SPG/N-10/6/26-27

Rough dressed timber planks fitted and fixed with nut bolts excluding frame work complete : In ground floor (i) 25mm thick planks (b) Sal Local

Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (B) Wall; With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m b) Area of each tile above 0.09 Sq.m (i) Coloured decorative

Supplyingand laying true to lineand level Double Charge Vitrified Tiles of approved brand conforming to IS15622: 2006( GroupBIa) and tested as per IS 13630:2006 (relevant parts) [Non-modular sizes for tiles with Water Absorption (av.) ≤0.08%]infloor , kirtingetc.usingpolymerisedadhesiveof 6 mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course and joints groutedwith admixture of ............... specific permission of Superintending Engineera)lnGroundFIoor:(sizenotIessthan600mmX600mmX9.5 mm thick) A) FLOOR

Supplying,fitting & fixing of 2-Track / 3-Track Aluminium sliding Window of all Aluminiumsections viz.window frame (top,bottom&side frame), shutter (top, bottom, side & interlock member) made of aluminium alloy extrusions conforming to IS733-1983&IS1285-1975,an............................ 10-12 Micron thickness Annodizing film Natural white 2 - TRACK SLIDING WINDOW

Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units:

Glazed aluminium sliding windows made of extruded and annodized alloy aluminium sectios, fabrications, ……………... excluding the cost of extruded aluminiumsections, glass, neoprene / EPDM gasket, locking arrangement and rollers. i ) 2 track sliding window.

Supplying, fitting & fixing of Aluminium fixed partion wall of all aluminium sections viz top, bottom and side member, intermediate member, glazing clip made of Aluminium Alloy Extrusions conforming to IS: 733-1983 and IS: 1285-1975, annodized conforming to IS:1868 ................................... a)for unsupported length of vertical member upto1.50 m. height of both ends of vertical member restrained but panel with in 0.90 sqm

Supplying ,Aluminium Grill with Fchannel frame of approved make and ........... ........................ Grill made with10 mm wide and 5.2 mm thick aluminium sheet having expansion width of 66.00 mm and weight not less than 3.26 Kg/Sq.m.

Providing and fixing exterior quality Aluminium Composite Panel (ACP) wall cladding on existing Al. /MS frame work with GI brackets, ACP fixed on the existing frame work by folding the edges of ACP panel (Engraving the rear surface of ACP sheet) with CP angles, cleats and strainless Steel screws forming groves at the periphery of ACP panel. Such grooves filled with foam and silicon sealant etc. complete with all materials (but including the cost of silicon sealant), labour, scaffolding and all other incidental charges complete in all respect as per specification and direction of Engineer-in-charge. (Mode of payment is on finished surface area of ACP) (b) 4mm thick (0.50mm Al.+3.0mm LDPE +0.50mm Al. PVDF coating)