REPAIR MAINT OF INTERNAL ELECTRIFICATION EXTERNAL ELECTRIFICATION DEEP FREEZERS EXHAUST FAN REFRIGERATORS ROS ACS GEYSERS CEILING FAN SOLAR WATER HEATER AND OTHER CONNECTED WORKS AT JAKLI RTC DHANSAL UNDER GE ARMY DHAR ROAD

Amount

Taking down old unserviceable/deteriorated batten/PVC conduit point wiring aluminium/ copper from existing place i.e. light, fan, socket or power points complete with all unserviceable fittings such as switches, sockets,bell push , ceiling rose, pendants, Holders, etc and making good all disturbed surface to wall, floor etc by means of cement mortar (1 : 3) or plaster of Paris and to match / finish new surface as the existing surface either by using same colour distemper, Putti or white / colour wash all as required and directed by Engineer-in-Charge.

M & L for concealed point wiring on wall and ceiling/roof with necessary fixing arrangements with PVC-FRLS insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade drawn in and including rigid non metallic white / ivory PVC conduit medium grade ISI marked not less than 20 mm dia with all conduit accessories/ fittings such as junction boxes, bends, tee, elbow etc including anodized MS sunken boxes made out of MS sheet of thickness not less than 1.6 mm with earth dolly and Bakelite laminated sheet 3mm thick ISI marked for fixing of switches / sockets, fan regulators, wall mounting fittings, door bell & bulkhead etc with MS screw and cup washers including PVC-FRLS insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade for continuous earthing including cutting the chases and making good the surface by cement mortar (1:3) and for matching / finishing of new surfaces either by means of plaster of peris/ Putti or distemper / colour wash with same existing colour surfaces all as specified and directed by Engineer-in-Charge for the following:-

One light /Fan/Bell point controlled by one switch 6/5 Amp one way single pole.

One 3 pin socket outlet 6/5 Amps controlled by one switch on the same board with other switches.

One 3 pin 6/5 Amp socket outlet controlled by one switch independent board.

All as per item No 2 here-in-before but for power point wiring with 2.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable and 1.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable as continuous earth lead.

S&F switch piano flush type (ISI marked), single pole, one way 6 Amp, 240 Volts complete all as specified and as directed.

S&F switch piano flush type (ISI marked), single pole, one way 16/15 Amps, 240 Volts including complete all as specified and as directed.

S&F socket outlet 3 pin, 6 Amp piano flush type including complete all as specified and as directed. Make-Anchor/Havell/Cona

S&F socket outlet, 2 in 1, 3/5 pin 6 / 16 Amp, piano flush type complete all as specified and as directed.Make-Anchor/Havell/Cona

S&F bell push 5/6 Amps SP flush type complete all as specified and as directed.Make-Anchor/Havell/Cona

S&F ceiling rose, surface bakelite, 65mm x 50mm, two to three terminals complete all as specified and as directed.Make-Anchor/Havell/Cona

S&F for batten angle lamp holder insulated body with back plate suitable for batten fittings including complete all as specified and as directed.

S&F Ding dong sound door call bell electric AC 240 volt, 50 Hz ding dong type including taking down unserviceable complete all as specified and as directed.

Supply & Fixing medium step type fan regulator , 240 Volt AC, socket size, medium step" ISI marked complete all as specified and directed.

Point wiring for one light/ fan/bell point controlled by one switch using 1.5 Sq mm FRLS copper conductor cables (multistanded) PVC insulated and unseathed in and including PVC concealed conduit as per site requirement (thickness not less than 1.5mm and 20mm dia), medium grade with Modular sunken boxes & PVC back plate for mounting modular type switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts coppper conductor cable 1.5 Sq mm as earth wire stranded and conected to earth dolly as specified.Note:- Cutting and making same the wall patchs after laying the wire and conduit using putty, white wash and distamper. The surface should be made smooth using putty and should match exactly with the existing wall finish. Make:Havells/polycab/Finolex

All as per srl item no 13 but One light /Fan/Bell point controlled by one switch 6/5 Amp one way single pole.

All as per srl item No 13 but for 3 pin 6 Amps socket outlet independent board including PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly.

All as per srl item No 13 but for 3 pin 6 Amps socket outlet on the same board including PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly.

All as per Srl item No 13 but for 3 Pin 16 Amps socket outlet independent board with cable 2.5 Sq mm including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire standard and connected to earth dolly.

S&F for modular switch 6 Amps single pole one way 230 V, 50 Hz, AC , with inner/outer plate complete all as specified and directed by Engr In charge..

S&F for modular switch 16 Amps single pole one way 230 V, 50 Hz, AC , with inner/outer plate complete all as specified and directed by Engr In charge. .

S & F modular Bell push flush type 6 amp 230 V, 50 Hz, AC , with outer/inner cover complete all as specified and directed by Engr In charge. .

S&F for modular socket 3 Pin 6 Amps flush type 230 V, 50 Hz, AC , with outer/inner cover complete all as specified and directed by Engr In charge. .

S&F for modular socket combined 2-in-1, 6 Pin 6 & 16 Amps 230 V, 50 Hz, AC , flush type with outer/inner cover complete all as specified and directed by Engr In charge. .

