Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Tender Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹44.5 LAccepted-AOC | L1 | Accepted-AOC Reasonable rate | |
| 2 | L2₹46.6 L+₹1.0 L (2.22%)Rejected-AOC | L2 | Rejected-AOC Quoted amount are higher than L1 | |
| 3 | L3₹46.8 L+₹1.2 L (2.66%)Rejected-AOC H NO 400 FLAT NO 13 A SEMATILLA DIMAPUR 797112 NAGALAND | DIMAPUR | DIMAPUR | NAGALAND | 797112 | L3 | Rejected-AOC Quoted amount are higher than L1 | |
| 4 | L4₹47.2 L+₹1.6 L (3.46%)Rejected-AOC | L4 | Rejected-AOC Quoted amount are higher than L1 | |
| 5 | L5₹48.6 L+₹3.0 L (6.65%)Rejected-AOC | L5 | Rejected-AOC Quoted amount are higher than L1 |
Tender Value
₹45.0 L
EMD Value
₹89,940
Closing Date
23 Sept 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE 868 EWS
GE 868 EWS PIN- 913 868 C/o 99 APO
SPL REPAIR TO BLDG NO T 25/31A CHDH OF (TA) JAT PROVN OF HARD STANDING NEAR VEH WASHING PT OF MT AREA OF XXX ENGR REGT AND ADDN/ALT OF BLDG NO T 13 OF FRW
2023_MES_615080_1
8575/C/E8
Open Tender
Civil Works
Item Rate
180 days
RANGAPAHAR
Class D, Category a(I)
2 documents required · 2 mandatory
₹500
GE 868 EWS
₹89,940
19 Oct 2023
22 Aug 2023
26 Sept 2023
22 Aug 2023
23 Sept 2023
4 Sept 2023
22 Aug 2023 - 29 Aug 2023
Amount
Demolition of plain cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) etc complete all as specified and directed.
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing unserviceable tiles to store and rubbish off the premises etc complete all as specified and directed.
Taking down chowkhat or frames not exc 1.5 Sqm each (without taking off shutter from the frame) etc complete all as specified and directed.
Taking down chowkhat or frames exc 1.5 Sqm but not exc 4 Sqm each (without taking off shutter from the frame) etc complete all as specified and directed.
Dismantling timber scantlings unframed work 40 sqcm and over in section in any position complete all as specified and directed.
Demolition of reed, lathing single or double, including battens and plaster or chicken wire lathing complete all as specified and directed.
Dismantling Asbestos cement sheet (Corrugated, semi corrugated etc ) in roof covering complete all as specified and directed.
Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) any thickness including cover fillets complete all as specified and directed.
Dismantling boarding any description fixed in any position with nails complete all as specified and directed.
Dismantling of wrought iron or mild steel work of any description etc complete all as specified and directed.
Roughening surface of old concrete floor by picking ,sweeping clean and washing down with water to remove dust etc complete all as specified and directed.
M & L for chequered cement concrete tiles of Size 25mm thick any description jointed and pointed in neat cement slurry in floors with grey cement and pigment laid over and including 20 mm thick screed bed or bedding layer of mortar in CM (1:6) etc complete all as specified and directed.
M & L for PCC (1:4:8) type D-2, 100 mm thick (using 40 mm graded stone aggregate) as in sub base etc complete all as specified and directed.
M & L for coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) in section exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles etc complete all as specified and directed.
All as per Item No. 14.00 here-in-above but on vertical surfaces such as skirting , dado risers to steps over and including 10 mm thick bedding layer in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles etc complete all as specified and directed.
M & L for coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) in section exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor laid over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured ceemnt to match the shade of tiles etc complete all as specified and directed.
All as per Item No. 16.00 here-in-above but on vertical surfaces such as skirting , dado risers to steps over and including 10 mm thick bedding layer in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles etc complete all as specified and directed.
M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles , laid over and including 10mm thick CM (1:4) backing coat etc complete all as specified and directed.
M&L for Glazed ceramic tiles in vertical surface 300x 200x 7 mm/ thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick CM (1:4) backing coat etc complete all as specified and directed.
M&L for Granite (of any type) tiles 18-20mm as in platform thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing with nosing over 20 mm screed bed in CM 1:4 complete all as directed by Engr-in-Charge.
