CECHZ/PAT/T-04/2021-22 ADDITION ALTERATION AND REHABILITATION OF OFFICERS JCOS ORS MD ACCN AT PATIALA MIL STATION

Amount

ITEM NO. 1 : Taking down Cement plaster or cement lime plaster on brick or stone walls including raking out joints hacking for key & scrubbing down with water etc removing the debris, waste material obtained from demolition/dimantling out side the peripheri of defence Land (MOD) complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 2 : BLANK

ITEM NO. 3 : Rendering 15 mm thick in cement mortar 1:4, on brick or concrete surfaces mixed with water proofing compound, including finishing the surfaces even and fair without using extra cement, complete all as specified and directed by Engineer-in-Charge. NOTE: Water proofing compound shall be measured and paid separately.

ITEM NO. 4 :Rendering 10 mm thick in cement mortar 1:6 on fair or uneven faces of brick work or concrete surfaces including finishing the surfaces even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 5 : Supply only liquid water proofing compound ISI marked complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 6 : Rendering 5 mm thick in cement mortar 1:3 on fair faces of concrete (ceiling ) surfaces, finishing the surfaces even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 7 : BLANK

ITEM No 8 : Description All as per serial item No.6 here-in-before but over and including dubbing out average 10mm thick in cement mortor (1:4) on irregular surface of soffits of slabs/Chajja/ Sunshades etc complete all as specified and directed by Engineer-in-Charge.

ITEM No 9 : Preparation of newly plastered internal surfaces of Walls by applying white cement based wall care putty minimum thickness 1.50 mm after preparation with emery paper or sand paper to get smooth surface to receive painting complete all as specified and directed by Engineer-in-Charge.

ITEM No 10 : Preparation of newly plastered internal surfaces of Ceilings by applying white cement based wall care putty minimum thickness 1.50 mm after praparation with emery paper or sand paper to get smooth surface to receive painting complete all as specified and directed by Engineer-in-Charge.

ITEM NO.11 : Applying two coats of oil bound distamper white or tinted, over and including a coat of primer including preparation of newly plastered Surfaces of wall complete all specified and directed by Engineer-in-Charge.

ITEM NO.12 : Preparation of Plastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed by Engineer-in-Charge. (Note:- Measurment purpose only flat surface shall be measured)

ITEM NO.13 : Preparation of old wall surface brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and effloresent salts, trading oils, greasy spots and applying 1.5 mm thick white cement based wall care putty to get smooth surface to receive painting complete all as specified and directed by Engineer-in-Charge.

ITEM NO.14 : Complete removal of existing treatment and applying two coats of cement base paint on walls including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

ITEM NO.15 : Complete removal of existing treatment and applying two coats of oil bound distemper on walls over a coat primer including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

ITEM NO.16 : Preparation of plastered or unplastered new surfaces of ceiling and applying three coats of white wash including Preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

ITEM NO.17 : Complete removal of existing treatment of ceiling and applying three coats of white wash including prepartion of Surfaces complete all as spesified and directed by Engineer-in-Charge.

ITEM NO.18 : Demolition of brick work built in cement mortar including all quions arches, pillar or any other descrption etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.19 : Brick work with sub class 'B' bricks, class designation 100, old size bricks straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

ITEM NO.20 : Demolition of cement concrete (reinforced) and (reinforcement cut as required to facilitate demolition) as in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work complete all as specified and directed by Engineer-in-Charge.

ITEM NO.21 : Use & waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings , slab over manholes similar work; not exceeding 200mm thick (Horizontal or sloping) (rough finished flat surfaces of concrete), complete all as specified and directed by Engineer-in-Charge.

ITEM NO.22 : Use and waste of form work to chullah hoods, chajjas, troughs and similar items including edges and similar work for fair finish surfaces complete all as specified and directed by Engineer-in-Charge.

ITEM NO.23 : Use & waste of Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide (rough finished surfaces of concrete), complete all as specified and directed by Engineer-in-Charge.

ITEM NO.24 : Reinforced Cement Concrete of grade M-25 (design mix) using 20mm graded mechanically crushed stone aggregate as in chajjas and the like complete all as specified and directed by Engineer-in-Charge. NOTE: Reinforcement will be measured and paid for separately.

ITEM NO.25 : TMT steel bars 10mm dia and over, of grade Fe-500D cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

ITEM NO.26 : Use and waste of Formwork to sides of RCC/PCC bands in walls complete all as specified and directed by Engineer-in-Charge.

ITEM NO.27 : RCC M-25 (using 20 graded mechanically crushed stone aggregate) as in roof beams, cantilevers, bressummers, lintel beams over 1.5 m span, waste slabs, steps, railings, parapets etc complete all as specified and directed by Engineer-in-Charge. NOTE: Reinforcement will be measured and paid for separately.

ITEM NO.28 : Mild steel TMT bars 8mm dia and over as in stirrups/spacers and binders cut to length, bent to shape required including cranking, bending spirally for hooping for column hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

ITEM NO.29 : Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish out side the premises of defence Land complete all as specified and directed by Engineer-in-Charge.

ITEM NO.30 : Demolition of Cement Concrete Unreinforced as in Ground Floors & paving n. exc. 15cm thick (above or below G.L.) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.31 : Cement concrete (1:5:10) type E-2,using 40 mm graded mechanically crushed stone aggregate 75 mm thick as in sub base of floors complete all as specified and directed by Engineer-in-Charge.

ITEM NO.32 : Cement concrete (1:2:4) type B-0,using 12.5 mm graded machanically crushed stone aggregate 25 mm thick as in sub base of floors and pavings etc. complete all as specified and directed by Engineer-in-Charge.

ITEM NO.33 : Non - skid coloured Ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry over & including 15 mm thick cement mortar (1:4) screed bed and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.

ITEM NO.34 : Glazed ceramic coloured printed/digital tiles 7mm- 8 mm thick (square/ rectangular) area of each tile exceeding 0.12 sqm but not exceeding 0.18 sqm, on vertical surface such as skirting , dado etc. over & including 10 mm thick rendering in cement mortar 1:4 thick set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles complete all as specified and directed by Engineer-in-Charge.

ITEM NO.36 : Vitrified ceramic tiles coloured,printed/digital 8 to 9mm thick(Square/rectangular) polished, area of each tile exceeding 0.18sqm & not exceeding 0.36 Sqm, in skirting/dado etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of the tiles laid over and including 10mm thick rendering in cement mortar (1:3) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.37 : Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc of any description or thickness, laid, bedded and pointed in any mortar complete all as specified and directed by Engineer-in-Charge.