M &L Ceiling rose, surface bakelite 65x 50mm two to three terminals fixed on PVC Round Blockcomplete all as specified and directed by Engr In charge.

S & F calling Bell ding dong 230 volts single pole 50Hz complete all as specified and directed by Engr In charge

S & F for electronic step type fan regulator 120 watt 230 volts 50 C/S deluxe modular type complete all as spcified and directed..

M & L for sub main wiring in replacement of worn out aluminium conductor wire with two run of FR PVC insulated unsheathed flexible copper conductor (Multistrands), single core of size 4 Sqmm, 1100 Volts grade and one run of 2.5 Sqmm FR PVC insulated unsheathed as earth (In Green Colour), flexible copper conductor (Multistrands) for continuous earthing conforming to IS 694 with latest amendments and including drawing in PVC rigid conduit not less than 20 mm dia ISI marked medium grade incl fitting like bends, elbow, junstion box, reducer, junction boxes, tee bell mouth all fixing accessories such as coupler lock, nuts, saddles pipe hooks etc complete including Cutting & Chasing required on brick wall not exceeding 10 CM girth for concealed conduit wiring and making good to disturbed surface with cement mortar 1:3 and distemper / colour wash etc to match with existing surfaces including facing / finishing complete , connecting incoming / outgoing electric connections by using required size copper lugs / thimbles and making good the disturbed surface to match with existing complete in all respect all as specified and directed. Note :- 1. Two run of single core cable with one run of contineous earth wire of copper conductor wire Flexible (Multistrand) of FR PVC insulated and PVC conduit pipe with fitting shall be measured and paid as one unit length.

Supply & Fixing in replacement of old unserviceable DB by SPN Distribution Box, double door of protection grade IP 43 in fine powder coated, matt finish with best CRCA sheet, fitted with shrouded neutral, insulated pin type copper bus bar, Din rail, earth bar of 4 way, confirming to IS 13032 & 8623 complete all as specified and directed.

Supply & Fixing in replacement of old unserviceable DB by SPN Distribution Box, double door of protection grade IP 43 in fine powder coated, matt finish with best CRCA sheet, fitted with shrouded neutral, insulated pin type copper bus bar, Din rail, earth bar of 8 way, confirming to IS 13032 & 8623 complete all as specified and directed.

Supply & Fixing in replacement of old unserviceable DB by SPN Distribution Box, double door of protection grade IP 43 in fine powder coated, matt finish with best CRCA sheet, fitted with shrouded neutral, insulated pin type copper bus bar, Din rail, earth bar of 12 way, confirming to IS 13032 & 8623 complete all as specified and directed.Make-Legrand/Schenider/L&T/Indo Asian

Supply & fixing in replacement of AC/Geyser box by sheet steel enclosure in single pole and neutral fitted with two pin and earth plug and socket complete with one single pole MCB, 240 volt, 20 Amps , 'C' series of suitable rating complete all as specified and directed .

Supply & Fixing MCB SPN, 32 Amps 240 volts, AC , 10 KA breaking capacity 'C' Series,"ISI marked and conforming to IS 8828/IEC 60898-1 complete all as specified and directed.Make-Legrand/Schenider/L&T/Indo Asian

Supply & Fixing MCB SP, 05 to 32 Amps 240 volts, AC , 10 KA breaking capacity 'C' Series,"ISI marked and conforming to IS 8828/IEC 60898-1 complete all as specified and directed.Make-Legrand/Schenider/L&T/Indo Asian

Supply and fixing Mirror optic fitting by recess/surface mounted mirror optic LED luminaire fitting with paralite P5 louvers 35/36 watt LED, 6500K, white/warm white dimention 600mm x 600mm fitting for grid type ceiling including control driver and other accessories complete all as specified and directed.

S&F Wall mounted LED batten 18 Watt with 01 No LED tube rod, extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver including dismantling taking down unsv FTL fitting T8 type any type complete all as specified and directed. Make-Crompton/Phillips/Wipro

S&F LED building security light 15/35 watt, 230V complete with all accessories and including connecting up to ceiling rose with 0.5 sqmm three core copper flexible conductor cable, One GI medium grade suitable size dia bracket of total length 50 cm and fixed to wall with 1 Nos MS Clamp and fastener incl dismentling taking down unsv fitting any type all as specified and directed.

S&F Bulk head fitting 10 watt LED incl water proof , weather proof all as specified and directed in replacement of old unserviceable filling .complete all as directed by engr-in-charge.

Supply and fixing LED lamp 12 watt, CDL, B-22 cap, (Pin type), 230V, PF-0.95 (min) incl dismentling taking out unsv CFL/LED Bulb. complete all as directed by engr-in-charge.

S & F service connection with twin core 10 Sqmm 240 volt heavy duty un armured PVC insulated stranded aluminium conductor cable with GI supporting wire of suitable size in replacement of old unseriveable conductor cable complete.

Excavation in trenches not exceeding 1.5 meter wide and not exceeding 1.5 meter in deep getting out in hard/dense soil for stay assembly/laying of cable/errection of poles etc complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers n.exc 25cm thick.