M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbingn and polishing laid over and including 20 mm thick screed bed in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including rubbing/grinding and polishing including Dismantling etc complete all as specified and directed.
S & F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.
S & F Pre-painted galvatume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.
M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe 410 -W (Gde-E- 250) quality-A etc complete all as specified and directed.
S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade st-240 including one shop coat of zinc chromate primer paint including preparation of surface etc complete all as specified and directed.
S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410 -W (Gde-E- 250) quality-B etc complete all as specified and directed.
S&F mild steel screw bolts (machine made) dia 16-20 mm and length 15 to 22.5cm length with hexagonal or square heads at one end or screwed the other or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut etc complete all as specified and directed.
S&F 2nd class hard wood scantling as in framed work etc clean sawn complete all as specified and directed.
All as per Item No. 28.00 here-in-above but except timber complete all as specified and directed.
S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-painted self embossed, textured designer board E-Board Classic to be fixed or laid with GI frame grid/section size 600mm x 600mm with main runner 38x24x0.9 mm thick, cross tee 8.6x24x0.9mm and wall angle 19 x19x0.9mm duly suspended with 4mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size etc complete all as specified and directed.
M/L for 25mm thick and 200 mm width second class hard wood boarding , plained one side with butt joints as in eaves boards complete all as specified and directed.
M/L for 75 mm thick PCC (1:3:6) type C-2 , using 40 mm graded stone agg in plinth protection/aprons/path laid to slope of 1:12, finished fair and even without using extra cement with and including all necessary formwork to divide tha area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 10 mm wide joints throughout thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) etc complete all as specified and directed.
M&L for 2nd class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pined joints complete all as specified and directed.
M&L for factory made 35 mm thick 2nd class hardwood plain framed pannelled shutter (any number of panels) with panels of timber flat on both sides , supplied and fitted to chowkats complete all as specified and directed.
M&L for factory made 35mm thick 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(a) etc complete all as specified and directed.
M&L for factory made 30mm thick 2nd class hard wood Glazed and skelton window and ventilator shutter, open rebated and prepared to receive glass, gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated without sash bars edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b) etc complete all as specified and directed.
S & F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as specified and directed.
S & F butt hinges medium grade cold rolled mild steel and fixed size of hinges 100 mm long size etc complete all as specified and directed.
S & F butt hinges, medium weight 75 mm long size etc complete all as specified and directed.
S & F Aluminium anodised barrel tower bolt of extruded section and fixed 100 mm long etc complete all as specified and directed.
S & F Aluminium anodised barrel tower bolt of extruded section and fixed 200 mm long etc complete all as specified and directed.
S&F 150mm long aluminum hook and eye, complete all as specifed and directed.
S&F Aluminium handle cast type anodised 150 mm long etc complete all as specified and directed.
S&F 150 mm long aluminium anodised Tower bolts etc complete all as specified and directed.
S&F 100mm long aluminium anodised handles cast copper etc complete all as specified and directed.
S&F 125mm size aluminium handles,cast type,anodised all as directed complete all as specified and directed.
S & F Aluminium alloy anodised sliding door bolt with hasp and staple (bolt type fixing clips of sheet cast or extruxded section(300 mm long) etc complete all as specified and directed.
S&F 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete specified and directed
S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm etc complete all as specified and directed.
S&F 3 mm thick Figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 sq. m in each pane etc complete all as specified and directed.
S&F 3 mm Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane etc complete all as specified and directed.
M&L for RCC Beams, cantilevers, bressummers, lintels over 1.5m span using RCC Type B-1 (1:2:4) (using 20mm graded stone aggregate) etc complete all as specified and directed.
M&L for RCC (1:1.5:3) type A-1 (using 20mm graded stone aggregate) in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like etc complete all as specified and directed.
S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with etc complete all as specified and directed.
S&F MS TMT bars 6 mm to 8 mm dia cut to length, bent to shape reqd incl cranking, bending and binding with MS wire n.exc 0.90 mm dia (annealed) for stirrups/binders etc complete all as specified and directed.
Use and waste for formwork to chullah hoods, cha jjas, troughs and similar items for rough finished to surfaces in cluding edge etc complete all as specified and directed.
Formwork to sides and soffits of lintels, cantilevers for rough finished to surfaces etc complete all as specified and directed.
Taking down cement plaster on brick walls including raking out joints hacking for key, scrubbing down with water etc complete all as specified and directed.
