SPECIAL REPAIR TO BUILDING NO 116 UNDER GE (SOUTH) MAMUN AT MAMUN MIL STN

Amount

Taking down chowkhats or frames of any description not exc 1.50 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware , complete all as specified and directed.

Taking down chowkhats or frames of any description exc. 1.50 Sqm and n.exc 4.00 Sqm each with shutters, (without taking off shutters from the frame) including builders hardware complete all as specified and directed.

Taking down Shutters of any description exc 1 sqm but not exc 2 sqm each including builders hardware complete all as specified and directed.

M&L for 18 to 20mm thick prelaminated PVC solid board (one side decorative choice laminate and other side balancing white) as in kitchen cabinet, cupboard and pelmet box fixed with screws to PVC/timber frame work complete all as specified and directed.

M & L for Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) as per specification & drawing complete all as specified and directed.

M&L for 35mm thick, 2nd class hard wood plain framed, panelled (factory made) shutters (two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12mm veneered particle board with commercial veneering on both faceS ,The size of rail and stile as per IS-1003 (Part-I) (Larger size to be provided) kiln seasoned and chemically pressure treated, fitted to chowkhats incl 02 coats of synthetic enamel paint over a coat of pink primer after preparation of surfaces complete all as specified and directed.

S&F for 35mm thick wire guazed and skeleton shutters (1st class softwood), open rebated and prepared to receive wire cloth, gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing wire cloth, etc, sizes of members of shutters as specified in fitted to chowkats all as specified and directed.

S&F for Factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail: Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing all as specified and directed. Note:- The colour of Style, Rail and Panel shall be as specified and directed by Engr-in-Charge.

M&L for Box type Steel windows and ventilators comprised of tubular frame and shutters made out of 1.25mm thick M S sheet tube factory made with double side hung wire gauged shutter & glass/glazed shutter (wire cloth and glass panes only shall be measured and paid separately) with steel handle and steel peg stay dovetailed or welded incl 2 Nos. tower bolts 150mm long for each leaf and 10mm square bar grills at spacing as shown on drg, welded to F I frame work, including other fittings; hinges, handles, tarred hold fasts fixed in PCC blocks all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed.

M&L for 3 mm thick sheet glass ordinary quality and glazing with oil putty or fixed with beads/ glazing pins not .exc 0.5sqm in each pane complete all as specified and directed.

M&L for 3 mm thick Figured glass (frosted on one side), pin head type and glazing with oil putty in squares not .exc 0.5sqm in each pane complete all as specified and directed.

M&L for Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks or galvanized wire staple complete all as specified and directed.

M&L for Aluminium anodised barrel tower bolt, extruded section 150 mm long , complete all as specified and directed.

M&L for Aluminium anodised barrel tower bolt, extruded section 100 mm long , complete all as specified and directed.

M&L for Aluminium anodised handle, extruded section of size 150 mm complete all as specified and directed.

S&F in repair Mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified and directed.

M&L for 300 mm aluminium alloy sliding door bolt with hasp & staple (bolt type) and fixing clip of sheets cast or extruded section and fixing sliding bolt of extruded section complete all as specified and directed.

M&L for 40 mm thick floor in PCC 1:2:4 type B-1 finished even & smooth without using extra cement ,including dismantling existing floor of any type and pattern and removal of rubbish out off the premises complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C-1 using 20mm graded crushed stone aggregate as in plinth protection laid in slope finished even and fair including making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio (1:2) by weight including dismantling existing floor of any type and pattern and removal of rubbish out off the premises complete all as specified and directed.

M&L for 12mm thick Endura brand (Johnson) or equivalent model in Kajaria/ Somany as approved by GE , exterior floor tiles (Square or rectangular) area of each tile exc 0.08 Sqm but not exc. 0.18 Sqm in floors , set & jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:4) (surface finished even and rough to receive Endura tile) including dismantling existing tiles of any type and pattern including cement mortar backing coat and removal of rubbish out off the premises, complete all as specified and directed.

M&L for 20mm thick Granite work (Telephone Black/ Lakha Red) (table rubbed and premirror polished) in single piece in steps, jambs, pillars, window-cills, cooking platforms ant the like set & jointed in neat cement slurry including pointing in epoxy grout to match with shade of granite, including making hole for gas pipe including rounding the edges of granite, laid over and including 15mm thick screed bed in CM 1:4 including roughening surfaces of existing concrete floor by picking, sweeping clean & washing down with water to remove dust and apply neat cement slurry @ 3.00kg of cement per sqm complete all as specified and directed.

M&L for Marble Green/Bhaislana Zebra 18 to 20mm thick (table rubbed and pre-mirror polished) in single piece in steps, jambs, pillars, window-cills, cooking platforms and like set and jointed in neat cement slurry including pointing in epoxy grout to match marble shade, including making hole for gas pipe including rounding the edges of marble stone , laid over and including 20mm thick screed bed in CM 1:6 including dismantling of existing tiles/stone etc complete all as specified and directed.

M&L for Cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregates) such as in column for fixing of truss, benching, coping, Bed blocks and the like, rounded or chamfered on edges including necessary formwork including demolition of existing concrete of any description and removal of debris out off the premises complete all as specified and directed.