Removing of excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point.

M&L PCC (1:2:4) type B-1 using 20mm graded aggregate as in coping of new pole /motor foundation/ reconstruction old damaged copings etc, including necessary form work complete all as specified and directed

M & L for dry Sand cushioning in trenches for protection of cable including watering and consolidation all as specified and directed.Note: Punned thickness shall be considerd for measurment purpose

M & L for well burnt brick sub class B old size laying in trenches perpendicular to axis of the cable complete all as specified and directed.

Supply and laying in trenches/Floor or fixed to Pole/Wall GI pipe light grade with fitting of size 50 mm bore for protection of cable including dismantling existing pipe complete all as specified and directed by the Engineer-in-Charge.

M&L for cutting of PCC/Hard standing/WBM road not exceeding 20 cm in width not exceeding 30 cm in depth for passing of LT cable and making good of disturbed surface to match with the existing surfaces by using old and new material i.e bitumen/PCC (1:3:6) type C-1 complete all as specified and directed .

Taking out existing worn out/old PVC insulated cable in 4/2/3.5 core of 185 sqmm to 70 Sqmm size of 1100 Volt grade in pieces from trenches making loop for transportation and removal from site after taking proper shut down from MES competent staff competentlete in all respect and as directed at site.

Taking out existing worn out/old PVC insulated cable in 4/2/3.5 core of 50sqmm to 10 Sqmm size of 1100 Volt grade in pieces from trenches making loop for transportation and removal from site after taking proper shut down from MES competent staff competentlete in all respect and as directed at site.

Material and labour for fixing or passing through pipe, laid in trenches or fixed to pole/wal or fixed to LT panel board, 1100 volts grade heavy duty cable with PVC insulated stranded aluminium conductor served with inner sheathing of PVC tape, armoured with galvanised steel wire or tape and overall PVC sheathed 35 Sqmm 3.5 core with required aluminium cable lugs all as specified and directed.

-- do-- as per item no. 45 above but size 185 sq mm 3.5 core

-- do-- as per item no. 45 above but size 150 sq mm 3.5 core

-- do-- as per item no. 45 above but size 70 sq mm 3.5 core

-- do-- as per item no. 45 above but size 95 sq mm 3.5 core

-- do-- as per item no. 45 above but size 25 sq mm 4 core

-- do-- as per item no. 45 above but size 16 sq mm 4 core

-- do-- as per item no. 45 above but size 10 sq mm 2 core

Taking out existing worn out/old PVC insulated cable in 3 core of 95 Sqmm to 120 sqmm size of 11000 Volt grade in pieces from trenches making loop for transportation and removal from site after taking proper shut down from MES competent staff complete in all respect and as directed at site.

Supply & laying HT XLPE Insulated screened aluminium stranded conductor cable PVC bedded galvanized strip armoured heavy duty 11 KV cross sectional area 95 Sqmm 3 Core (Earthed)conforming to IS 7098 lead in duct/trenches complete all as specified and directed.

S&F sheet metal enclosure box made out of 3.15 mm thick CRCA sheet with powder coated paint (CPRI approved) double door outdoor type including solid aluminium bus bar of capacity 100 Amp 4 Nos strip with locking arrangements, enclosure box to be fixed on plinth foundation 1:2:4 and 150 mm above ground level including MS angle/ channel consisting of necessary fixing arrangements for incoming & out going cables with cable glands, lugs, nut, bolts, washers and fixing arrangement , PCC work including necessary flat iron clamps with nuts, bolts & washers and Powder coated all as specified and directed..Including taking down old unsv

Supply And Fixing cable jointing kit for 11 KV (earthed) grade cable for outdoor termination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 50 Sqmm to 95 Sqmm..Including taking down old unsv

Supply And Fixing cable jointing kit for 11 KV (earthed) grade cable for straight through heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 50 Sqmm to 95 Sqmm.Including taking down old unsv

Dismantling and taking down old/unsv insulator of any type any size from pole/stay complete all as specified and directed.

S&F pin type, porcelain, vitreous, brown, including one galvanised mild steel spindle, two galvanised iron washer and one galvanised iron nut, 100mm height and 65 mm dia for 1100 volts grade all as specified and directed.

S&F shackle type,porcelian vitreous white, brown or green insulator including galvanised mild steel straps, washers, insulators bolts ,washer and nuts of size 100 mm height and 115 mm dia for 1100 Volts grade complete all as specified and directed.

S&F Loop type insulator, porcelian vitreous brown of size 65x90mm and clearence hole 16mm all as specified and directed.Including dismantling and taking down

S&F Disc type insulator porcelain, vitrous 145mm high and 255 mm dia ball and socket type white, brown or green single disc with tension clamp for conductor for working pressure voltage 11000 V .

M & L triple pole mechanically operated GOD mounted on insulators and steel frame with operating mechanism worked from ground level 11000 volts grade of current carrying capacity up to 200 Amps complete incl removing the existing U/S one.

S&F in Replacement of MCCB 250 Amps 4 Pole, 25 KA, 415 V, 50 Hz complete all as specified and directed.

S&F in Replacement of but MCCB 200 Amps 4 Pole, 25 KA, 415 V, 50 Hz complete all as specified and directed.