ITEM NO.38 : Machine cut Kota stone slab flooring 18-20 mm thick, for staircase step,single piece not less than 1.20 meter of length laid over & including 20 mm thick (average thickness)screed bedding layer in cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete, including provn of two Nos 3x3mm grooves at tread of each step complete all as specified and directed by Engineer-in-Charge.

ITEM NO.39 : Machine Cut Kota stone slab 18-20 mm thick on vertical surfaces like riser of steps, single piece not less than 1.20 meter of length as in skirting, over & including 10 mm thick (average thickness)screed bedding layer in cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (Mirror finish), complete all as specified and directed by Engineer-in-Charge.

ITEM NO.40 : Baroda green marble, 15-18 mm thick, (table rubbed and polished) machine cut, laid over & including 15 mm thick (average thickness) bedding in cement mortar (1:3) jointed with grey cement slurry & pointed with grout of matching shade including rubbing and polishing (Granite finish), over cooking platform shelives, RCC Counters, window cell and similar situation complete all as specified and directed by Engineer-in-Charge.

ITEM NO.41 : Rounding to edges ( both side edges ) of stone slabs (of any description) , such as in steps, cooking platform, and other similar situations including rubbing and polishing (mirror finish), complete all as specified and directed by Engineer-in-Charge.

ITEM NO.42 : 75mm thick PCC (1:3:6) type C-2 using 40mm graded mechanially crushed stone agg as in plinth protection finished even & smooth without using extra cement including forming and filing of construction jonits complete all as specified and directed by Engineer-in-Charge.

ITEM NO.43 : Taking down chowkaths or frames n.exc 1.5 sqm (without taking off shutter from the frame) each and removing from the site including dismantling brick work for hold fasts complete all as specified and directed by Engineer-in-Charge.

ITEM NO.44 : Taking down chowkaths or frames Exc 1.5 sqm but n.exc 4 sqm (without taking off shutter from the frame) each and removing from the site including dismantling brick work for hold fasts etc complete all as specified and directed by Engineer-in-Charge.

ITEM NO.45 : Factory made Pressed steel frames, confirming to IS, having profile 125 x 60 mm made out of 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and fixing only 125 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge. Note: The Mild Steel butt hinges will be measured and paid separately as supply only under relevant item.

ITEM NO.46 : Factory made Pressed steel frames, confirming to IS, having profile 105 x 60 mm made out of 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and fixing only 125 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge. Note: The Mild Steel butt hinges will be measured and paid separately as supply only under relevant item.

ITEM NO.47 : 35mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed by Engineer-in-Charge.

ITEM NO.48 : 35 mm thick factory made glazed & Skeleton shutters of 2nd class Hard Wood open rebated & prepared to receive glass or gauze etc without sash bars open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc size of stiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I (2010) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.49 : Solid PVC door frames of size 50mm x 47 mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube, and edges will be painted to match with printed sheet, supply & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

ITEM NO.50 :Factory Made Solid PVC Moulded flush Door Shutter, 28 to 30mm thick(stiles), with 2, 4, or 6 raised panel design with light colour matching to frame printed 4mm thick Moulded PVC Sheet on the front face & 4mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

ITEM NO.51 : Powder coated (Minimum thickness of powder coating 50 micron ) Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engineer-in-Charge.

ITEM NO.52 : Aluminium window (Casement & sliding) and ventilator shutters with 50 micron powder coating double shutters made and to be fixed with EPDM gasket to render the glazing, air and water tight etc. and aluminium beeds in inner shutters complete fixed in all respect as specified & directed by Enginner-in-Charge. Note :- EPDM gasket shall be measured as supply only separately

ITEM NO.53 : BLANK

ITEM NO.54 : Aluminium 50 micron powder coated grill, opening size 101.6 X 63.5 mm (4"X2½") and of weight not less than 1.345 Kg/sq.m complete fixed in position in windows in all respect complete all as specified and directed by Engineer-in-Charge.

ITEM NO.55 : Stainless steel butt hinges 150 mm long medium weight and fixed complete all as specified and directed by Engineer-in-Charge.

ITEM NO.56 : Aluminium alloy anodised extruded fabricated type handle 150mm long complete all as specified and directed by Engineer-in-Charge.

ITEM NO.57 : Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) 250 mm long fixing clips of sheet cast or and fixing with bolts extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed by Engineer-in-Charge.

ITEM NO.58 : Mild steel sliding door bolt 200 mm long plate type stove enamelled black with bright bolt not less than 12mm dia with & including a minimun of 6 bolt nuts four an bolt plate and two on staple plate fixed complete all as specified & directed by Engineer-in-Charge.

ITEM NO.59 : Aluminium alloy, anodised, barrel tower bolt (bolt type) 200 mm long of extruded section or cast aluminium alloy and fixed complete all as specified and directed by Engineer-in-Charge.

ITEM NO.60 : Mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed by Engineer-in-Charge.

ITEM NO.61 : Plain cement concrete (1:3:6) type C-0,using 12.5 mm graded mechanically crushed stone aggregate as in back filling of pressed steel frame /hold fast blocks etc and similar complete all as specified and directed by Engineer-in-Charge.

ITEM NO.62 : Dismantling of stucturel steel work as in door chowkats, shutters guard bars and similar items but excluding framed truss complete all as specified and directed by Engineer-in-Charge.

ITEM NO.63 : Mild steel framed work of Fe-290 (Gde E-165) quality as in Doors or gates made of angle and other sections with gusset plates rails braces etc. Complete including drilling and welding for fixing of steel sheeting or other covering of doors, gates etc to be prepared for hanging or sliding with and including drilling and welding for fixing of steel sheeting or other covering of doors gates etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fitting( Exclusive of steel sheeting or other covering running rails and guides) and handing also fastening and fixing, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.64 : Mild Steel Framed work such as Guard Bar/grill welded to window frame or fixed independantly, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified & directed by Engineer-in-Charge.

ITEM NO.65 : Steel work in tubular truss including special shaped washer etc complete using ERW or induction but welded tubes conforming to IS 1161 - 1998 grade YST - 240 complete all as specified and directed by Engineer-in-Charge.

TEM NO.66 : Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed with self tapping screws as recommended by manufacturer complete all as specified and directed by Engineer-in-Charge.

TEM NO.67 : Solid PVC wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on & including PVC frame grid of solid PVC fillets 5 mm thick and 38 mm wide as per specification and drawings complete all as specified and directed by Engineer-in-Charge.

