Guest House cum Yatriniwas at Amingaon

Amount

CIVIL WORKS EARTH WORK IN EXCAVATION Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in- charge. All kinds of soil.

Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete. (Measurements to be taken of the face area timbered). Depth exceeding 3 m but not exceeding 4.5 m

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

PLINTH FILLING Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

ANTI-TEMetreITE TREATMENT Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- teMetreite treatment (excluding the cost of chemical emulsion) : Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- teMetreite treatment (excluding the cost of chemical emulsion) : With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- teMetreite treatment (excluding the cost of chemical emulsion) : Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- teMetreite treatment (excluding the cost of chemical emulsion) : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- teMetreite treatment (excluding the cost of chemical emulsion) : Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing soling in foundation and under floor with stone/best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a) Brick on flat soling

SURFACE DRESSING AND JUNGLE CLEARING Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.

Embankment Construction with Material Obtained from Borrow Pits Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requiMetreent of table 300-2 (Including cost of testing of materials at site and laboratory as directed by the deptt.) (i) from private land

Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requiMetreent of table 300-2 (Including cost of testing of materials at site and laboratory as directed by the deptt.) Extra lead beyond initial lead of 3.0 Km.

Removing , derooting & disposing of water hyacinth , water bond vegetation trees etc and desposing the same outside of the proposed site premise.

CONCRETE WORKS: 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

DAMP-PROOF COURSE Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)

PLINTH PROTECTION Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation leveling and dressing and finishing the top smooth.

PLINTH PROTECTION DRAIN Providing drain with cement concrete (1:3:6) 10cm thick sides 10cm thick bed over brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified. i) 300mm wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm.

Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge. a) 100 mm thick slab

REINFORCED CEMENT CONCRETE WORKS Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level : Concrete of sqm5 grade with minimum cement content of 300 kg /cum

Concrete of M30 grade with minimum cement content of 350 kg /cum

All works above plinth level upto floor V level Concrete of sqm5 grade with minimum cement content of 300 kg/cum

Concrete of M30 grade with minimum cement content of 350 kg /cum

FOMetreWORK Centering and shuttering including strutting, propping etc. and removal of foMetre for : Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platfoMetre

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs (excluding landings) except spiral-staircases

Edges of slabs and breaks in floors and walls Under 20 cm wide

Weather shade, Chajjas, corbels etc., including edges

STEEL REINFORCEMENT Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. TheMetreo-Mechanically Treated bars of grade Fe-500D or more.

Mild steel and Medium Tensile steel bars

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

MASONRY WORK Brick work with common burnt clay F.P.S. (non-modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : Cement mortar 1:3 (1 cement :3 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement :3 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement : 4 coarse sand)

Autoclaved Aerated concrete (AAC) Block Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

RANDOM RUBBLE MASONRY Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)

MS GRILL Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

ALUMINIUM FITTINGS Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 300mm X 16mm.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete: 300x10 mm

Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 125 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper

STEEL WORK ( gate) Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

MDF BOARD Providing and fixing Pre -laminated medium density fibre board exterior grade (Grade-I) IS:14587:1998 marked, to frame, backing or studding with screws etc. complete ( Frames, backing or studding to be paid separately). Pre-laminated with decorative lamination on both side exterior Grade - I MDF Board 12 mm thick confiMetreing to IS:14587

Providing and fixing to existing door frames. 35 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate confoMetreing to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge.

Providing and fixing SS mate finished 240 mm Lock Body Chrome mortice lock with 6 levers including a pair of SS mat finished handles of approved quality for Wooden and FRP door, with necessary screws etc from reputed brand like Godrej, Hettic, Hafele or equivelent. Complete as per direction of Engineer- in-charge.

Supplying and fixing 200mm door handle set with lock body 2C SS SS made finish handles of approved quality for wooden and FRP door, with necessary screws etc. from reputed brand like Godrez, Hettic, Hafele or equivalnent complete as per direction of Engineer-in-Charge.

Providing and fixing bright finished brass double acting spring hinges with necessary brass screws etc. complete 100 mm

UPVC WINDOW Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll foMetreing process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size

and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Two track two panels sliding window made of (small series) frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm)

Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm).

Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll foMetreing process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all

complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll foMetreing process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing

hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes,wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 2.50 sqm upto 4.00 sqm.)

Providing and fixing factory made uPVC white colour sliding glazed door comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll foMetreing process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel

screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Two track two panels sliding door made of (big series) frame 67 x 50 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm)

Providing and fixing steel roller for uPVC sliding door with necessary screws etc. complete.

Providing and fixing steel (white power coated) crescent lock for uPVC liding window/ door with necessary screws etc. complete.

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 37mm x 15mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat.Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiberglass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

STAINLESS STEEL RAILING Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.

FLOORING Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.

TILES WORKS Providing and fixing Ist quality ceramic glazed wall tiles confoMetreing to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 1st quality ceramic glazed floor tiles confoMetreing to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

VITRIFIED FLOOR TILES Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and confoMetreing to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) confoMetreing to IS: 15477, in average 3mm thickness.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and confoMetreing to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Antiskid finish of size Size of Tile 600 x 600 mm

Providing and laying full body Vitrified Tiles Applico series of size 800mm x 2600mm with thickness 15mm, (IS15622: 2017 group BI a) approved make in colour such as terastone Ivory laid on cement morter 1: 3 ( 1 Cement : 3 Coarse sand Jointing with grey cement slurry @ 3.3 kg/sqm including pointing joints with white cement and matching pigment etc., complete. designed for outdoor environment and heavy vehicle parking.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling/ grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 1000x1000 mm and above

MARBLE FLOORING Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

GRANITE FLOORING Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platfoMetres, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab colour black, Cherry/Ruby red Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete. 8mm thick Granite of any colour and shade

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

ROOFING TILES Providing and laying pressed clay tiles (as per approved pattern 20 mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound, laid over a bed of 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete.

RAIN WATER PIPE Providing and fixing on wall face unplasticised Rigid PVC rain water pipes confoMetreing to IS : 13592 Type A, including jointing with seal ring confoMetreing to IS : 5382, leaving 10 mm gap for theMetreal expansion, (i) Single socketed pipes. 100 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes confoMetreing to IS : 13592 Type A, including jointing with seal ring confoMetreing to IS : 5382, leaving 10 mm gap for theMetreal expansion.Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes confoMetreing to IS : 13592 Type A, including jointing with seal ring confoMetreing to IS : 5382, leaving 10 mm gap for theMetreal expansion. 75 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes confoMetreing to IS : 13592 Type A, including jointing with seal ring confoMetreing to IS : 5382, leaving 10 mm gap for theMetreal expansion. 75 mm bend

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Filling sunken floor with broken jhama brick bats and sand including compacting and supplying of materials complete as specified and directed for all levels.

CEMENT PLASTERING 12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

CEMENT PLASTER WITH A FLOATING COAT OF NEAT CEMENT 12 mm cement plaster finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand)

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

PAINTING WORKS EXTERNAL PAINTING Finishing old / new wall with water proofing weather coat smooth anti-fungal exterior painting of approved make of paint of required shade after cleaning and clearing the surface etc. including scaffolding complete as directed at all levels (two coats)Berger paint / Asian Paint / Dulax (ICI) paint/ Nerolac Paint / Snowcem India Ltd.

Finishing walls with water proofing cement paint of required shade: New work (Two or more coats applied @ 3.84 kg/10 sqm)

PAINTING ON STEEL AND OTHER METAL SURFACE Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

INTERNAL PAINTING (PLASTIC PAINT) Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality L D- 2.5 Rectangular shape 600x450 mm internal dimensions

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 19.32.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: Inside dimensions 455x610 mm and 45 cm deep for single pipe line : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

PILE WORKS Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tubewell boring machine shall not be used. 450 mm dia piles

PILE WORKS Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tubewell boring machine shall not be used. 600 mm dia piles

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platfoMetre by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing. Note: 2. Testing agency shall submit the design of loading platfoMetre for the approval of Engineer-in-charge. Single pile upto 50 tonne Safe capacity Initial test (Test Load 2.5 times the Safe capacity)

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platfoMetre by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing. Note: 2. Testing agency shall submit the design of loading platfoMetre for the approval of Engineer-in-charge. Routine test (Test Load 1.5 times the Safe capacity

Lateral load testing of single pile in accordance with IS Code of practice IS : 2911 (Part IV) for deteMetreining safe allowable lateral load on pile : 20.8.1 Upto 50 tonne capacity pile

ALUMINIUM WORKS Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make confoMetreing to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board confoMetreing to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass/ stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

WATER PROOFING AND ROOF TREATMENT Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured. For the purpose of measurement the entire treated surface will be measured.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing peMetreeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product perfoMetreance shall carry guarantee for 10 years against any leakage. For vertical surface two coats @ 0.70 kg per sq

CEMENT BOARD CLADDING Providing and fixing of external wall system on Light gauge steel frame work with outer face cement boards as per standard sizes fixed with self- drilling / taping screws / fasteners @ 60cm c/c of approved make. A groove of 2 mm to 3mm shall be maintained and grooves shall be sealed with silicon based sealant. The board shall be fixed in a staggered pattern. Screws shall be of counter sunk rib head of 1.60mm to 4 mm thick or 8 to 10 gauge of length varying from 25 to 45 mm and. Internal face 12.5 mm thick gypsum plaster board fixed on cement board as per standard sizes fixed with selfdrilling / taping screws / fasteners @ 60cm c/c of approved make, proper taping and jointing to be done using fiber mesh tape and epoxy and acrylic based jointing compound for seamless finish.(cost of frame work to be paid for separately) Outer face: Outer face having 6mm thick fiber cement board fixed on 9mm thick fiber cement board, Type A, as per IS:14862:2000 (high pressure steam cured) Inner Face :- 12.5 mm thick gypsum plaster board confoMetreing to IS 2095:2011 fixed on 8 mm thick fibre cement board confiMetreing to IS:14862:2000 of type B (High pressure steam cured)

Supplying materials and laying of Modified Clay Material (MCM) as per company standard dimension, pattern, color as specified, manufactured through unfired, patented manufacturing technology, bonded together by using low heat temperature. The product should be compatible for interior use and certified by IGBC. MCM Materials should be fixed with suitable Cement/ Polymer/Epoxy based adhesive as per adhesive chart and substrate. Filling and pointing of grout should be as per installation guidelines and approved drawing. Prior approval should be obtained for finalization of the colour of material and grout. Including necessary makeup to made the surface even and smooth, scaffolding, framing etc. for installation at all level and corner. Finished and complete in all respect and as per the direction of Engineer in-charge. aApproved pattern - as per design thickness Approx 2.5 to 25mm (for internal application)

PEB STRUCTURE: Supplying, installation, testing and commissioning of PEB Structure as per the enclosed drawing and specifications in Annexure - I. All materials, design perameter and installation should be done according to the code of practice defind in the specification. Priror approval on detailed drawings, structural design, colour code etc. should be obtained from the authority before finalization of the proposal. The Structure should design and complete in accordine with relevant code and specification. Including PCGI roofing sheet , finished and complete in all respect and as per instruction of Engineer in Charge. AS PER ANNEXURE - I

Soft Ceiling and Cladding system Supplying and installation of water proof, non-VOC emission, seamless post installation, teMetreite and rust proof PVC ceiling of panel of size not less than 3060 x 300 mm fixed in a frame work of J and T profile of size not less than 3060 x 22 and 3060 x 42 accordingly. The profile framework should fix rigidly with the wall/ roof with necessary arrangements like screws, nails, drop bars etc. Prior approval should be obtained before finalization of the colour and texture of the panels. Necessary cutting/ provisions should be kept for fixing light fixtures (surface mounted or recessed type) without damaging the seamless look of the ceiling/ wall cladding. Including necessary side beading, joint filler etc. and complete in all respect as per the specification and instruction of Engineer in Charge.

Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer in -charge which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/msqm, modulus of elasticity 850 N/msqm and resistance to spread of flame of Class A category with properties of being teMetreite/borer proof, water/moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 25 x 1.5 mm square hollow box section including applying a priming coat of approved steel primer, placed at grid made at 1.0 x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all complete as per direction of Engineer-In- Charge. (Note: M.S (mild steel) framework with priming coat and necessary SS fasteners and SS screws shall be paid separately.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture confoMetreing to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainle

CURTAIN GLAZING Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the specified design loads confoMetreing to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. (d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. (e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge.

The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. PerfoMetreance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or any other accreditation body which operates in accordance with ISO/ IEC 17011 and accredits labs as per ISO/IEC 17025 1. PerfoMetreance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr 2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml. 3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml 4. Structural PerfoMetreance Deflection and defoMetreation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm 5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test, Tests to be conducted on site. 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete 1200 mm dia. R.C.C. pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :150 mm dia. R.C.C. pipe

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall ,50 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work:, 50 mm dia nominal bore metre 654.20

Tube Well Labour for test boring with 40mm (internal) dia G.I. Pipes including keeping surplus of earth and every 2.00m after first 3.00m depth and delivering the same in nearest P.W.D. camp in the small tin container (container, scaffolding, tools etc. will have to be arranged by the contractor at his own cost).

Machine boring of deep tube well upto 200 mm dia. Bore hole as directed by the Engineer in Charge

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, confoMetreing to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, confoMetreing to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (SUCTION PIPE) 50 mm nominal outer dia Pipes

Providing and placing in position filters of 40 mm diameter G.I./ PVC pipe with brass strainer of approved quality.

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 50 mm nominal outer dia Pipes Horizontal

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 50 mm nominal outer dia Pipes Vertical

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond peMetreissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 150 mm dia

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 150 mm dia.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 200 mm dia

Providing and stacking of Cassia fistula (Amaltash) of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and displaying of Croton baby golden variety having ht.30 cm and above, well developed with full of fresh and healthy leaves in 20 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing & fixing of White River (Stone) Pebbles size of 2" to 2.50" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge.

Providing and stacking of Polyalthia longifolia (Ashok) of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge.

Providing and displaying of Dracaena rosea having ht. 30 cm & above with 8 to10 leaves, well developed, fresh and healthy in 20 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Peltophorum species of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Bauhinia purpurea (Kachnar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge

Providing and stacking of Bombax ceiba of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Inga dulcis (Jungle Jalebi) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Jacaranda mimosifolia of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Chlorophytum-variegated, full of leafy suckers in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and displaying of Aglaonema Ice ht.25 cm having 10 to 12 fresh, healthy and attractive colorful leaves, well developed in 25 cm size Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Araucaria cookie having ht. 1.80 m to 1.95 m, straight, well developed, fresh and healthy with lush green leaves from bottom to top in 30 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and stacking of Daniella variegated, with 3 to 4 variegated leaves in 20 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge..

Providing and displaying of Chamaedorea elegans palm having ht. 60 cm to 75 cm, well developed with fresh and healthy leaves in 25 cm size of Earthen pot/Plastic pot. & as per direction of the officer-in-charge.

Providing and Displaying Chrysanthemum double variety, well developed, having 45 to 60 cm ht., with 6 and above flowers with half blooming condition, fresh and healthy with bamboo stacking in 25 cm Earthen Pot and as per direction of the officer-in-charge.

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (DhuMetreos) and than rolling the surface with light roller make

Providing and stacking of Thuja compacta of height 75-90 cm., conical shaped, well foMetreed with healthy foliage in earthen pots of size 30 cm as per direction of the officer-in-charge.

Providing and Displaying Marigold jaffri orange/yellow/Russet colour well developed with fresh & healthy foliage with 40 to 50 flowers in bloom specimen plant 60 to 75 cm ht in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Supplying and installation of free hold hanging dust bin made out of FRP di moulded min 4mm thick body thickness with necessary tilting arrangement design for easy cleaning from reputed brand like supreme, sintex or equivalent. The dust bin will be placed in pair of red and green colour but with provision of individual-tilting provision. the bidder should obtain prior approval of design of the dustbin before installation from the authority. The rate is inclusive of required civil works for fixing the same in position.

