortar 1:4 including mouldings/formwork all as specified and as directed.

Supply and Fix pre coated curtain rod 25mm dia fixed with fancy type matching pair of a brackets fixed with screw as approved and as directed (Note; Brackets for this item will be measured separately as supply only)

Supply only fancy brackets to suit pre coated curtain rod 25mm dia as approved.

Supply and Fix in repair stainless steel kitchen plate rack of 1 mm thick of size not lessthan 900 mm x 750 mm fixed with stainless steel screw all as specified and directed.

Material and Labour 75 mm thick PCC type C-2 , 1:3:6 (using 40mm graded stone aggregates) as in plinth protection and surface finished even and fair and the PCC should be laid in alternate ways after every two meters and cut with a groove as per direction of Engineer-in-Charge complete.

Material and Labour for 100 mm thick Plain cement concrete type B-2, 1:2:4 (using 40 mm graded stone aggregate) as in hardstanding/floor all as specified and directed.

Taking down eaves gutters and rainwater pipes (in any size & pattern), including all fittings, heads, shoes, bends, swan-necks etc all as directed.

Supply and Fix PVC (SWR) pipes, single socketed, in any length, with rubber rings 110 mm dia in floor/wall all as directed.

All as per item No. 97 here-in-before but of 75 mm dia.

Supply and Fix PVC (SWR) floor trap 100 mm bore plain with grating including jointing with solvent cement of approved make all as specified and directed.

Supply and Fix PVC (SWR) bends 110 mm dia with access door as specified.

Supply and Fix PVC (SWR) bends 75 mm dia with access door as specified.

Supply and Fix PVC (SWR) bends 110 mm dia as specified.

Supply and Fix PVC (SWR) bends 75 mm dia all as specified.

Supply and Fix PVC (SWR) vent cowl 110 mm dia all as specified.

Supply and Fix PVC (SWR) vent cowl 75 mm dia all as specified.

Demolition of cement concrete other than ground floors and in sunken portion including WC, IWC ,floors traps etc all as specified and directed.

Material and Labour rendering 15 mm thick on brickwork or concrete surfaces in CM 1:3 with using water proofing compound all as specified and directed. Note:- Water proofing compound shall be measured and paid separately as supply rate only.

Material and labour for PCC 1:5:10 type E2 (using 40mm graded stone aggregate) as in filling of sunken portion all as specified and as directed.

Material and Labour for plain cement concrete Type D-2, 1:4:8 (using 40 mm graded granite stone aggregate) in flooring, filling and mass concrete all as specified and directed.

Taking down carefully existing bitumen tar felt including plaster/existing PCC padding, wire brushing and cleaning of the surface of roof, terraces including flashing and junctions of parapets/ Kerbs, walls etc and removing off the rubbish to a distance exc 500m but n.exc 1.5km and depositing all as directed.

Material and Labour for 25 mm thick PCC (1:2:4) type B-0 (using 12.5 mm graded crushed stone aggregate) as in roof pading complete all as specified and as directed.

Material and Labour for 10 mm thick bedding layer in CM (1:4) on concrete surfaces (When concrete is green) mixed with WPC liquid @200ml/50Kg bag of cement , finished the surfaces fair and even complete all as specified and directed. Note : WPC shall be measured and paid separately.

Material and Labour for plain, cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges including necessary formwork complete all as specified and directed.

Supply only liquid approved water proofing compound

Material and Labour for cleaning the newly plastered surfaces thoroughly with wire brushes and providing water proofing treatment all as specified here in after :- (a) Bituminous primer @ 0.30liter per sqm conforming to IS 3384-1986 (b) 3mm thick APP polymeric membrane minimum weighing 3 Kg/Sqm of M/S TEXSA Ltd or M/S TIKI Asphalt hydro stop or IWL 3.00kg/sqm membrane (one layer) laid by torch application method with over laps of 100 mm joints of traverse direction and 75 mm at longitudinal direction duly thermofused by flame torch all as specified in application manual of the company c) Painting with one coat of bitumin grade 85/25 @ 1.2 Kg/Sqm. (d) Applying two coats of aluminium paint @ 100ml/Sqm

Excavation in trenches not exc 1.50m wide and not exc 1.50m deep for foundation and getting out in any type soil all as specified.

Returning, filling in, excavated soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm in any type of soil

Removing excavated material exc n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point

Material and Labour for plain cement concrete 1:4:8 type D2 as in bed to drain pipes of 150mm dia including packing under and haunching against the sides of pipes after they are laid and tested all as specified.

Material and Labour for providing salt glazed stoneware grade 'A' drain pipes of 150mm dia laid in trenches and jointed as specified and directed.

