Supply of Spares of coal mills (HP-1103) to RGTPP, Khedar, Hisar on annual rate contract basis.

Supply of Spares of coal mills (HP-1103) to RGTPP Khedar Hisar on annual rate contract basis

Bearing Housing For RC Feeder and Coal Mill GT1651907

Eccentric Bearing Housing For RC Feeder and Coal Mill

Air Restriction Ring Large Size (Length Approx. 1800mm, Width 60mm, Thickness 28mm) (1 Set= 8 Nos.)

Air Restriction Ring Small Size (Length Approx. 1800mm, Width 35mm, Thickness 28mm) (1 Set= 8 Nos.)

Shroud Plate1360x120x10 (1 Set= 8 Nos.)

Roller Retainer Ring For coal mills MOC: 16Mn

Scrapper With Liner Plate long, MOC:IS 1030, Gr-II, (Cast Steel) MOC of linear ISS 276 ASTM grade-3

Scrapper With Liner Plate, Short, MOC:IS 1030, Gr-II, (Cast Steel)MOC of linear ISS 276 ASTM grade-3

Journal Housing Liner Upper, MOC: Cast Steel as per IS 1030 Grade-2

Journal Housing Liner Lower, MOC- SS-304

Wearable Adjustable Shrink (adjustable Orifice) for Coal Mill HP-1103, Coal PipeOD-710mm, Model-SMK Type-B (Wearable adjustable shrinks to be supplied with 2 no. extra flange for connection/installation with PC Pipe)

Feeder Outlet gate without actuator

Mill Body Deflector Support Plate MS, 1 Set= 3 Nos.

Bearing Housing Left For RC Feeder Model: CS2036GT1630407

Bearing Housing Right For RC Feeder Model: CS2036GT1630607

Screw Stem for Belt Tightening, MOC- SS-316

Idler Roller for RC Feeder Model:CS2036, 1 Set=12 Nos.

Bushing For RC Feeder and Coal MillGT1651807

Bearing Housing Assembly & Rode Housing Assembly For RC Feeder and Coal MillGT1632107

Seals of hot shut off gate- L2000 mm, Width 115mm, Thickness-1.5mm, MOC-SS-304

Seals of hot shut off gate-L1800mm, Width 115mm, Thickness-1.5mm, MOC-SS-304

Center Feed Pipe with Cone For Coal Mill

Dresser Coupling For center feed pipe of Coal Mill

Roller Liner Device for Coal Mill

Ventury vane for coal mill, hardness= 60-62 HRC , hard thickness=15mm

Flow measure device For PA Hot Air duct of Coal Mills

Journal Housing Seal Cover for Journal Assembly of Coal Mills MOC:IS1020 Cast Steel/EN24

Seal Wear of Coal Mill Journal Assembly Shaft OD: 470mm, ID: 390mm, Width: 102mm, (MOC- Carbon Steel EN-24 Hardness- 55-60 HRC)

Tie bolt with nut and Bush of Coal Mill

Lower Skirt for Coal Mill HP-1103 (MOC: Carbon Steel) 1 Set= 4 Nos.

Take Up Pulley For RC Feeder Model: CS2024, CS2036GT1650307

Coal Mill Side Liner (Bottom), MOC: MS Size:1mtrX 1mtr, Thickness:10mm (1 Set=03 Nos.)

Coupling for Cleanout Conveyor for RC Feeder

Locking Plate of Grinding Rolls L=274mm, T=32mm

Journal Assembly Top Cover Plate For Coal Mill

Journal Bearing Keeper MOC: En24 Forged, OD-456mm, ID-105mm, PCD-232 mm, 8 nos. of holes of Size M32, thickness-40mm

Tension Roller For RC Feeder and Coal MillGT1653407

Weighing Roller For RC Feeder and Coal MillGT1631107

Mill Discharge valve (MDV) size-28" without power cylinder for Coal Mills HP-1103

Metallic Expansion Bellow For PF Piping, Specification: 2 nos. Congulations, (SS 304, Thickness of congulation-2mm, thickness of inner sleeve-5 mm), Medium: Coal+ Hot Air. Maximum Air Flow per Mill:125 Tonne per Hour. Pipe OD-710mm, Thickness of Connection end-16mm (Mild Steel). Position of fitment: Vertical.

Expansion bellow for Pulverized Fuel Piping Specification: 04 Congulations (SS 304, Thickness of congulation-2mm, thickness of inner sleeve-5 mm). Medium: Coal+ Hot Air. Maximum Air Flow per Mill:125 Tonne per Hour. Pipe OD-710mm, Thickness of Connection end-16mm (Mild Steel). Position of fitment: Horizontal.

MS Plate for hot shut off Gate L-2000 mm, Thickness- 3 mm

MS Plate for hot shut off Gate L-1800 mm, Thickness- 3 mm

Wear Resistant Weld overlay plate with carbide layer of 6 mm for coal mills, Carbide layer of inner side of curved portion Dimension: Height-1500 mm, Width- 1000 mm, Thickness- 10 mm (1 Set= 06 No.)

MS Flange for Hot air Diaphragm MOC- Mild Steel , Thickness- 10 mm, ID- 805 mm, OD- 944 mm, PCD- 890 mm, No. of Holes- 20 Nos. of size- M18

Ventury Outlet for coal mill HP-1103 , MOC- Carbon Steel

Ventury Outlet Collar for coal mill HP-1103 , MOC- Carbon Steel

RAJU ENGINEERING WORKS PRIVATE LIMITED

UNITECH ENGINEERS

Shiv Shakti Engineering Works

ALFA ENGINEERING