Development of Accomodation Facilities and Development of Picnic Spot At Nakachikong North Garo Hills Meghalaya

BoQ_Ver4.0

UnderWater Lights Supplyof UnderwaterLights LED13.5W/12Vwhitewithniche.Madeof Pool grade, anti UV treatedABS ,self adhesive elastomer seals. IP-X8 , meet the Stringent stipulations laid out in the electrical insulation standard NF-C-15-100 Supplying of Step down Transformer 300VA, 240 /12V output with multi out put tappings of 12V,13V,14V and 16V. : Universal Deck box ,2 outlets and 1 inlet. Including all accessories in white ABS. IP 65 rating.Model- BC-84 .

Name of the Bidder/ Bidding Firm / Company :

Supply , Installation , Testing and Commissioning of EPABX as per attached specifications Supply , Installation , Testing and Commissioning of Analog Phone with CLI Supply , Installation , Testing and Commissioning of Digital Phone

IR Dome Camera , 5MP (2880×1620) resolution,1/2.7" CMOSCMOS complete as per attached specifications Supply , Installation , Testing and Commissioning of IP outdoor PTZ camera as per attached specifications Supply , Installation , Testing and Commissioning of 24 Port POE + Switch With 380 Watts Power Budget and 5 Year Replacement Warranty complete as per attached specifications Supply , Installation , Testing and Commissioning of RJ45 Connectors Supply , Installation , Testing and Commissioning of 32 Ch NVR as per attached specifications Supply , Installation , Testing and Commissioning of 6 TB Survellance HDD as per attached specifications Supply , Installation , Testing and Commissioning of CAT6 Cable (Indoor) complete as per attached specifications Supply , Installation , Testing and Commissioning of 42 " /43" Display as per attached specifications Supply , Installation , Testing and Commissioning of 3 KVA online UPS as per requirement Supply , Installation , Testing and Commissioning of 18 U Network rack with accessories as per attached specifications

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in-Charge:

All kind of Soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m,as directed by Engineer-in-charge

All kind of Soil

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge

Ordinary rock

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains ( exceeding or not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kind of Soil

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (exceeding or not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.

Ordinary rock

Excavating trenches by mechinical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m:

All kinds of soil

Pipes cables etc. exceeding 80 mm dia. But not exceeding 300mm dia.

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials

All kinds of soil

Ordinary or hard rock

Filling

available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.

Supplying and stacking at site/ Good earth

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Earth work in excavation by manual means up to depth of 2m below the existing ground level for foundation trenches of foundation ,footing of column/walls,retaining walls septic tank etc. including bailing out water where necessary and removal of surplus earth with all lead nd lifts as directed and specified for the following classification of soil.

All kind of Soil (ordinary soil /hard soil/dense soil)

Earth work in excavation by mechanical means up to depth of 2m below the existing ground level for foundation trenches of foundation ,footing of column/walls,retaining walls septic tank etc. including bailing out water where necessary and removal of surplus earth with all lead nd lifts as directed and specified for the following classification of soil.

In ordinary rock (soft rock /medium rock/ hard shale)

CEMENT CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shttering - All work up to plinth level

1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

1:2:4 (1 cement: 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 20 mm nominal size derived from natural sources)

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)

1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) ( Using in front side ramp bottom layer )

1:5:10 (1 cement: 5 coarse sand (zone-III) derived from natural sources: 10 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing.

1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in charge).

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources).

per 50kg cement

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

REINFORCED CEMENT CONCRETE WORK

Centering & shuttering including strutting, propping etc. and removal of form work for:

Foundations, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters, butteresses,plinth and string courses etc..(using steel)

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Edges of slabs and breaks in floors and walls

Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like

Under 20 cm wide

Above 20 cm wide

Weather shade, Chajjas, corbels etc., including edges

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level..

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level..

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level..