Material and Labour for 15 mm thick rendering in CM (1:4) on brick wall mixed with WPC 200ML liquid @200ml/50Kg bag of cement , finished the surfaces fair and even complete all as specified and directed. Note : WPC shall be measured and paid separately.

Material and Labour for extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc all as specified and directed.

Cutting into existing manholes for 150mm dia pipes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required all as specified.

E/M ITEMS Taking down carefully copper/aluminium point wiring (light, fan, socket or power etc) on TW batten/PVC casing caping, steel surface /PVC conduit including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Material and labour for point wiring with two single core, PVC insulated, unsheathed, multi stranded bright annealed copper conductor cable, 1.5 Sq.mm 1100 Volts, FR grade drawn through and including heavy duty PVC casing and capping not less than 25 mm width and accessories surface mounted on walls, ceilings etc. on & including PVC box and plate for mounting switches, sockets, regulators etc and one run of 1.5 Sq.mm PVC insulated, unsheathed, multistranded, copper conductor cable FR grade as earth wire and connected to common earth dully complete for one light/ fan/ bell point all as specified and directed complete.

All as per item no. 125 hereinbefore but for one 3 pin socket out let 5 Amps on independent board.

All as per item no. 125 hereinbefore but for one 3 pin socket out let 5 Amps on same board.

All as per item No 125 herein before but two runs of copper condutor of size 2.5 sqmm as in socket outlet / power point 15 Amps.

Supply and fix switch piano type flush button 5 Amps single pole one way all as specified and all as directed.

Supply and fix switch piano type flush button 15 Amps single pole one way all as specified and all as directed.

Supply & fix socket out let 2 in 1, 5 pin 5 Amps flush type complete all as specified and as directed.

Supply & fix socket out let 2 in 1, 3 pin 5 and 15 Amps flush type complete all as specified and as directed.

Supply and fix in repairs lamp holder PVC/ Polycarbonate type with back plate suitable for batten fitting Single Phase AC 230 Volts complete all as directed.

Supply and fix in repairs ceiling rose of 3 phase/PVC/ polycarbonate, insulated body 65 x 50mm two or three terminals all as directed.

Supply and fix Bell push 5 Amps SP one way suitable for 230 Volts flush type all as specified.

Supply and fix electric bell Ding Dong AC 230 volts single pole all as specified.

Supply and fix in repairs Fan regulator electronic solid state with various steps variable speed suitable for ceilling fan of size 900 to 1500mm sweep working on 230 V AC supply with all necessary connections all as specified.

Supply & fix in repair decorative ultra slim square profile linear LASER RAY lighting fixture extrudedpolycarbonate, environmental friendly, energy efficient ready to use pack 20W LED 6000K, complete all as specified and as directed by Engineer-in-Charge. Make: Crompton, (CAT No.LDLSR20-CDL) or equivalent in Philips/Bajaj/Havells/Wipro as approved.

Supply & fix in repair decorative ultra slim square profile linear LASER RAY lighting fixture extrudedpolycarbonate, environmental friendly, energy efficient ready to use pack 10W LED 6000K, complete all as specified and as directed by Engineer-in-Charge. Make: Crompton (CAT No.LDLSR10-CDL) or equivalent in Philips/Bajaj/Havells/Wipro as approved.

Supply and fix in repairs sheet metal enclosure MCB SPN distribution board 8 way 240 volt, double door with DIN rail bus bar, neutral link, earth terminal etc IP-43, IK 09 protectionall as specified and directed. Make :- Legrand cat No. 607711 or equivalent in specified makes as approved.

Disconnect and insulate electric supply wire and taking down carefully ceiling fan of any make 1200 mm sweep,dismantling and opening for checking the bearing, bushes overhauling including oiling, greasing, replacement of cotter pins, including scrapping the old existing paint and painting with two coats of synthetic enamel paint over one coat of red oxide primer, writing the MES No.and replacement of flexible cord size 23/0.0076 and rubber bushes etcand hanging the ceiling fan to its orignal position by connecting with new 3 core copper conductor cable PVC insulated and sheathed, from ceiling rose to fan connector including replacement of clamps rubber shackle and fixed with necessary bolts , nuts,washers, etc., including testing completeas directed. Note: Replacement of winding measured separately

Material and labour for fixing in repairs of MCB SP 6-32 Amp all as specified.

Material and labour for fixing in repairs of MCB SPN 6-32 Amp all as specified.

Supply, laying, testing and commisioning of LT XLPE insulated/PVC heavy duty armoured cablle 1100 volts grade UG stranded aluminium conductor electric cable cross sectional area 35 Sqmm 3.5 Core including necessary connection with provision of lugs & cable gland fixing arrangements all as specified and directed.