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be reduced by 8% for payment).

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : 2.4.1 Screened through sieve of I.S. designation 20 mm

Rough dressing the trenched ground including breaking clods.

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately Holes 90 cm dia, and 90 cm deep

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately Holes 60 cm dia, and 60 cm deep

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately Holes 45 cm dia, and 45 cm deep.

Turfing with Sods (Furnishing and laying of the sqm 31.00 live sods of perennial turf foMetreing grass on embankment slope, verges or other locations shown on the drawing or as directed by the engineer including preparation of ground, fetching of rods and watering)

IRREGATION:Supply, install, test and commission an mannual irrigation system with, pop-up sprinkler system, HDPE or UPVC pipes, pump and tank complete to provide a unifoMetre coverage with an application rate of up to 7mm/day to the plants and to provide a full set of spare parts, staff training and support. Supplying all the required materials like pipes (of all kind and diameter) calves, pop-up sprinkler etc. for watering the vegetation/plants etc. The Sprinklers should be automatic Pop-Up Sprinklers, full/part circle to be placed suitably to avoid unnecessary water dropping to other structures with required discharge length according to the layout of the park.The system should include total installation with stainless steel nozzle and drive assembly, water lubricated heavy duty gear drive. The products are to be from reputed manufacturer/ make like Toro, Railbird , Sime, Hunter etc. All risers shall be installed in such a manner that they can be adjusted to level with a height range. Valve box with cover on all valves shall be reinforced heavy duty plastic with a green colour finish, and placed suitably for easy operation and maintainence. A filtration system; providing & fixing of disc filter (120 mesh) capacity30m3 /hr having an inlet & two outlets connections of 2", 2 pressure gauge ports of 3/4", a helix made of fibre glass reinforce polyamide at base of disc filter cartridge to create a helical effect in the incoming water from the nearby pond. Necessary arrangements to collect water from the natural water body shall be taken in consideration. Fixing of outlet for flushing at bottom of filter of required dia shall be fixed. The succesfull bidder shall submit a layout plan for due approval of the authority before implementation. The item icludes design, execution, training of operating staff and AMC for atleast one year.

Oudoor Children playing equipment.: SINGLE SEATER SPRING RIDER Supplying, installation, testing & commissioning of multi activity play system of reputed brand or manufacturer made out of GI/ MS :- Class B and confoMetreing to IS-1239. LLDPE Plastic :-UV Stabilized. HT SPRING : Jerk resistance, heigh strength, Flexible. FRP SLIDE, SEAT & STRIP : Fiber Rainforce Plastic is layer of pigment, resin & hardner material, thikness 4 to 8 mm, die moulded process, glossy finish surface Acrylic :- Acrylic clarity, light weight, impact resistance, and weather resistance. Aluminium Clamp :- high fatigue strength, excellent castability, very good corrosion resistance,self-piercing riveting and clinching. PP Caps :- caps are manufactured from high quality polymers. GI Hardware :- All galvanizing hardware are carried out by the hot dip process, in accordance with specification IS 2629. Vinyle Sticker :- High Strength Acrylic Adhesive 300 is designed to be compatible with a variety of print methods and end use applications. MIG welding :- it is versatile and can be used with a variety of metals and alloys, corrosion resistance, soft surface to prevent injuries. Powder Coating :-The finish is more flexible than traditional paint, and allows for a small amountof bending and flexible as parts vibrate and move. Rubber belt :- Rubberized coating oover the steel core, height strength, flexible

Oudoor Children playing equipment.:2 SEATER ARC SWING Supplying, installation, testing & commissioning of multi activity play system of reputed brand or manufacturer made out of GI/ MS :- Class B and confoMetreing to IS-1239. LLDPE Plastic :-UV Stabilized. HT SPRING : Jerk resistance, heigh strength, Flexible. FRP SLIDE, SEAT & STRIP : Fiber Rainforce Plastic is layer of pigment, resin & hardner material, thikness 4 to 8 mm, die moulded process, glossy finish surface Acrylic :- Acrylic clarity, light weight, impact resistance, and weather resistance. Aluminium Clamp :- high fatigue strength, excellent castability, very good corrosion resistance,self-piercing riveting and clinching. PP Caps :- caps are manufactured from high quality polymers. GI Hardware :- All galvanizing hardware are carried out by the hot dip process, in accordance with specification IS 2629. Vinyle Sticker :- High Strength Acrylic Adhesive 300 is designed to be compatible with a variety of print methods and end use applications. MIG welding :- it is versatile and can be used with a variety of metals and alloys, corrosion resistance, soft surface to prevent injuries. Powder Coating :-The finish is more flexible than traditional paint, and allows for a small amountof bending and flexible as parts vibrate and move. Rubber belt :- Rubberized coating oover the steel core, height strength, flexible

Oudoor Children playing equipment.: ADVENTURE CLIMBER Supplying, installation, testing & commissioning of multi activity play system of reputed brand or manufacturer made out of GI/ MS :- Class B and confoMetreing to IS-1239. LLDPE Plastic :-UV Stabilized. Acrylic :- Acrylic clarity, light weight, impact resistance, and weather resistance. Aluminium Clamp :- high fatigue strength, excellent castability, very good corrosion resistance,self-piercing riveting and clinching. PP Caps :- caps are manufactured from high quality polymers. GI Hardware :- All galvanizing hardware are carried out by the hot dip process, in accordance with specification IS 2629. Vinyle Sticker :- High Strength Acrylic Adhesive 300 is designed to be compatible with a variety of print methods and end use applications. MIG welding :- it is versatile and can be used with a variety of metals and alloys, corrosion resistance, soft surface to prevent injuries. Powder Coating :-The finish is more flexible than traditional paint, and allows for a small amountof bending and flexible as parts vibrate and move. Rubber belt :- Rubberized coating oover the steel core, height strength, flexible.

Oudoor Children playing equipment.: 2 SEATER SPRING SEE-SAW Supplying, installation, testing & commissioning of multi activity play system of reputed brand or manufacturer made out of GI/ MS :- Class B and confoMetreing to IS-1239. LLDPE Plastic :-UV Stabilized. HT SPRING : Jerk resistance, heigh strength, Flexible. FRP SLIDE, SEAT & STRIP : Fiber Rainforce Plastic is layer of pigment, resin & hardner material, thikness 4 to 8 mm, die moulded process, glossy finish surface Acrylic :- Acrylic clarity, light weight, impact resistance, and weather resistance. Aluminium Clamp :- high fatigue strength, excellent castability, very good corrosion resistance,self-piercing riveting and clinching. PP Caps :- caps are manufactured from high quality polymers. GI Hardware :- All galvanizing hardware are carried out by the hot dip process, in accordance with specification IS 2629. Vinyle Sticker :- High Strength Acrylic Adhesive 300 is designed to be compatible with a variety of print methods and end use applications. MIG welding :- it is versatile and can be used with a variety of metals and alloys, corrosion resistance, soft surface to prevent injuries. Powder Coating :-The finish is more flexible than traditional paint, and allows for a small amountof bending and flexible as parts vibrate and move. Rubber belt :- Rubberized coating oover the steel core, height strength, flexible.

Design, SITC of Water Treatment Plant including excavation, back filling & disposal of surplus earth MS/civil contruction) on line iron removal filter plant . The iron removal Filter plant would comprised MS Oxidation chamber,Ms multigrade filter Chamber for flow capacity of approx 30cum/hr & also chlorine dosing system, air compressor, pump, valves, fittings and all accessories complete.The iron content of filter output water must confiMetre to IS standard peMetreissible limitsfor the following duty: (AS PER ANNEXURE - VII)

EWC Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

EWC: Providing fitting and fixing Vitreous china wall hang water closet (European type W.C pan 400mm high) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately) a) White (ii) Wall mounted Closet (inclusive of seat cover and fittings) Jacquar Model no. DRS-WHT-37951 Hindware Model no. 92097 (P-21) Kohler Model no. K-17647IN-S-0

CONCEALED CISTERN Supplying, fitting and fixing concealed cistern with all internal fittings with CI brackets including supplying, fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified . Concealed Cistern with Control Plate (CP) from approved manufacturer. Hindware Model no. 518237 (Concealed Cistern), Hindware Concealo Neo (Aura) (Flush Plate) Roca Model no. RE890010100 (Concealed Cistern) , Roca Model no. RE890195000 (Flush plate) Kohler Model no. K-77029IN-M-NA(Concealed Cistern), Kohler Model no. K-4177IN-M-CP (Flush plate)

WASH BASIN Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately) BASIN (with pedestal) Jacquar Model no. CNS-WHT-801 AND 301 Roca Model no. RS337461_ _0 Hindware Model no. 10012

KITCHEN SINK Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm

WALL MIXTURE Providing and fixing CP Brass Single lever wall mixer of quality & make as approved by Engineer in charge. 15 mm nominal dia

WASTE PIPE Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste pipe fittings complete. Semi rigid pipe 40 mm dia

MIRROR Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm

GLASS SHELF Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

TOILET PAPER HOLDER Providing and fixing toilet paper holder : C.P. brass

URINALS Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

BIB COCK Providing and fixing C.P. brass long body bib cock of approved quality confoMetreing to IS standards and weighing not less than 690 gms. 15 mm nominal bore

STOP COCK 15 MM Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make confoMetreing to IS:8931 : 15 mm nominal bore

STOP COCK 20MM Providing and fixing brass stop cock of approved quality : 20 mm nominal bore

ANGLE VALVE Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality confoMetreing to IS:8931: 15mm nominal bore

BOTTLE TRAP Providing and fixing CP Brass 32 to 40 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

SHOWER ROSE Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 150 mm diameter

TELEPHONIC SHOWER :Supplying fitting and fixing Telephonic Chrome Plated (C.P.) shower of approved brand as directed and specified. (Pipes will be measured and paid separately) Jaquar make: a) Continental (i) Telephone shower 2-in-1 shower with massage effect with 1.5m SS tube and swinging wall hook

FLOOR TRAP Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent aMetre complete, including cost of cutting and making good the walls and floors 100 mm inlet and 75 mm outlet: Silver with crome finish solid construction fast drainage and automatic sealing

WASTE COUPLING FOR BASIN Providing and fixing CP Waste Coupling for wash basin of approved quality 31 mm dia of 79 mm length and 62mm breadth

WASTE COUPLING FOR SINK Providing and fixing CP POP-UP HALF COVER Waste Coupling for kitchen of approved quality 38 mm dia of 83 mm length and 77mm breadth

TOWEL RACK Providing and fixing CP brass towel rack of dimension not less than : 240mm x 613mm x 115mm weight not less than 475 Grams shelf with min three bars and arrangement for keeping unfolded towels below the rack. Including fitting with concealed fittings arrangement of approved quality.

TOWEL RING Providing and fixing CP towel ring ovel shape minimum dimensions 21.4 x 1.5 x 14.4 Centimeters with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality , weighing not less than 88 gms.

BASIN MIXER supplying fitting and fixing of single lever CP brass basin mixer foam flow faucet with seven years warranty, shiny-reflective body finished of approved make including connection pipes from agnular stop cock and finished as per instruction of engineer in charge

SOAP TRAY Providing, fitting and fixing C.P. soap tray/ soap dish complete as directed and specified.

SINK COCK:Supplying fitting and fixing Chrome Plated (C.P.) sink cock of approved brand as directed and specified. (G.I. & C.P pipes will be measured and paid separately) (i) Sink cock with swinging casted spout

LIQUID SOAP DISPENSER Providing, fitting and fixing Liquid soap dispenser and liquid soap container complete as directed and specified. Fittings with glass bottle. Jaquar Model no. ACN-1137N or equivalent product from Hindware, Roca, Kohler.

COUNTER TOP WASH BASIN: Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls/ platfoMetre wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately)

HAND DRYER Supplying, installation, testing and commissioning of Automatic Jet Hand Dryer of following specifications and complete as per direction of Engineer in charge. Prior Approval of the brand should be obtained from the authority before supply of the product. • Colour : as per design Hindware / Jaquar/ Roca/ Kohler or Equivalent

HEALTH FAUCET Supplying fitting and fixing hand shower (health faucet) ABS with rubbit cleaning system, 1.25 m long PVC flexible tube with ABS wall hook and operating knob complete in all respects. Hindware (Cat No. F160013) Jaquar(Cat No. ALD-563) or Equivalent

CUBICAL TOILET:Supply and installation of Toilet Cubicles from reputed manufactureers (sylem, meriono, green etc.) made of 12mm soild compact laminated board. The solid compact laminate (phenolic core board) is based on theMetreosetting resins, homogeneously reinforced with cellulose fibres and is manufactured as per IS 2046. Top surface on both sides is melamine coated which shall be scratch and impact resistant. InteMetreediate panel should be continuous panel without any joints, all inteMetreediate panels, pilaster and doors shall be 12mm thick. The Size of the cubicles as per the layout of the toilet block and door opening of 600mm, overall height of the cubicle : 2020mm (including bottom gap of 150mm). All hardware, post etc. shall be of SS 304 grade. Including all necessary arrangements to fix the cubicals rigidly with the structural wall. Finished and complete as per the instruction of Engineer incharge.

URINAL PARTITION: Supply and installation of urial partions from reputed manufactureers (sylem, meriono, green etc.) made of 12mm soild compact laminated board. The solid compact laminate (phenolic core board) is based on theMetreosetting resins, homogeneously reinforced with cellulose fibres and is manufactured as per IS 2046. Top surface on both sides is melamine coated which shall be scratch and impact resistant. Overall height of the partition should not be less than : 1750mm (including bottom gap of 500mm). All hardware are shall be of SS 304 grade. Including all necessary arrangements to fix the partition rigidly with the structural wall. Finished and complete as per the instruction of Engineer incharge.

COWEL :Providing fitting and fixing PVC cowel of ISI make complete as directed and specified. (iii) 90 to 150mm dia. PVC cowel of ISI make

GRAB BAR: Providing, fitting and fixing CP Grab bar (600mm long). complete as directed and specified. Jaquar Model no. AKP-35711PS Roca Model no. RA816070165 Hindware Model no. F840012

BATHTUB: Supplying fitting and fixing bath tub including providing necessary fittings complete as directed and specified. (pipes will be measured and paid separately) iii) Poise Plain Acrylic Bathtub (Drop-in) C871246V (1700 x 750 mm) including Automatic Pop-up Waste and Self-draining System (C871899), Base Metal Frame (C871746)

BATH TUB MIXER: Supplying, fitting and fixing Chrome Plated (C.P.) Bath tub mixer with telephone shower arrangement only and crutch 20mm of Essco make complete as directed. Cat No.1180

PVC PIPES,BENDS,JUNCTIONS,TEES ETC. :Supplying, fitting and fixing PVC pipes of 6 Kg/csqm (Supreme/Prince) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia.

PVC PIPES,BENDS,JUNCTIONS,TEES ETC. :Supplying, fitting and fixing PVC pipes of 6 Kg/csqm (Supreme/Prince) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches.(ii) 110mm dia.

PVC PIPES,BENDS,JUNCTIONS,TEES ETC. :Supplying, fitting and fixing PVC pipes of 6 Kg/csqm (Supreme/Prince) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (iv) 75mm dia.

PVC PIPES,BENDS,JUNCTIONS,TEES ETC. :Supplying, fitting and fixing PVC pipes of 6 Kg/csqm (Supreme/Prince) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified.b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

PVC PIPES,BENDS,JUNCTIONS,TEES ETC. :Supplying, fitting and fixing PVC pipes of 6 Kg/csqm (Supreme/Prince) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified.b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (iv) 75mm dia.