Providing and laying in position ready mixed or site batcheddesign mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement

All works upto plinth level

Providing and laying in position ready mixed or site batcheddesign mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement

Concrete of M25 grade with minimum cement content of 330 kg /cum

All works above plinth level upto 1st floor level

Providing and filling in position bitumen mix filler of Proportion 80 kg. of hot bitumen , 1 kg. of cement and 0.25 cubic metre of coarse sand for depth per expansion joints.

Providing and filling in position bitumen mix filler of Proportion 80 kg. of hot bitumen , 1 kg. of cement and 0.25 cubic metre of coarse sand for depth per expansion joints.

Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge.

per cm depth per cm width per metre length

BRICK W O R K

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

Cement mortar 1:4 (1 cement : 4 coarse sand)

BRICK W O R K

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

Cement mortar 1:4 (1 cement :4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in :

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with :

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

STONE W O R K - RANDOM RUBBLE MASONRY

Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like.1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like.

Dry stone pitching 22.5 cm thicj laid in course and requireed profile with hammer dressed stones having no side less than 15 cm, including prepareing the bedding surface etc.all complete(payment for stone to be separately)

Providing dry stone masonary inretaining wall etc with hammert dressed or blunt chisel dressed stone of heavy section not less than 25x25x30cm with proper key stone each not less than 25x25x25 cm long including fillings of trenches and providing of weep holes at 1.20 to 1.50 metre aparts

WOOD & PVC WORK

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Second class teak wood

Kiln seasoned and chemically treated hollock wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :

2nd class teak wood

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to steel windows by welding

Providing and fixing expandable fasteners of specified size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete.

50 mm long

Providing and fixing chromium plated brass 50 mm cupboard or wardrobe knobs with nuts complete

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.:

Single rubber stopper

Twin rubber stopper

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete.

Triple strip vertical type

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineerin-charge

Extruded section profile size 48x40 mm

25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded

PVC section of the size of 762 mm 25 mm or less as per requirement with an average wall thickness of 1 mm (± 0.3 mm). PVC foam end cap of size 23x10 mm are provided on both vertical edges to ensure the overall thickness of 25 mm. M.S. tube having dimensions 19 mm x 19 mm and 1.0 mm (± 0.1 mm) is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top & Bottom edges of the shutter are covered with an end-cap of the size 25 mm X 11 mm. Door shutter shall be reinforced with special polymeric reinforcements as per manufacturer’s specification and direction of Engineer-in-charge to take up necessary hardware and fixtures. Stickers indicating the locations of hardware will be pasted at appropriate places

STEEL W O R K

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.

Using flats 30x6mm for diagonal braces and central cross piece

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding,top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.

M.S. tube

Supplying and fixing rolling shutters of approved make, made of requiredsize M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside andoutside l ocking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.

80x1.25 mm M.S. laths with 1.25 mm thick top cover

Hot finished welded type tubes

Supplying at site Angle iron post & strut of required size including bottom to be split and bentb at right angle in opposite direction for 10 cm length and driling holes to 10 mm dia etc.complete

kilogram

Providing and fixing G.I chain linked fabric fencing of required width in mesh size 50x50 mm including strengthenning with 2mm dia wire or nuts ,bolts and washers required complete as per diecion Engineer in charge

Made of G.I wire of dia 4 mm PVC coated to achive outer dia not less than 5 mm in required colour and shade

FLOORING WORK

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.

18 mm thick

Extra for making chequers of approved pattern on cement concrete floors, steps, landing, pavements etc.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

WOOD & PVC WORK

25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with :

Providing and fixing timber skirting with butt joining and screws ( frame work to be measured and paid seperately)

teak wood

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system a

nd rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size

Size of Tile 600x600 mm

ROOFING WORK

ROOFING WORK (SYNTHETC THACH ROOF)

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

In 75x75 mm deep chase

Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete

0.80 mm thick with zinc coating not less than 275 gm/Sqm

Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete

0.80 mm thick with zinc coating not less than 275 gm/m²

Providing and fixing of 40 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts, G.l. limpet and bitumen washer complete, bent to shape and fixed in wall with cement mortar 1:3 (1 cement : 3 coarse sand).