Demolition of brick work built in cement mortar incl all quions, arches pillars etc but excl ashalar facing etc complete all as specified and directed.
M&L for brick work with sub class B bricks using old size burnt bricks straight or curved on plan exc 6 m mean radius in CM 1:6 etc complete all as specified and directed.
M&L for brick work with sub class B bricks using old size burnt bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 etc complete all as specified and directed.
S&FGI wire netting 0.71 mm dia and 12 mm mesh lathing in to reed and bird proofing in walls incl all laps cutting and waste complete all as specified and directed.
M&L for 15mm thick plastering in CM (1:4) on one side of lathing in two separate layers even and smooth without using extra cement complete all as specified and directed.
M&L for 10 mm thick plastering in CM (1:6) on the other side of lathing finished even and smooth without using extra cement complete all as specified and directed.
M&L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 using water proofing compound @ 3% by wt of cement for finished even and smooth (without using extra cement) (WPC will be measured and paid separately) etc complete all as specified and directed.
Supply only Integral water proofing compound etc complete all as specified and directed.
M&L for rendering 15mm thick in cement mortar (1:6) on fair faces of brick or concrete work even and smooth without using extra cement etc complete all as specified and directed.
M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces of Cement Plaster (1:6) on internal surface etc complete all as specified and directed.
M&L for applying two coats of oil bound distemper on new plastered surfaces of walls including preparation of surface and applying one coat of primer, on plastered surfaces, preparatory to distempering complete all as specified and directed etc complete all as specified and directed.
M&L for Applying two coats of oil bound distemper on new plastered surfaces of walls including preparation of surface and priming with chalk whiting, on plastered surfaces, preparatory to distempering complete all as specified and directed.
M&L for preparation of old decorated surfaces of walls by washing, rubbing down and stopping of distempered surfaces and applying one coat of oil bound distemper of approved shade/tint etc complete all as specified and directed.
M&L for preparation of new plastered surfaces and applying two coats of cement base paint of approved shade on walls including priming plastered and other surfaces with alkali resistant priming paint all as specified & directed by Engineer-in-Charge
M&L for complete removal of existing treatement on old plastered surface of wall & applying two coats of cement base paint over a coat of primer complete all as specified and as directed.
M&L for preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer etc complete all as specified and directed.
M&L for preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint etc complete all as specified and directed.
M&L for preparation of new steel surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer etc complete all as specified and directed.
M&L for preparation of old steel surfaces exc 10cm width or girth and applying one coat of synthetic enamel paint etc complete all as specified and directed.
Taking up or down steel tubing and connections with all fittings for 15 mm bore GI tubing etc complete all as specified and directed.
Taking up or down steel tubing and connections with all fittings for 20 mm bore GI tubing etc complete all as specified and directed.
Refixing of old steel tubing and connections in new or old position with new fittings to floor, wall or ceiling as directed, for 15mm bore GI tubing etc complete all as specified and directed.
Refixing of old steel tubing and connections in new or old position with new fittings to floor, wall or ceiling as directed, for 20mm bore GI tubing etc complete all as specified and directed.
S&F tubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc, 15 mm bore etc complete all as specified and directed.
S&F tubes medium grade, galvanised wih all fittings and fixed complete to walls and ceiling or laid on floors etc, 20 mm bore etc complete all as specified and directed.
S&F in repairs for 15mm dia bib taps cast copper alloy, fancy type, chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed etc complete all as specified and directed.
S&F Sinks without drainage board made of stainless steel 1mm thick with plugs and wastes including in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160m including waste pipe & coupling 32mm in repair etc complete all as specified and directed.
S&F in repairs for 15mm dia stop valves,fancy type and chromium plated screwed down high pressure screwed both ends for iron pipes or for Unions and fixed etc complete all as specified and directed.
S&F in repairs PVC connection 15mm dia and 45cm long with two Nos of brass checknuts and washers etc complete all as specified and directed.
S&F grating doom 125mm dia with waste hole of PTMT (Min wt 40 gms) etc complete all as specified and directed.
S& F in repairs PVC mounted 5mm thick bevelled edge looking mirror 600 x 450mm including taking down old fixed with chromium plated brass screws and cup washers etc complete all as specified and directed.