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia.

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (iv) 75 mm dia.

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (iv) 75 mm dia.

Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia.

Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fiting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iv) 75 mm dia.

Supplying fiting and fixing 45 degree PVC bend of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.a) In exposed surfaces or in trenches. (i) 160mm dia.

Supplying fiting and fixing 45 degree PVC bend of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fiting and fixing 45 degree PVC bend of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.a) In exposed surfaces or in trenches. (iv) 75 mm dia.

Supplying fiting and fixing 45 degree PVC bend of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified.b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.(ii) 110mm dia.

Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches(i) 160mm dia..

Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches (ii) 110mm dia.

Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.(ii) 110mm dia.

Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages (iv) 75 mm dia.

Supplying fiting and fixing PVC single tee with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia.

Supplying fiting and fixing PVC single tee with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fiting and fixing PVC single tee with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches (iv) 75 mm dia.

Supplying fiting and fixing PVC single tee with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.(ii) 110mm dia.

Supplying fiting and fixing PVC single tee with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages (iv) 75 mm dia.

Supplying fiting and fixing PVC single ‘Y’ of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia.

Supplying fiting and fixing PVC single ‘Y’ of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches (ii) 110mm dia.

Supplying fiting and fixing PVC single ‘Y’ of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified a) In exposed surfaces or in trenches (iv) 75 mm dia.

Supplying fiting and fixing PVC single ‘Y’ of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages(ii) 110mm dia.

Supplying fiting and fixing PVC single ‘Y’ of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages (iv) 75 mm dia.

Supplying fiting and fixing PVC single ‘Y’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches (i) 110mm dia.

Supplying fiting and fixing PVC single ‘Y’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches (ii) 75 mm dia.

Supplying fiting and fixing PVC single ‘Y’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages (i) 110mm dia

Supplying fiting and fixing PVC single ‘Y’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages (ii) 75 mm dia.

Supplying fiting and fixing PVC double ‘Y’ plain of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 75 mm dia.

Supplying fiting and fixing PVC double ‘Y’ plain of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (i) 110mm dia.

Supplying fiting and fixing PVC double ‘Y’ plain of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 75 mm dia.

Supplying fiting and fixing PVC cross ‘T’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110mm x110mm

Supplying fiting and fixing PVC cross ‘T’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified a) In exposed surfaces or in trenches.(ii) 75 mm x 75mm

Supplying fiting and fixing PVC cross ‘T’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.(i) 110mm x110mm

Supplying fiting and fixing PVC cross ‘T’ with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages (ii) 75 mm x 75mm

Supplying fiting and fixing PVC coupler of (Supreme/ Prince)or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 110 mm dia

Supplying fiting and fixing PVC coupler of (Supreme/ Prince)or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iii) 75 mm dia

Supplying fiting and fixing PVC coupler of (Supreme/ Prince)or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (i) 110 mm dia

Supplying fiting and fixing PVC coupler of (Supreme/ Prince)or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (iii) 75 mm dia

Supplying fiting and fixing PVC reducer of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 160 mm x 110 mm

Supplying fiting and fixing PVC reducer of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iv) 110 mm x 75mm

Supplying fiting and fixing PVC socket plug of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. in exposed surface or trences as necessary complete at all levels including below G.L. as directed and specified.(a) 110 mm

Supplying fiting and fixing PVC socket plug of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. in exposed surface or trences as necessary complete at all levels including below G.L. as directed and specified (b) 75 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 15 mm nominal dia. Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 20 mm nominal dia. Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 25 mm nominal dia. Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 32 mm nominal dia. Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 40 mm nominal dia. Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 50 mm nominal dia. Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. : Concealed work, including cutting chases and making good the walls etc. 15 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. : Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal dia. Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having theMetreal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 25 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm nominal bore

Supply installation, testing and commissioning of borewll submersible pump with necessary pipes, fittings, electrical connections and accessories for lifting of water from a depth of 100m (depending on the water level availabilty under the ground) with flow rate at 720 LPM (for three hours of Running) one working one standby

Supply installation testing and commissioning of centrifugal pump (submersible/vertical/horizontal pump) of flow rate 220 LPM @ 50m head for block A(One working and one standby)

Supply installation testing and commissioning of centrifugal pump (submersible/vertical/horizontal pump) of flow rate 400 LPM @ 60m head for block B (One working and one standby)

PUMP Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, confoMetreing to IS-325. M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered with anti vibration pads. 2280 lpm at 56 m Head

JOCKEY PUMP FOR HYDRANT & SPRINKLER Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal confoMetreing to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, confoMetreing to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 180 lpm at 56 m Head

FIRE PUMP (DIESEL ENGINE DRIVEN) Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal confoMetreing to IS 1520. Suitable HP, 1500 RPM water cooled with radiator, diesel engine confoMetreing to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 2280 lpm at 56 m Head

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

ELECTRICAL WORK Supplying, laying, teMetreination & testing of undernoted sizes of copper conductor FRLS insulated both inner and outer sheath, PVC sheathed and sleeved 1.1 KV grade power distribution cables confoMetreing to relevant IS code and laying through and clamping the wall/racks/cable trays including dressing and clamping the cable with M.S. zinc passivated clamps etc. as required. 3C x 120 sq.mm

Supplying, laying, teMetreination & testing of undernoted sizes of copper conductor FRLS insulated both inner and outer sheath, PVC sheathed and sleeved 1.1 KV grade power distribution cables confoMetreing to relevant IS code and laying through and clamping the wall/racks/cable trays including dressing and clamping the cable with M.S. zinc passivated clamps etc. as required. 3C x 25 sq.mm

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 100 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Structural supports as required for cable trays complete with installation with anchor fastner/grouting as applicable. Painting with red oxide and 2 coats of enamel paint of colour as specified by Owner/Consultant.

Providing, laying, teMetreinations of copper wire and strip of undernoted sizes in surface for connection etc. with lugs. 8 SWG wire

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe confoMetreing to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 25mm

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe confoMetreing to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 50mm

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe confoMetreing to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 65mm

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe confoMetreing to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe confoMetreing to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100mm

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe confoMetreing to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150mm

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe confoMetreing to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 200mm (6mm thick)

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe confoMetreing to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 250mm (6mm thick)

Providing and fixing STRAINER Y type with M.S. flanged connection. 100mm 250mm (6mm thick)

Providing and fixing STRAINER Y type with M.S. flanged connection. 150 mm

Providing and fixing cast iron Dual plate spring loaded type non-return valve (as per technical specification) including nuts, bolts, 1.5mm thick CAF gasket sheets complete in all respects (PN 1.6) 80mm

Providing and fixing cast iron Dual plate spring loaded type non-return valve (as per technical specification) including nuts, bolts, 1.5mm thick CAF gasket sheets complete in all respects (PN 1.6) 100mm

Providing and fixing cast iron Dual plate spring loaded type non-return valve (as per technical specification) including nuts, bolts, 1.5mm thick CAF gasket sheets complete in all respects (PN 1.6) 150mm

Providing and fixing cast iron Dual plate spring loaded type non-return valve (as per technical specification) including nuts, bolts, 1.5mm thick CAF gasket sheets complete in all respects (PN 1.6) 200mm

Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets confoMetreing to IS 13095 of following sizes as required : 65 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets confoMetreing to IS 13095 of following sizes as required : 80mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets confoMetreing to IS 13095 of following sizes as required : 100mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets confoMetreing to IS 13095 of following sizes as required : 150mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets confoMetreing to IS 13095 of following sizes as required : 200mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets confoMetreing to IS 13095 of following sizes as required : 250mm dia

Providing and fixing G.M. stop valve ISI marked screws type tested as per IS: 778 of following size: 25mm

Providing and fixing gunmetal four way collecting head with 63mm dia instantaneous type inlet with built in check valve for fire brigade connection to underground tanks as per IS: 904.

Providing and fixing standard draw out connection with 63mm dia instantaneous type coupling and FOOTVALVE with all accessories as approved by fire authorities for installation at under ground tank.

SECTION-II: FIRE HYDRANT SYSTEM Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe confoMetreing to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 25mm

SECTION-II: FIRE HYDRANT SYSTEM Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe confoMetreing to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 32mm

SECTION-II: FIRE HYDRANT SYSTEM Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe confoMetreing to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 40mm

SECTION-II: FIRE HYDRANT SYSTEM Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe confoMetreing to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 50mm

SECTION-II: FIRE HYDRANT SYSTEM Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe confoMetreing to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 65mm

SECTION-II: FIRE HYDRANT SYSTEM Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe confoMetreing to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 80mm

SECTION-II: FIRE HYDRANT SYSTEM Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe confoMetreing to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100mm

SECTION-II: FIRE HYDRANT SYSTEM Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe confoMetreing to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 150mm

Providing and fixing black steel pipe to IS: 1239 (Heavy Class) including all fittings like anchor fastners, couplings, bends, elbows, tees, flanges, gasket etc. welding as required painting with coat of solvent based primer and wrapping with 5 layered corrosion protection tape 4.0mm or (4mm thick) confoMetreing to IS: 10221 including necessary earth excavation and refilling, masonary supports complete in all respect. (For under ground piping). 80mm

Providing and fixing black steel pipe to IS: 1239 (Heavy Class) including all fittings like anchor fastners, couplings, bends, elbows, tees, flanges, gasket etc. welding as required painting with coat of solvent based primer and wrapping with 5 layered corrosion protection tape 4.0mm or (4mm thick) confoMetreing to IS: 10221 including necessary earth excavation and refilling, masonary supports complete in all respect. (For under ground piping). 100mm

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe confoMetreing to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 150mm

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked confoMetreing to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Gunmetal

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. confoMetreing to IS 636 (type-A) as required : Gun Metal

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle confoMetreing to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Providing and fixing of gun metal 63mm dia short branch pipe , ISI marked (IS: 903).

Providing and fixing fire hose cabinet of size 900x600x300 fabricated from 16 gauge MS sheet of fully welded construction with hinged double front door with locking arrangements and partially glazed with 5mm thick glass stove enamelled fire red finish with fire hose written on front suitable to house 2x15 hose with couplings, one branch pipe (for external yard hydrants). Design to be got approved by Engineer-in-Charge before fabrication.

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, confoMetreing to IS 884 complete with the following as required. 20 mm nominal internal dia water hose theMetreoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve &nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m

Providing and fixing G.M. stop valves ISI marked screwed type tested to pressure as per IS: 778 of following sizes. 25mm

NON - RETURN VALVE with duel plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating for chilled / hot water circulation including insulation as specified. NON - RETURN VALVE of 150 mm dia

NON - RETURN VALVE with duel plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating for chilled / hot water circulation including insulation as specified. NON - RETURN VALVE of 100 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets confoMetreing to IS 13095 of following sizes as required : 80 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets confoMetreing to IS 13095 of following sizes as required : 100 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets confoMetreing to IS 13095 of following sizes as required : 150 mm dia

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection confoMetreing to IS 904 as required : 2 way-100 mm dia M.S. Pipe

Providing and fixing portable fire extinguisher, dry powder type (gas cartridge) with cylinder initially fully charged with dry powder (ABC type) of 6 Kg. Complete with standard discharge valve with tube, CI bracket for wall mounting etc. confoMetreing to IS: 2171.

Providing and fixing portable fire extinguisher carbon dioxide type with cylinder initially fully charged with CO2 gas of 4.5 Kg. Capacity, complete with discharge valve, dishcarge tube, horn, CI bracket for wall mounting etc. confoMetreing to IS: 2878.

Providing and fixing portable fire extinguisher mechanical foam type with cylinder initially fully charged with foam compound of 9 litres capacity, complete with standard discharge valve with tube CI bracket for wall mounting etc. confoMetreing to IS: 10204.

SECTION-III: SPRINKLER SYSTEM Providing, fixing, testing and commissioning of gun-metal ball valves ISI marked screwed type tested to pressure as per IS: 778 of following sizes: 25mm dia.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets confoMetreing to IS 13095 of following sizes as required : 100mm dia.

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets confoMetreing to IS 13095 of following sizes as required : 150mm dia.

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alaMetre, bronze seat clapper, clapper aMetre and hydraulically driven mechanical gong bell to sound continuous alaMetre when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required : 100mm dia

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection confoMetreing to IS 904 as required :

Point wiring : Point wiring in PVC conduit, with modular type switch - Wiring for light point / fan point / exhaust fan point / call bell point ( for door call bell only ) with 1.5 Sq.mm FRLS PVC insulsted copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 Sq.mm FRLS PVC insulated copper conductor single core cable etc as required. Conduit Make : Anchor / Richa or equivalent as approved. Wires : FR /FRLS - Finolex, RRKable, Anchor, Havels or equivalent as approved. Point wiring : Group B

Point wiring : Point wiring in PVC conduit, with modular type switch - Wiring for light point / fan point / exhaust fan point / call bell point ( for door call bell only ) with 1.5 Sq.mm FRLS PVC insulsted copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 Sq.mm FRLS PVC insulated copper conductor single core cable etc as required. Conduit Make : Anchor / Richa or equivalent as approved. Wires : FR /FRLS - Finolex, RRKable, Anchor, Havels or equivalent as approved. Point wiring Point wiring : Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required . for staircase lighting

Wiring for light/power plug with 2x2.5 Sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit alongwith 1 No. 2.5 Sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required for common corridor and stair case lighting for TV point SB ( having 2 nos. 5A switch and 2 nos. 5A socket ) and other 27 points as directed.

Wiring for 15/16A light/power plug for Gyser installed in the Toiler with 2x4 Sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit alongwith 1 No. 4 Sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required .Make : Anchor / Richa or equivalent as approved 4 Module (125mmX75mm)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required .Make : Anchor / Richa or equivalent as approved 6 Module (200mmX75mm) for TV (5A 2nos Switch with 5A 2 nos. Socket ) as directed.

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required .Make : Anchor / Richa or equivalent as approved 1or 2 Module Plate back plate with frame including GI box ( for TV & Telephone point, AC starter )as directed

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required .Make : Anchor / Richa or equivalent as approved 3 Module (100mmX75mm) for light power Point,

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including conections but excluding modular plate etc. as required. Make ; Havells/ Panasonic/ Schneider or equivalent as approved. 2 Nos. 5/6amp modular switch for TV / computer & net points

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including conections but excluding modular plate etc. as required. Make ; Havells/ Panasonic/ Schneider or equivalent as approved. 2 nos. 5/6 amps modular socket for TV SB 5 / Computer & net point

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including conections but excluding modular plate etc. as required. Make ; Havells/ Panasonic/ Schneider or equivalent as approved. 15/16 amps modular switch as required

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including conections but excluding modular plate etc. as required. Make ; Havells/ Panasonic/ Schneider or equivalent as approved. 15/16 amps modular socket as required.

5/6 amps switch and 3 pin 5/6 amp socket outlet for existing switch borad.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.FOR DOOR CALL

Supplying and fixing call bell switch for service call in the existing SB 3, complete as required.

e) 32A ,DP Electronic switch unit with key tag Key or with keycard with 30 sec Delay with plat 3M.