ITEM NO.68 : Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

ITEM NO.69 : Preparation of new or previously untreated wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

ITEM NO.70 : Two coats of synthetic enamel paint over newly primed steel and iron surfaces of any descrption, not otherwise described, over 10 cm in width or girth, including preparation of primed surfaces complete all as specified and directed by Engineer-in-Charge.

ITEM NO.71 : 300 mm MS ordinary rat tail rod pattern springs including roller and roller plate fixed to wooden chowkhats or welded to angle iron door frames complete all as specified and directed by Engineer-in-Charge.

ITEM NO.72 : Supply only 100 mm long cold rolled mild steel butt hinges medium weight complete all as specified and directed by Engineer-in-Charge.

ITEM NO.73 : S&F in repair stainless steel tubing of 25 mm dia min. 1.0 mm wall thickness as in curtain rod complete including necessary stainless steel brackets and finials fancy type, stops fixed with stainless steel screws etc all as specified & directed by Engineer-in-Charge.

ITEM NO.74 : Dismantling wooden boarding of any description, fixed in any position with nails as in shelves of cup board and pelmets of any description complete all as specified and directed by Engineer-in-Charge.

ITEM NO.75 : LEAD FREE PVC Celuka ply 18 mm thick ( minimum density 600 Kg/Cum) of both side plain white colour , fixed with stainless steel screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed by Engineer-in-Charge..

ITEM NO.76 : LEAD FREE PVC Celuka ply 18 mm thick (minimum density 600 Kg/Cum) of single side rigid lamination of approved colour and other side plain white colour fixed with stainless steel screws and solvent cement/ adhesive to make kitchen cabinet shutters and shelves complete as per manufacturer’s specifications complete all as specified and directed by Engineer-in-Charge.

ITEM NO.77 : 12 mm thick with min density 600 Kg/cum LEAD FREE PVC Celuka ply of fixed with Stainless steel screws and solvent cement/ adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per manufacturer’s specifications complete all as specified and directed by Engineer-in-Charge.

ITEM NO.78 : Auto closing hinges of size 35 mm of 0 crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in position all as specified. complete all as specified and directed by Engineer-in-Charge.

ITEM NO.79 : Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity minimum 50 kgs complete all as specified and directed by Engineer-in-Charge.

ITEM NO.80 : D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 150mm long matt finished complete fixed in position all as specified and directed by Engineer-in-Charge.

ITEM NO. 81 : Stainless Steel 304 grade wire Basket (average weight 2.5 to 4 Kg. per basket) of pull out type like plain/cup&saucer/bottle/multi purpose/2-3 shelf baskets etc. for kitchens of required size fixed in position complete all as specified and directed by Engineer-in-Charge.

ITEM NO.82 : Stainless Steel 304 grade Basket Cutlery of size 370X485mm premium quality fixed in position complete all as specified and directed by Engineer-in-Charge.

ITEM NO.83 : Built in cup boards with pressed steel frame of size 75x45x1.25mm thick and shutter of 1.00 mm thick MS sheet including spray painting 2 coats over a coat of red-oxide primer on steel shurfaces all around all shown on drawing No TD-178 sheet 2/3 to 3/3 dated 12 May 2001 (overall external size of cup board shutter incl frame shall be taken into consideration for the pupose of measurement) including One No hanging rod of CP steel 20mm bore with brackets & two Nos peg set of three pegs each fixed inside the shutter complete fixed in repairs i.e, including taking down and removal of old unserviceable wooden or steel built-in-cupboards incl frame from site all as specified and directed by Engineer-incharge.

ITEM NO.84 : Taking down of Eaves gutter/rain water pipe( AC rain water pipe /SWG pipe line of any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning for refixing or removal from site (measured overall as fixed along the centre line including fitting and accessories) complete all as specified and directed by Engineer-in-Charge.

ITEM NO.85 : Taking up or down steel tubing and connections of 15mm bore in pipe, including removal from site complete all as specified and directed by Engineer-in-Charge.

ITEM NO.86 : Taking up or down steel tubing and connections of 20mm bore in pipe, including removal from site complete all as specified and directed by Engineer-in-Charge.

ITEM NO.87 : Steel water tubing, galvanised, medium grade, ISI marked, 15 mm bore with and including all fittings , cutting, threading and fixed to walls and ceilings or laid in floors including cutting chases and pinning in including making good the surface to match the extisting one, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.88 : Steel water tubing, galvanised, medium grade, ISI marked, 20 mm bore with and including all fittings , cutting, threading and fixed to walls and ceilings or laid in floors including cutting chases and pinning in including making good the surface to match the extisting one, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.89 : Vitreous china wash down water closet pan (Pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), (Fixed in repairs) P or S trap, including taking down old unserviceable existing one complete all as specified and directed by Engineer-in-Charge.

ITEM NO.90 : PVC water closet seat cover , white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed by Engineer-in-Charge.

ITEM NO.91 : Vitreous China squatting pan of “Orissa Pattern” of size 580x440mm, Fixed in repairs white with integral footrest including taking down old unserviceable existing one complete all as specified and directed by Engineer-in-Charge. Note : The quoted rate shall include provision of "P" Cast Iron trap complete all as specified and directed by Engineer-in-Charge.

ITEM NO.92 : 10 ltr capacity PVC valveless, syphonic action dual flush type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, 32 mm dia flush pipe including taking down old unserviceable existing one complete all as specified and directed by Engineer-in-Charge.

ITEM NO.93 : Health faucet (ABS Body) with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and directed by Engineer-in-Charge.

ITEM NO.94 : PTMT jet spray with 1.00 metre PVC tube , (suitable for European seat) including taking down old unserviceable existing one complete all as specified and directed by Engineer-in-Charge.

ITEM NO.95 : CP toilet paper holder with flap model including taking down old unserviceable existing one complete all as specified and directed by Engineer-in-Charge.

ITEM NO.96 : Vitreous china wash hand basin white flat back of sizes as mentioned in catalogue Nos of the manufacturers given here in after Fixed in Repairs including CI brackets , chromium plated waste coupling, waste pipe etc., (incl all waste fittings) including taking down old unserviceable existing one complete all as specified and directed by Engineer-in-Charge.

ITEM NO.97 :WHB Mixer valve for mixing hot and cold water of Brass Chromium Plated screwed down for 15mm dia iron pipe including taking down complete all as specified and directed by Engineer-in-Charge. Note: The quoted rate shall include the long braided hoses 450mm long for connection to mixer complete.