S&F 10 ltrs capacity PVC valveless syphonic action type flushing cistern low level with inlet ball valve float and dual fluash type complete all as specified complete all as specified and directed.
S&F vitreous china wash basin, size 550 x 400mm white including brackets, and waste coupling & pipe of 32mm dia, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other and fixed etc complete all as specified and directed.
S&F Toilet paper holder, coloured vitreous china, box type fixed to walls etc complete all as specified and directed.
S&F soap dish, vitreous china white, aprox size 160 X 160 X 90 mm etc complete all as specified and directed.
S&F Glass shelves, with 12mm thick desher glass incl CP brackets with brass nuts 300 mm long etc complete all as specified and directed.
S&F CP towel rail 600mm long with brackets, aluminium anodised 20mm dia etc complete all as specified and directed.
S&F CP grating 100mm dia PTMT with waste hole (Min wt 25 Gms) etc complete all as specified and directed.
S&F 15mm bore Pillar taps, cast copper alloy, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed etc complete all as specified and directed.
S&F PVC (SWR) Floor Trap plain with grating including jointing with solvent cement etc complete all as specified and directed.
S&F for vitrious china urinal, half stall type, white including flushing cistern, flush pipe and waste pipe. CP waste coupling etc complete all as specified and directed.
S&F rotational moulded polyethylene 250 Ltrs Capacity water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including ball brass valve, with polythelene float and fly nut complete screwed down for iron pipe of 20 mm dia etc complete all as specified and directed.
S&F 20mm gun metal, globe or Gate valves with iron wheel head screwed both ends for iron pipe and fixed etc complete all as specified and directed.
S&F for 15mm Bore Fancy Angel Stop cock, cast copper alloy, screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed etc complete all as specified and directed.
M & L for precast cement concrete (1:2:4) type B-1 using 20 mm stone aggregate as in manhole cover slabs round square or rectangular in shape including formwork and set in CM (1:4) etc complete all as specified and directed.
M&L for cement concrete type C2 (1:3:6) (using 40 mm graded stone agg) as in surface channels and drains etc complete all as specified and directed.
M&L for PCC (1:3:6) type C-1 using 20mm graded stone aggregate as in coping including necessary formwork complete all as spfd and directed
S & F 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.
S&F in repairs for Draperly rod /Harrison rails of CP of 20mm dia with fixing brackets , stops, rollers and rings etc complete all as specified and directed.
M&L for second class hardwood plain fillets exc 13sqcm and not exc. 25sqcm, square or rectangular in section, wrought, secured with nails or brads etc complete all as specified and directed.
S&F PVC (SWR) 110mm dia single socketed in any length with rubber ring joints laid in trenches or in floor etc complete all as specified and directed.
S&F PVC (SWR) 110mm dia bends in any radius etc complete all as specified and directed.
S&F PVC (SWR) 110mm dia junction single T equal or un equal with an floor etc complete all as specified and directed.
S&F of PVC (SWR) 75 mm dia vent cowl pipe as per specification etc complete all as specified and directed.
M & L for 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.
S & F 75mm bore PVC (SWR) bends any radius complete all as specified and directed.
S & F 110mm bore PVC (SWR) branch piece, single (single Y) equal or unequal etc complete all as specified and directed.
M&L Anti-termite treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron etc complete all as specified and directed.
S&F for 4 mm thick veneered decorative Plywood, grade-I (with BWR resin) with decorative face veneers on one face, fixed with screws to timber frame work complete all as specified and directed.
M & L for 10 mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.
Surface dressing n exc. 15 cm deep and getting out in soft/loose soil etc complete all as specified and directed.
M&L for Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out etc complete all as specified and directed.
Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, man holes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out of Soft/Loose soil etc complete all as specified and directed.
M&L for cement concret in foundation (1:4:8) Type D-2 using 40mm graded stone Aggregate etc complete all as specified and directed.
M&L for RCC (1:1.5:3) type A-1 (using20mm Graded stone Aggregate) nominal mix as in Foundations, including rafts,footings,plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete etc complete all as specified and directed.
M&L for RCC (1:1.5:3) type A-1 (using 20mm Graded stone Aggregate) as in column etc complete all as specified and directed.
Formwork to sides of concrete foundations, footings, bases of columns of foundation and plinth beams; and similar work for fair finished Surface etc complete all as specified and directed.