M&L for trimming of branches of trees touching LT/HT electric over head line and making clear about 3 mtr in radius by climbing up tree or by providing ladder, at a height 7 mtr and above and carrying and depositing where directed not exceeding 50 mtr.

Dismantling taking down unserviceable flood/street/post top lantern/gate light fitting any type any capacity from Pole/Building for replacement complete all as specified and directed.

S&F Supply and fixing post top lantern LED type 35/40 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete .

Servicing, repairing, overhauling and testing of Voltage Stabilizer of capacity upto 100 KVA by disconnecting the incoming and outgoing connection strip opening the stabilizer complete for taking out the unserviceable servo motors, auto control, circuit plates, dimmer and switches, voltmeter with switches and replace the following and testing on full load as directed by the Engineer-in-Charge for the following Capacity :-(a) Servo motor as per existing size - 01 No, (b) Voltmeter 0 to 500 Volts with switch. - 01 No, (c) Voltage on off adjusting switch (Auto control Switch), (d) Supply and pouring transformer oil after dehydrating the sump - 50 Ltrs, (e) Roller Wheels as per existing size - 01 Nos, (f) Voltmeter 0-300 Volts - 03 Nos (g) Supply and fixing of dimmer 63 KVA -01 Nos (h) Shifting of stablizer from Jhajjar Nallah to Approachable road and further to workshop will also consider in thi s job complete all as specified and directed by engr in Charge.

Supply,fixing, connecting, testing and commissioning LED street light fittings 70 Watt ,240 VOLT, current 0.31 Amps, 5700 Temp, new generation energy saving & environmental friendly long life versatile pressure die-cast aluminium IP66 road luminaire with high power LEDs as light source and electronic driver.Including taking down old unsv one.

Supply and fix in replacement security light fitting bracket made up of 25/32/50 mm dia medium grade pipe of length 0.9 mtr with bending in shape by hot or cold method with 2 nos 50x4 mm MS flate clamps with nut bolts and washer etc all as directed

Dismantling concrete poles/ struts, any size and credited to contractor

Supply and fixing in replacement of concrete pole to Steel tubular swaged poles type 410 SP-31 (9.0 meter long) complete with cast iron base plate, finial taper plug, bolts, nuts & screws etc including making the holes on the pole (bottom and top) suitable size for drawing of wire 1.5 sqmm 3 core round flexible for connection of security light fitting from junction box to light fittings including of one primer coat, one under coat and one finishing coat of silver paint all as specified and directed.

Supply,fixing, connecting, testing and commissioning LED flood light fittings 100/120 watt ,240 volt, 0.57 Amp current, > 0.95 PF, 5700 K Temp ,new generation energy saving & environmental friendly long life versatile pressure die-cast aluminium IP66 road luminaire with high power LEDs as light source and electronic driver. Including taking down old unsv one.

Material and Labour for Repair of LED Solar street light fitting 15 Watt , including solar panel, charge controller with dusk down sensor complete.Complete all as specified and directed by EIC.

Material and Labour for Replacement of LED Solar street light battery Lithium Ion of capacity upto 60Ah Complete all as specified and directed by EIC.

Servicing of transformer any type,any make 11000 Volts / 433 Volts step down/step up, indoor/out door type of capacity upto 200 KVA comprising following work services :- (a) Disconnection of cable termination of HV & LV ends.(b) Opening of top cover by removing nuts, bolts and all mounting accessories and conservator tanks for visual inspection.(c)Checking of HV/LV insulators including internal inspection (d) Replacement of corroded nuts/bolts with double washers, burnt lugs, etc by new one (e) Servicing of tap changing gears by cleaning and polishing tapping contact points. (f) Removing, cleaning, polishing of bushings and studs of both HV/LV side by using soft cotton cloth including checking for cracking and refixing the same.(g) Refixing all cable terminals HV & LV sides and transformer top cover, conservator tank and other fitments in position.(h) Cleaning and heating of silica gel in breather.(j) Connecting HV & LV side with existing incoming and outgoing cables including re-connection of earth strip/lead.(k) HV side cable connection shall be made with new HV tape & M Seal Monoplast as required at site.(l) All marshalling boxes to be cleaned from inside. (m) All the terminal connection of control and relay wiring to be checked and tighten.(n) Examine the rollers carefully includes greasing them properly.(o) Checking of earthing connection and tightening nuts& bolts with ensuring the earthing system working properly.

De-hydration/ filtration of transformer oil by hiring on line filtration plant to achieve di-electric strength not less than minimum 50 KV including following work services :- (a) Removal of all suspended particles such as dust, rust, scales, collided carbon oxidation sludge etc upto < 1 micron.(b) De-hydration of transformer oil under vaccum. (c) Circulation of heated oil and filling of treated oil in transformer tank. (d) Top up the transformer oil upto the level NOTE : (i) Contractor shall use the vehicle mounted filtration plant with new suitable size heavy duty hose pipe. (ii) The transformer oil required for replacing/top up shall be measured and paid separately as "Supply only" (iii) Conducting field testing of di-electric strength of the transformer oil before and after filteration (iv) Checking the megger/earth resistance values with battery operated megger of 5 KV

M&L for Filling / topping of new transformer oil having dielectric strength not less than 60 KV complete including centrifuging of oil (if required) up to getting dielectric strength not less than 60 KV all as specified and directed by the Engineer-in-Charge.