Supply, laying, testing and commisioning LT XLPE insulated/PVC heavy duty armoured cablle 1100 volts grade UG stranded aluminium conductor electric cable cross sectional area 6 Sqmm 2 Core including necessary connection with provision of lugs & cable gland fixing arrangements all as specified and directed.

Material and labour for taking down indoor Distribution board after disconnecting the electric supply by taking all precaution all as specified and directed.

Supply, install, testing and commissioning of cubicle type indoor LT distribution panel fabricated out of 2.00 mm thick CRCA sheet with separate locking arrangement, painted with epoxy powder coated over a coat of red oxide primer, factory made, cubical type, double door hinged type, one side openable, air fins for ventilation, provided with necessary installation for mounting electrical accessories, holes for cable entries, space for fixing electric meter, detachable gland plates at top and bottom, earth connection terminals etc. and mounted on 50x50x6 mm size angle iron frame, duly painted with anticorrosive paint, adebquete clearence from wall for the entry and exit of cable, provision of ventilation on sides, manufacturer details, necessary cement work for grouting and provn of cable lugs complete and consisting of following all as specified and directed. (a) MCCB DB 8 way with and including MCCB 3 pole 160A of 25 KA - 1 No and going SPN-32A MCB - 10 Nos. (Model No. DBPGL008DD of L & T or equivalent in specified makes) (b) MCB 'C' curve SP-32A with enclosures near electric meter on going circuit - 9 Nos.

Material and labour for providing earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 metres deep below ground level) surrounded with alternate layer of charcoal and salt of 15 cm thick, 3 feet x 3 feet all around the electrode as directed with top edge of the plate not less than 1.5 mtres below normal ground level,

connected to galvanised earth strip of size 25 x 4.0 mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 connected to earthing test point all as specified or indicated including testing on completion including earthing pit in PCC 1:3:6 type C-0 & 40mm thick precast RCC cover in 1:2:4 type B1 reinforced with 8mm dia TMT bar @ 75mm c/c both ways with 02 Nos lifting handles of 12mm dia MS plain bar, GI pipe 20mm dia light grade with funnels & wire mesh for watering and 40mm dia light grade GI pipe for earth lead protection etc including necessary excavation and earth work in any type of soil complete all as specified and as directed. Note:- GI strip and protection pipe upto 7.5mtr is deemed to be included in the quoted rate.

Excavation in trenches n. exc 1.5 Mtr wide and n. exc 1.5 mtr in depth and getting out soft/loose type soil all as specified.

Excavation in trenches n. exc 1.5 Mtr wide and n. exc 1.5 mtr in depth and getting out in hard/dense soil all as specified.

Returning, filling in and ramming with excavated soil, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick all as specified.

Removing excavated material to a distance not exc.50 metres and depositing where directed at a level not exceeding 1.5 mtr above the starting point all as specified and directed.

M&L for river sand filling completely dry for cushioning to U/G cable laid in trenches, 8cm below the cable and 15 cm above the cable and punned down to a total thickness of sand 18 cm complete all as specified and directed, with good quality of sand all as specified and directed Note: Punned thickness only will be measured and paid.

Supply & lay un-reinforced precast, concrete cable cover, class LV type I flat size 250mm x 150mm x 40mm for cable protection all as specified.

Supply and laying, fixing, in repairs tube galvanised light grade with all fittings laid in tenches/Fixing on wall/pole including fixing arrangements of size 40 mm bore all as specified and directed.

Suplly & fix exhaust fan AC single phase 230Volt of size 300mm sweep with lauvers,in metallic body with powder coated paint, AC single phase 230V capacitor run motor, including lauvers/shutters and connecting up 3 core flexible cord of size 23/0.0076mm from ceiling rose to exhaust fan including cutting suitable opening in wall and making good of disturbed surface complete all as specified and as directed. Make : Crompton Cat No. :EXHD300-4-1 or equivalent in Bajaj/Phillips.

Supply & fix in repair circular LED flood light with tapered fin design & excellent thermal management along with IP66 protection OMEGA, lighting fixture extrudedpolycarbonate, environmental friendly, energy efficient, complete all as specified and as directed. Make: Crompton (CAT No.LFLN11-70-CDL/60) or equivalent in Philips/Bajaj/Havells/Wipro as approved.

Suplly & fix Bulk head fittings environment friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head edge-lit LED luminaire comprising of high brightness LEDs,complete all s specified & as directed. Make: cat no.RUGBYNEONFT10WLED860SSYMTOPC or equivalent of Crompton/Wipro/Bajaj as approved.

Note:- The amount of schedule of credit on page No. 43 shall be deducted from the amount quoted against sch 'A' while deriving at the contract sum for accptance.

N.U. MIRZA

M/S SANJAY B SHARMA

M/S PRAMOD SURESHCHANDRA AHER