ITEM NO.98 : 15 mm fancy type chromium plated bib tap of long body with flange cast copper alloy with crutch or butterfly handles screwed down high pressure suitable for 15mm bore pipe or union including taking down old unserviceable existing onecomplete all as specified and directed by Engineer-in-Charge.

ITEM NO.99 :Stainless steel grating doom openable 100mm sq size (Minimum Weight 25 grams) with/without hole including fixing with white cement including taking down old unserviceable existing one complete all as specified and directed by Engineer-in-Charge.

ITEM NO.100: Angle stop valve 15mm bore cast copper alloy chromium plated fancy type high pressure screwed for iron pipe and fixed, including taking down old unservicable existing one complete all as specified and directed by Engineer-in-Charge.

ITEM NO.101 : Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated with long shank and cup (Concealed type) including taking down old unserviceable existing one complete all as specified and directed by Engineer-in-Charge.

ITEM NO.102 : Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 20mm bore, fancy type, chromium plated with long shank and cup (Concealed type)including taking down old unserviceable existing one complete all as specified and directed by Engineer-in-Charge.

ITEM NO.103 : Fancy type shower rose 125mm dia size of Rim and 30cm long Chromium Plated brass pipe with swiwel joint including fixing to steel pipe or union including taking down old unserviceable existing one complete all as specified and directed by Engineer-in-Charge. .

ITEM NO.104 : Sheet glass shelf assembly consisting of 8mm thick glass shelf 300 x 300mm as in corners wide with bevelled edges/hatching of edges fixed with stainless steel 'D' bracket with railing including taking down old unserviceable existing one complete all as specified and directed by Engineer-in-Charge.

ITEM NO.105 : Sheet glass shelf assembly consisting of 5.5 mm th sheet glass shelf 12 cm wide with chromium plated guard and railing 60 cm long including taking down old unserviceable existing one complete all as specified and directed by Engineer-in-Charge.

ITEM NO.106: Soap dish, chromimim plated fixed to plugs with chromium plated brass screws, including taking down old unserviceable existing one complete all as specified and directed by Engineer-in-Charge.

ITEM NO.107 : Brass chromium plated, tubular towel rail, 20mm dia, 60cm long between flanges including taking down old unserviceable existing one complete all as specified and directed by Engineer-in-Charge.

ITEM NO.108 : PVC connections 15mm size with PTMT nuts of length 450mm including taking down old unserviceable existing one complete all as specified and directed by Engineer-in-Charge.

ITEM NO.109 :Sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste pipe including bedding in cement mortar to dwarf wall or cantilever brackets and connecting union to pipe overall size 915x460mm, bowl size 410x 330x160mm including all fittings ie CP waste coupling, waste pipe including taking down old unserviceable existing one complete all as specified and directed by Engineer-in-Charge.

ITEM NO.111 : PVC cabinet with looking mirror of size 350 x 450mm complete all as specified and directed by Engineer-in-Charge.

ITEM NO.112 : CI floor traps with grating complete 100mm bore outlet including jointing to waste pipe fixed in cement concrete 1:2:4 type B-1 complete all as specified and directed by Engineer-in-Charge. Note : The quoted rate shall include embedding the floor trap in PCC block of size 300x300x250 mm block of PCC 1:2:4 type B-2, complete all as specified and directed by Engineer-in-Charge. .

ITEM NO.113 : 110mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, complete all as specified and directed by Engineer-in-Charge.

ITEM NO.114 : Descripition all as per srl.item No.112 here-m-before but CI floor trap 75mm bore.

ITEM NO.115 : S & F in repairs CI 110mm size junction single, (Single T), equal or unequal complete all as specified and directed by Engineer-in-Charge.

ITEM NO.116 : S&F in repairs PVC(SWR) bends, for 110mm bore pipes, in cement mortor access doors, all as specified and directed by Engineer-in-Charge.

ITEM NO.117 : Salt-glazed stone ware gully traps, 150x 150 square or round mouthed, type "p" setting and jointing to drains in cement mortar 1:1 complete all as specified and directed by Engineer-in-Charge.

ITEM NO.118 : Dismantling old unserviceable cement concrete/PVC water tanks of capacity exc 250 ltrs & n.exc 500 Ltrs including supplying & fixing of PVC water storage tank 500 ltr capacity HDPE triple layered ,white colour cylindrical type fixed and hoisted in position on roof at any height complete with inlet/outlet of 20 mm GI Pipe connection incl locking arrangement, including supplying & fixing of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 200 mm - 210 gms ) complete all as specified and directed by Engineer-in-Charge. Note : (i) Inlet, outlet & wash out pipe will be measured paid for separately. (ii) The quoted rate is inclusive of minimum one union each on inlet and outlet of water tank as per size of pipe shall be provided.

ITEM NO.119 : Cast iron sand cast soil waste & vent pipe in any length with or without ears with cement joints fixed to walls 100 mm bore including stack clamps, nuts bolts etc. and making necessary connections, supplied & fixed in repairs complete all as specified and directed by Engineer in Charge.

ITEM NO.120 : Cast iron sand cast soil waste & vent pipe in any length with or without ears with cement joints fixed to walls 75mm bore in and including stack clamps, nuts bolts etc. and making necessary connections, supplied & fixed in repairs complete all as specified and directed by Engineer in Charge.

ITEM NO.121 : Cast iron sand cast soil waste & vent pipe 100mm bore in any length with or without ears with cement joints laid in trenches or in floors supplied & fixed in repairs complete all as specified and directed by Engineer in Charge.

ITEM NO.122 : Cast iron sand cast soil waste & vent pipe 75mm bore in any length with or without ears with cement joints laid in trenches or in floors supplied & fixed in repairs complete all as specified and directed by Engineer in Charge.

ITEM NO.123 : CI bends 100mm bore pipes(any radius) diminishing pieces or tapers (larger bore measured) without oval access door supplied & fixed in repairs complete all as specified and directed by Engineer-in-Charge.

ITEM NO.124 :CI bends 75mm bore pipes (any radius) diminishing pieces or tapers (larger bore measured) without oval access door supplied & fixed in repairs complete all as specified and directed by Engineer-in-Charge.

ITEM NO.125 : CI bend 75mm bore pipes (any radius) with oval access door of 75 mm bore fixed in repair complete all as specified and directed by Engineer-in-Charge.

ITEM NO.126 : CI cowl 100 mm dia complete all as specified and directed by Engineer-in-Charge.