Supply and fixing breather assembly of Transformer with new silica gel upto 200 KVA transformer as per existing make and type complete all as specified and as directed.

Supply and fixing brass terminal stud with nuts, check nut, oil seal and washer for HV side of transformer of any make ( as per sample) up to 200 KVA transformer complete all as specified and as directed.

Supply and fixing brass terminal stud with nuts, check nut, oil seal and washer for LV side of transformer of any make (as per sample) up to 200 KVA transformer complete all as specified and as directed.

Supply and fixing bushing of HV side as per existing size/Model of the capacity up to 200 KVA transformercomplete all as specified and as directed.

Supply and fixing bushing of LV side as per existing size/Model of the capacity up to 200 KVA transformer complete all as specified and as directed.

M&L for painting of transformers/stablizers capacity up to 200 KVA including HV/LV side marshalling box with one coat of synthetic enamel paint by using spray painting method including cleaning of existing surface of all dirt and greasy materials alongwith marking of SM/MES Nos with sticker letters n. exc 2 cm height at appropriate places complete after isolating the transformer from the electric supply and to be earthed all as specified and as directed. Location- Jhajjar Nallah, Old Cook House, Power House.

M&L for rewinding with supper enameled double paper covered copper wire/ strip for HV/LV (11/0.433KV) winding having existing size and giving proper insulation and de-moisturizing before assembling the winding core and including primary testing, ratio testing, no load testing, core insulation testing including taking out unserviceable winding wire complete all as specified and as directed.Note : Rewinding and testing on load of transformer to be carried out through approved firm.

M&L for preparing scraping the old painted surfaces on two pole structure and applying two coat of aluminium paint on steel tubular swaged poles HT 11 mtrs long and bracket, channels, angles,GOD including making/pasting three nos cricular strips of 300 mm wide yello & black colour with synthetic reflected enamel paint and marking /stencil writing of pole numbers with black paint after taking proper shutdowm\n from Competent MES Authority complete and all as specified and directed.

Surface dressing not exceeding 15 cm deep and getting out in soil including cleaning away all grass vegetation saplings, bush under grouting, roots etc and removing rubbish to a distance of 50 M outside the periphery of area complete all as specified and as directed. Location:- Jhajjar Nallah Pump House area, Old Cook House Area, Power House Area,Filteration Plant Area.

M&L for preparing scraping the old painted surfaces on sign board and applying two coat of White paint on Sign Board 1.5 mtr wide and 1 mtr long along with angles of hieght 2 mtr including making Danger Sign on board by painting with RED synthetic enamel paint and complete and all as specified and directed.

Taking down for servicing of split / window type AC 1.5/2Ton Capacity including cleaning of cooling coil, air filters/plasma filters etc., (Indoor unit), condenser, compressors, fan motor etc., (Out door unit) with vacuum cleaner OR cleaning solution including checking the servicibility of electrical/electronic circuits relays, wiring kit, thermostat switches knobs, Remote control unit, fan, blower, etc., and keeping the AC unit in satisfactory working condition all as specified and as directed by Engineer-in-Charge.

Supply and Fixing following defective spare parts of Split AC unit of Cap 1.5/2 Ton against item No-85

(a) Running capacitor 36 MFD Make : Bentex/Delcon/Havells

(b) Running capacitor 45 MFD Make :- Unistar/Asian/Havells

(c ) Starting capacitor 100-120 MFD Make:- Bentex/Delcon/Havells.

(d) Starting capacitor 120-150 MFD Make :- Bentex/Delcon/Havells

(e) Starting Relay 1022/ 1622 Make :- Renutral/ Sri Ram/Micro Tech

(f) Starting Relay 2000 Make :- Renutral/Sri Ram/Micro Tech

(g) Thermostat switch 2059/2064/2054 Make :- Indfass.

(h) Main printed circuit board (PCB) with electric accessories and sensors suitable for split AC 1.5 Ton capacity

(i) Condenser fan blade for spilt Type A.C Cap 1.5 Ton made of Plastic.As pes sample

(j) Copper filter double capillary pencil type.as per sample

(k) Wiring kit for A.C Window/split Type 1.5 ton as per sample

(l) Remote control for split AC Cap 1.5 TR of any make as per site requirement

Taking down unserviceable copper pipe of size 1/4" and supply & fixing new copper pipe 1/4" complete including brazing, welding, but bolts and screws of reqd size complete all as directed by Engr-in-Charge

Description all as per item No 85.14 above but size 1/2"

Material & labour for detecting the leakages of gas of split type AC capacity 1.5 from any location and rectified/stopped the leakages by gas welding or by any other manner and make it function all as directed by Engr-in-Charge

Charging of Gas in Refrigerator, Water Cooler, Air Conditioner, Deep Freezer of any make of under mentioned Gas

Disconnecting from mains and Taking down for servicing of Water Cooler of Capacity up to 180 Ltrs including cleaning of cooling coil, condenser, compressors, fan motor etc with cleaning solution including checking the servicibility of electrical/electronic circuits relays, wiring kit, thermostat switches knobs, fan and blower, etc., and keeping the Water cooler unit in satisfactory working condition all as specified and as directed by Engineer-in-Charge.