Formwork to sides of pillars, posts, struts, piers, columns and stanchions. for fair finished Surface etc complete all as specified and directed.
Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm etc complete all as specified and directed.
Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point etc complete all as specified and directed.
M&L for 40mm thick Damp proof course to horizontal or vertical surfaces including necessary formwork including applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre etc complete all as specified and directed.
M&L for Sand filling under floors or in foundations including watering and consolidation etc complete all as specified and directed.
M&L for Hardcore (stone aggregate) of gauge n exc. 63 mm, deposited, spread and levelled in layers nexc. 15 cm thick, watered and rammed to a true surface etc complete all as specified and directed.
M&L for 25 mm thick Cement Concrete for Finishig Course Type B-1 (1:2:4) (using 20mm graded stone aggregate) etc complete all as specified and directed.
M&L for Brick work with sub class B bricks using old size straight or curved on plan exc 6mm mean radius built in Cement Mortar 1:4 etc complete all as specified and directed.
Form work with fair finished surface to Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc complete all as specified and directed.
S&F Factory made solid panel PVC door shutter30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification etc complete all as specified and directed.
S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification etc complete all as specified and directed.
S&F for 15 mm bore Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed etc complete all as specified and directed.
S&F for steel ventilator with top hung shutter including hinges steel peg stay, complete all as specified and directed.
M/L sheet glass, obscured or Frosted 3mm thick and glazing with oil putty in squares. nexc 0.5 Sqm each etc complete all as specified and directed.
M&L for 2nd class hard wood Not exc 3sqcmPlain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads etc complete all as specified and directed.
M&L for 80mm thick machine pressed precast concrete interlocking paver block coloured with grey cement and no pigment of any shape and size confirming to IS 15658-2006 of 80mm thickness M-40 grade set jointed and pointed with grey cement incl 25mm thick sand cushioning complete all as specified.
M&L for forming contraction (Dummy) joints 65mm deepx10mm wide, filled with sealing commound etc complete all as specified and directed.
M&L for Plain cement concrete (1:2:4) type B-1( using 20mm graded crushed stone aggregate ) as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified.
Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete, including fitting & fixtures such as switches with board, ceiling roses, pendents, bell/ buzzer, bell push, lamp holders, regulators, sockets, light fittings etc., removing material from site and making good to the disturbed surfaces of walls, ceiling, floors etc. including making good the disturbed surfaces and paint touch up to match with the existing surface complete all as specified and as directed.
Taking down carefully by unscrewing from fittings any type such as ceiling fittings, bulk head fittings, tube light fittings etc. for reuse at site or carrying to the store (To be measured only when found serviceable in all respects complete for reuse).
M&L for Point wiring complete with two runs of 1.5 sqmm single core PVC insulated FR-LSH cable 1100 volts grade with multi-stranded copper conductors, drawn through and including PVC double locked Casing & caping including provision of 1.5 sqmm, FR-LSH, PVC insulated copper cable as earth continuity conductor connected to common earth dolly, including PVC rectagular box for mounting switches / sockets / regulators etc. with 3 mm thick plastic laminated sheet cover of suitable size as required at site complete all as specified and as directed.
(a) One light/Exhaust/Call Bell /Fan pointcontrolled by one, one way switch .
(b) One 3 pin socket outlet 5 Amps on the same board with other switches.
(c) One 3 pin socket outlet 5 Amps on the switch socket combination.
All as per item No 146.00 here-in-before but with 2.5 Sq mm for 3 pin 15 Amps socket point controlled by one switch on independent board and 2.5 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly complete all as specified and as directed.
All as per item No 146.00 here-in-before but with 4.0 Sq mm for 3 pin AC point controlled by one switch on independent board and 4.0 Sq mm copper conductor green in colour as earth continuity conductor connected to common earth dolly etc complete all as specified and as directed.
M&L for Switch piano flush type single pole, one way 5A etc complete all as specified and as directed.
M&L for Socket outlet, 2 in 1, 5 pin 5A flush type etc complete all as specified and as directed.
M&L for Switch Socket combination, 2 in 1, 5 pin 6A flush type etc complete all as specified and as directed.
M&L for Switch Socket combination, 2 in 1, 5 pin 6A/16A flush type etc complete all as specified and as directed.
M&L for stepped type electronic fan regulator 100 Watt socket size flush type on the existing phenolic laminated sheet etc complete all as specified and as directed.