Modular Telephone Socket

Circuit / submain /Light plug wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required. Wires : FR /FRLS - Finolex, RRKable, Anchor, Havels or equivalent as approved 2 x 1.5 Sq.mm + 1 x 1.5 Sq.mm earth wire

Circuit / submain /Light plug wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required. Wires : FR /FRLS - Finolex, RRKable, Anchor, Havels or equivalent as approved 2 x 2.5 Sq.mm + 1 x 2.5 Sq.mm earth wire from DB to SB for room's and as directed

Circuit / submain /Light plug wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required. Wires : FR /FRLS - Finolex, RRKable, Anchor, Havels or equivalent as approved 2 x 4 Sq.mm + 1 x4 Sq.mm earth wire from DB to Geayse power point

Circuit / submain /Light plug wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required. Wires : FR /FRLS - Finolex, RRKable, Anchor, Havels or equivalent as approved 2 x 6 Sq.mm + 1 x 6 Sq.mm earth wire for sub main to SPN DB foMetre TPN floor maid DB

Circuit / submain /Light plug wiring in PVC conduit: Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required. Wires : FR /FRLS - Finolex, RRKable, Anchor, Havels or equivalent as approved 3 x 6 Sq.mm + 1 x 6 Sq.mm earth wire for sub main to SPN DB foMetre TPN floor maid DB

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required for service call indicating wires and TV co-axial cable inside only. Make : Anchor / Richa or equivalent as approved 20mm for TV co-axial cable and service call wire cable inside room from corridor only.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required for service call indicating wires and TV co-axial cable inside only. Make : Anchor / Richa or equivalent as approved 25mm for service call wires.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required for service call indicating wires and TV co-axial cable inside only. Make : Anchor / Richa or equivalent as approved. 32 mm dia

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in EXISTING recessed PVC conduit as required SERVICE CALL INDICATION. 1 x 1.5 sq. mm

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 12 Module (125mmX75mm) for service bell call indicator to be installed in Reception room

Supply and installation of service call indicator push buttom accept switch Make : Anchor 1M ( model no. 47683) or equivalent Havells/ CGL as approved.

MAIN POWER DISBRIBUTION BORD FOR BLOCK B Supply, installation, testing and commissioning of following LT distribution Panel Boards of 2 mm thick sheet steel cubical design for indoor WALL mounting factory fabricated suitable for operation on 440 V 3 phase, 50 Hz, A.C. supply with MCCBs/SFU/MCBs/ contactors, Extended rotary handles for MCCBs and other accessories, all in compartmentalised, cubical construction complete in all respects as per approved drawing and design including internal wiring, labels, ferrules, cable teMetreination gland plates, earth teMetreinals, painting etc. confoMetreing to specifications. ( Including civil works necessary for installaiton of the panel as reuired / directed ) for block B (SPECIFICATION AS PER ANNEXURE - III)

MDB for BLOCK A Incoming: Design, manufacture, supply, installation, testing and commissioning of cubicle type panel fabricated out of 14 SWG CRCA sheet steel , floor mounted totally enclosed switch baord suitable for use of 415 volts , 3 phase, 50HZ complete with aluminium bus-bar and all accessories including supply and fixing of following incoming and outgoing switchgears. The sheet steel shall undergo minimum 7 tank treatment followed by finishing powder coating of min 60 micron thickness Incomer: FP 400 A 50 KA Ics= 100% Icu MCCB with microprocessor based release with buit in E/F Protection, extended rotary handle and spreader teMetreinal - 2 Nos (.1 for ASEB supply and other for Generator supply having spreader link for connection to the incomming feeders ) Digital Ammeter 0-250A 3 Phase 4 Wire Accuracy Class 1 as per IEC 62053-21 Bezel dimension (W X H)=96 X 96 mm: 1 No. Digital Voltmeter - 0-500V 3 Phase 4 Wire Accuracy Class 1 as per IEC 62053-21 Bezel dimension (W X H)=96 X 96 mm : 1 Nos. CT 400/5 240V 3 Phase 4 wire Freq 50Hz+/- 5% Accuracy Class 0.5S : 1 Set SP MCB with 10KA breaking capacity of rating 6 Amp : 03 Nos RYB Indicating Lamps : 1 set (SPECIFICATION AS PER ANNEXURE - III)

Distribution Board - Supplying and fixing of following ways surface/ recess mounting, 240 V, SPN MCB distribution board of sheet steel,dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCB/ RCCB and incomer) as required. - for room and GF DBs. 6 way Double door 5 for food counter and 1 for washroom and 1 for cofee house and other places as directed.

Distribution Board - Supplying and fixing of following ways surface/ recess mounting, 240 V, SPN MCB distribution board of sheet steel,dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCB/ RCCB and incomer) as required. - for room and GF DBs. 12 way Double door

Distribution Board - Supplying and fixing of following ways surface/ recess mounting, 240 V, SPN MCB distribution board of sheet steel,dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCB/ RCCB and incomer) as required. - for room and GF DBs. 16 way, Double door .

Supply, Instalation, testing and commisioning of 4way V, TPN Double Door distribution board with MCCB incomer having fully insulated busbars and shrouded nutral bars, Earth bars, reversible door fesility, wih provision for instalation os DPX3 MCCB as incomer and SP/TPMCB as out going. (Including the supply of 50A, 25KA, DPX3160 MCCB) as required for conference, meeting room and dining hall AC power supply). Make ; legrand 5077 50VTPN DB or equivalent L & T, Havells as approved.

Supplying and fixing of following ways surface/ recess mounting,horizontal type, 415 V, TPN MCB distribution board of sheet steel,dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCB / RCCB and incomer) as required.- for each floor power distribution for rooms. 4 way (4 + 12), Double door for each floor & GF power distribution.

Supplying and fixing of following ways surface/ recess mounting,horizontal type, 415 V, TPN MCB distribution board of sheet steel,dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCB / RCCB and incomer) as required.- for each floor power distribution for rooms. 8 way (4 + 24), Double door for floor room & GF power distribution.

Supplying and fixing of following ways surface/ recess mounting,VERTICAL type, 415 V, TPN MCB distribution board of sheet steel,dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs for out gogoing and MCCB for incomming . (but without MCBs and incomer) as required.- for each counter power distribution. (Note : Vertical type MCB TPDB is noMetreally used where 3 phase outlets are required.) Make ; Havells, Panasonic, Schineider. as approved. 6 way (4 + 18), Double door for food counter and out door lighting power distribution. Having facility to install 63A TP MCCB as incommer.

Supplying and fixing following rating, pole, , MCB Isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. For room DB 40 amps DP 240 V

Supplying and fixing 5 amps to 32 amps rating, 240 volts, 'B' series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing 5 amps to 32 amps rating, 240 volts, 'B' series, miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole and neutral

Triple pole for TPN DB incomming and out door lighting

63A, 4P MCCB for incomminng feeder Make ; Havells, Panasonic, Schineider, as approved.

Supply and installation of 32A NO modular power contactor in exixting room DB.

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enamelled white on both sides, and with inscription in single red colour on front side as required for each electrical room door .

CABLE WORKS - Supply of following sizes of 1.1 KV grade single core/multicore aluminium conductor XLPE insulated and PVC sheathed aMetreoured / unaMetreoured cable confoMetreing to IS 1554 (Part-I) 1988.. Make ; RR Kable, Havells, Polycab, KEI Or equivalent as approved 3.5 Core, 300 sq.mm. XLPE AMetreOURED Aluminium Cable.

3.5 Core, 50 sq.mm. XLPE AMetreOURED Aluminium Cable.

3 Core,6 sq.mm. XLPE AMetreOURED Aluminium Cable. For Toilet block, Guard room power and cofee house power supply

4 Core, 16 sq.mm. XLPE UnaMetreoured Aluminium Cable

4 Core, 10 sq.mm. XLPE aMetreoured Aluminium Cable for street light our door feeder pillar SDB & panel earthing connection .

3 Core, 4 sq.mm. XLPE aMetreoured Aluminium Cable for external lighting.and earrace power supply

4 Core, 16 sq.mm. XLPE UNAMetreOURED COPPER Cable. For AC TPN DB

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioC70:C80ning, protective covering and refilling the trench etc as required. Up to 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioC70:C80ning, protective covering and refilling the trench etc as required. Above 35 sq. mm and upto 95 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioC70:C80ning, protective covering and refilling the trench etc as required. Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on surface of building walls addirected Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Upto 35sq. Mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Above 35 sq. mm and upto 95 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Above 185 sq. mm and upto 400 sq. mm

Supply and making cable end teMetreination with brass compression glands and crimped aluminium lugs following sizes of PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade of the following sizes as required. 3½ C X 300 sq. mm (45mm

Supply and making cable end teMetreination with brass compression glands and crimped aluminium lugs following sizes of PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade of the following sizes as required. 4 C X 50 sq. mm (35mm )

Supply and making cable end teMetreination with brass compression glands and crimped aluminium lugs following sizes of PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade of the following sizes as required. 4C X 16 sq. mm (45mm)

Supply and making cable end teMetreination with brass compression glands and crimped aluminium lugs following sizes of PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade of the following sizes as required. 4C X 10 sq. mm (19mm)

Supply and making cable end teMetreination with brass compression glands and crimped aluminium lugs following sizes of PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade of the following sizes as required. 3C X 4 sq. mm (19mm)

Supply & Installation of Light Fitting / Fans / Air conditioner / Geyser /Luminaries, Fixtures & TV. Installation, testing and commissioning of ceiling fan including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Supply and Installation of 1200 sweep very silent very powerful double bearing ceiling fan. Make ; Oirent Aeroquiet or equivalent Havells or Panasomic make as approved.

Supply and Installation of 1200 mm sweep white summer cool ceiling fan. Make ; Oirent summer cool or equivalent Havells or CGL make as approved.

Supply and Installation of 1400 mm sweep white summer cool ceiling fan. Make ; Oirent summer cool or equivalent Havells or CGL make as approved. For three baded room only (1a type)

Supplying and fixing stepped type elctronic fan regulator on the existing modular plate switch box excluding modular plate as required.

Providing and fixing extra conduit down rod of 20 mm dia, 2 X 10 cm length, wiring with 2 X 1.5 sq. mm FRLS PVC insulated,copper conductor, single core cable including painting etc. as required. (Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

Installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connections, testing, commissioning etc. as required.

Supply of 150mm high spped exhaust fan having automatinc lovour shutter . Make ; Oirent Ventilator HS or equivalent Havells, CGL or Panasomic make as approved. For Toilets

Supply of 300 mm high spped exhaust fan . Make ; Oirent or equivalent Havells, CGL or Panasomic make as approved. For Kitchens

Installation, testing and commissioning of prewired, flourescent fittings / all type of LED indoor ceiling fittings , complete with all accessories and tube etc. directly on ceiling/wall/ False ceiling, including connections with 1.5 sq.mm. PVC insulated, copper conductor, single core cable etc. as required.

Supplying of following LED lighting fixtures complete with Drive and Lamps with reflector/cover etc. complete as required:- Make : Sisk / CGL/ Havells/ Surya or Panasonic as approved Wall light 1 x 7.5 watt A60 LED Mske Havells LHFOAKD1TZ1C060 or equivalent Siska , CGL as approved .for bed side lamp

Wall light 2 x 7.5 watt A60 LED Mske Havells LHFOAFC2TZ1TO4O or equivalent Siska , CGL as approved .

Down light 2.5 inch dia round shaped recess 3 watt LED,WW (3K) SMD light fitting for night lamp Make Siska SSK-SMD- DLS or equivalent CGL/ Havells/ Surya / Panasonic as approved

Down light 6 inch dia round shaped recess12 watt LED,W (6.5K) light fitting for room lighting Make SISKA DLS 6 inch 15W or equivalent CGL/ panasonoc / HAVELS / SURYA as approved for room lighting

Down light square shaped recess / surface 12 watt LED,W (6.5K) light fitting for room lighting Make - CGL Pearl Ultima LSCSM 12W CDLor equivalent Surya, Siska, Havells, panasonic as approved for drawing corridor and staircase lighting.

Supply of 18W NW (6k) T8 LED tube light with compact commercial batten complete set as required . Make CGL Unilite or equivalent , Siska, Panasonic , Havells, Surya as approved. For car parking and Electrical room

Supply of 45 / 40 W LED W IP65 street light luminaries made out of die cast Aluminium housing and head frame, powder coated in approved color including driver and accessories as required. Make; Siska Ref Cat No. SSK ST 45W SN or equivalent CGL, Surya, Havells as approved. for terrace light .

Supply of angle holder with 12W LED bulb for terrace utility and lift room

Intergral round shaped surface mounted 9 watt W ( 6.5 K) white light Bulk head fitting for balcony lighting . Make SISKA BH 9W or equivalent CGL / HAVELS / SURYA as approved.

1 x 12 W LED T5 tube light fitting with drive and frame Make ;SSK T5 12W Siska COB DLC or equivalent CGL/ Havells/ Surya as approved. For study table lamp.

Intergral square shaped recess rhombus slim with of the tile makes seamlessly blend in with the ceiling space with geomatric and aligned design , the tile can be arranged in symmetric and abstract way to nmake the ceiling a peice of art for MEETING lighting room . Make CGL LCTLRF6-36 WW or equivalent SISKA / HAVELS / SURYA / Panasonic as approved.

Intergral square shaped recess mounted 6 watt WW ( 3/4 K) LED down light fitting with die cast aluminium housing finished with premium white powder coating for MEETING lighting room . Make CGL LSCMetre 6W- WW or equivalent SISKA / HAVELS / SURYA / Panasonic as approved.

Supply and installation of WW IP 65 LED RGB strip light on wall side post as directed (each strip is of 5 meter length ) Make ; Siska - SSK-ST-5560-RGB-IP EX-D or equivalent CGL, Havels, Jaquare as approved.

Supply of 20W LED out door drive suitable for the above stated LED strip lights.

Supply and installation of 25mm dia medium class GI pipe of 1m length having 120 degree angle bend for installaiton of above out door LED lamp set on the wall of the terrace romms as directed. The cost shall include all necessary clamp , nuts / bolts required to complete the job as directed.

Supply and installation of 15 Lts 5 star Geyser with necessary piping etc. as required to complete the job. Make : CGL AMICA or equivalent Smith / Jaquare. / panasonic as approved.

Supply and installation of 15 Lts Geyser with necessary piping etc. as required to complete the job. Make : CGL Solarium Cube or equivalent Smith / Jaquare.

Supply and installation of 32 inch Smart HD LED TV . Make : Sony, LG Samsung or equivalent as approved. 1for waiting hall and 75 nos. for each room.

Supply and installation of 1.5TR Dual Inverter type 5 star Air conditioner with necessary piping etc., Stabilizer free, HD filter as required in complete. . Make ; Dikin , LG, Blue Star.

Supply, installaton and testing & commissioning single phase 240V operated ceiling mounted 1.5TR X 2 nos. IDU inverter Cassette unit of multisplit type including 2 nos. cassette type indoor unit and one out door unit. The unit comprised of turbo inddor fan & BLDC motor. R410A prefilled regfigerant gas. with all necessary assessosaries to complete as required. Make ; LG / Dikin / Blue star.

Supply, installaton and testing & commissioning single phase 240V operated ceiling mounted 2TR. inverter . cassette type indoor unit and one out door unit. The unit comprised of turbo inddor fan & BLDC motor. R410A prefilled regfigerant gas. with all necessary assessosaries to complete as required. Make ; LG / Dikin / Blue star.

Supply and installation of modular 32A AC starter switch on exixting 2 module box.