Supply and fixing following defective spare parts of Water cooler unit of Cap up to 180 Ltrs against item No-88

(a) Over load protector device for up to 180 Ltr Cap. Water Cooler. Make : Sidwal / Usha / Blue star.

(b) Over load protect device for 180 Lts Cap. Water cooler. Make : Sidwal / Usha / Blue star.

(c) Starting relay open type/Box type suitable for up to 180 Ltr. Make : Sidwal / Usha / Blue star.

(d) Starting Capacitor 80-100 MFD Make : Unistar/Bentex

(e) Running Capacitor 25 MFD Make: Unistar/Bentax.

(f) Condenser fan blade plastic for Motor 1/32, 1/35 .

(g) Copper filter pencil type single / Double Capillary.

(h) Self closing/pushtaps for water cooler Cap up to 180 Ltr.

Supply and installing it by the company made new sealed unit compressor suitable for upto180/220 Ltr Water Cooler alongwith test Certificate from manufacturer including one year gurantee period, cleaning of condenser by machine doing vacum the fully system & testing as directed by Engr-in-charge. Make Tecumsha /Voltas/Sidhwal / Blue star / Godrej.

Disconnecting the electric mains and Taking out unserviceable condenser fan motor 1/10, 1/16 HP from water cooler cap up to180 Ltr and supply and replace with new motor single phase AC 220 V of same Cap including reconnecting the electric connections and testing . Make : AUE, Cromption Greaves / Cool Master as directed by E-in- Charge.

Disconnecitng the mains and Taking out the unserviceable condenser coil fins type and S&F new condenser coil fins type as per existing size & patterns for Water/Coolers Cap up to180 Ltrs.

Dismantling the evaporator/cooling coil of water cooler capacity up to180 Ltrs, checking the leakages of gas and rectify the leakages by gas welding or as other manner and refixing as directed by Engr-in-Charge.

Taking out the Water Cooler Tank from water cooler up to180 ltrs cap & repair the tank with brazing welding etc to stop the leakage of tank incl provn the inserting glass wool tarpaulin sheet etc and repair to cooling coil and refixing as per original position & testing and commissioning

Supply and Fixing of PVC connections 15 mm dia bore with PTMT nuts of length 900 mm including taking down the unserviceable PVC connections.

Disconnecting from mains and Taking down for servicing of Refrigerator/Deep freezer of Capacity 165 to 310 Ltrs including detecting the leakage of gas, cleaning of cooling coil, condenser, compressors, with vacuum cleaner or cleaning solution including checking the servicibility of electrical/electronic circuits relays, wiring kit, thermostat switches knobs, etc., and keeping the Refrigerator unit in satisfactory working condition all as specified and as directed by Engineer-in-Charge. Make of Refrigerator / deep freeze - LG / Godrej / Kelvinator.

Supply and fixing following defective spare parts of Refrigerator/Deep freezer 165 to 310 ltrs cap :-

(a) Thermostat switch with Knob Make :- Indfoss or Renutrol

(b) Starting relay 1/6 H.P. Open type with O.L.P. Make : KOI / Whirlpool / LG / Godrej.

(c) Starting relay 1/8 H.P. open type with O.L.P. Make : KOI / Whirlpool / LG / Godrej.

(d) Copper filter single capillary pencil type.

(e) Interior light fittings with bulb

(f) Refrigerator compartment Glasses

Supply, connecting and testing of compressor suitable for 165 to 180 ltr Refrigerator or Deep freezers equivalent capacity & testing the same with one year gurantee in working condition all as directed by Engineer-in-Charge. Make : Kirloskar/Whirlpool/Godrej

Dismantaling, Repairs / maint of RO water purifier system. Make : Renuka Model No RWT - ROS - 007 complete with replacement of the unserviceable parts on making the system serviceable as per manufactures recommendation. Note : new parts will be measured and paid separately under respective item Supply and fixing.

(a) Replacement of micro spun 20. Make Renuka code RWI 107.

(b) Replacement of CTO 20. Make Renuka Code RWI 109.

(c) Replacement of GAC - 20. Make Renuka Code RWI 110.

(d) Replacement of membrane housing 50. Make Renuka Code RWI - 125.

(e) Replacement of UV system 100. Make Renuka Code RWI 137.

(f) Replacement of flow restrictor adjuster. Make Renuka Code RWI 134.

(g) Replacement of micronic membrane 50. Make Renuka RWI 127.

Taking down carefully storage type electric water heater (geysers) of any capacity including labour for repair/renewal/replacement of defective parts with new parts. Desconnecting of electric and water supply connection and descaling of geysers vesswel and reassembling of geysers, and installing the same in position and making necessary mounting/electric/water supply connection and testing complete all as specified and directed by Engr-In-Charge. Note :- New parts shall be measured and paid separately.