1.00 mm thick with zinc coating not less than 275 gm/m²

Providing single layer of bamboo mat lining over thatch roofing frame cpmplete

providing bamboo roof frame with kami of size 30x6 mm complete as directed

Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixedwith 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately).

Providing and fixing 100 mm diameter and 60 cm long rain water spout in cement mortar 1:4 (1 cement : 4 fine sand).

Stone ware spout

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Single tee with door

Single tee without door

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

110 mm bend

Shoe (Plain)

110 mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Painting top of roofs with bitumen of approved quality @ 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete :

With residual type petroleum bitumen of grade VG -10

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

0.63 mm thick with zinc coating not less than 275 gm/ m²

FINISHING W O R K

0.63 mm thick with zinc coating not less than 275 gm/ m²

12 mm cement plaster of mix :

0.63 mm thick with zinc coating not less than 275 gm/ m²

1:4 (1 cement : 4 fine sand)

1:6 (1 cement: 6 coarse sand)

15 mm cement plaster on the rough side of single or half brick wall of mix :

20 mm cement plaster of mix :

12 mm cement plaster finished with a floating coat of neat cement of mix:

1:4 (1 cement: 4 fine sand)

6mm cement plaster 1:3

1:3 (1 cement : 3 fine sand)

Neat cement punning.

White washing with lime to give an even shade :

New work (three or more coats)

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gm per liter , of approved manufracturar and of required shade and colour all complete to achive even shade and colour

New work ( two or more coats) over and including water thinable priming coat with cement primer having VOC content less than 50 gm per liter

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives.

New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Wall painting with acrylic emulsion paint of approved brand and

Two or more coats on new work

Finishing walls with water proofing cement paint of required shade :

New work (Two or more coats applied @ 3.84 kg/10 sqm)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Extra for providing and mixing water proofing material in cement Per bag of plaster work in proportion recommended by the manufacturers.

ALUMINIUM WORK

Extra for providing and mixing water proofing material in cement Per bag of plaster work in proportion recommended by the manufacturers.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin-charge

Pre-laminated particle bo

ard with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

With stainless steel cover plate minimum 1.25 mm thickness

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.

Upto 5mm depth and 5 mm width

metre

Extra for applying additional anodic coating AC 25 instead of AC 15 to aluminium extruded sections.

For shutters of doors, windows & ventilators

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge.

Polyester powder coated minimum thickness 50 micron aluminium tubular handle bar

Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Fixed window / ventilator without mullion / transom.

Using R1 series with frame (33 mm & above) x (35 mm & above). (height upto 0.90 metre)

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.

WATER PROOFING WORK

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels/ subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guaranteed for 10 years against any leakage

For horizontal surface one coat @1.10 kg per sqm.

FALSE CEILING

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.

With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles.

Providing and fixing at all height false ceiling of 4mm thick phenol bonded Bamboo Mat board (595x595mm) conforming to IS:13958-1994 including providing and fixing of frame work made of GI angle 25x25x0.4 mm thick all around suitably fixed to wall with the help of dash fastener and hanger frame (600x600 c/c) made GI slotted Tee having powder coating on bottom side (30x25x0.3 mm thick for main member & 25x25x0.3 mm for cross member) connected to ceiling with 2.64mm GI wire and anchor fastener at every junction and also including cost of making openings for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed all complete as per direction of Engineer-in-charge.

PRE-CONSTRUCTIONAL ANTI-TERMITE WORK

Anti termite treatment to bottom surface ( in case of masonry foundation and basements) and the sides (upto a height of 300 mm. from bottom) of the excavation trenches with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight at the rate of 5 Litres per sq. m. area. The work shall be carried out as per specification described in 6.2.1. of code IS- 6313 (part -II) 1981. (Mode of measurment will be the plan area of foundation treated.)