Hospitality : DND MMR Unit Supply & installation of DND / MMR Control Unit having following indications - a) Clean my room b) Do not Disturb switch c) DND & DMR indication d) Laundry Switch e) 32A ,DP Electronic switch unit with key tag Key or with keycard with 30 sec Delay with plat 3M. f) 20A Shaver socket with 4 module plate DND MMR Internal Unit with above facilities

Hospitality : DND MMR Unit Supply & installation of DND / MMR Control Unit having following indications - a) Clean my room b) Do not Disturb switch c) DND & DMR indication d) Laundry Switch e) 32A ,DP Electronic switch unit with key tag Key or with keycard with 30 sec Delay with plat 3M. f) 20A Shaver socket with 4 module plate DND MMR External Unit with above facilities

4 Module Plate back plate with frame including GI box (for out door unit )

12 Module Plate back plate with frame including GI box ( for indoor unit)

Earthing & Lightening Arrestors Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. For MDB Panel & Lightning Arrester Earthing

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia cover plate having locking arangement and watereing pipe with charcoal / coke andsalt as required for out door lighting system & indoor DBs

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Providing and fixing of G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing of G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing earth bus bar joint made of 20mmx3mm thick 125 mm long with 6 nos. G.I bolts , nuts, chuck nut and spring washers etc. complete as requried

LIFT WORK 8 Pessangers Lift: Providing, erecting, testing and commissioning passenger lift without machine room on top in existing well including necessary scaffolding etc. as per the following specifications complete in all respects.Please note that the cost of the lift is inclusive of a warranty for 2 years. For detailed specifications refer SPECIFICATION AS PER ANNEXURE - II (8 pessangers, G+4 building)

13 Pessangers Lift: Providing, erecting, testing and commissioning passenger lift without machine room on top in existing well including necessary scaffolding etc. as per the following specifications complete in all respects.Please note that the cost of the lift is inclusive of a warranty for 2 years. For detailed specifications refer Annexure-II (13 pessangers, G+6 Building) SPECIFICATION AS PER ANNEXURE - II

FIRE ALAMetre SYSTEM Supplying, installation, testing & commissioning of heat detector operating at 54ºC/57ºC with rate of rise cum fixed temperature (dual theMetreistor) type with mounting base complete with all connection etc. as required for rooms

FIRE ALAMetre SYSTEM Supply, Installation,Testing & Commissioning of Analog Addressable Intelligent optical smoke detector with decentralize intelligence, soft addressable & sounder complete with base as required (for corridor & common places)

FIRE ALAMetre SYSTEM Supply, Installation,Testing & Commissioning of response indicator complete as required.

Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.

Supply, Installation,Testing & Commissioning of Addressable hooter cum strobe complete as required.

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections,interconnections as required. 4 zone

Supplying, drawing, connecting , testing of following single core PVC insulated FR copper wires in existing conduit for Fire alaMetre System. 2x1.5 sqmm

Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 20 mm dia

Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 25 mm dia

Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 32 mm dia

TELEPHONE WIRING WORKS Telephone Wiring Supplying & drawing following pair, 0.5 sq. mm. FR PVC insulated copper conductor, unaMetreoured telephone cable in the existing surface/ recessed steel / PVC conduit as required:- 2 Pair

Supply and installation of KRONE connector type main telephone tag block of following sizes in sheet metal enclosure of suitable dimensions fabricated out of 16 SWG sheet steel with castle key lock, hinged type cover including teMetreination of telephone cables, making connections, painting of box etc. complete as required:-( to be installed in 2nd. floor Electrical Room ) 50 Pairs

Supply of following poly ethyline insulated aMetreoured jelly filled telephone cables as per DOT specification. 20 pair 0.5mm dia aMetreoured copper telephone cable

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of Co- axial TV outlet on wall / partition including flush MS Box, front plate and jack complete as required. TV antenna socket outlet

Supplying and fixing of Splitter box in suitable size of G.I. Enclousure with cover plate including connections and making good the damage etc. as required. 2 way

Supplying and fixing of Splitter box in suitable size of G.I. Enclousure with cover plate including connections and making good the damage etc. as required. 3 way

Misecellineous Items - GI PIPES Supplying and embedding following G.I pipe of medium class for cable entry / road crossing of cable etc. including bending the pipe as required shape as required. a) 50 mm dia

Misecellineous Items - GI PIPES Supplying and embedding following G.I pipe of medium class for cable entry / road crossing of cable etc. including bending the pipe as required shape as required. b) 40 mm dia

Construction of 400mm x 400mm x 400mm masonry manhole with air tight C.I. Cover requires for earthing point to cover.

Fire Extenguisher Supply and istallation of 4.5 Kg, Mild steel ABC, A class powder/ CO2 type fire extenguisher

D.G.Sets - Supply, Installation and commissioning of following capacity 430V, 3-Phase Silent Diesel Generator Sets with auto run and auto change over facility. Make ; Cummins or CGL as approved. 1. 63 KVA

D.G.Sets - Supply, Installation and commissioning of following capacity 430V, 3-Phase Silent Diesel Generator Sets with auto run and auto change over facility. Make ; Cummins or CGL as approved. 2. 500 KVA

Submersible Cable - Supply of 3 core 6 sq.mm sub-mersible cable . Make Finolex or RR Kable as approved..

External lighting and CCTV system Indoor Main External Power Disbribution Board Supply, installation, testing and commissioning of following External LT power distribution Panel Boards of 2 mm thick CRCA MS sheet steel cubical design for indoor WALL mounting factory fabricated suitable for operation on 440 V, 3 phase, 50 Hz, A.C. supply with 24 Hrs. time switch/ MCBs/ contactors, and other accessories, all in compartmentalised, cubical construction complete in all respects as per approved drawing and design including internal wiring, inclusive of tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs for out gogoing , cable teMetreination gland plates, painting etc. confoMetreing to specifications as required. The panel shall have porvision of cable entry and out going at the bottom. The bus bar shall be sized with current density of Amperage 1A/sq.mm and MCB shall be connected using FR cables of proper rating. 24 Hours time switch 1 no. 63A TP, 36KA, MCB for incoming feeder 1 no 63 A NO TP Contactor 1 no.

Outdoor External power Sub -distribution Boards ( Out door lighting feeder pillar ) Supplying and fixing in PCC foundation of following out door feeder pillar for street light LT power distribution board , of 415 V, TP MCB, made of 2mm CRCA MS sheet steel,dust & rain protected, duly powder painted, inclusive of tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs for out gogoing confoMetreing to specificationsetc as required. The panel shall have porvision of cable entry andout going at the bottom. The bus bar shall be sized with current density of Amperage 1A/sq.mm and MCB shall be connected using FR cables of proper rating. 40 A TP Isolator for incoming feeder 1 no 200 A Bus bars Neutrar bar Earth bar 25 A, DP, 16KA MCB out gogoint 6 no ( 2 nos. in each phase) 200 A Aluminium Bus bars with heat shrinkable color coded PVC sleeves shall be of E91E grade. Neutrar bar Earth bar 40A TP, 25KA MCB for out go going 2 no. 25 A SP , 16KA, MCB for out gogoing 4 no

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enamelled white on both sides, and with inscription in single red colour on front side as required.

Supply of Streeet light, Post top lanterns, Garden lighting Fitting and Fixtures Supplying of following LED lighting fixtures complete with Drive and Lamps with reflector/cover etc. complete as required:- Supply of LED post top lamp set made of unbreakable poly carbonate suitable for mounting on pole fitting with drive and frame Make ;PRISM 40W (6K) Surya or CGL, Panasonic, Havells, phillips, Siska as approved for children park and back gate light. .

Supply of IP 54, 20W LED MID NIGHT BOLLARD, Make : Havells or equivalent Surya, Philips, Siska as approved.

Supply of IP65, 60W LED CDL decorative street light for beautification application. Make ; Empire ( Ref. Cat.No. LPTC 40 CDL) of CGL / Vega of Surya or equivalent Siska, Havells, Philips as approved.

Supply of 9W IP65 LED 6K GARDEN light in die cast aluminium housing with high qualify toughened glass diffuser for illumination of bush, garden etc.Ref. Cat No. SSK3005 12W 3K of Siska or equivalent Surya, CGL, Havels as approved.

Supply and installation of 9W 3K bush light in die cast aluminium housing with high quality toughened glass diffuser. Make ; Mallow of Surya or equivalent CGL, Siska , Havells as approved.

Supply and installation of 8 / 9 W 3K spike garden light in die cast aluminium housing with high quality toughened glass diffuser. Make SSK ;3771DZof Siska or equivalent CGL, Surya , Havells as approved.

24*0.5W WW LED IP54 wall light . Make Siska , SSK-3007 or equivalent Havells, Philips, CGL, Surya as approved.

36W UNIln - Line lite - having more safety and convenience of Installation vertically on gate pillars as directed. Make philips - BBP412 LED RGB 36W, 24V, L1200 GM with drive or equivalent Havells, Jaquare, Siska , CGL as approved.

Supply of 70 W LED W IP66 aerodynamically design made out of die cast Aluminium housing and head frame, powder coated in approved color including driver and accessories as required. . for B - block road side area Make; CGL make Ref. Cat No. Hawk Neo LSTN170 CDL AM or equivalent Siska , Panasonic, Surya, Havells as approved.

Installation of Light fittings Installation, testing and commissioning of prewired, LED out door fittings , complete with all accessories and tube etc. directly on ground / post top / walls etc as directed including connections with 1.5 sq.mm. PVC insulated, copper conductor, single core cable etc. as required.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in existing recessed steel/ PVC conduit as required for connection of light fittings to the bottom pole SMC box. 3 x 1.5 sq. mm

Supply and installation of IP55 Poly carbonate SMC box size 230mmx170mmx105mm door fixed hinged (make - syntex) with 6A DP MCB along with earth bar and necessary two nos. of clamps required to fit the box on the pole at required position or as directed .

External lighting system Earthing Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia cover plate having locking arangement and watereing pipe with charcoal / coke andsalt as required for out door lighting system.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

External Lighting pole Supply of GI pipe 40mm dia , 4.5 m length each of medium class for post top lamp pole with 1 no. 25mm dia hole for cable / PVC insulated wires entry for connection of luminaries installed on the top of the pole from the SMC box etc. as directed (total 4 nos. of pole) . ( pole height 3.5 meter above ground and 1 meter below ground )

Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required. Above 4.5 metre and upto 6.5 metre (for decorative stright light pole ) as diected.

Above 6.5 metre and upto 8.0 metre( for 8m height octagonal pole ) as directed.

Supply of GI pipe 50mm dia , 5m length medium class for lamp pole with 1 no. 32mm dia hole for cable / PVC insulated wires entry for connection of luminaries installed on the top of the pole from the SMC box etc. as directed.

Painting in double coat of above 5 M height GI pipe pole with black colour systhetic anamal paint as directed.

Supply of 8 mtr long galvanised octagonal pole with inbuilt JB arrangement HAVING DIN bar and Earth link bar (Top 70mm, Bottom 155mm, Thickness 3mm, Base plate 220x220x12 mm , 220 mm PCB. With single aMetre Make Crompton, Jindal, Niozon as approved.

Supply of Junction Box material- 16A DP MCB for above octagonal poles

Supply of 6 mtrs height decorative pole with inbuild decorative SINGLE aMetre matching with the lamps set as described above .Please refer CGL decorative pole catalogue for CGL set or for Surya make set please refer corwn decorative pole or as approved for other company make decorative set.

Supply of 6 mtrs height decorative pole with inbuild decorative DOUBLE decorative aMetre matching with the lamps set as described above. .Please refer CGL decorative pole catalogue for CGL set or for Surya make set please refer corwn decorative pole or as approved for other company make decorative set.

Providing and laying in position cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) in foundation of generators, external lighting feeder pillars, garden lights etc including frame works etc as directed. .

INSTALLATION OF CCTV CAMERA SYSTEM IP IR Dome Camera 6MP DS-2CD2163G0-IU 1/2.9" Progressive Scan CMOS ● 3072 × 2048@20fps ● H.265, H.265+, H.264, H.264+ ● Three streams ● 120dB WDR IR range: Up to 30 m ● IP66, IK10 ● Built-in micro SD/SDHC/SDXC card slot, up to 128 GB ● 3-Axis adjustment ● Built-in microphone 6 MP IR Fixed Dome Network Camera. MODEL CODE ; DS-2CD2163G0-IU or equivalent as approved.

DS-2CD2063G0-I 1/2.9" Progressive Scan CMOS BLC/3D DNR/ROI/HLC IP67 CAMERA Built-in micro SD/SDHC/SDXC card slot, up to 128 GB 3072 × 2048@20 fps 2.8/4/6/8 mm fixed lens Color: 0.01 lux @(F1.2, AGC ON), 0.028 lux @(F2.0, AGC ON), 0 lux with IR H.265+, H.265, H.264+, H.264 2 Behavior analyses 120dB WDR 6 MP IR Fixed Bullet Network Camera. MODEL CODE ; DS-2CD2063G0-I or equivalent as approved .

DS-2CD6362F-I(V)(S) 6MP Fisheye Network Camera 1/1.8” Progressive Scan CMOS  6 megapixel image sensor  Up to 3072 × 2408 resolution, real-time streaming  Multiple viewing modes  Line crossing and intrusion detection  Ceiling, wall or table mount modes  Up to 15m IR range  360° view angle  Built-in microphone & speaker  Audio/AlaMetre IO/ RS485(-S model)  IP66(-V model)  IK10 vandal proof(-V model) MODEL CODE :DS-2CD6362F-IS or equivalent as approved.

CAMERA INSTALLATION CHARGE

50 Inch LED FULL HD display 127 CM DIAGONAL MODEL CODE ; LH50AN3ND or equivalent.as approved.

6TB SATA HDD MODEL CODE ; ST6000VX001 or equivalent as approved

16 Port PoE Switch : MODEL CODE : DE3E0518P-E or equivalent as approved.

6U Wall mount rack with all accessories. MODEL CODE : NWR-6U-5045-GR

CAT6 out door networking UTP Cable. MAKE CODE ; NCB-C6UGRYR-305

RJ45 Connector. MAKE CODE NPG-5E1TRA031-100

Supply of octagonal 6 mtr height GI pole base dia 130 mm and 70mm top dia with base plate and nuts and bolts etc. as required.

Installation of all items including errection of poles with PCC foundations, Laying of CCTV cable on OH or under ground by using HDP pipe etc. as required . This also include intallation of cameras and other ancillary works with necessary clamps as required as per standard procedure and as directed - a lot

NVR RACK AND OTHER ACCESSORIES a lot of work

EXTERNAL ELECTIRCAL WORKS: TRANSFORMER : Supplying, installation testing and commissioning of the following rating copper wound out door type transformer. Transformer should be as per CEA / BIS guidelines as ammended up to date for losses along with LV enclosure .Including required load security as per applicable norms of service provider ( APDCL). 800 KVA, 50Hz. 11/0.433 KV. Oil filled LEVEL 2, 4 STAR ,COPPER WINDING transformer .

Providing and laying in position cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) in foundation / transformer pad of above transformer etc including frame works etc as directed. .

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying double run 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection terminating with nut, bolt, spring, washer etc. as required.

G.I. swaged steel tubular pole 'SP-60', 12 meters length, coated with black bituminous paint (internally & externally) up to the earth level , with 14 mm. diameter through hole for earth connection, including grouting with concrete (1:2:4) on steel base plate.

G.I. channel cross arm 100 x 50 x 6 x 2200 mm.

G.I. angle 50 x 50 x 6 mm. for guard bracket

G.I. 'T'-cross arm (angle size 50 x 50 x 6 mm) for 11kV

G.I.Hook - GI

11 kV grade composite polymer long rod (disc) insulator (70 kN, tongue & clevis type), 320 mm. minimum creeepage distance, with FRP rod core, silicone elastometric compound housing and weathersheds, metal end fittings, etc. as per technical specification

11 kV grade composite polymer pin insulator, 320 mm. minimum creeepage distance, with FRP rod core, silicone elastometric compound housing and weathersheds, including G.I. pins, etc. as per technical specification

ACSR 'Racoon' conductor

Tension clamp for ACSR 'Racoon' conductor

G. I. wire 8 swg. for guarding

G. I. wire 8 swg. for earthing (every pole to be earthed)

G.I. perforated earth pipes, 50 mm. NB diameter x 3.6 mm thickness x 3 meters length for conventional earthing OR for rocky areas, G.I. perforated earth pipe, 50 mm. NB diameter x 3.6 mm thickness x 3 meters length with chemical earthing. Earthing as per latest amendments of Indian Electricity Rules 2003

G.S. stay set with 50 x 8 mm. stay clamp; 2 no. pocelain guy insulator; anchor plate (6mm. thick x 200mm. x 200mm.); 2 no. turn buckles; 16mm. diameter x 1.8 meter long galvanized steel solid stay rod and 7/3.15 mm. stranded G.I. stay wire; etc.