(a) Supply and fixing heating element of capacity 2 KW geysers of any make ISI marked complete as approved by Engr-In-Charge. Make Racold/Ditz/Airex

(b) Supply and fixing heating element of capacity 1.5 KW geyser of any make ISI marked complete as approved by Engr-In-Charge. Make Racold/Ditz/Airex

(c) Supply and fixing inlet/ outlet pipe assembly with rubber gasket inbcluding nuits, bolts, washers for geysers of 50/35/25 ltrs capacity complete as approved by Engr-In-Charge.

(d) Supply and fixing inner tank vessel made out of copper sheet 22 gauge for geysers of capacity 50ltrs complete as approved by Engr-In-Charge.

(e) Description all as per here in before but inner tank vessel capacity 25 litre complete.

(f) Supply and fixing indicator lamp 240 volts suitable for geyser as per site requirement complete all as specified & directed.

(g) Supply and fixing outer tank vessel capacity 25 litre complete.

(h) Supply and fixing glass wool suitable for geyser of capacity 50/35/25 ltrs complete all as directed and approved by Engr-In-Charge.

(i) Supply and fixing geyser assembly suitable for 25 to 50 ltr capacity ISI marked as per existing make as approved by Engr-In-Charge

(j) Supply and fixing thermostate switch for geysers of capacity 50/25 Ltr ISI marked as per existing make as approved by Engr-In-Charge

(k) Supply and fixing NRV suitable for 15mm GI pipe ISI marked as per existing as approved by Engr-In-Charge

(l) Supply and fixing safety valve suitable for electric geyser complete of make as approved by Engr-In-Charge

(m) Supply and fixing flexi PVC connection 15 mm size with PTMT nuts of length 450 mm long for geyser

(n) Supply and fixing GI anchor bolts and Nuts with rowel plug for mounting the geyser.

M&L for tubes medium grade galvanised with all fitting and fixed of size 15 mm bore complete with walls and ceiling or laid in floors with iron spacers grouting in cement mortars, including taking out old unserviceable pipe and making good to disturbed surface with cement mortars and white washing to wall surface to matching existing surface complete all as specified and directed.

Disconnecting and taking Down the Desert cooler of any type and size carefully dismantling complete for servicing by cleaning the bearing/bush water pipe fan etc by cleaining solution and replacing the unservisiable items like motor,bearing ,fan blade condensor, flexible cable, canopy, etc., assembling Desert Cooler and refixing in the original place connection and testing complete all well as specified and as directed Note;- Replacement of unserviceable items are included in this job

Disconnecting and taking out the water dispenser of any type and size carefully dismantling complete for servicing by cleaning the bearing/bush water pipe fan etc by cleaining solution and replacing the unservisiable items like cold thermostate,hot thermostate,colding chio,Deep drawn Hot tank, energy efficient cold tank,condenser for water dispenser,etc and refixing in the original place connection and testing complete all well as specified and as directed Note;- Replacement of unserviceable items are included in this job

Disconnecting and taking down the ceiling fan of size 1200/1400 mm sweep carefully dismantling complete for servicing by cleaning the bearing/bush by cleaining solution and replacing the split pin and unserviceable items like bearing, bushes, rubber real, condenser, flexible cable, canopy, etc., assembling Ceiling fan and refixing in the original place connection and testing complete all well as specified and as directed Note;- Replacement of unserviceable items will be measured and paid underrespective items

(a) Supply and fixing of ball bearing for 1200/1400 mm sweep Make;- TATA / SKF/NBC

(b) Supply and fixing of gun metal bushes for 1200/1400 mm sweep ceiling fan as per sample

(c) Supply and fixing condenser 2.5 Mfd for ceiling fan

(d) Supply and fixing condenser 4 Mfd

(e) Supply and fixing rubber reel suitable for 1200/1400mmsweep ceiling fan with nuts, bolts and wahsers etc.,

(f) Supply and fixing PVC 3 core Cord Flexible copper insulated cable 24/0.2mm size Black/Grey colour Make:-Plazza/Kalinga

(g) Supply and fixing down rod 400mm long with holes for nuts & bolts suitable size dia for housing ceiling fan complete all as specified and directed.

(h) Supply and fixing hanging clamps suitable for ceiling fan with rubber, nuts and bolts complete all as specified and directed.

Collecting the burnt ceiling fans of any make from AGE E/M store yard/ site taking out to reputed work shop dismantling removing the burnt winding, rewinding of ceiling fan with super enameled copper conduct winding wire of same gauge, insulating, varnishing, baking, including wornout bearing/bush greasing assembling and transporting the same and fixing and testing of following size at site all as specified and as directed by Engr-in-charge,

(a) 1200/1400 mm Sweep

Collecting the burnt exhaust fans/wall fan of any make from AGE E/M store yard/ site taking out to reputed work shop dismantling removing the burnt winding, rewinding of Exhaust fan with super enameled copper conduct winding wire of same gauge, insulating, varnishing, baking, including wornout bearing/bush greasing assembling and transporting the same and fixing and testing of following size at site all as specified and as directed by Engr-in-charge,