Anti termite treatment to the top surface of the consolidated earth within plinth walls with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight at the rate of 5 Litres per sq. m. of the surface before sand bed or sub-grade is laid. Holes upto 50 mm. to 75 mm. deep at 150 mm. centre to centre both ways shall be made with 12 mm, diameter mild steel rod on the surface to facilitate saturation of the soil with the chemical emulsion. The work shall be carried out as per specification described in para 6.4 of code IS-6313 (part -II) 1981.( Mode of measurment will be per Sq.m of plan area of plinth treated.)

Treatment to the back filling of R.C.C. foundation with chemical emulsion by admixing chloropyrofos emulsifiable concentrate (1% concentration) with water by weight at the rate of 7.5 ltr. per sq.m. of the vertical surface of the substructure of each side ofthe foundation. The work shall be carried out as per specification as described in para 6.3.1 of code IS- 6313

(part-II) 1981 (Mode of measurement will be per sq.m. of vertical area of foundation treated).

OTHER TECHNOLOGY WORK

Providing and fixing UV stabilized fibreglass reinforcement plastic sheet roofing up to any pitch, including fixing with polymer coated 'j' or 'L' hooks ,bolts & nuts 8 mm dia G.I plain/bitumen washers complete but excluding the cost of purlin .rafter trusses,etc.the sheet shall be manufactureed out of 2400 TEX panel rovigs incorporating minimum 0.35 ultra violet stabilizer in resin system underapproximately 2400 psi and hot cured. they shall be of uniform pigmentation and thickness without air pocket and shall confirm to IS:10192 and IS:12866.the sheet shall be opaque or translucent, clear or pigmented,textured, or smooth as specified

2 mm thick flat

Extra for providing openning of requireed size & shape for wash basin /kitchen sink in kitchen platform ,vanity counter and similar lockation in marble/granite/ stone work, including necessary holes for pillar taps etc. Including moulding rubbing and polishing of cut edges etc.complete

Bamboo (Dry) Posts, pole fencing, etc. exposed to weather and in contact with ground level having 6-8 persent preservatives concentration and 80-128, 10-14,8-12 kg/m of preservatives absorption.Methode of treatment including hot and cold ,vacuum/pressure process, Diffusion,Boucherie process, modified Boucherie process and butt end treatment. Length 6 m and dia 50-70 mm.

Soft furnishing & furniture(ACCOMODATION L-1)

Soft furnishing & furniture(ACCOMODATION L-2)

Soft furnishing & furniture(ACCOMODATION L-3)

Soft furnishing & furniture(RESTAURANTS BLOCK)

Soft furnishing & furniture (PICNIC HUT)

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying Double Flanged (screwed / welded) Centrifugally (Spun) Cast Iron, Class B (IS : 1536) :

350 mm dia C.I. Double Flanged Pipe

Providing and fixing soil, waste and vent pipes :

100 mm dia

Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989

AGGREGATE WORK

Supplying and stacking at site.

90 mm to 45 mm size stone aggregate

63 mm to 45 mm size stone aggregate

stone screening 13.2 mm nominal size

Red bajri

BOREWELL & SUBMERSIBLE PUMP

stone screening 13.2 mm nominal size

Red bajri

SCHEDULE ITEM

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level.

300 mm dia

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

200 mm nominal size dia

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

80 mm nominal bore

NON SCHEDULE ITEM

Supply & installation of submersible pump of make KSB 7.5 HP with control panel, support wire etc. complete.

7.5 HP PUMP - 2 Nos. with installation

Providing & fixing 3 core 4 sqmm Copper stranded conductor submersible flat cable connected to pump with water proof joint and connection to submersible panel board with necessary lugs, etc.

Installation and Commissioning of pump set and all other necessary fitting.