PG clamp, for ACSR 'Racoon' conductor

Danger plate '11000 volts'

G.I. M16 bolts, nuts, washers and spring washers (assorted)

Galvanized steel barbed wire 12 swg. x 14 swg., spiral length 1.5 meters minimum

Pole clamp for G.I. flat 50 x 6 mm.

Jointing sleeve for ACSR 'Racoon' conductor

11KV D.O Fuse 150 Amp

12KV, 9KA Linghtning Arrestor line type

11 KV goab Switch , 400Amp

4 P, MCCB 400A, Ics = 100% Icu

11KV, combined CTPT Set

10- core 2.5 sq.mm Cu. Control cable

Copper wire 6 SWG for earthing

Metering cabinet

HT Trivector meter

Bi mettalic Lug

AMR Modem with acessories

Sundries L/S

Cost of transportation & storage on materials, labour charges, contingency and supervision charges

Gypsum ceiling: Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @

230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

GRID FALSE CEILING: Supply and installation of false ceiling as per the architectural drawings (plan and sections) with Silhouette 15 mm exposed grid system (ISI marked) of 600x600 mm module shall include wall angles with unequal flanges of size 14&20 mm and 0.40 mm thick (minimum dimensions) fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300 mm center to center. The main member, having flange width 15 mm, height 30 mm (minimum dimensions) should be suspended from the immediate roof with help of soffit cleat and wire rod etc. and leveling spring clip at 1200 mm c/c or as required. Cross member having flange width 15 mm, height 30 mm (minimum dimensions) are to be fixed and interlocked into the pre-cut slots in the main member at 600 mm c/c in the perpendicular direction. The cross silhouette having flange width 15 mm, height 30 mm (minimum dimensions) are then interlocked into the pre-cut slots at 1200 mm c/c in parallel direction to the main member. Steppe edged acoustical board of 15 mm thick (minimum) shall be placed into the grid size of 600x600 mm properly with necessary clips and other accessories as required.

The size of the board should be 595x595. The work should be executed in accordance with the drawing and prior necessary discussion with electrical, A/C installation team and other vendors as required. Finished and complete in all levels/respects as per the directions of Engineer In-charge. Technical Parameters of Ceiling Board : The board should contain at least the following properties. a) Non metallic Acoustical Board: • Core - Glass fibre/ Mineral fibre • Fire Resistant: 1/A Class Fire Rated. • Acoustical property – NRC; 0.70 to 0.85 • Termite resistance • Light reflectance – 81 - 85 % • Strength - Antisag • Colour : Pre-painted with approved colour.

Extra over item NS 1/1.1, for providing Perforated Metallic Acoustical tiles/board in place of Steppe edged acoustical board to fix light fixtures, AC diffuser, trapdoor etc where applicable. Including cutting holes/slots for light fixtures, A/C inlet and outlet vent/grill/diffuser as per the approved layout. Technical Parameters of Ceiling Board : The board should contain at least the following properties. b)Perforated Metallic Acoustical Board: Perforation - Diameter : 1.8 mm to 2.5 mm, Total Open Area : 16% to 20 % , of approved colour, hot pressed sound absorbent fleece to the back of the tiles to obtain acoustical property not less than NRC 0.70.

Mineral Fibre False Ceiling (Antimicrobial): Providing and fixing mineral fibre tiles false ceiling at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised @80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod upto 1000mm length and L-hape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be prepainted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge.With 16 mm thick beveled tegular mineral fibre Antimicrobial false ceiling tile confirming to ISO 5 (class 100 ) specifications.

BAMBOO WOOD CEILING:Providing & fixing in position Phenol bonded Bamboowood tiles (Made In India) with tiles of size 8 mm thick,1800 mm length (minimum) and 130 mm wide (minimum) used in False Ceiling Work, Bamboowood tiles having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC) with necessary profiled edges; placed under covered shed as suspended ceiling on GI open grid system. Frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 as per IS : 277 and consisting of intermediate channel of 15x45x15x0.90 mm size running parallel at 900 mm centre to centre distance and connected with same intermediate channel at 457 mm c/c perpendicular and fixed together with screws and also held in position with GI ‘L’ section of 38x38x1 mm thick of length 38mm with screws.Bamboowood tiles 4nos per set having 5 mm gap between two tiles and connected together with BWR grade ISI mark plywood of section 50x12 mm, two at ends and three in centre after applying D3 category adhesive underside of ply batten and screwed from backside and covered with 2 mm expanded polyethylene foam as upperlayment and held in place.

GI ‘’ section 24x38x0.9 mm base screwed to plywood section on both sides and fixed with frame work with 2.64 mm dia connecting clips and GI fixing bracket of slotted soffit cleat sie 27x37x25x1.6 mm through channel and fixed with tapping screws to ‘’ frame to held in position. Whole frame work held in suspended form with dash fasterner 6 mm x 50 mm with 4 mm dia GI hanger rod having adjustable butterfly clip for levelling and connected with roof truss/ slab with cleat and rawl plugs at 900 mm c/c. All ceiling made smooth level at lending and tray ceiling as well. Bamboowood tiles in ceiling and ceiling frame all held in place as per manufacturers design details and finished to smooth as complete ceiling. The Bamboowood tile panels shall have minimum density of 1000 Kg/cum & minimum Hardness 1000 Kgf. and finished with Eco friendly UV coating, all complete as per direction of Engineer in- charge.

Acoustical Wall paneling: (Upper Part) : : Supply & Installation of Kerf edged, fabric wrapped wood fiber/ glass fibre panels of size 600x1200x20mm (minimum) having density 400Kgs/m3, weight 8kg/m2 installed at 2100mm from finished floor level to ceiling by using GI strut system as per the design and Architectural drawings. The GI strut work includes cross channel having thickness 0.45mm (minimum), of required length, knurled web 40mm (minimum), depth 22mm (minimum) and equal flanges 10mm (minimum) are to be fastened to wall horizontally in a regular manner at 600mm c/c. PVC Vinyl core UV treated H-spline having thickness 2mm (minimum) and of required length to be fixed perpendicular to the cross channel at 600mm c/c. The Kerfed edge panels shall be then inserted into the H-spline against wall to perfect fit Including all other accessories like wooden beads, screw etc. to finish and complete as per the Architectural drawings and directions of Engineer In-charge. Technical Parameters : • Core - Pinewood fibre/ Glass fibre • Fire – Class 1 & P • Acoustics – NRC: 0.07 to 0.95 • Termite resistance • Light reflectance – 75 % • Colour - As approved

Acoustical Wall paneling: (lower Part): Supply & installation of slats, made of pinewood core, E1 grade fiber board, melamine/veneer laminated finished of approved colour and shade, grooved and perforated slats 16-2 (2mm groove @16mm pitch) and 32-2 (2mm grooves @ 32mm centers) (minimum dimensions) where applicable of approved colour and shade as per design up to the height of 2100 mm from finished floor level. The slats should be backlined with black acoustical fleece with following properties. All the joints of the slats should have tongue-groove edge for a seamless look. The size of slats should not be less than 128 width,16mm thick of required length. The base density should not be less than 800Kg/m3, weight 10Kgs/m2. Installation should be in GI strut system which includes GI cross channel having thickness not less than 0.45mm (minimum) of required length, knurled web 40mm (minimum), depth 10mm and equal flanges 15mm is fastened vertically/horizontally at every 600mm centers. Aluminium core cross channel having thickness not less than 0.5mm, web 15mm & 27mm, depth 18mm and flanges of 7mm (minimum dimensions) with suitable edge & center brackets is then fixed perpendicular to the cross channel with the help of fasteners at every 400mm centers. Slats of required size are then fixed perpendicular to cross channel with suitable edge & center brackets.

There should be expansion joints of 3mm at every 5mtrs in both horizontal and vertical directions. Including all other accessories like wooden beads, skirting's, screws etc. to finish and complete as per the Architectural drawings and directions of Engineer In-charge. Technical Parameters : • Core Variants - Pinewood E1 Fiberboard • Fire – Class 1 & P • Acoustics – NRC up to 0.75 • Light reflectance – 75%

WALL PANELLING WITH CONCEALED METAL (G.I. SECTION) FRAMEWORK: Providing and fixing concealed G.I. sections for wall lining with Everest Non-Asbestos Fibre Cement Board confirming IS – 14862, which includes 6mm plain board(for dry area) / 6mm designer board ( Lake & Hill, Oceanic, Casecade, Electra) / 6mm Heavy Duty plain board(for wet area) of M/S Everest Ltd., fixed on the ceiling section (0.55mm thick having a knuled web of 51.5mm and two equal flanges of 26mm each with lips of 10.5mm made of G.I. steel) placed at 610mm center in perimeter channel (0.55mm thick having one flange of 20mm and another flange of 30mm and a web of 27mm made of G.I.steel) fixed to the floor and ceiling with nylon sleeves & wood screws at 610mm c/c with fully threaded self-tapping screws all complete as per the drawing & directions of Engineer- in-charge The boards may be finished so as to have a uniform groove finished with expansion filler. Alternatively, grooves / joints can be covered with decorative molding/jointing compounds to have a uniform flush finish. Finally, if specified, the boards can be painted with 2 coats of acrylic emulsion paint of approved shade over a coat of cement primer. 6 mmEverest Designer FC board

WALL PANELLING WITH WATER PROOF PLY: Providing and fixing water proof ply wood board ( aproved brand) 6 mm, 12 mm and 19mm where applicable for wall panelling works as per approved design and drawing with required wooden or ply board supprt frame including necessary 10 to 12 wide SS bead, nail, screw, adhesives and complete as per instruction of engineer in charge. (The wall paneling shall be finished with 1.5 mm thick laminates, PU polished 4 mm thick veneer, wall paper, texture paints which will be measured and paid extra.)

BAMBOO WOOD WALL CLADDING:Providing & fixing in position Phenol bonded Bamboo Wood Wall Cladding at all height with planks of sizes 10mm thick, 100 mm minimum width and of required length as per the Architectural design. The plank made out of Eco friendly Bamboowood of ESES or equivalent brand (made in India ) with necessary profiled edges; placed on walls. The bamboo wood planks shall have minimum density of 1000 kg/cum & minimum Hardness 1000 Kgf. Bamboowood panels and frame all held in place as per manufacturers design details. Including necessary concealed screws, nails and other accesories required to fix the planks in position either existing frame work or other flat surface like ply, cement board. (frame work or surface will be measured and paid separately) and finished to smooth as complete wall cladding as per direction of Engineer in-charge.

TEAK WOOD PANELING: Providing and fixing in position teak wood paneling of 12 to 20 mm thick (where applicable) and required width and length (length not exceeding 2500 mm) over a smooth and regular surface of water proof ply board (12 mm thick, approved brand) with necessary groove and other design/ pattern as per the architectural need and drawing in straight, curve and any other shape. Sides of the board and wooden plank are to be cover with a wooden bead. All the exposed wooden surfaces are to be finished with 40: 60 PU polish of approved colour. Including provision for fixing light fixtures (if any) and complete as per instruction of engineer in charge.

DECORATIVE PARTITION: Providing and fixing first class timber framed of size required by the design and water proof ply wood board ( approved brand) 6 mm, 12 mm and 19mm where applicable for wall paneling, partition or space divider works as per approved design and drawing with required wooden or ply board support frame including necessary nail, screw, adhesives. The exposed timber frames are to be finished with 40: 60 PU polish and ply board surfaces are to be covered with handloom fabric of approved design and shade. Necessary foam inlay are to be incorporated to bring the architectural design of the surface. Including the cove or any other design for fixing light fixtures and complete as per instruction of engineer in charge.

VENEER: Supplying designing and laying 4mm thk. Veneer of approved shade and colour of recomanded brand on door or any other vertical and horizontal, wall and ceiling (ply, cement board, MDF, WPC) surface to be decorated as per approved drawing and view to obtain the desired architectural element. Necessary SS bead of 10 to 12 mm wide and required thickness to be fixed as per the design with high perfomance adhesive, concealed screw etc. the veneered surface should be finished with 40:60 PU polish from repued brand like Asian, Berger ect. Incluing necessary scaffolding finished and complete as per instruction of Engineer in charge.

LAMINATES: Supplying designing and laying 1.5 mm thk. laminates of approved shade and colour of recomanded brand on door or any other vertical and horizontal, wall and ceiling (ply, cement board, MDF, WPC) surface to be decorated as per approved drawing and view to obtain the desired architectural element. Necessary SS bead of 10 to 12 mm wide and required thickness to be fixed as per the design with high perfomance adhesive, concealed screw etc. the laminated surface should be finished with 40:60 PU polish from repued brand like Asian, Berger ect. Incluing necessary scaffolding finished and complete as per instruction of Engineer in charge.

FLUSH DOOR: Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevent I.S code including 4 numbers SS hinges of size: 100 X 75 X 3 mm having 2 high perfomance ball bearing (refer: Hafele article no. 926.32.160) from reputed brand like Hettic, Hafele, Godrej etc. with necessary recomended screws. The edges of the door should be covered with a hard wood timber bead of required width and 6mm thick to be finished with 40:60 PU polish. Decorative type face panel and block board core. 35 mm thick. (The flush door shall be finished with 1.5 mm thick laminates, PU polished 4 mm thick veneer or mirrior where applicable and same will measured and paid extra.)

FIRE RATED DOOR: Providing and fixing plain wood finish door with door frame conforming to IS 4351:2003. The thickness of the door should not be less than 30mm where the inner core is from 150gsm thick Honeycomb paper having load bearing capacity of minium 500kg/sqm. The door frame of section 100mmx58mm made of 1.2mm-2mm thick pre-galvanized steel sheet conforming to IS 4351:2003 where the inner core is filled with Polyurethane foam (PUF). The door shutter shall be made from 1.2mm-8mm thick slip coated pre-galvanized steel sheet conforming to to ASTM A527/ASTM A525, JIS G 3302 or BS 2989 1994, IS 277. It shall have 80-120 gsm of zinc coating having lock formed panels with 3mm thick internal stiffeners made of GP. The door shutter shall constitue of minimum 3mm thick hinge reinforcing with hardware mounting plates and lock protection. The door surface shall be finished with powder coating of thermosetting Polyurethane paint of Aliphatic Grade providing high levels of scratch resistance and durability/epoxy polyester/pure polyester/polyurethane powder of thickness 60-65 microns. Narrow vision glass made of 6mm clear float glass of required shape and size shall be incorporated wherever applicable as per the Architectural drawings . All necessary hardware and fittings like hinges, locks, flush bolts, door closers, door handle, door stopper, wall protector etc. should be of recommended brand. Finished and complete as per the drawing, specification and instruction of Engineer In-charge. Size - 1500x2400 External (Double Leaf Door with Narrow vision Panel)

SLIDING GLASS DOOR WITH SENSOR: Supplying materials and installation of frame less glass/ powder quoted aluminium frammed glass partition with 12 mm thick toughened glass (in case of frame less), 6 mm thick glass (in case of framed) as per the Architectural drawing and design, including all necessary stainless steel glass architectural hardware and necessary framework above ceiling to support glass hardware to fix the partition rigidly at it's position. The provision of glass sliding glass door are to be kept according to the Architectural design need. Including supplying and installation of the door of specific size and type, necessary hardware, fitting and fixtures for doors should be from recommended brand like Dorma, godrej or equivalent. Approach sensor micr or motion- detector sensor owave pulse or passive infrared control etc. are included and should also be from approved manufacturer and compatible with the weight of the door (Manufacturer recommendation necessary). The fixing and lifting of glass of required width/length is the sole responsibility of the contractor. Including all other supporting items like silicon based adhesives, locking arrangements if any and complete as per the directions of Engineer In-charge. Technical Parameters of Sensor : Opening speed : 10 to 50 cm/sec (Incrementally Adjustable) Closing speed : 10 to 40 cm/sec (Incrementally Adjustable) Hold-open time : 0.5 to 30 sec (Incrementally Adjustable) Usage/Application : Single Panel Sliding Door, Double Panel Sliding Door (Bi-Parting) Clear Passage Width : Single Sliding = 800-1200mm, Double Sliding = 1000-2000mm Clear Passage Height : 2400 mm (Recommended) Max.Door Weight : Single Sliding = 1 x 100 Kgs. Single Sliding = 2 x 85 Kgs. Activator Options : RADAR Sensor,Pushbutton,Hand held Transmitter/Receiver (Remote Control) Program Switch Modes : Off/Automatic/Permanent Open, Partial Open, Exit Only Power Supply Data : 230 VAC, 50/60 Hz (mandatory UPS/stabilized supply) Operator Mounting : Only Face Mounted a) Full height glass partition with sliding door including sensor.