ITEM NO.127 : Dismantling & removal brick or terracing tiles of single layers on roofs including cleaning of bricks/tiles including stacking for measurement and removal from site.complete all as specified and directed by Engineer-in-Charge.

ITEM NO.128 : Wire brushing and cleaning the top surfaces of tiles, lime terracing or cement concrete, roof surfaces etc. with water including flashings and junction of parapets etc. complete all as specified and directed by Engineer-in-Charge.

ITEM NO.129 : Demolition of mud in roof any thickness (whether full thickness removed or part thereof ) including plastering, leaping and removal from site complete all as specified and directed by Engineer-in-Charge.

ITEM NO.130 : APP polymeric water proofing membrane minimum 3 mm thick and weighting not less than 3.6 Kg/Sqm black finish reinforced with non-woven polyster matt wt not less than 150 gms/Sqm with thermo fusable finish laid over compatible bitumen primer at the rate of 0.40 Ltr/Sqm torching over laps with a propane or abutan gas torch with over lap of 75 mm at the side and 100 mm at the ends and sealing including applying a coat of cold emulsion bituminious primer all as per manufacturers instructions including preparation of surface complete all as specified and directed by Engineer-in-Chief. (ii) The water proofing treatment will be got carried out by the manufactarers or their authorised applicators duly approved by the manufacturer.

ITEM NO.131 : Plain Cement concrete 1:2:4 type B-1 using 20mm mechanically graded crushed stone aggregate as in padding to roof to maintain the required slope padding minimum 30 mm thick at end and finished the surface even and smooth without using extra cement over & including a layer of neat cement slurry @3Kg /sqm complete all as specified and directed by Engineer-in-Charge.

ITEM NO.132 : Precast PCC plain factory made tiles, ISI marked, 22 mm thick, of size 250 mm x 250 mm, machine pressed and cut polished and set jointed and pointed in neat cement slurry and fabricated using grey cement & no pigments. over and including 15 mm thick cement mortar (1:3) bedding and joints grouted flush in cement mortar (1:3) mixed with integral liquid water proofing compound over roof surfaces complete all as specified and directed by Engineer-in-Charge.

ITEM NO.133 : Plain cement concrete 1:2:4 type B-0 using 12.5mm graded mechanically crushed stone aggregate as in roof kerbs or mud stops and benching, rounded or chamfered on edges , coving shall be 150 mm in radius mixed with acrylic based polymer water proofing compound complete all as specified and directed by Engineer-in-Charge. Note : WPC shall be paid separately.

ITEM NO.134 Surface excavation exc 30cm deep and averaging 15cm deep in soft/loose soil & getting out including clearing all grass vegetation, saplings, shrubs, brush woods under growth roots and trees, complete all as specified and as directed Engineer-in-Charge.

ITEM NO.135 Removing excavated soil exc 1.50km but n exc 5km and depositing where directed by Engr-in-Charge

ITEM NO.136 100mm thick cement concrete 1:4:8 type D2 (40 mm graded mechanically crushed stone aggregate) as in sub base complete all as specified and as directed Engineer-in-Charge.

ITEM NO.137 60 mm thick coloured precast concrete interlocking paver block rubber moulded any shape and size confirming to IS 15658-2006 M-35 grade with grey cement and pigment to match complete all as specified as directed Engineer-in-Charge.

ITEM NO.138 Sand filling under floor or in foundations including watering and consolidation complete all as specified as directed Engineer-in-Charge.

ITEM NO.139 Providing cement concrete 1:2:4 type B-1 using 20 mm graded mechanically crushed stone aggregate as in copings, slightly, rounded or chamfered angles Including necessary from work complete all as specified as directed Engineer-in-Charge.

ITEM NO.140 Excavation in trenches in soft/loose soil not exceeding 1.50 Mtr wide and not exceeding 1.50 Mtr in depth and getting out in soft/loose soil complete all as specified and directed Engineer-in-Charge

ITEM NO.141 description All as per Serial items No. 140 herein before but exceeding 1.5 Mtr and not exceeding 3.00 Mtr depth

ITEM NO.142 Brick work using Sub Class "B" bricks class designation 100 straight or curved on plan not exceeding 6 Mtr means radius built in CM 1:4 complete all specified and directed by Engineer-in-Charge

ITEM NO.143 Providing, precast cement concrete (1:2:4) type B-1 using 20mm graded machnically crushed stone agg as in window or door cills, lintels, bressummers, steps, quoin blocks (for use with masonry), string courses, copings, kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, anchorage blocks, bonders (for stone walling), corbels, brackets, etc.(of any section indicated), with plain fair faces, including chamfers weatherings, throating etc. complete all specified and directed by Engineer-in-Charge

ITEM NO.144 Reinforced concrete pipes of 150mm dia, class NP-2, laid and jointed complete with collars and jointed complete in cement mortar (1:1) complete all as specified and directed by Engr-in-charge.

ITEM NO.145 PCC (1:4:8) type D-2 (using 40mm graded mechanically crushed stone aggregate) as in foundation of manholes complete all as specified and directed by Engr-in-charge.

ITEM NO.146 Cement concrete 1:2:4 type B-0 (using 12.5 mm graded aggregate) in coping, haunching, benching of drains including necessary form work complete all as specified and directed by Engr-in-charge.

ITEM NO.147 Extra for forming fair finished drain or channel 30 cm to 45 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed by Engr-in-charge.

ITEM NO.148 Add or deduct to Srl item No 147 here-in-before for each 25 mm girth or part there of over or under 30 cm girth complete all as specified and directed by Engr-in-charge.

ITEM NO.149 Cutting into existing manholes for connecting new drains of 150mm diamaking good to pipe and rendering cutting out existing benching for and formingbranch channel (1/2 round or 3/4section) in cement concrete 1:2:4 mix type B-1smooth finished and reforming benching as required of 150mm dia of pipe complete all as specified and directed by Engr-in-charge.

ITEM NO.150 RCC (1:2:4) type B-1 using 20mm graded mechanically crushed stone aggregate as in precast slabs for covers of manholes and set in CM 1:6 including necessary from work hand placing of manhole cover on mamholes complete all as specified and directed by Engineer-in-Charge

ITEM NO.151 TMT bars 8mm dia and over cut to length bent to shape required incl cranking bending, spirally , hooking ends and binding with mild steel wire not less than 0.9mm dia (annealed) complete all as specified and as directed by Engineer-in-Charge. (Note : The payment shall be made only after placing of cover on manholes)

ITEM NO.152 Returning and filling including spreading, levelling, water and well ramming in layers not exceeding 25cm thick complete all as specified and directed Engr-in-charge

ITEM NO. 153 : BLANK

ITEM NO.154 Removal of excavated material n. exc 50 M and depositing where directed at a level not exc 1.5 M above the starting point complete all as specified and directed Engr-in-charge

ITEM NO.155: Use and waste of timbering as planking and strutting for excavations exc 1.50m deep and n exc 3.00 m deep in shafts, wells, cesspits, manholes and pier holes as may be necessary and fixing and removal complete all as specified and directed Engr-in-charge

ITEM NO.156 : Floor door stopper of 150mm aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor all as specified and directed by Engr-in-Charge. complete all as specified and directed.

