Construction of underground water storage tank of 10,000 ltr capacity along with water lifting arrangement and installation of submersible tubewell and PVC water tanks etc. in Transport workshop at CCS HAU, Hisar (re-invited)

Amount

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved (HSR 5.70)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. (HSR 4.14)

1 :4: 8 ( 1 Cement : 4 coarse sand (zone-Ill) : 8 graded cum stone aggregate 40 mm nominal size) (HSR 6.1.6)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to plinth level: 1 : 1. 5: 3 ( 1 cement : 1. 5 coarse sand (zone-Ill): 3 graded stone aggregate 20 mm nominal size). (HSR 6.14.1)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor four level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3graded stone aggregate 20 mm nominal size) (HSR 6.15)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1: 1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 graded stone aggregate 20 mm nominal size). (HSR 6.16)

Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc.complete in all respect above plinth level. Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, over1aps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to beincluded in the rates for reinforcement. Thermo-Mechanically Treated bars of grade Fe-500D kg or more (HSR 6.34.6)

Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement: 4 coarse sand) {HSR 7.20.1}

Providing and laying of conglomerate floor 50mm thick cement concrete topping 1 :2:4 (HSR 10.7)

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete {HSR 13.27}

Labour for laying, jointing, fixing and testing G.1./P.V.C./W.I. pipelines and special tees, bends, sockets, elbow etc. inside building and testing etc. complete including cutting threading. Including cost ofspecials 25 mm internal diaMeter of pipeline (HSR 20.20.2.3)

Cutting holes up to 23 cm through stone masonry or brick work in cement walls for pipes and making good including repointing, replastering and finishing according to existing finish where required. 22.86 cm thick wall (HSR 20.26.2)

Cutting holes up to 23 cm square for pipes in floor and roofs of cement concrete reinforced concrete or reinforced brick work and making good including, repainting, replastering, replacing bitumen and colour or whitewashing where required. 115 mm thickness of roof or floor (HSR 20.28.2)

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 25 mm nominal bore (HSR 22.94.3)

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 25 mm nominal bore (HSR 22.98.1)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore (HSR 22.103.3)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank (HSR 22.181) {2000 litre +1000 litre= 3000 litre}

Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required. (HSR 24.1.1)

Providing and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in 15 mm dia G.I. pipe from earth electrode as required (HSR 24.1.11)

Supplying & jointing three core flat cables of Finolex, Polycab, Ecao & Bunton with bare bunched copper conductor insulated and sheathed with PVC for submersible pump motors with voltage grade 1100 volts marked with IS:694:1990 including cost of jointing materials as well as carriage, loading, unloading etc., complete in all respects to the satisfaction of Engineer-in-Charge. (NS) 2.5 square mm (copper)

Supply and erection of underground cable, loose in existing pipe or trences complete with necessary connection:- (NS) (iv) 10 sqmm 2 core cable Armoured Make:- Havells/Polycab/KEI

Providing and fixing cast iron elbow of 3" i/dia size ISI marked, complete in all respect. (NS)

Providing and fixing monoblock pumping set of 1.0 HP capacity single phase with 1" x 1" pump (inlet and outlet), complete in all respect of Taxmo/Crompton Greevs Make. (NS)

Supply of GI pipe 'B' Class ISI Marked Ravindra/Jindal/Parkash(Surya) Make. (NS) 25 mm i/d

Boring of well 6" dia size upto 100 feet deep (suitable for 5" dia PVC pipe) with suitable boring system, complete in all respect as per directions of the Engineer-in-Charge.(NS)

Supply, lowering, fixing & jointing PVC blind Pipe 5" internal dia size of 6kg/cm2 pressure (in the bore hole) of Prince/ Supreme/Skipper make complete in all respect. (NS)

Supply, lowering, fixing & jointing PVC slotted/perforated Pipe 5" internal dia size of 6kg/cm2 pressure (in the bore hole) of Prince/ Supreme/Skipper make with PVC filter jali and dhaga etc. duly wraped over PVC perforated pipe, complete in all respect. (NS)

Providing and fixing PVC end cap (for 5" i/dia PVC pipe) of Prince/ Supreme/Skipper make complete in all respect. (NS)

Providing and fixing copper revitts of best quality, complete in all respect. (NS)

Providing, fixing and jointing PVC column pipes 2½" i/dia size (in 3.05 ltr length with coupler/sockets or other system with acessories as required) jointing with pumping machinery and lowering into tubewell and testing etc., complete in all respect. (NS) Make:- Prince/Supreme/Skipper

Providing and fixing 3.0 HP capacity submersible pumping set single phase (V4) with 2½ i/dia delivery of KSB/LUBI/KOEL make, complete in all respect.(NS)

Providing and fixing electric Panel suitable for 3.0HP capacity submersible pumping set consisting of all required items/accessories like ampere Meter, volt Meter, starter, main switch & wires for connections etc. of L&T / Havells, Make, complete in all respects. {NS}

Development of tubewell bore for atleast 12 hours (or till develop of cavity) for 6"dia bore with suitable engine/system complete to the satisfication of the Engineer Incharge. complete in all respect. (NS)

Providing and fixing MS plate (Heavy duty) of suitable size on the top of bore of 5"i/ dia PVC pipe, complete in all respect. (NS)

Providing and fixing G.I. bend of 2½" i/dia size with flange of Unik/Unko make, complete in all respect. (NS)

Providing and fixing MS clamp (Heavy duty) of best quality complete in all respect. (a) For 2½" i/dia size pipe (NS)

Providing and fixing MS clamp (Heavy duty) of best quality complete in all respect (b) For 5" i/dia size pipe (NS)