Mobilization & Demoblilization of drilling rig at site along with other related equipments

Geophysical study for calculations of zone wise aquifer characteristics along with the designs of tube well etc.

Collection of drill cutting samples, analysis of samples, preparation of logs, logs analysis of all the drilling data for designing the well assembly for lowering.

Geophysical logging ( using Sp, 16-64-N & lateral ) of the borehole to demarcate the exact aquifers for deciding well assembly in corroboration with lithologs

Providing & fixing factory made out door type, weather proof Panel Board for submersible pump with 7.5 HP m

otor, fitted with DOL starter, ammeter, voltmeter, single phase preventer MCB’s, on/ off switch push botton duly wired and made out of 14 SWG sheet, complete with locking arrangements, grouted on ground, complete as directed by Project Director / Architect.

NS ITEM

STP MACHINE

LANDSCAPING

Supplying to Site and installing in position of Filter SM1200mm dia with 3" side mount Multiport valve. Bobbin wound filter reinfirced polyester shell, wide transparent lid diameter -250mm,Stainless steel pressure guage integrated into the 6 way valve, valve enclosed with the connection kit to be glued and assembled.Maximum operating pressure 4.0Bar . Flow rate- 46m3/hr. Supply of Filter media - 1100kg Sand , 300 kg Gravel for one filter Supply to site and installing in position Filteration Pump with Prefilter, Pump Body and prefilter are made from glass loaded Polypropylene ,Corrosion resistant even suitable for salt water ,water tight maintenance free mechanical seal self priming , 2840 RPM,3.3kW/3Phase and inlet /outlet size 90mm.Flow rate 45m3/h @10 m head.Pump Model :BADU 95/45. A tool provided for closing and opening for prefilter lid. (3 Working + 1 Standby).

BoQ_Ver4.0

Supply of Dosing pump having capacity of 10ltrs/ hr, dosing rate@4kg /cm2 , suction/discharge tubing 4 /5mm. Material of construction All wetted parts are in polypropelene, viton ,Teflon, HDPE and glass filled PP. Operating panel protection provided by moulded ABS plastic cover. Adjustable Frequency upto 400spm , Power rating -230V- 50Hz,IP65- Protection included in all accessories.PTFE Diaphragm for longer life. Storage tank for Dosing Pumps 200ltrs. Supply of Manual Agitator shaft length 900mm.

Name of the Bidder/ Bidding Firm / Company :

Supply , Installation , Testing and Commissioning of EPABX as per attached specifications Supply , Installation , Testing and Commissioning of Analog Phone with CLI Supply , Installation , Testing and Commissioning of Digital Phone

IR Dome Camera , 5MP (2880×1620) resolution,1/2.7" CMOSCMOS complete as per attached specifications Supply , Installation , Testing and Commissioning of IP outdoor PTZ camera as per attached specifications Supply , Installation , Testing and Commissioning of 24 Port POE + Switch With 380 Watts Power Budget and 5 Year Replacement Warranty complete as per attached specifications Supply , Installation , Testing and Commissioning of RJ45 Connectors Supply , Installation , Testing and Commissioning of 32 Ch NVR as per attached specifications Supply , Installation , Testing and Commissioning of 6 TB Survellance HDD as per attached specifications Supply , Installation , Testing and Commissioning of CAT6 Cable (Indoor) complete as per attached specifications Supply , Installation , Testing and Commissioning of 42 " /43" Display as per attached specifications Supply , Installation , Testing and Commissioning of 3 KVA online UPS as per requirement Supply , Installation , Testing and Commissioning of 18 U Network rack with accessories as per attached specifications

POOL BASIN EQUIPMENTS

90 deg Corner tiles for gratings 295mm for 300mm

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

One urinal basin with 5 litre white P.V.C. automatic flushing cistern

WATER SUPPLY

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clampsat 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing toilet paper holder :C.P. brass

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Concealed work, including cutting chases and making good the walls etc.

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

External work

40 mm nominal outer dia Pipes

50 mm nominal outer dia Pipes

65 mm nominal outer dia Pipes

50 mm nominal outer dia Pipes

80 mm nominal dia Pipes

100 mm nominal dia Pipes

50 mm nominal outer dia Pipes

150 mm nominal dia Pipes

BRASS FITTINGS

Providing and fixing brass bib cock of approved quality :

20 mm nominal bore

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Providing and fixing brass stop cock of approved quality :

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

50 mm nominal outer dia Pipes

100 mm nominal dia Pipes

25 mm nominal bore

32 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

50 mm nominal outer dia Pipes

40 mm nominal bore

100 mm diameter

65 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

15 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length

100 mm diameter

50 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

150 mm diameter

Providing and fixing in postion pre cast RCC manhole cover and frame of required shape approved quality

HD-20 circular 560 mm internal dia

DRAINAGE

STONE WARE

PIPES AND FITTINGS

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :

200 mm diameter

250 mm diameter

300 mm diameter

Soft furnishing & furniture (PICNIC HUT)

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :

100 mm diameter S.W. pipe

150 mm diameter S.W. pipe

200 mm diameter S.W. pipe

250 mm diameter S.W. pipe

300 mm diameter S.W. pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:

180x150 mm size P type

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :

150 mm dia. R.C.C. pip

250 mm dia. R.C.C. pip

300 mm dia. R.C.C. pip

450 mm dia. R.C.C. pip

600 mm dia. R.C.C. pip

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished witha floating coat of neat cement complete as per standard design :

meter

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

With common burnt clay F.P.S.(non modular) bricks of classic designation 7.5

Extra for depth for manholes :

Size 90x80 cm

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only)

NUMBER #

BoQ_Ver4.0

UnderWater Lights Supplyof UnderwaterLights LED13.5W/12Vwhitewithniche.Madeof Pool grade, anti UV treatedABS ,self adhesive elastomer seals. IP-X8 , meet the Stringent stipulations laid out in the electrical insulation standard NF-C-15-100 Supplying of Step down Transformer 300VA, 240 /12V output with multi out put tappings of 12V,13V,14V and 16V. : Universal Deck box ,2 outlets and 1 inlet. Including all accessories in white ABS. IP 65 rating.Model- BC-84 .

Name of the Bidder/ Bidding Firm / Company :

Supply , Installation , Testing and Commissioning of EPABX as per attached specifications Supply , Installation , Testing and Commissioning of Analog Phone with CLI Supply , Installation , Testing and Commissioning of Digital Phone

IR Dome Camera , 5MP (2880×1620) resolution,1/2.7" CMOSCMOS complete as per attached specifications Supply , Installation , Testing and Commissioning of IP outdoor PTZ camera as per attached specifications Supply , Installation , Testing and Commissioning of 24 Port POE + Switch With 380 Watts Power Budget and 5 Year Replacement Warranty complete as per attached specifications Supply , Installation , Testing and Commissioning of RJ45 Connectors Supply , Installation , Testing and Commissioning of 32 Ch NVR as per attached specifications Supply , Installation , Testing and Commissioning of 6 TB Survellance HDD as per attached specifications Supply , Installation , Testing and Commissioning of CAT6 Cable (Indoor) complete as per attached specifications Supply , Installation , Testing and Commissioning of 42 " /43" Display as per attached specifications Supply , Installation , Testing and Commissioning of 3 KVA online UPS as per requirement Supply , Installation , Testing and Commissioning of 18 U Network rack with accessories as per attached specifications

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :

0.91 m deep with SFRC cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) :

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m

With 20x20 mm square bar

Providing and laying Non Pressure NP-4 class (Heavy duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete

450 mm dia RCC pipes.