ITEM NO.157 : Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed by Engineer-in-charge.

ITEM NO. 158 : Removing building material exc. 250 m but n exc. 500 m and depositing where directed all as specified and directed by Engr-in-Charge.

ITEM No 159 : Applying 02 (Two) coats of Aluminum painting over and including a coat of primer over APP surfaces by using roller/brush as per manufacture's instructions complete all as specified and as directed by Enginner- in -Charge.

ITEM NO. 160 : Float glass 5.00 mm thick in door/window/ventilator etc. complete all as specified and as directed by Engineer-in-charge.

ITEM NO. 161 : Frosted/smoked glass 5.00 mm thick in fornt shutters complete all as specified and as directed by Engineer-in-charge.

ITEM NO. 162 : Stainless steel but hinges 100 mm long medium weight and fixed with screws complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 163 : Powder coated Aluminium Tower Bolt 150 mm Long complete all as specified and as directed by Engineer-in-charge.

ITEM NO. 164 : Powder Coated Aluminium "American type" Handies size 200 mm complete all as specified and as directed by Engineer-in-charge.

ITEM NO. 165 : Powder Coated Aluminium "American type" Handies size 150 mm complete all as specified and as directed by Engineer-in-charge.

ITEM NO. 166 : Powder Coated hook and eye 01 Nos per leaf (peg stay)complete all as specified and as directed by Engineer-in-charge.

ITEM NO. 167 : Supply only EPDM gasket for shutters etc complete all as specified and directed by Engineer-in-charge.

ITEM NO. 168 : Forming Contraction (Dummy) joints 30 mm deep x 10 mm wide, filled with Grade 'A' sealing compound complete all as specified & directed by Engineer-in-charge.

ITEM NO.169 : Taking down rolling shutters exc 2 Sqm each complete all as specified and directed. By Engineer-in-charge.

ITEM NO.170 : BLANK

ITEM NO.171 : Taking down carefully existing points wiring on surface conduit/concealed conduit for light/ fan/socket /power/ bell from wall & roof along with fitting and fixtures such as switches, sockets, ceiling roses, batten holders, unserviceable light fittings, piece of wires,gutties, conduit, wooden boards etc and making good the disturbed portion of walls, ceiling etc all as specified and directed Engr-in-charge.

ITEM NO.172 : Point wiring with 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper conductor for one light/fan and including PVC rigid concealed conduit medium grade 19/20 mm dia to be terminated in pressed steel cadmium plated terminal box not less than 1.6mm thick for mounting Modular type switches, sockets, fan regulators etc with modular top cover including 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper earth continuity conductor controlled by one switch and/or one regulator complete including repairing the surfaces in CM 1:3 and finishing the surface as per existing treatment all as specified and directed complete all as specified and as directed by Engineer-in-charge.(Switches and regulators shall be measured and paid for separately.) Note II-( Wiring shall be done as per colour code in IS for phase, neutral and earth). Note-III- The cost of Modular cover plate and metal flush boxes is deemed to be included in the unit rate quoted for this item) Note-IV-Cost of Eye/bottle thimbles used for connection in switches/sockets & MCBs in DBs shall deemed to be included in the unit rate quoted for this item.

ITEM NO.173 : Point wiring with 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper conductor for one light point controlled by two 2 way switches and including PVC rigid concealed conduit medium grade 19/20 mm dia to be terminated in pressed steel cadmium plated terminal box not less than 1.6mm thick for mounting Modular type switches, sockets, fan regulators etc with modular top cover including 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper earth continuity conductor including repairing the surfaces in CM 1:3 and finishing the surface as per existing treatment all as specified and directed by Engineer-in-Charge ( Wiring shall be done as per colour code in IS for phase, neutral and earth). (Note:- Cost of Eye/bottle thimbles used for connections in switches,sockets,MCBs in DBs shall deemed to be included in the unit rate quoted for this item.

ITEM NO.174 : Description All as per Sl item No 172 above herein before but one 6 Amp socket point on independent board.

ITEM NO.175 : Description all as per Sl item No 172 above herein before but 6 Amp socket point on same board but with other switches.

ITEM NO.176 :Description all as per Sl item No 172 above herein before but one socket out let 5 pins 16 Amp independent with 2.5 Sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper earth continuity conductor.

ITEM NO.177 : Point wiring with 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper conductor for one light/fan in existing conduit to be terminated in pressed steel terminal boxes with top cover plate including 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper earth continuity conductor controlled by one switch and/or one regulator complete including repairing the surfaces in CM 1:3 and finishing the surface as per existing treatment all as specified and directed by Engineer iin-charge Note-I-(Switches and regulators shall be measured and paid for separately). Note-II- ( Wiring shall be done as per colour code in IS for phase, neutral and earth). Note-III- (The cost of hylem cover plate and metal boxes is deemed to be included in the unit rate quoted for this item). Note -IV - cost of Eye/bottle thimbles used for connection in switches/sockets & MCBs in DBs is deemed to be included in the unit rate quoted for this item.

ITEM NO.178 : Description All as per Sl item No 177 here in before but one 6 Amp socket point on independent board .

ITEM NO.179 : Description all as per Sl item No 177 above here in before but one socket out let 5 pins 6 Amp on the same board but with other switches

ITEM NO.180 : Descripton all as per Sl item No 177 above here in before but one socket out let 3 pin 16 Amp Independent with 2.5 sqmm wire including 2.5 sqmm PVC insulated and unsheathed FRLS single core stranded copper earth continuity conductor.

ITEM NO.181 : Modular switch 1 way, 6 Amps, 1 module complete all as specified and directed by Engr-in-charge.

ITEM NO.182 : Modular switch 2 way, 6 Amps, 1 module complete all as specified and directed by Engr-in-charge.

ITEM NO.183 : Modular Bell switch 1 way, 6 Amps, 1 module complete all as specified.and directed by Engr-in-charge.