M&L for ceiling rose 3 terminal PVC/Polycarbonate isolated body with PVC round/squareblock complete all as specified and directed.
M&L for Modular Switch 1 way 6A,1 module etc complete all as specified and as directed.
M&L for modular switch 1 way 16A, 1 module etc complete all as specified and as directed.
M&L for Modular Socket ,6A/2/3 pin combined 2 module etc complete all as specified and as directed.
M&L Modular Socket ,6A/16A-2/3 pin combined 2 module etc complete all as specified and as directed.
M&L for Modular Bell push 6A 1 module etc complete all as specified and as directed.
M&L for Bell Multi Music type etc complete all as specified and as directed.
M&L for stepped type electronic fan regulator,120 W-2 module etc complete all as specified and as directed.
S & F Modular white cover plate with frame 2 module and metal flush box 2 module etc complete all as specified and as directed.
S & F Modular white cover plate with frame 3 module and metal flush box 3 module etc complete all as specified and as directed.
S & F Modular white cover plate with frame 4 module and metal flush box 4 module etc complete all as specified and as directed.
S & F Modular white cover plate with frame 6 module and metal flush box 6 module etc complete all as specified and as directed.
S & F Modular white cover plate with frame 8 module and metal flush box 8 module etc complete all as specified and as directed.
Taking down existing burnt aluminium/ copper sub main wiring and M&L for sub main wiring with two runs of 4 Sq mm and one run of 4 Sq mm for earth wire with multi standard copper conductors, 1100 volts grade, drawn through and including PVC double locked Casing & caping including complete all as specified and as directed. NOTE:- two runs of 4 Sq mm + one run of 4 Sq mm and one run of PVC casing & capping and its accessories of suitable size shall be measured as one unit length .Make:- Finolex/Havells/RR Kabel Make of caping/casing :- Prestoplast/Finolex/supreme
Taking down S&F for LED Light fitting 1 x 22 watt (4 Ft), Wall/ Surface mounted, intergrated type with pvc block 02 Nos and all accessories internally prewired and incl connecting up with and incl twin/ three core twisted flexible copper conductor cable of suitable size in and incl flexible hose from ceiling rose to fitting complete all as specified and as directed. Make : Crompton Geaves Cat No -CCS-102-20-65-SL-DP-NWH/ Bajaj/ Philips.
All as per item No 168.00 above but 10 watt LED, 2' batten etc complete all as specified and as directed. Make : CG/Bajaj/Philipsake : Anchor/Legrand/Kinjal
M&L in replacement for Decorative wall mounted light fitting made up of polycarbonate including 9 watt LED lamp (Red/Green) with B-22 base including taking down old unsv light fitting complete all as specified and as directed. Make: Havells/Bajaj/Surya
Taking down Supply , fixing and testing in replacement of LED Bldg Security light fitting of capacity 25 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete including 1.2 mtr GI bracket of 25mm bore light grade bent to shape and fixed on wall with metal fastners 2 Nos 10mm dia incl drilling of holes as reqd and connecting up with flexible copper cable of size 0.75 sqmm 3 core from ceiling rose to the light fitting and all as specified and directed by Engr-in-Charge..Make : CG, Cat No- LSTS-20-CDL-M/ Bajaj/ Philips
Supply and fixing LED luminaire 600 mm x 600 mm, 40/42 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.
Supply and fixing Supply and fixing round shape 6 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size etc complete all as specified and as directed.
M&L for Distribution board double door type (for incoming MCCB 100 Amps 4 Pole & out going MCBs) DPX 4 way, sheet steel, powder painted, with bus bar neutral link & earth bar etc. and fixing only incoming MCCB and MCBs of various rating capacity including taking down old unsv DB of any capacity etc complete all as specified and as directed. rt No 507611/ABB/Siemens
Supply and fixing MCCB 3 Pole .415 Volts fixed type, 125 Amps with breaking capacity 16 KA complete with connection testing and commissioning etc complete all as specified and as directed.
Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300 mm complete all as specified and as directed. Make : Bajaj/CG/Orient
Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate NRV, connection piece etc complete all as specified and as directed.