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

NON SCHEDULE

Group C

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 amps switch

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

3 Module (100mmX75mm)

150 mm X 150 mm X 60 mm deep

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Supplying and fixing,connecting,testing and commossinning ofcalling bell /bell indicator type suitable for 230V as well as battery operated complete with all necessary accessories.

Supplying and fitting of ceilling fan AC operated type 220/250 volt completed with 3nos blade down rod canopy hanging shale & 30 mm length of down rod supplied with the fan by the dealer but the extra length will be charged @Rs.25.00/ Mtr.

Ac ceiling fan 1200 mm sweeps

Supply and fixing of exhaust fan double bearing self lubricating type single phase 50 hz 250V AC operated complete with supporting frame, fan blades,nuts, and bolts all necessary action.

Supply fitting and fixing of water heater (Geyser)of 1.5 kw with pressure release valveincluding all necessary action.

15 lit capacity

12 way (4 + 36), Double door

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Tripple pole MCB

DP MCB

Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required. 315 A TP&N

LT PANEL BOARDS - (Low Voltage Switchgear)

MAIN UTILITY PANEL-1

MAIN LT PANEL (INDOOR TYPE)

SUB FEEDER PILLAR-1-3(OUTDOOR TYPE)

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

SUB FEEDER PILLAR-4(OUTDOOR TYPE)

75 KVR APFC PANEL

EARTHING SYSTEM

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

Supply and installation of Asthetically designed wall mounted decorative light

Supply and installation of LED UP light as required

Suply and installation of 20W LED BATTEN Light on wall /surface

Suply and installation of Surface 15W LED Panel Light

Supply and installation of LED bollard light cat no.BCP150LEDIWWPSU220-240 or equivalent.

Supply and installation of post top light with 3.5 meter pole with all nesessary arrangement.

Supply and installation of post top 15W light with 3.5 meter pole with all nesessary arrangement.

Supply and installation of post top36W light with 4 meter pole with all nesessary arrangement.

Supply installtion of led mirrior light with all necessary action.

SUPPLY OF MV CABLES

Supplying of the following sizes of XLPE insulated, multistand Al. & Cu. Conductor armoured cables of 1.1KV grade on the surface of wall or on existing cable trays or existing Under Ground cable trench complete with fixing hardware etc. as required.

with 4CX16 sqmm

with 4CX6 sqmm

with 4CX16 sqmm

with 3CX16 sqmm

with 4CX16 sqmm

with 3.5CX185 sqmm

with 3.5CX300 sqmm

LAYING OF MV CABLES

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

upto 35 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Supply and installation of LED bollard light cat no.BCP150LEDIWWPSU220-240 or equivalent.

Supply and installation of post top light with 3.5 meter pole with all nesessary arrangement.

Supply and installation of post top 15W light with 3.5 meter pole with all nesessary arrangement.

Supply and installation of post top36W light with 4 meter pole with all nesessary arrangement.

Supply installtion of led mirrior light with all necessary action.

Supply installation of led strip light with all necessary action.

MV CABLES

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

from 35 sqmm upto 95 sq. mm

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

Red bajri

from 185 sqmm upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Upto 35 sq. mm (clamped with 1mm thick saddle)

CABLE ROUTE MARKER

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

MV CABLE JOINTING & END TERMINATION

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

HUME PIPE

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.

Supplying and embedding following dia G.I. pipe (medium class) in pole collar/ foundation (during casting) for cable entry including bending the pipe to the required shape complete as required.

40 mm dia

SOLAR 20 K.W

PV module @540W of 50 NOS

Grid tied 20 kw Sting Inverter

GI structure of industrial roof

BoQ_Ver4.0

UnderWater Lights Supplyof UnderwaterLights LED13.5W/12Vwhitewithniche.Madeof Pool grade, anti UV treatedABS ,self adhesive elastomer seals. IP-X8 , meet the Stringent stipulations laid out in the electrical insulation standard NF-C-15-100 Supplying of Step down Transformer 300VA, 240 /12V output with multi out put tappings of 12V,13V,14V and 16V. : Universal Deck box ,2 outlets and 1 inlet. Including all accessories in white ABS. IP 65 rating.Model- BC-84 .