ITEM NO.184 : Modular switch 1 way, 16 Amps, 1 module complete all as specified and directed by Engr-in-charge.

ITEM NO.185 : Modular socket 5 pin 6 Amps, 2 module complete all as specified and directed by Engr-in-charge.

ITEM NO.186 : Modular socket 5 pin 6/16 Amps, combination type 2 module complete all as specified and directed by Engr-in-charge.

ITEM NO.187 : Fan regulator modular type 2 module complete all as specified and directed by Engr-in-charge.

ITEM NO.188 : Ceiling rose surface bakelite surface 65 x 50mm 3 terminals all as specified & directed by Engr-in-charge.

ITEM NO.189 : Bell ding dong electronic complete all as specified and directed by Engineer-in-charge.

ITEM NO.190 : Lamp holder including LED bulb 9 W including flexible wire 0.5 Sqmm copper cable all as specified & directed by Engr-in-charge.

ITEM NO.191 : Tube light fitting Self Ballasted LED Batten. Extruded Thermoplastic body with PC Diffuser in square LED Batten 18/20W 6500K of capacity ,20 watt,4 ft long incl 3 core flexible wire 0.5 sqmm copper cable all as specified and directed by Engr-in-charge.

ITEM NO.192 : Tube light fitting Self Ballasted LED Batten. Extruded Thermoplastic body with PC Diffuser in square LED Batten 10/12W 6500K of capacity ,watt,2 ft long incl 3 core flexible wire 0.5 sqmm copper cable all as specified and directed by Engr-in-charge.

ITEM NO.193 : Surface Mounted LED Bulk Head Luminaire of capacity 10 watt with ABS Body & Polycarbonate Diffuser, IP54 inc connection with ,with flexible wire 0.5 sqmm copper cable all as specified & directed by Engr-in-charge.

ITEM NO.194 : Sheet metal enclosure 8 ways double door for DBs when MCBs are to be used 240,volts including 200 Amps standard bus bar of suitable size and common neutral link all flush mounting type, drilling holes for incoming and out going cables with IP43 protection complete all as specified & directed by Engr-in-charge.

ITEM NO.195 : Sheet metal enclosure 6 ways double door for DBs when MCBs are to be used 240 Volts including 200 Amps standard bus bar of suitable size and common neutral link flush mounting type, drilling holes for incoming and out going cables with IP42 protection complete all as specified & directed by Engr-in-charge.

ITEM NO.196 : Sheet metal enclosure DB TPN 4 ways double door 415 volts with 200 Amps standard bus bar of suitable size and common neutral link flush mounting type, drilling holes for incoming and out going cables complete with IP-54 protection complete all as specified and directed by Engr-in-charge

ITEM NO.197 : MCB four pole, 415 Volt , 40 amp, 25 kA for fixing in DBs of including proper thimble connections complete all as specified and directed. all as specified & directed and directed by Engr-in-charge

ITEM NO.198 MCB four pole, 415 Volt , 63 amp, 25 kA for fixing in DBs of including proper thimble connections complete all as specified and directed by Enginner-in Charge.

ITEM NO.199 : MCB , SPN, 240 Volts ,32-40 amp for fixing in DBs of including proper thimble connections complete all as specified and directed by Engineer-in-Charge.

ITEM NO.200 : MCB, single pole 240 volts 6 to 32 Amp capacity for fixing in DB’s including proper thimble connections complete all as specified and directed by Engineer-in-Charge.

ITEM NO.201 : Sub main wiring with two single core 4.0 Sqmm PVC insulated and unsheathed FRLSH ,stranded copper conductor cable drawn through PVC concealed conduit 25 mm dia including 4 Sqmm PVC insulated unsheathed FRLSH stranded copper conductor cable as earth wire all as specified and directed by Engineer-in-charge. Note 1:- 2 Runs of 4.00 Sqmm Copper conductor cable, 1 Run of PVC conduit & 1 Run of 4.00 Sqm Copper conductor Earth wire shall be measured as one unit) Note2 : Rate quoted for this items shall be inclusive of the cost of (i) Rigid non-metallic PVC conduit of 25 mm dia with tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. (ii) Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to match the existing surfaces, cutting not exc. 10 cm girth . (iii) Taking out/down existing unserviceable sub main wiring.

ITEM NO.202 : Sub main wiring with two single core 6.0 Sqmm PVC insulated and unsheathed FRLSH ,stranded copper conductor cable drawn through PVC concealed conduit 25 mm dia including 6.0 Sqmm PVC insulated unsheathed FRLSH stranded copper conductor cable as earth wire all as specified and directed by Engineer-in-charge. Note 1:- 2(two) Runs of 6.00 Sqmm Copper conductor cable, 1 Run of PVC conduit & 1 Run of 6.00 Sqm Copper conductor Earth wire shall be measured as one unit) Note 2 :(i) Rate quoted for this items shall be inclusive of the cost of (i) Rigid non-metallic PVC conduit of 25 mm dia with tees, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. (ii) Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to match the existing surfaces and cutting not exc. 10 cm girth . (iii) Including taking out/down existing unserviceable sub main wiring.

ITEM NO. 203 : Sub main wiring with 04 (Four) single core 10.0 Sqmm PVC insulated and unsheathed FRLSH ,stranded copper conductor cable drawn through pvc concealed conduit of suitable dia including 10.0 Sqmm PVC insulated unsheathed FRLSH stranded copper conductor cable as earth wire all as specified and directed by Engineer-in-charge. Note1:- 4 Runs of 10.00 Sqmm Copper conductor cable, 1 Run of PVC conduit & 1 Run of 10.00 Sqm Copper conductor Earth wire shall be measured as one unit) Note2 : Rate quoted for this item shall be inclusive of the cost of (i) Rigid non-metallic PVC conduit of suitable size dia with tees, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. (ii) Cutting chases, pinning in and making good to facing where required pointing in cement mortar 1:3 to match the existing surfaces and cutting not exc. 10 cm girth. (iii) Taking down/out existing unserviceable sub main wiring.

ITEM NO. 204 : Rigid non-metallic PVC conduit of 25 mm dia exclusive of boxes (junction/ terminal) but inclusive of tees,bends,elbows,reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc all as specified and directedby Enginner-in-charge.

ITEM NO. 205 : Taking down and refixing of ceiling fan after necessary cleaning painting making serial No complete all as specified and directed by Enginner-in-charge.

ITEM NO. 206 : Supply and fix two way DB with MCB isolator DP 32 amp complete all as specified and directed by Engineer-in-charge.