S & F distribution board iron clad, double door with IP-43 1K-09 protection suitable for MCCB as incommer and MCB as outgoing 415 Volts 3 phase 50 C/s 4 way, complete with appropriate size copper bus bar and neutral link confirming to cat pt No 5077 45 of Legrand or equivalent of make ABB/Siemens complete with one MCCB 3 pole 415 Volts 100 Amps rating with rupturing cap 16 KA and 12 Nos of MCB SP as required of the same make as of distribution board & including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site or directed by Engr-in-Charge (Outgoing MCB will be measured separately).Make : Legrand Cat Part No 507611/ABB/Siemens
M&L for MCB Distribution board double door type SPN 8 way, sheet steel, powder painted, with neutral link & earth bar etc. and fixing MCBs of various rating capacity including taking down old unsv MCB DBs complete all as specified and as directed.
Supply and fixing MCB SPN 40-63 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed. Make : Legrand Cat Part No 408618/ABB/Siemens
M&L for MCB SPN 40 Amps 'C' series, 230 volts, 50 Hz suitable for fixing in MCB DB incl taking down old unsv MCB complete all as specified and as directed
M&L for MCB SP 6-32 Amps 'C' series, 230 volts, 50 Hz suitable for fixing in MCB DB incl taking down old unsv MCB complete all as specified and as directed.
M&L for MCB SP 40-63 Amps 'C' series, 230 volts, 50 Hz suitable for fixing in MCB DB incl taking down old unsv MCB complete all as specified and as directed.
M&L for metal clad AC socket point single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB SP 20 Amps complete all as specified and as directed. Make: Havells/HPL/Legrand
Taking down Ceiling fan/ Exhaust Fan of any sweep carefully from its installed position, dismantling complete, cleaning all dust, applying grease for bearing, including filling cavaties with filler, after cleaning all dust, reassembling the fan and blades, hanging/ fixing the fan in its original position and testing on completion complete all as specified and as directed.
M&L for rubber bush with clamping set, comprising GI bolt, nut and split pin complete all as specified and as directed.
M&L for replacement of capacitor2.5 Mfd incl making electrical connection complete all as specified and as directed.
M&L for replacement of steel ball bearing/bush of suitable size compatible to the existing ceiling fan complete all as specified and as directed.
M&L for copper rewinding for suitable size complete to the existing ceiling fan/Exhaust Fan complete all as specifed and as directed.
Taking down LT UG cable/ service connection of any size and M&L for laying of LT UG cable, XLPE insulated, galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area of 25 sq mm, 3.5 core complete all as specified and as directed. NOTE :- (i) Excavation and earth work, sand cushioning, cable protection cover, pipe etc. shall be measured and paid seperately under relevant items.
M&L for spread fine river sand in trenches etc complete all as specified and as directed. NOTE: For measurement purpose, punned down thickness shall only be taken.
M&L for laying brick sub class 'B' old size burnt bricks for cable protection of size 230mmx115mmx75mm complete all as specified and as directed
Supply & laying tubes 'light grade' galvanised, with all fittings, fixed complete to walls, poles, ceilings or laid in floors/ trenches/ road crossing for protection of cables of size 40 mm dia bore including taking out unsv GI tubing complete all as specified and as directed.
Materials and labour for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised strip 32x6mm by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe of 40mm bore (light grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including testing on including taking down old u/s materials completion all as specified and as directed.
Material & Labour for earthing with galvanised steel earth plate electrode of size 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to the galvanised earth lead wire 4 mm by means of bolts, nuts check nuts and washers of galvanised iron or steel as shown in electrical plate No. 3 of SSR Part-I connected to earthing test point all as specified orindicated including testing on completion including necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in PCC 1:3:6 type C-1, RCC (1:1.5:3) type A1 precast cover (54cmx54cmx5cm) duly reinforced with including 8 mm dia TMT bar @ 150mm c/c both ways, one lifting handle made of 8mm dia TMT bar, embeded in precast cover slab, funnel, 20mm dia GI medium grade watering pipe, 15mm dia GI light grade earth lead protection pipe, chorcoal and common salt in alternatee layer complete all as specified and directed by Engr-in-Charge.
M/s MATRI ENTERPRISES
M/S ARVIND GROUP OF CONSTRUCTION & INFRASTRUCTURE
commercial enterprises
SK SINGH
sanjay kumar
M/S SANGITA TRADERS
VIHUTO YEPTHO
MS SADHNA RAHUL
stage.html
html • 0.07 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .