PROVN OF GUARD ROOM ALONG WITH TOILET AT BLDG 69 OF 5 SIKH TOILET BLOCK WITH 01 WC 05 URINALS NEAR BLDG E79 OF 1ST BIHAR TOILET AND BATH AT FOOTBALL GROUND OF 4TH JAK LI AND 230 M DRAIN IN FRONT OF MD ACCN 383 BLOCK AT 5 SIKH UNDER GE GOLCONDA

Amount

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in hard/dense soil all as specified and directed.

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.50m in depth and getting out in hard/dense soil all as specified and directed.

Excavation in trenches not exceeding 1.50m wide and depth exceeding 1.50m and n. exc 3.0 m and getting out in hard/dense soil all as specified and directed.

Returnng, filling in, soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm all as specified and directed.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point all as specified and directed.

M&L for hardcore using broken stone or boulders not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface all as specified and directed.

Labour only for Earth filling under floors including spreading, levelling in layers not exceeding 25cm thick and well ramming including watering as required all as specified and directed. Note: Serviceable earth obtained from excavation shall used for filling.

M&L for anti-termite treatment to the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area all as specified and directed.

M&L for anti-termite treatment the top surface of filled earth at rate of 5 litres of emulsion per square metre of surface area all as specified and directed.

M&L for anti-termite treatment the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area all as specified and directed.

Demolition of cement concrete unreinforced above/below ground floor complete all as specified and directed.

M & L for Sand filling under floors, in foundations including watering and consolidation all as specified and directed. Note: Punned thickess shall be measured and paid.

M & L for Sand cushioning to cable including consolidation all as specified and directed. Note: Punned thickess shall be measured and paid.

M&L Plain cement concrete (1:4:8) type D2 (40mm graded stone aggregate) in foundations, filling and mass concrete all as specified and directed.

M&L for pre-cast Reinforced cement concrete (1:2:4) type B1 (20 mm graded stone aggregate) as in cover slabe for manholes etc., and set in cement mortor (1:4) all as specified and directed. Note: (i) Cost of formwork reqd is deemed to be included in item rate quoted. (ii) Reinforecement will be measured and paid separately.

M&L for Plain cement concrete (1:3:6) type C1 (20 mm graded stone aggregate) as in coping, benching, bed blocks, cills etc., including necessary form work , complete all as specefied and directed.

M & L for Reinforced Cement Concrete (1:2:4) type B1 (20 mm graded stone aggregate) in foundations including rafts, footings and mass concrete, foundation beams, plinth beams, bases for columns, basement slabs etc., complete all as specified and directed.

M & L for Reinforced Cement Concrete (1:2:4) type B1 (20 mm graded stone aggregate) in Columns, posts and struts, complete all as specified and directed.

M&L for Reinforced cement concrete (1:2:4) type B1 (20 mm graded stone aggregate) in lintel bands, roof beams and cantilevers etc., all as specified and directed.

M&L for reinforced Cement Concrete (1:2:4) type B1 (20 mm graded stone aggregate) Chajjas, all as specified and directed.

M&L for Reinforced Cement Concrete (1:2:4) type B1 (20 mm graded stone aggregate) slabs supported on walls, beams and columns in floors, roofs, landings balconies canopies, desk slabs and in shelves etc., complete all as specified and directed.

M&L for Reinforced Cement Concrete (1:2:4) type B1 (20 mm graded stone aggregate) chullah hoods, stairways (except spiral staircases) including steps (square or spandrill) string pieces, carriages etc. any section straight or winding but excluding landings, RCC water tanks upto 1500 lit etc. complete all as specified and directed.

Supply only integral water proofing compound

M&L Brick work with fly ash bricks built in cement mortar (1:6) straight or curved on plan exceeding 6 mtr mean radius all as specified and directed.

M & L Brick work with fly ash bricks, half brick thick wall, straight or curved on plan to any radius built in cement mortar (1:4) complete, all as specified and directed.

M&L for Walling of random rubble masonry, coursed (Secunderabad type), well bonded, bedded and solidly hearted, built in cement mortar (1:6), complete all as specified and directed.

M&L for 25 mm thick Damp proof course in cement concrete 1:2:4 Type B-0 (Using 12.5mm crushed stone aggregate) mixed with WPC to horizontal or vertical surfaces including necessary formwork complete all as specified and directed by Engr-in-Charge. Note: WPC shall be measured and paid separately.

Use & waste formwork to sides of concrete foundations, rafts, footing, base of columns, raft and raft beams, sides & soffits of foundation (if any) of foundation and plinth beams and similar work, flat, rough finished surfaces, complete all as specified and directed.

Use and waste of form work to sides and soffits of floor or roof beams, lintles, cantlevers, shelves etc., flat rough finished surfaces, complete all as specified and directed.

Use & waste of form work to columns, posts, struts and stanchions etc., Square, rectangular or polygonal, flat rough finished surfaces, complete all as specified and directed.

Use & waste of form work to chullah hoods,chajjas, troughs and similor items including edges, complete all as specified and directed.

Use & waste of formwork to sides and soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surface, complete all as specified and directed.

Use & waste of formwork to edges of concrete flats, treads, breaks in floors,window cills, concrete railings ,openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exceeding 20cm wide rough finished surfaces, complete all as specified and directed.

Use & waste of formwork to staircases with slopping or stepped soffits including risers and stringers (excluding landing) etc. complete all as specified and directed.

S&F for solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling and fixing as per specification and drawing all as specified and directed.

S & F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing all as specified and directed.

S & F 35 mm thick IInd class hard wood factory made glazed and skelton shutters sizes of members as specified in SSR(Part-I) clause 8.20(a), open rebated and prepared to receive glass or gauge, edges of framing plain, chamfered or rounded, fitted with cut and miterd beads for securing glass or gauge etc. complete all as specified as directed by Engr-in- charge.

S&F 35 mm thick 2nd class hardwood, Plain, framed, panelled Factory made shutters (two panels), with lock rail and panel of 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS 1003 (Part-I) klin seasoned and chemically pressure treated complete all as specified and directed.

S & F for Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc., size of frame 125 x 60 mm complete all as specified and directed.

M&L for filleting in any position and to any shape in cement mortar 1:4 exc 25 Sqcm and n.exc 50 Sqcm all as specified and directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete.

S&F steel window with side hung shutter including projecting type hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and directed.

M&L sheet glass ordinary quality plain, 3mm thick, glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of apreture 1.4 mm & fixed with stainless steel wire staples fixed.

S&F for 100 mm long extruded Aluminium alloy butt hinges with galvanised mild steel hinge pin and fixed complete all as specified and directed.

S & F MS Butt hinges medium weight cold rolled of size 100mm complete all as directed.

S&F for 150mm long aluminium anodized barrel tower bolts of extruded section and fixed.

S&F for 150 mm long alluminium alloy anodized handles fabricated type

S & F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy

S&F 200mm, ordinary rat tail, rod pattern springs including roller and roller plate complete all as specified and directed.

S & F for Stairs (framed) including stringers, treades, landing,balusters, hand rails etc. including cleats, brackets, Fe 410-W (Gde-E-250) quality-B,etc complete all as spfd and directed.

S&F Mild steel TMT bars 6 to 8mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or securing with clips) complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over, cut to length bent to shap required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

S&F Mild steel TMT bars 5mm dia and over upto and including 10mm dia, cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed not less than 0.9 mm dia or securing with clips) in spacers, stirrups and binders complete all as specified and directed.

M&L Plain cement concrete (1:4:8) type D2 (40mm graded stone aggregate) 75mm thick as in sub base of flooring/hardstanding complete all as specified and directed.

M&L 100 mm thick PCC 1:2:4 type B2 using 40mm graded stone aggregate for footpath/ hardstanding finished even & smooth without using extra cement.

M & L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, with gery cement and no pigment laid over and including 50mm thick crushed stone sand coshioning etc completed all as specified.

M&L Polished shahabad stone slab 20-25 mm thick laid dry as in drain covers .exc 60 cm wide complete all as specified and as directed.

M&L for chequred cement concrete tiles 20 cm x 20 cm x 25 mm thick with grey cement and pigment, machine pressed : set, jointed and pointed in neat cement slurry, laid over including 15 mm thick screed bedding layer in cement mortar (1:6) all as specified and directed.

M & L 20-25mm thick Machine cut kota stone slab flooring laid over and including 20mm thick cement mortar screed in CM 1:6 and jointed with white cement slurry mixed with pigment to match the shade of the kota stone slab including rubbing and polishing etc complete all as specified.

M & L 20-25mm thick Machine cut Kota stone slab as in riser of steps, skirting, dado over and including 10mm thick backing coat in CM 1:4 and jointed with white cement slurry mixed with pigment to match the shade of kota stone slab including rubbing and polishing etc complete all as specified.

M&L Plain cement concrete (1:2:4) type B0 (12.50mm graded stone aggregate) filleting, complete all as specified and directed.

S&F for non skid coloured ceramic tiles 7 to 8mm thick (square or rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm, in floors laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:6), tiles jointed in neat cement slurry and pointed with white cement mixed with pigment to match the colour of tiles all as specified and directed.

S&F for glazed ceramic coloured tiles of size 300x200x7mm thick for vertical surfaces as in dado/skirtings set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles laid over and including backing coat in cement mortar (1:4), 10mm thick all as specified and directed.

M & L 75mm thick Plain Cement concrete (1:3:6) type C2 (using 40 mm graded stone aggregate) finished even aned smooth without using extra cement, complete all as specified and directed.

M&L for Rendering 15mm thick in cement mortar (1:4) mixed with water proofing compound on fair faces of brick work / concrete surfaces finished even and smooth without using extra cement, complete, all as specified and directed. Note: Supply only water proofing compound will measured and paid separately.

M&L Rendering 10mm thick on brick work or concrete surface as on walls in cement mortar (1:6) and finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 5 mm thick in ceilings with cement mortar (1:3) and finished even and smooth without using extra cement, complete all as specified and directed.

M & L for Preparation of new plastered wall surfaces and apply three coat of white wash, complete all as specified and directed.

M & L Preparation of new plastered ceiling surfaces and apply three coats of white wash, complete all as specified and directed.

M&L for preparation of new plastered wall surfaces and apply two coats of cement based paint over a coat of cement primer all as specified and directed.

M&L Preparation of new steel surfaces of area exceeding 10cm width & girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified and directed.

M&L Preparation of new wood surfaces of area exceeding 10cm width & girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

M&L for two coats of oil bound distemper on cement plaster over a coat of primer after preparation of surface on wall all as spd and directed.

M&L for salt glazed stone ware drain pipes, 150mm internal diameter of the pipe, grade 'A', laid in trenches and jointed as specified all as specified and directed.

M&L Plain cement concrete(1:4:8) type D2(40mm graded stone aggregate) as bed to drain pipes, 150mm bore dia, including packing under,and haunching against the sides of pipes after they are laid and tested; complete all as specified and directed.

M&L Plain cement concrete(1:4:8) type D2(40mm graded stone aggregate) as bed to drain pipes, 100mm bore dia, including packing under,and haunching against the sides of pipes after they are laid and tested; complete all as specified and directed.

M&L for SGSW 'grade 'A' drain pipe 100 mm internal dia laid in trenches , jointed, pointed in CM (1:1) and tested complete all as specified and directed.

M&L for SGSW 'grade 'A' drain pipe 150 mm internal dia laid in trenches , jointed, pointed in CM (1:1) and tested complete all as specified and directed.

M&L Reinforced concrete pipes 150 mm dia bore, class NP2, laid and jointed complete with collars laid in trenches and jointed as complete all as specified and directed.

M&L for Cement Concrete 1:3:6 type C-2 as concrete bed to drain pipes including forming cradles for pipes after they are laid and tested for 150 mm dia RCC pipes complete all as specified and directed.

M&L Reinforced concrete pipes 200 mm dia bore, class NP2, laid and jointed complete with collars laid in trenches and jointed as complete all as specified and directed.

M&L for Cement Concrete 1:3:6 type C-2 as concrete bed to drain pipes including forming cradles for pipes after they are laid and tested for 200 mm dia RCC pipes complete all as specified and directed.

S & F for vitreous china squatting pan (Orissa pattern) size 580 X 440mm white with integral foot rest, P or S trap set in and including concrete complete all as specified and directed.

S & F of PVC valveless, syphonic action type, flushing cistern, dual operated type, 10 ltr capacity, low level, white with inlet ball valve float and handle including brackets, with 32mm dia PVC pipe, complete all as specifeid and directed.

S&F for 15 mm dia PVC connections with PTMT nuts of length 600 mm, with check nuts complete all as specified and directed.

S&F of PTMT towel rail 600mm long fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190 gms) complete all as specified.

S & F for Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms), etc complete all as specifed and directed.

S & F for Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms), etc complete all as specifed and directed.

S & F for Grating round 140 mm size of PTMT complete all as specifed and directed.

Supply and fix Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified.

S&F for stop valve/ angle cock 15mm bore cast copper alloy but fancy type chromium plated with cup screwed down high pressure fixed to iron pipes or for unions complete all as specifed and directed.

S&F for fancy CP bib tap15 mm bore, cast copper alloy with screwed down, screwed for iron pipe or for brass ferrule.

S&F Rotational moulded polyethylene water storage tanks, of capacity 1000 litres (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, complete all as specified and as directed

S&F Rotational moulded polyethylene water storage tanks, of capacity 500 litres (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, complete all as specified and as directed

S&F 25 mm dia Ball valves high pressure of PTMT with epoxy coated aluminum rod and high density plastic ball screwed for iron pipe, 20mm bore (Min wt 210 gms) complete all as specified and as directed.

S&F ball brass valve high pressure with polythene float and fly nut complete screwed for iron pipe of size 20mm dia.etc complete all as spd and directed.

S&F vitreous china wash hand basin, flat back size 550x400mm including bracket, waste coupling etc complete.

S&F steel water tubing, ‘medium grade’ galvanised, 15mm bore including all fittings to walls and ceilings or laid in floors, complete all as specified and as directed.

S&F steel water tubing, ‘medium grade’ galvanised, 20mm bore including all fittings, fixed to walls and ceilings or laid in floors, complete all as specified and as directed.

S&F steel water tubing, ‘medium grade’ galvanised, 20mm bore including all fittings laid in trenches complete all as specified and as directed.

S&F steel water tubing, ‘medium grade’ galvanised, 25mm bore including all fittings laid in trenches complete all as specified and as directed.

M&L steel water tubing, ‘medium grade’ galvanised, 40mm bore including all fittings laid in trenches complete all as specified and as directed.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20mm bore complete all as specified and as directed.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 40mm bore complete all as specified and as directed.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 25mm bore, complete all as specified and as directed by Engineer-in-charge.

S & F for 110 mm dia PVC (SWR) junction single (Single T) equal or unequal with access Door.

S&F PVC (SWR) branch piece single (single Y) equal or unequal 110mm dia complete.

S & F for 110 mm PVC (SWR) bends any radius all as specified and directed.

S & F for 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors/ fixed to walls complete all as specifed and directed.

S & F for 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls including clips etc complete all as specifed and directed.

S & F PVC (SWR) vent cowl 110mm dia.

S & F PVC (SWR) vent cowl 75mm dia.

PVC (SWR) floor trap 75mm dia, plain with gratings including jointing with solvent cement

S & F for Vitreous china Urinal bowl flat back , size of 465x355x265mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete as directed

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110mm bore.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors for 110mm bore.

S&F PVC (SWR) bends any radius with access doors 110mm bore

S&F PVC (SWR) bends any radius 75mm bore

S&F Flushing pipe of polyethylene of low or high density, 900mm, 32mm dia, for low level cistern complete all as spd and directed.

S&F 40mm Dia Unplasticized PVC pipes of pressure rating 10 kgf/cm2 laid for urinal waste pipe complete all as specified and directed by Engr-in-Charge. (Length 900mm)

M&L 32 mm dia Waste pipe fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed waste pipe fixen with waste coupling complete all as spd and directed.

M&L 1:2:4 type Bo (using 12.5mm graded stone aggregate) as in surface channels including form work complete all as specified and directed.

M&L salt glazed stone ware gully traps square or rounded mouthed type & fix 150 x 150 mm fixed in cement concrete complete.

Cutting in to existing manholes for connecting new drains making good to pipe 100mm internal dia and rendering cutting out existing benching for and forming branch channels (1/2 round or 3/4 section)in cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate finished smooth and reforming benching complete all as specified and directed by Engr-in-Charge.

Cutting in to existing manholes for connecting new drains making good to pipe 150mm internal dia and rendering cutting out existing benching for and forming branch channels (1/2 round or 3/4 section)in cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate finished smooth and reforming benching complete all as specified and directed by Engr-in-Charge.

M & L for APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (weight not less than 150 gms/Sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 Ltrs/Sqm by forced application and applying one coat bitumen grade 85/25 @ 1.2 Kg/Sqm over finished with one coat of alluminium paint @ 100 ml/Sqm 10cm overlap fused uniformly by LPG torch flame including 10mm thick screed in CM 1:4 mixed with WPC finished even and smooth with out using extra cement on concrete surfaces, complete all as specified and directed by Engineer-In-Charge. (Make: IWL/STP/TIKKITAR)

Cutting/ boring on existing CI/GI pipe line 150mm dia (in position) for tapping of 25mm GI pipe for branch connection including necessary jointing material complete all as specified and directed.

Cutting/ boring on existing CI/GI pipe line 40/50 mm dia (in position) for tapping of 25mm GI Tpipe for branch connection including necessary jointing material complete all as specified and directed.

Cutting/ boring on existing CI/GI pipe line 50/80 mm dia (in position) for tapping of 40mm GI Tpipe for branch connection including necessary jointing material complete all as specified and directed.

Cutting of road or hard standing made of concrete or premix carpet, WBM, soiling and murrum filling including excavation for layiong of cable all as directed and making good the disturbed surface to match with the existing to the satisfaction of Engineer in Charge complete all as specified and directed.

M & L for Loose filling with broken bricks of gauge 80 to 150 mm in soakage pits/ soakage wells complete

Provision of Hume pipe septic tank for 10 users, including excavation & earthwork in any type of soil, PCC 1:4:8 type D2 as in foundation, vent pipe and connections complete all as shown on drawing No. TD/666 of Chief Engineer Chennai Zone.

M&L for construction of valve chamber 600x600x600mm with PCC 1:4:8 type D2 for foundation, brick wall in CM 1:4, PCC 1:2:4 type B1 for copingn rendering in CM 1:4 15mm thick for internal surfaces incl coping concrete, MS cover using 2mm thick MS plate with necessary angle frame hinges welded to it and applying 2 coats of synthetic enamle paint over a coat of red oxide primer including necessary locking arrangement complete all as specified and directed.

M&L Point wiring for one light point/fan point/bell point controlled by one switch with 1.5 sqmm multistrand copper conductor cable PVC (FRLS) insulated unsheathed copper conductor single core multi stand flexible cable and 1.50 sqmm PVC (FRLS) insulated unsheathed copper conductor single core cable ( green colour) as earth lead in and including PVC rigid conduit with all fittings for concealed type on stone / brick ,masonary walls, roof etc including in new MS sunk box of required size and all as directed by Engineer-in-Charge & 2 mm thick plastic laminated sheet for housing switches sockets, regulators etc, including running chases, pinning in and making good the disturbed surfaces to match with the existing specification ,complete all as specified and directed at site.

All as per item No. 137 hereinbefore but one exhaust fan point controlled by one, one way switch.

All as per item No. 137 hereinbefore but for One 3 pin 5 / 6 Amps switch socket outlet point on same board complete all as specified and directed.

All as per item No. 137 hereinbefore but for One 3 pin 5 / 6 Amps switch socket outlet point on independent board complete all as specified and directed.

All as per item No. 137 hereinbefore but for One 3 pin 15 / 16 Amps switch socket outlet point on independent board with 2.5 sqmm PVC (FRLS) insulated unsheathed copper conductor single core multi stand flexible cable and 2.5 sqmm PVC (FRLS) insulated unsheathed copper conductor single core cable (green colour) as earth lead complete all as specified and directed.

M&L switch piano flush type single pole one way 5 Amps complete all as specified and directed.

M&L lamp holder insulated body with back plate suitable for batten fittings complete all as specified and directed.

S&F Ceiling rose surface bakelite 65 x 50 mm 2/3 terminais complete all as specified and directed.

S&F LED tube light fittings 1 x 22 W, 230V, complete with all accessories internally prewired and including LED Tube rod connecting up with twisted flexible PVC copper conductor cable of 23/0.0076 from ceiling rose all as specified and directed. (Make : Cat No.Havelles Code No : REGAL BATTENT8UPT01X22WSSBSWH (Batten) CRYSTAL1213T8DSTL18WLED865SGLASS(Tube Rod) or equivelent in Philips / Crompton Greaves)

S&F Sheet metal enclosure MCB distribution board including 200 Amps bus-bar single pole and neutral 240V, 4 Ways, complete all as specifide and directed.

S&F Sheet metal enclosure MCB distribution board including 200 Amps bus-bar single pole and neutral 240V, 8 Ways, double door complete all as specifide and directed.

S&F LED lamp 10W, 240V all as specified and directed.

S&F LED lamp 7W, 240V all as specified and directed.

M&L Switch socket combination 5 Amps , multipurpose 2 in 1 flush type universal 3 pin / 5 pin with porelain base complete all as specified and directed.

M&L Switch socket combination 5 Amps , multipurpose 2 in 1 flush type universal 3 pin 5 & 15 Amps complete all as specified and directed.

S&F MCB single pole and neutral 6 to 32 Amps 240 Volts complete all as specified and directed.

S&F MCB single pole 240 Volts 6 to 32 Amps complete all as specified and directed.

S&F LED Building security lights New generation energy saving & enviromental friendly long life versitile pressure die cast aluminum roadway luminarie with high power LED 20 watts as light source and electronic driver bracket made into required shape for fittings complete with MS clamp, nuts and bolts and washsers as required at site of minimum 1.5 mtr long Med grade GI pipe 40 mm dia including painting with one coat of primer and two coat of aluminium paint complete all as specified and directed. Make :Havells cat part no: ENDURAPEARLSL20WLED757SASYTOPC are Eqivalent to PHILIPS / WIPRO / CROMPTON GRAVES / BAJAJ.

Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge o the plate not less1.5 mtrs below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts nuts, check nuts and washers of galvanized iron of steel all as shown in electrical plate No.3 connected to earthing test point incl necessary earth work, excavation PCC 1:3:6 type CI using 20mm graded stone aggregate for earth chamber provn of PCC cover 40 mm thick 1:2:4 mm type B1 funnel with water Pipe, GI pipe, 15mm dia medium grade protection pipe, GI earth lead complete all as specified and directed by the Engr-in-charge.

Supply, fixing and testing exhaust fan heavy duty type single pahse 230 volts 50 Hz of 300mm sweep SP Turbojet of 1400 RPM with metal body and blade with louvers, frame complete all as specified and directed

M&L House service bracket (hook type complete with 3.0m long G.I pipe 40mm dia Medium grade, two Nos 90 degree bend M.S hook and stay or guy including taking down of old unserviceable one all complete all as specified and directed

Supply and lay in trenches / fixed to pole/ walls etc and commissioning XLPE insulated and PVC sheathed heavy duty LT 1100 Volts grade armoured UG cable with aluminium conductor 2 core 10 Sqmm complete all as specified and directed.

M&L for brick protection cover using old size bricks, sub class B, laid dry and flat abutting each other with width equal to length of brick and gap between adjacent bricks not exceeding 10mm complete all as specified and directed.

S&F Ceiling fan of sweep 1200mm, 230 volts, 50 Hz, fixed to ceiling with down rod including fan regulatorand connecting up with twisted flexible PVC copper conductor cable of 23/0.0076 from ceiling rose to fan complete all as specified and directed.

M&L for 50mm GI pipe laying, fixing complete including all fittings light grade for protection of UG cable complete all as specified and directed.

S&F bulk head fitting 10W luminaires with all accessories including lamp holder etc., with one No 10 W LED bulb and connecting up with twin core twisted flexible PVC copper conductor cable of size 23/0.0076 from ceiling rose complete all as specified and directed.

S&F 1100 V grade heavy duty cable PVC insulated aluminium stranded conductor served with inner sheathing of PVC tape and over all PVC sheathed twin core cable flat or circular stranded conductor of size 10 Sqmm in service connections suspended by insulated hangers not more than 1 mtr apart incl 4 mm GI suspension wire complete with all as specified and directed.

BHATNAGAR ASSOCIATES

m/s s indra reddy constructions