OPENABLE GLASS DOOR: Supplying materials and installation of frame less glass partition with 12 mm thick toughened glass as per the Architectural drawing and design, including all necessary stainless steel glass architectural hardware and necessary framework above ceiling to support glass hardware to fix the partition rigidly at it's position. Necessary hardware, fitting and fixtures for doors should be of recommended brand like Dorma, godrej or equivalent. Installation of floor spring, door closer, door handle (H-type back to back; 400mm-500mm overall length), sensor control etc. are included and should also be from approved manufacturer and compatible with the weight of the door (Manufacturer recommendation necessary). The fixing and lifting of glass of required width/length is the sole responsibility of the contractor. Including all other supporting items like silicon based adhesives, locking arrangements if any and complete as per the directions of Engineer In-charge. a) Full height glass partition with openable door.

BATH ENCLOSURE : Supplying materials and installation of bath enclosre with 6 mm thick toughened glass as per the Architectural drawing and design, including all necessary stainless steel glass architectural hardware and necessary framework to fix the partition rigidly at it's position. The provision of door is to be kept according to the Architectural design need. Necessary hardware, fitting and fixtures should be mat finished SS 304 and from recommended brand like Dorma, Godrej etc. Installation of towel bar of 25 mm dia, 450 mm, 200 mm long (reference: hafele article no. 980.47.000) included and should also be from approved manufacturer and compatible with the weight of the door (Manufacturer recommendation necessary). The fixing and lifting of glass of required width/length is the sole responsibility of the contractor. Including all other supporting items like water sealed transperant pvc rubber guskae, silicon based adhesives and complete as per the directions of Engineer In-charge.

WPC DOOR FRAME Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 26.86.5 Frame size 65 x 100 mm

Glass film /Glass paper : Supplying and installation of good quality commercial Glass film/ Glass paper from brand having good market track record over last five years, of approved colour, pattern and design (where applicable) and fixed with proper adhesive. The joints of Glass film/ Glass paper should not be visible in any case. Complete and finished in all respect and as per the directions of Engineer in-charge. (Minimum MRP of the product should not be less than Rs. 1000.00 per Sqm) only

Wall Paper: Supplying and pasting of Non-Woven wallpapers of approved make and design with advanced technically improved wallpaper material of brand having good market track record over last five years. The wallpaper should made of a fibrous material, non-woven wallpapers which is easy to install over any smooth surface and also easy to remove without damaging the base surface. The material should vinyl/ environment friendly wallpaper option. Inclusive adhesive, liner if necessary and complete in all respect as per the instruction of Engineer in charge.(Minimum MRP of the product should not be less than Rs. 1000.00 per Sqm) only

Wall fixed Cup board: Providing and fixing wall fixed cupboard as per the following specification Inner body: Inner body of the cupboard should be made out of WPC (Wood Polymer Composite) solid plain white colour board comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/wheat husk) and nontoxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/moisture proof and fire retardant and fixing to the smooth wall surface finished with wall putty and two coats of cement primer. The shelves and drawers are planned as per the requirement to keep clothes and other belongings of residential use. All the exposed edges are to be finished with 2mm thick 16 to 19mm wide PVC/paper edge binding of approved quality including necessary synthetic resin hot pressed to edges on binding machine having property of providing uniform and integrated look. The inside top surfaces of the WPC boards are to be finished with plastic/ acrylic laminates of min 1.00 mm thick. Measurement will taken on the front area i.e. Height X Width of the cupboard. Depth of the cupboard will not be considered for measurement in any case.

Accessories: Accessories like drawer slider, rob hock, hanger bar, trouser pull, door handle out etc. complete; should be of SS mat finished and from approved brand like Hafele, Hettic, Godrej or equivalent. Sliding front door track (where applicable) should be of sound less, aluminum made channel as preapproval of the authority. A digital safe deposit vault of 300mmX300mm is to be fixed where applicable (the vault will be measured and paid separately). All locking arrangement should be hassle free and product should be from reputed brand like Hafele, Godrej or equivalent. Handles, nobs etc. should not have any sharp edge/ corner and should be from reputed bran like Hafele, Godrej, Ozon or equivalent. Including all required ball bearing and other accessories to make the wall unit user friendly. Wardrop rails should be from reputed brand like Hettich, Hafele of matching colour. Quated rate should be inclusive of both the cubical and accesories.

Ply made Cupboard Door/ Palla: Door made out of 19 mm thick approved quality water proof ply finished internal surfaces with 1.5 mm thick laminates (white in colour) of approved designed, shade and brand fixed with approved adhesive. The edges of the ply board should be covered with 6 mm thick wooden bead finished with 40: 60 PU polish. The exterior surface of the door should be finished with 4 mm thick veneer board approved colour and shade from reputed brand fixed with approved adhesive. Including counter sung screw, 125 mm SS mat finished cupboard handle, nobs locking armament etc. should be from reputed brand like Hafele, Hettic, Godrej or equivalent. Probable Cut, grove, double layer veneer of different shade etc. are to be considered while quoting the rate. The veneer surfaces are to be finished with 40: 60 PU polish. Finished and complete as per instruction of engineer in charge.

Particle board cup board palla: Door made out of both side laminated (inner side white and outer side of approved shade) 19 mm thick particle board from reputed brand approved by the authority to be fixed to the existing WPC cupboard body fixed with smooth closing concealed hinge 110 degree opening angle side-on hinges with automatic closing spring, with 3dementional adjusting facilities fit for 19 mm thick door. Including Providing and fixing 2mm thick 19mm wide PVC/paper edge binding tape of approved quality for cupboard/wardrobe shutters including necessary synthetic resin hot pressed to edges on binding machine, counter sung screw, 125 mm SS mat finished cupboard handle, nobs locking armament etc. should be from reputed brand like Ozone, Dorma or equivalent. Finished and complete in all respect as per the instruction of engineer in charge.

Aluminium Cupboard Shutter: Providing and fixing Klar Door from reputed manufacturer like Hettich, Hafele, or equivalent with Klar Door Hinges especially designed in slim form, hinge enables soft closing of the door for silent operation equipped with a soft closing mechanism ensuring silent closing of cabinet doors making way for peaceful operation with approved frame colour (Brushed Stainless Steel, Brushed Black Material) with minimum profile thickness 19.2 mm and weight not less 0.60 kg/meter. Clear float glass, Milky white , mirror or any other coloured glass as per the approval of the authority of thickness 4-5 mm. Glass cabinet doors complete with PVC black finished C shaped gasket for 5 mm glass, filler gasket for 4 mm glass, Corner Connector Countersunk Screws etc. All fixtures should design to withstand an overall weight of the shutter (glass and profiles) should be 20 kg.

MARBLE TOP CUPBOARD: Cupboard, body made out of WPC (Wood Polymer Composite) solid plain white colour board comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/wheat husk) and nontoxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/moisture proof and fire retardant and fixing to the smooth wall surface finished with wall putty and two coats of cement primer. The shelves and drawers are planned as per the requirement to keep pantry equipment and other belongings of residential use. All the exposed edge are to be finished with 2mm thick 16 to 19mm wide PVC/paper edge binding of approved quality for cupboard/wardrobe shutters including necessary synthetic resin hot pressed to edges on binding machine having property of providing uniform and integrated look. The inside top surfaces of the WPC boards are to be finished with plastic/ acrylic laminates of min 1.00 mm thick. Top and side visible surfaces are to be finished with good quality mirror polished Italian marble with beveled cutting. Measurement will taken on the front area i.e. Height X Width of the cupboard. Depth of the cupboard will not be considered for measurement in any case.

Accessories: Accessories like drawer slider, rob hock, hanger bar, trouser pull, door handle out etc. complete; should be of SS and from approved brand like Hafele, Hettic, Godrej or equivalent. Sliding front door track (where applicable) should be of sound less, aluminum made channel as from approved brand like Hafele, Hettic, Godrej or equivalent preapproval of the authority. A digital safe deposit vault of 300mmX300mm is to be fixed where applicable (the vault will be measured and paid separately). All locking arrangement should be hassle free and product should be from reputed brand like Godrej, Ozone or equivalent. Handles, nobs etc. should not have any sharp edge/ corner and should be from reputed bran like Godrej, Ozon or equivalent. Including all required ball bearing and other accessories to make the wall unit user friendly. Wardrop rails should be from reputed brand like Hettich, Hafele of matching colour. Quated rate should be inclusive of both the cubical and accesories.

WALL UNIT (for TV, bed side table, pantry etc.): Providing and fixing designed wall unit made out of 6 to 19 mm thick approved quality water proof ply finished all the exposed surface with 1.5 mm thick laminates of approved designed, shade and brand including SS bead of 10 to 12 mm wide to be fixed flush with the final surface and wooden bead of required size where applicable. the design require nice cut (depresion) and projection wich are to be finished with matching coloured lamintes 1.5 mm thick of approved colour , shade and brand. The wooden beads are to be finished with 40: 60 PU polish and complete as per instruction of engineer in charge. (measurement will be taken on flat area : width X height)

RECEPTION COUNTER: All inner surfaces to be finished with off white colour 1.5 mm thick good quality laminates from reputed approved brand fixed with approved adhesive. Exposed edges of boards are to be finished with 6 mm thick timber bead of required width finished with 40: 60 PU polish/ Duco paints (where applicable). The two tier counter top (work station for staff and comfort standing for visitor) surfaces are to be finished with Italian marble of approved quality and shade, 4mm thick veneer finished with 40: 60 PU polish, Duco paint (where applicable). The probable size of the counter is 5.40 M long, 1.20M high. Including necessary slider channels for drawers, handle, nobs, locks etc. from reputed brand like Hafele, Hettic, Godrej etc. Finished and complete in all respect as per the instruction of engineer in charge.

ARCHITRAVE / BEADING: Providing and fixing 1st class timber moulded architrave of size 50x20mm to door and window frames with countersunk wood screw,wooden plugs and applying a coat of wood preservative on unexposed surface etc. With Teak wood/Sissu wood.

BEADING:Providing and fixing 1st class timber moulded beading of size 25mm x 15mm around panel inserts of doors with countersunk wood screws including applying a coat of wood preservative on unexposed surface. With Teak wood/Sissu wood.

LOUVER :Providing 1st class local wood (Hollock/ Bonsum)ventilating louvre in 50mm x 38mm size wooden frame with 150mm x 20mm slate made of 1st class local wood including fitting and fixing with nails and painting with two coats of kiricide oiling complete. With Teak wood/Sissu wood.

MEETING TABLE: Supplying materials and making table on site or at factory as per the approved drawing and specifications. The specifications of materials and construction methodology will be as follows: Top: Making table top with 16 mm thick high pressure interior compact Laminate made out of thermosetting resign treated kraft as core material and design paper as a finish surface with lining on the edges. The border of the top should be double layered to get 32 mm thick as per the approved drawing and design. The material should be flame retardant as per BS-476/97 and EN438-6 with classification of BS1D0 standard property, anti-bacterial and anti-termite property under JIS Z2801:2000. It should have resistance to scratch, fire and weather. For bigger size table, necessary arrangement should be made to assemble/ de-assemble the top. Special care should be taken to get smooth and elegant look and there should not be any sharp corner. Colour and edge lining will be as per the view and instruction of the Engineer –in-charge. (The measurements will be taken on finished size of the top of table and side table, in any case height, depth etc. will not be considered for measurement)

Side and others: The side, supporting frame, drawer, shelve, tray etc. made with premium quality prelaminated board of approved colour and brand of 8 mm to 18 mm thick (where applicable) with all necessary hardware and fittings like drawer channel, lock, nob, handle, lift-up, vertical and horizontal slider etc.(where applicable) of approved manufacturer to complete the table as per the drawings and design. Provision for grommet (table cord wire manager) of approved quality (due approval has to be obtained from the Architect/ Department) is to be kept as per need and utility. All necessary installation (where applicable) of power and telephone sockets, switches, speaker, audio system etc. are included ( socket, switch, speaker & audio system will be measured and paid separately). Finished and complete in all respect as per the instruction of Engineer In Charge. Meeting Table for 6 persons :

Conference Table: Supplying materials and making table on site or at factory as per the approved drawing and specifications. The specifications of materials and construction methodology will be as follows: Top: Making table top with 16 mm thick high pressure interior compact Laminate made out of thermosetting resign treated kraft as core material and design paper as a finish surface with lining on the edges. The border of the top should be double layered to get 32 mm thick as per the approved drawing and design. The material should be flame retardant as per BS-476/97 and EN438-6 with classification of BS1D0 standard property, anti-bacterial and anti-termite property under JIS Z2801:2000. It should have resistance to scratch, fire and weather. For bigger size table, necessary arrangement should be made to assemble/ de-assemble the top. Special care should be taken to get smooth and elegant look and there should not be any sharp corner. Colour and edge lining will be as per the view and instruction of the Engineer –in-charge. (The measurements will be taken on finished size of the top of table and side table, in any case height, depth etc. will not be considered for measurement)

Side and others: The side, supporting frame, drawer, shelve, tray etc. made with premium quality prelaminated board of approved colour and brand of 8 mm to 18 mm thick (where applicable) with all necessary hardware and fittings like drawer channel, lock, nob, handle, lift-up, vertical and horizontal slider etc.(where applicable) of approved manufacturer to complete the table as per the drawings and design. Provision for grommet (table cord wire manager) of approved quality (due approval has to be obtained from the Architect/ Department) is to be kept as per need and utility. All necessary installation (where applicable) of power and telephone sockets, switches, speaker, audio system etc. are included (socket, switch, speaker & audio system will be measured and paid separately). Finished and complete in all respect as per the instruction of Engineer In Charge. Conference Table for 25 persons:

PIN UP BOARD: Supplying and fixing in position High tear-strength Flocked Fabric (Velvet) Surface warp-free, smell-free and corrosion-free pin-up board of reputed brand having market existence of at least five years and good track record framed with heavy anodised aluminium channels and chrome plated corners of 1200mm X 900mm . The board should have high-density Soft Board Core to ensures documents stay securely pinned at all times and resists hole formations even after multiple pinnings. Inclusive of Built-in ABS wall hangers to allow hassle-free mounting of the board in portrait as well as landscape orientation. Complete with all hardware for installation as per the direction of Engineer In Charge. Minimum MRP of the product should not be less than Rs.2,000.00 (Rupees Two thousand) only.

PIN UP BOARD:Supplying and fixing in position High tear-strength Flocked Fabric (Velvet) Surface warp-free, smell-free and corrosion-free pin-up board of reputed brand having market existence of at least five years and good track record framed with heavy anodised aluminium channels and chrome plated corners of 1800mm X 1200mm . The board should have high-density Soft Board Core to ensures documents stay securely pinned at all times and resists hole formations even after multiple pinnings. Inclusive of Built-in ABS wall hangers to allow hassle-free mounting of the board in portrait as well as landscape orientation. Complete with all hardware for installation as per the direction of Engineer In Charge. Minimum MRP of the product should not be less than Rs.2,000.00 (Rupees Two thousand) only.

DUCO PAINT: Providing and applying in 3 or more coats lacquer paint of "DUCO" or equivalent make and approved shade over metallic surfaces / wood and other surfaces after preparing the surface with good quality water proof putty to get proper surfaces, applying necessary coats of primer and finishing with matt / textured finish laquer paint. All complete as per detail drawing, as specified and as directed by Architect / Consultant / Project - In - Charge.

CNC CUTTING WITH GLASS: Providing and fixing milky white good quality glass 6mm thick behind CNC cutting jalli (CNC cutting jalli will be measured and pain separately) with necessary concealed aluminum frame to get an integrated look. Including provision for fixing light fixtures and complete as per instruction of engineer in charge.

WOODEN FLOORING: Providing,fitting and fixing solid wood wooden flooring from reputed brand like Uniproducts (India) Ltd./ Armstrong of thickness 14mm made of pure wood(Engineered Wood) of different types with a top layer of 3mm thick hard wood and Under layer of 2mm thickness made of polythene and foamsheet laid on existing concrete/tiles floor complete as directed and specified.

FOUR SEATER SOFA SET :Supplying premium category sofa made of solid wood combination of ethnic and contemporary style, PVC upholstery in brown shade and prominent stitching lines along with soft foam cushion seats. The armrest and frame in square form finished in cappuccino shade. The sofa set should be designed to optimum use of space and easy to maintain. Including matching centre table made of MDF top and rubber wood understructure finished with cappuccino shade. Load bearing capacity should not be less than 25 kg. Complete in all respect and finished as per instruction of Engineer-in-charge. 1.Single-Seater (2 nos.) : 2.Three-Seater (1 no.) : 3.Centre-table (1 no.): Godrej model : Encardo (3+1+1) with Splenda centre table Featherlite model : 238-1S PEARL (Single Seater Leatherette Sofa - 2 nos.), 238-3S PEARL(Three Seater Leatherette Sofa - 1 no.), 610-FL (Rectangular table - 1 no.) Wipro model : Alysia 1 Seater Leathertte, Alysia 3 Seater Leathertte

SINGLE SEATER SOFA: Supplying and placing In position wooden framed single sitter sofa, S.S leg, leatherette seat cover above high density foam cushion from reputed brand like Godrej, feather light or equivalent. Minimum side of the sofa should not be less than : 715x750x725mm.

THREE SEATER SOFA: Supplying and placing In position wooden framed three sitter sofa, S.S leg, leatherette seat cover above high density foam cushion from reputed brand like Godrej, feather light or equivalent. Minimum side of the sofa should not be less than : 1950x750x725mm.

CORNER ADJUSTING SOFA: LHS Sectiona sofa Supplying and placing In position wooden framed tLHS Sectiona sofa, S.S leg, leatherette seat cover above high density foam cushion from reputed brand like Godrej, feather light or equivalent. Minimum side of the sofa

UTILITY RACK :Supplying materials and making a utility rack on site as per the approved drawing and specifications. The specifications of materials and construction methodology will be as follows: Making rack with 19 mm thick ply board finished with laminate as specified. The material should be flame retardant as per BS-476/97 and EN438-6 with classification of BS1D0 standard property. Finished and complete as per the specifications, drawings and instruction of the Engineer-in-charge.

Conference chair Medium back chair, PU adjustable arm, Synchro Tilt, Gas Lift, Nylon Base, Mesh Back

Round dining table ( 4 seater ) Supplying 4 seater knock down style , 1200 mm dia and 750mm height round dining table , table top made of tempered glass of thickness not less than 12mm with bevelled edge and moulding having with chrome finished legs as shown in the reference image ( Please check the refer image enclosed)

Bath room Mirror: Providing fitting and fixing 716mm Diameter Round Shape Mirror from KOHLER Essential mirror collection of approved soft silhouettes.

CURTAIN: Supplying fitting and fixing of window/ door curtain of approved colour, texture and pattern stitched to the size of the opening including required extension in length and width. Prior approval should be obtained to finalize the design and pattern. The cloth (Material) should be of Polyester having minimum thread Count: 220 and GSM:299 and of normal machine washable in cold water. Including required aluminum based curtain rod suitable for office interior along with necessary accessories for fixing the same in position. Finished and complete in all respect as per the direction of the Engineer In Charge. The basic price of the curtain material should not be less than Rs.1200.00 (Rupees one thousand two hundred) only per meter for 1.20 M wide cloth and for curtain rod basic price should not be less than Rs.300.00 (Rupees three hundred) only per meter.

NET CURTAIN:Supplying fitting and fixing of net curtain of approved colour, texture and pattern stitched to the size of the opening including required extension in length and width. Prior approval should be obtained to finalize the design and pattern. The cloth (Material) should be of Polyester having minimum thread Count: 220 and GSM:299 and of normal machine washable in cold water. Finished and complete in all respect as per the direction of the Engineer In Charge.

AIR CURTAIN: Supplying, installation, testing and commissioning of Air curtain to provide sufficient high velocity pressure air stream across door opening to prevent intermingling of outer and indoor atmosphere air. The product should sleek in design, Modular construction, silent radial flow impellers, easy to installation, M.O.C. MS powder coated/SS/Fiber glass body with ABS plastic grills, aluminum/SS Impellers, Motor aue/gec/match/jai etc. suitable for door of width of 2.00 to 2.40 M. and height of 2.50 M. The air flow velocity should not be less than 12.00 M/ Sec.

MINI FRIDGE: Supplying installation and commissioning of 30 lit. cubical type mini fridge of approved colour from reputed brand like Godrej, Panasonic, Samsung orequivalent.within existing cupboard

LOCKER: Supplying installation testing and commissioning Godrej NX Pro Digital 15L Home Locker Ebony of approved colour.

RFID LOCKING SYSTEM: Supplying installation testing and commissioning of 13.56 MHz, Mifare Technology based Smart RFID card & Fingerprint Reader/terminal for Door Access Control System for 24 room and lift including the software, card readers with or without mortise locking arrangement (for lift only card reader), SS handle (refer Godrej Electronic, Hotel card Lock, ID 20767975988). Complete as per specification in annexure- and complete)

AUDIO AND VISUAL DISPLAY SYSTEM FOR CONFERENCE HALL : Supplying, installation testing and commissioning of conference room audio and visual display system as per the specifications enclosed SPECIFICATION AS PER ANNEXURE - IV)

AUDIO AND VISUAL DISPLAY SYSTEM AT MEETING HALL: Supplying, installation testing and commissioning of conference room audio and visual display system as per the specifications enclosed (SPECIFICATION AS PER ANNEXURE - V)

High Back Officers' Chair Minimum Features : 1.Height adjustable back. 2.Height adjustable arms. 3.Seat depth adjustment. 4.Active bio-synchro mechanism. Equivalent to Godrej model : Marvel High Back Featherlite model : Opus High Back Wipro model : Adapt High Back

Mid Back Chairs for visitors, meeting and other Minimum Features : 1.Height adjustable back. 2.Height adjustable arms. 3.Seat depth adjustment. 4.Active bio-synchro mechanism. Equivalent to Godrej model : Marvel Mid-back Featherlite model : Opus Mid-back Wipro model : Adapt Mid-back

OFFICE TABLE: Supplying factory made office table of minimum size 1800 X 900 X 750 mm top made out of 25mm thick Pre-laminate particle board finished with 2mm edge lipping supported on 25 mm thick Gable ends with necessary MS Brackets. including 18 mm thick PLT Modesty Panel of 450 mm ht, Wire Management Grommet Hole etc.

STORAGE UNIT FOR OFFICE : Supplying and fixing in position storage units/ cabinets/ racks etc. made with premium quality prelaminated board of approved colour and brand of 8 mm to 18 mm thick (where applicable) with all necessary hardware and fittings like drawer channel, lock, nob, handle, lift-up, vertical and horizontal slider etc.(where applicable) of approved manufacturer to complete the storage units/cabinets as per the drawings and design. The side, supporting frame, drawer, shelve, tray etc. should be rigid to resist the required load. The size and shape of the storage unit/cabinet should be as per approved enclosed drawings. All materials should fulfill the norms of IS 2046 (Indian Standard). or equivalent international code. Green Guard Certified product is preferable in any case. Including fixing in position and finished in all respect as per the instructions of Engineer In Charge. (Depth of the storage unit/cabinet may vary in between 450 mm to 600 mm and for measurement in Sqm, length and height of the storage unit/cabinet will be considered)

STUDY TABLE FOR BLOCK A: Supplying and fixinf in position Designer table width not more than 750 mm and length not mor than 1800 mm ( according to the availabilty of space) made out of 6 to 19 mm ply and MDF board finished with 4 mm thick approved coloured 40:60 PU polished veneer. The border of the top should be multilayered to get 50 mm thickness. Necessary wooden bead, finished with 40: 60 PU polish should be used where necessary. A drawer width not less than 450 mm and side shelf below the drawer of equal depth with ply/MDF board palla finished with 40:60 PU polish 4 mm thick veneer. All hardware used for drawer, handle, nob etc. should be SS mat finish from reputed brand like Hettic, Hafele, Godrej or equivalent. Finished and complete as per drawing and design and instruction of engineer in charge.

STUDY TABLE FOR BLOCK B: Supplying and fixing in position study table made with premium quality prelaminated board of approved colour and brand of 8 mm to 18 mm thick (where applicable) with all necessary hardware and fittings like drawer channel, lock, nob, handle, lift-up, vertical and horizontal slider etc.(where applicable) of approved manufacturer to complete the table as per the drawings and design. The side, supporting frame, drawer, shelve, tray etc. should be rigid to resist the required load. The size and shape of the table should not be less than 1200 X 750 mm and 750 mm high. All materials should fulfill the norms of IS 2046 (Indian Standard). or equivalent international code. Green Guard Certified product is preferable in any case. Including fixing in position and finished in all respect as per the instructions of Engineer In Charge. Depth of the drawers should be in between 450 mm to 600 mm all the edges are to be finished with 2mm thick 16 to 19mm wide PVC/paper edge binding of approved quality including necessary synthetic resin hot pressed to edges on binding machine having property of providing uniform and integrated look.

KING SIZE BED FOR BLOCK A: Supplying and fixinf in position King size bed without any head board height not more than 300 mm, without any mattress grip (plain top) made out of 19 mm water proof ply from approved brand. All the visible surfaces are to be finished with 40:60 PU polished 4 mm thick veneer of approved shade. Top of the bed should be projected b at least 150 mm all around. Edges are to be covered with 6 mm thick timber bead of required width finished with 40: 60 PU polish. Including necessary rubber buffer and finished.

QUEEN SIZE BED FOR BLOCK A : Supplying and fixinf in position Queen size bed without any head board height not more than 300 mm, without any mattress grip (plain top) made out of 19 mm water proof ply from approved brand. All the visible surfaces are to be finished with 40:60 PU polished 4 mm thick veneer of approved shade. Top of the bed should be projected b at least 150 mm all around. Edges are to be covered with 6 mm thick timber bead of required width finished with 40: 60 PU polish. Including necessary rubber buffer and finished.

SINGLE BED FOR BLOCK A : Supplying and fixinf in position Single size bed without any head board height not more than 300 mm, without any mattress grip (plain top) made out of 19 mm water proof ply from approved brand. All the visible surfaces are to be finished with 40:60 PU polished 4 mm thick veneer of approved shade. Top of the bed should be projected b at least 150 mm all around. Edges are to be covered with 6 mm thick timber bead of required width finished with 40: 60 PU polish. Including necessary rubber buffer and finished.

KING SIZE GENERAL BED : Supplying and fixinf in position King size bed with head board and side and rear grip for 150 mm thick mattress made out of good quality pre-laminated particle board, ply board of required thickness. Height of the bed should not be less than 350 mm and there should be a head board of at least 450 mm above the mattress. 2mm thick 16 to 19mm wide PVC edge binding tape of approved quality with necessary synthetic resin hot pressed to edges on binding machine. Including necessary MS clamp concealed/ counter sung screw etc. and finished and complete as instructed.

SINGLE BED GENERAL: Supplying and fixinf in position Single size bed with head board and side and rear grip for 150 mm thick mattress made out of good quality pre-laminated particle board, ply board of required thickness. Height of the bed should not be less than 350 mm and there should be a head board of at least 450 mm above the mattress. 2mm thick 16 to 19mm wide PVC edge binding tape of approved quality with necessary synthetic resin hot pressed to edges on binding machine. Including necessary MS clamp concealed/ counter sung screw etc. and finished and complete as instructed.

MATTRESS: Supplying and fixing in position 250mm pocket spirng HD foam based mattress fro reputed brand brand like Kurlon, Sleepwell or equivelent.

MATTRESS: Supplying and fixing in position 150mm pocket spirng HD foam based mattress fro reputed brand brand like Kurlon, Sleepwell or equivelent.

CENTER TABLE: Sofa center table roond and rectangular shape (900 dia or 1200 X 600 mm) Top & Sides made out of 25 mm Thick pre-laminated particle board height not more than 600 mm or as per manufacturer like Godrej, Feather light, Geeken etc. The under structure made out of 50 mm dia MS power coated leg with necessary lever, rubber buffer.

EPBAX: Supplying ,installation, testing & commissioning of Hi-Path 1120 Digital Communication System equipped with the following: 6 P&T Ports - 16 Extension Ports Auto Call Back , Built-in FAX/DID Built in Voice Guided Direct inward Dialling 3 party Conference In-built Caller ID 100% Non- Block ( SIEMENS or equivalent as approved by the Deptt.)

EPBAX:Supplying ,installation, testing & commissioning of Hi-Path 1190 Digital Communication System equipped with the following: 6 P&T Ports - 30 Extension Ports (upgradeable up to 140 extensions) Auto Call Back Built-in FAX/DID 3 party Conference In-built Caller ID Supports PRI / BR Built in Voice Guided Direct inward Dialling 3 party Conference In-built Caller ID 100% Non- Block Supports PRI/BR ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of 8 port Extension Card for 1190 ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of IPM( Integrated Protection Module , ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of Digital Profiset 3030 for one Touch Button & Busy Extension Indicator for Reception & Boss, ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of Open Stage 20T Digital Phone ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of Open Stage 40T Digital Phone ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of Dedicated EPABX Earthing for trouble free operation ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of UROSET 2005 Analog Hand set ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of Constant Voltage Transformer 500 VA ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning HVAC, AIR CONDITIONING (SPECIFICATION AS PER ANEXURE - VI)

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

Supplying and stacking at site. : Stone screening 11.2 mm nominal size (Type B)

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. : 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

GAEDEN CHAIR: Supplying and Installation of Garden Seating of minimum overall dimension of 1550mm x 850mm and height 600mm (fixing height 400-450mm) made out of MS structure (pipe,flat,etc where applicable) welded and finished smooth. The finishing should be of weather proof powder coating of pipe end should be of weather proof powder coating of approved colour. All the joints, hole, opening of pipe end should be water proof. The successful bidder need to get approval of physical sample from the authority before finalization of the bench. The rate is inclusive of fixing the chair in position including civil works.

ANIL DAS CONSTRUCTION PVT LTD