Name of the Bidder/ Bidding Firm / Company :

Supply , Installation , Testing and Commissioning of EPABX as per attached specifications Supply , Installation , Testing and Commissioning of Analog Phone with CLI Supply , Installation , Testing and Commissioning of Digital Phone

IR Dome Camera , 5MP (2880×1620) resolution,1/2.7" CMOSCMOS complete as per attached specifications Supply , Installation , Testing and Commissioning of IP outdoor PTZ camera as per attached specifications Supply , Installation , Testing and Commissioning of 24 Port POE + Switch With 380 Watts Power Budget and 5 Year Replacement Warranty complete as per attached specifications Supply , Installation , Testing and Commissioning of RJ45 Connectors Supply , Installation , Testing and Commissioning of 32 Ch NVR as per attached specifications Supply , Installation , Testing and Commissioning of 6 TB Survellance HDD as per attached specifications Supply , Installation , Testing and Commissioning of CAT6 Cable (Indoor) complete as per attached specifications Supply , Installation , Testing and Commissioning of 42 " /43" Display as per attached specifications Supply , Installation , Testing and Commissioning of 3 KVA online UPS as per requirement Supply , Installation , Testing and Commissioning of 18 U Network rack with accessories as per attached specifications

BASIC RATE In Figures To be entered by the Bidder Rs. P

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

Providing and fixing 4 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Supplying, installation, testing and Commission of the following indoor luminaries Philips Dura Slim 15W Square LED Panels LED DOWNLIGHTS surface or wall mounted will all necessary accessories.

Inside size 120 x 90 cm & 90 cm deep including CI cover with frame (Medium duty) 560mm internal diameter, total wt. of cover & frame to be not less than 208 kg (wt. of cover 108 kg and wt. of frame 100 kg)

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

Providing M.S. foot restsOrange colour Safety footrest

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, 240 v, isolator in existing MCB DB complete with connections, testing and comissiioning etc, as required.

BoQ_Ver4.0

UnderWater Lights Supplyof UnderwaterLights LED13.5W/12Vwhitewithniche.Madeof Pool grade, anti UV treatedABS ,self adhesive elastomer seals. IP-X8 , meet the Stringent stipulations laid out in the electrical insulation standard NF-C-15-100 Supplying of Step down Transformer 300VA, 240 /12V output with multi out put tappings of 12V,13V,14V and 16V. : Universal Deck box ,2 outlets and 1 inlet. Including all accessories in white ABS. IP 65 rating.Model- BC-84 .

Name of the Bidder/ Bidding Firm / Company :

Supply , Installation , Testing and Commissioning of EPABX as per attached specifications Supply , Installation , Testing and Commissioning of Analog Phone with CLI Supply , Installation , Testing and Commissioning of Digital Phone

IR Dome Camera , 5MP (2880×1620) resolution,1/2.7" CMOSCMOS complete as per attached specifications Supply , Installation , Testing and Commissioning of IP outdoor PTZ camera as per attached specifications Supply , Installation , Testing and Commissioning of 24 Port POE + Switch With 380 Watts Power Budget and 5 Year Replacement Warranty complete as per attached specifications Supply , Installation , Testing and Commissioning of RJ45 Connectors Supply , Installation , Testing and Commissioning of 32 Ch NVR as per attached specifications Supply , Installation , Testing and Commissioning of 6 TB Survellance HDD as per attached specifications Supply , Installation , Testing and Commissioning of CAT6 Cable (Indoor) complete as per attached specifications Supply , Installation , Testing and Commissioning of 42 " /43" Display as per attached specifications Supply , Installation , Testing and Commissioning of 3 KVA online UPS as per requirement Supply , Installation , Testing and Commissioning of 18 U Network rack with accessories as per attached specifications