ITEM NO.207 : Earthing complete with galvanised steel earth plate electrode, 600x600 x 6.0mm thick buried directly in ground(earth pit not less than 2.25m deep below normal level) connected to galvanised earth lead wire 4.0mm dia by means of nuts, bolts, & washers of GI as shown in electrical plate No 3 of SSR Part I. Connected to earthing test point testing complete including necessary earth pit chamber PCC 1: 3: 6 type C1, and 50mm thick RCC 1 : 2: 4 chamber cover and with 8mm dia mild steel re-enforcement @ 15Cm C/C spacing both ways with a handle made of 8 mm bar for fitting, galvanised iron funnel, wire mash watering pipe GI 20 mm dia light grade, and protection to earth lead shall be provided with GI pipe light grade 15mm dia up to 7.5m from the earth plate electrode, excavation including charcoal and common salt in alternative layers 15 cm Thick mixed refilling of soil etc complete all as directed by Engineer-in-charge.

ITEM NO.208 : Water heater (Geyser) storage type electric of capacity 25 ltr BEE 5 star rated, ABS body, metal tank with glass lined coating multiple heating option, shock safe plug puf insulation, incoly glass coated anode rod/copper heating element with ISI mark, adjustable knob for temp setting with minimum & bar high working pressure, multi functinoal saftey value, & whirl/swril flow technology, themostat electronic type, complete including superior quality copper connection pipe heavy duty 15 mm dia 450 mm long, brass adopter for water connection with nickel coated ISI marked with fastener, nut bolt, washers duly grouted, giving shape to hole as suitable and plastering including making good of disturbed surface as per exisiting surface connection to inlet and outlet valves, testing complete all as specified and dirceted by Engineer-in-Charge.

ITEM NO. 209 : Exhaust fan AC single phase 230/240 v of size 300 mm sweep 900 rpm metal body, high efficiency motor, dynamically balanced blade for better performance and corrosion-resistant powder coated metallic finish including Louver complete all as specified and directed by Engineer-in-Charge.

ITEM NO. 210 : XLPE Insulated ,screened, PVC bedded, galvanized steel wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core supplied & laid in replacement complete all as specified& directed by Engineer-in-Charge.

ITEM NO. 211 : XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volt grade of cross sectional area 16 Sqmm 4 core wire armoured supplied & laid in replacement complete all as specified & directed by Engr-in-Charge.

ITEM NO. 212 : Sheet metal enclosure suitable for fixing DB and Electric meter, factory made of size 60 x 60 x 18 cm made out of 2mm thick MS sheet with double door, sutiable locking arrangements, powder coated, cutting chasing in wall and fixing and making good as per existing surface complete including removing old one, complete all as specified and directed by Engineer-in-charge.

ITEM NO. 213 : Ceiling fan 1200mm sweep energy efficent as per latest specifications having service value more than or equal to 4.5 and suspended from fan hook including electrically connecting with twisted three core PVC insulated unsheathed flexible cord of 0.75 Sqmm copper conductor from ceiling rose to ceiling fan complete all as specified & directed by Enginner-in-charge.

ITEM NO. 214 : Single pole and neutral Sheet metal enclosure (industrial socket) with a two pin and earth plug socket for AC complete with one single pole MCB 16 to 20 Amp, 240 Volts all as specified & direction by Enginner-in-charge.

ITEM NO. 215 : New generation energy saving and environmental friendly long life LED building security light 1x25 watts made up of pressure die cast alluminium housing with high power LED as light source and lense embedded PC cover having TOP OPENING separate driver compartment with IP65 protection and impact resistance of IK07, with all accessories including suitable bracket with 32mm bore light grade GI pipe bemd to shape, including MS clamp of size of required size and PVC cable 1.5 Sqmm twincore from ceiling rose to light fittings complete all as specified and directed by Engineer-in-charge.

ITEM NO. 216 : IP 55 Surface mounted LED Porch light 12 watt in engineering plastic housing with clear plastic housing with clear prismatic diffuser complete all as specified and directed by Engineer-in-charge.

ITEM NO. 217 : Sand cushioning for cables 8 cm below the cable and 15 cm above the cable punning down to 18 cm thickness all as specified and directed by Engineer-in-charge. (Note: Only punned thickness shall be measured for payment purpose).

ITEM NO.218 : Supplying and laying unreinforced precast concrete cable cover conforming to IS, Class LV, Type I, flat, size 250 mm x 150mm x 40mm for protection of LT cable 1100 V complete all as specified and directed by Engineer-in-charge.

ITEM NO.219 : Replacement of GI tubing light grade 32 mm bore for passing through cables under the floor ,along the wall or along the pole complete all as specified and directed by Engineer-in-charge.

ITEM NO.220 : Replacement of GI tubing light grade 40 mm bore for passing through cables under the floor ,along the wall or along the pole complete all as specified and directed by Engineer-in-charge.

ITEM NO.221 : Cutting of hardstanding/wall for laying of cable including matching with suface by using cement concrete all as specified and directed by Engineer-in-charge.

ITEM NO.222 : Boring of under road/ hard standing by manually for laying XLPE cable with GI pipe upto 40 mm dia all as specified and directed by Engineer-in-Charge. Note: GI pipe shall be measured and paid seperately under relevant item.

ITEM NO.223 : MCCB, 4 Pole, 100 A, 25 KA for fixing in DB including proper thimble connection, thermal and magnetic release protection complete all as specified and directed by Engineer-in-charge.

ITEM NO.224 : MCCB, 4 Pole, 63 A, 18 KA for fixing in DB including proper thimble connection, thermal and magnetic release protection complete all as specified and directed by Engineer-in-charge.

ITEM NO.225 : Supply and fix epoxy power coated MCCB distribution distribution box double door VTPN 4 way vertical type AC 415 V with IP 43 protection for MCBs alongwith provision of MCCB as incomer with commen bus-bar at incoming end of outgoing MCBs grouted/ flush to wall, complete all as specified by Engineer-in-charge. (Note :- MCCB will be measured and paid under seperate item) (i) Cost of Eye/bottle thimbles used for connection in switches/sockets & MCBs in DBs shall deemed to be included in unit rate quoted for this items, (ii) Electric wiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for Earth.

For the purpose of arriving at lumpsum amount, the amount of credit sch for building (i.e Rs 3404785.00) shall be deducted from the total amount arrived.

Total of BOQ Rs.

M/S RAJ KUMAR GUPTA

SOM BUILDERS

M/S RAJINDER SINGH

Saru Enterprises Pvt Ltd

Shree Construction Co.