(a) 300 to 450mm sweep

M&L for Earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 3.75 M deep below normal ground level) with top edge of the plate not less than 3.15 M below normal ground level, connected to galvanized earth strip 32mmx6mm by means of bolts, nuts, check nuts and washers of galvanised iron including necessary excavation and earth work ,PCC pit chamber in PCC (1:3:6) type C-1 using 20 mm graded aggregate with 50 mm thick pre-cast RCC cover in (1:2:4) type B-1 using 20 mm graded stone aggregate, reinforced with 8 mm dia bar@75mm c/c both way with two Nos lifting handles of 12 mm dia mild steel plain bar, funnel with wire mesh, lugs, 50mm dia galvanised iron protection pipe light grade ,watering pipe of size 20 mm dia galvanised iron light grade, main Earthing strip upto 7.5M including charcoal dust, common salt etc all as shown in electrical plate No. 3 of SSR Part-I 2009 including testing on completion complete all as specifed and as directed. Including Taking Down old Unsv Earthing.

Ditto, item no 109 but using galvanised earth lead wire 4mm dia.

S&F Switch socket combination outlet 3 pin, 5 Amp piano flush type including taking down complete all as specified and as directed.

S&F Switch socket combination outlet, 2 in 1, 3/5 pin 6 / 16 Amp, piano flush type including taking down complete all as specified and as directed.

Supply and install 10 W bollard decorative luminaire IP 65 rated inverted Pyramid type LED bollard with soft 360 deg light distribution including fixing arrangement installaed in PCC foundation and taking down old unserviceavle all as specified and directed Make Crompton / Philips / Bajaj / Osram

Supply and fixing in replacement of Automatic Light Timer switch with Nature switch Cat No. SWADEEP-02EC12KW3P, infra ray sensor with pre sawn switching off timer, 4-8 hrs, of Maximum load capacity of 4KW per phase. Degree of protection conforms to IP 65 complete all as specified and directed.

95 Sqmm to 120 Sqmm

35 Sqmm to 70 Sqmm

6 Sqmm to 25 Sqmm

M&L for removing old paint from chain link fencing , steel section post by paint removers, cleaning by scrapping and preparing the surface and applying two coats Painting complete with synthetic enameled paint of existing colour over a coat of red oxide primer complete all as directed by Engr-in-Charge.

M&L for painting and write LT Panel number of LT Panel with one coat of Existing Panel Colour with synthetic enamelled paint all as specified and directed. LT Panel of any Size

M&L for painting and write pole number of steel tubular pole with one coat of alumium paint incl cross arm, bracings, supports, nuts, bolts, of street light poles from above copping to top of pole and marking with alternate white and yellow/black paint strip 30 cm wide (5 Nos) with synthetic enamelled paint all as specified and directed. LT Pole of 9 mtr

Supply and fixing of Junction box made out of thermo plastic material of size 240x130x110 mm with provision of single phase cable connector incomming and out going with MCB SP 6-32 amps for security light fitting/PTL IP 65 protection totally enclosed weather proof with cable entry along with GI clamps nut bolts & washer fixed on pole including dismantling/taking out old unserviceale one all as directed.

Supply and fix water proof electric distribution box( 3 Phase, 4 Wire), wheather proof IP-65 protection suitable for outdoor use, pole mounted, factory made of suitable size comprising one No. MCB SP 6 Amps, 240 volts SPN bus bar not less than 25mm x 5mm aluminium strip and fixing clamps of suitable size two nos including necessary nuts, bolts and locking arrangement with lock, pressure type, four Nos connection holes in each bus bar with nuts, bolts and washers made of galvanized iron and connection thimble etc. complete all as specified and directed.

Labour only for taking down and lifting up high mast light fitting including replacing the unserviceable items to make the fitting serviceable ,serving, greasing of steel reopened adjust/repair the timer, supply and fixing in replacement the contacts lifting mechanism with all accessories as required, complete all as directed by the Engineer-in-Charge. (Note :- Spares like chokes, ignitor lamp & LED fitting will be measured and paid separately)

S&F of Glow Sign board of following size and showing given name on Acrylic sheet/Fibre glass re-inforced translucent corrugated sheet 2mm thick with MES Logo (symbol) necessary Vinyl Blue Sticker along with 02 No's LED Tube light fitting 20 watts incl nessary connection with 1.5 Sqmm flexible copper wire and fixed on structure with aluminum equal angle as per required size , sufficient Nos brass machine screws with and incl errection complete all as directed.Note:-GI pipe 50 mm bore for errection of glow sign board will be paid separately. GLOW SIGN BOARD SIZE 2.50 m x 0.60m x 0.20m-01 No incl angle iron size 50 x 50 x 6mm length 01 ft –02 Nos grouted in Main entrance Piller with cement plastering or GI Pipe 50mm bore for fixing the glow sign board. MES POWER HOUSE DANSAL UNDER GE(ARMY) DHAR ROAD

Cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint complete all as specified and directed.

Deduct Schedule of Credit of Rs. (-) 69046.50 (Minus) as listed in Schedule 'A' Part-II. Contract Sum shall be arrived after deducting the credit amount Note: Tenderers will not quote against this item being a firm amount.

K S BUILDERS (BID ID -3498085)

M/SHansrajbuilder (BID ID -3491659)

M/S PRAJAPATI ENGINEERS (BID ID -3492100)