M&L for Non-skid ceramic coloured rectified edges joint free tiles 8mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floors etc, set & jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:4) including demolition of damaged cement concrete of any type or description and removal of debris out off the premises etc complete all as specified and directed.

M&L for Non-skid ceramic coloured rectified edges joint free tiles 8mm thick as in skirting area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floors etc, set & jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 10mm thick screed bed or bedding layer of cement mortar (1:4) including taking out cement plaster sweeping clean & washing down with water to remove dust complete all as specified and directed.

M&L for coloured combination (Red & yellow/brown & ivory) machine pressed precast concrete rubber moulded chatura tiles having glossy finish of 55 mm thickness M-30 Grade grey cement and pigment complete all as specified and directed incl demolition of existing tiles. Make : KB industries/Mohindra industries

M&L for 10mm thick industrial homogeneous coloured tiles area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm as in floors etc, set & jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:4) including dismantling of existing tiles including cement concrete of any type or description and removal of debris out off the premises etc complete all as specified and directed.

M&L for Non-skid ceramic coloured rectified edges joint free tiles 8mm thick area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm as in skirting etc, set & jointed in neat cement slurry and pointed in coloured epoxy grout to match laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:4) including dismantling existing tiles of any type and pattern including cement mortar backing coat and removal of rubbish out off the premises complete all as specified and directed.

M&L for Glazed ceramic (coloured) tiles 7mm thick, of size 450mmx300mm on vertical surfaces such as dado etc, set and jointed in neat cement slurry and pointed in coloured epoxy grout to match tiles over and including 10mm thick backing coat in cement mortar (1:4), surface finished even and rough to receive tiles, including dismantling existing tiles of any type and pattern including cement mortar backing coat and removal of rubbish out off the premises complete all as specified and directed.

S&F in repair 15mm bore Stop valves fancy type, chromium plated cast copper alloy long shank and exposed part kit with fitting sleeve, operarting lever & adjustable wall flange (concealed type) screwed both ends for iron pipe or for unions complete all as specified and directed. Make : Jaquar Cat part No CON-083FT & CON-083FTK or equivalent of Hindware/Marc.

S&F in repair for single towel rail brass chromium plated 600mm long fixed with chromium plated screw and PVC cleat complete all as specified and directed. Make : Cat part No AQN-7711 of Jaquar or equivalent model in Hindware/Marc.

S&F in repair Brass Chromium Plated shower rose with arms fancy type with swivel joints 75 mm face dia of appoved make and cat part for 15mm bore iron pipes complete all as specified and directed. Make : Prayag Cat part No BS-73 or equivalent model in Hindware/Marc.

S&F 15 mm bore Stop valves/Angle valve cast copper alloy, chromium plated (ISI marked) , screwed down,high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repair complete all as specified and directed.

S&F in repair for 15mm bore bib taps fancy type with wall flange, chromium plated cast copper alloy long body with capstan heads, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F in repair for Rotational moulded polyethylene water storage tanks three layer of capacity 1000 litre, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm ball valve high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball and dismantling of existing PVC tank of any capacity, complete all as specified & directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed. Make:Paryag/Polytech

M&L for GI water tubing surface/concealed, 15mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) and application of bituminous paint on concealed portion of tubing, fixed to wall or ceiling or laid in floor, including taking down existing unserviceable GI tubing and connections complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

M&L for GI water tubing surface/concealed, 20mm bore, medium grade galvanized with all fittings (such as tee, elbow, socket, union, short pieces) and application of bituminous paint on concealed portion of tubing, fixed to wall or ceiling or laid in floor, including taking down existing unserviceable GI tubing and connections complete all as specified and directed. (Note : Cutting chases and making good shall be measured and paid separately)

Cutting existing steel tubing of 15 or 20 mm bore for alterations or additions (Each cut measured) in position without taking down complete all as specified and directed.

S&F in repair for 20mm bore Mild steel powder coated, single curtain rod (wall thickness not less than 1mm) including fancy type PVC brackets of approved design/pattern, funnels etc suitable for single curtain rod complete all as specified and approved by GE.

M&L for Brick work with Fly Ash Brick (Non-Modular) straight or curved on plan to any radius in half brick thick walls, built in CM (1:4), including dismantling of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc and removal of rubbish out off the premises, etc complete all as specified and directed.

M&L for Brick work with Fly Ash Brick (Non-Modular) straight or curved on plan to any radius in half brick thick walls, built in CM (1:4), including dismantling of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc and removal of rubbish out off the premises, etc complete all as specified and directed.

M&L for rendering 5mm thick cement plaster on surfaces of concrete ceiling in cement mortar 1:3, surface finished even and smooth using extra cement including taking down cement or cement lime plaster of any description and removal of rubbish out off the premises, complete all as specified & directed.

M&L for Rendering 15mm thick in two layers [base layer 10mm in CM 1:6 & finishing layer 5mm thick in cement mortar (1:4)] using liquid water proofing compound in IInd layer on brick work or concrete surfaces of wall, surfaces finished even and smooth using extra cement including taking down cement or cement lime plaster of any description and raking out joints, hacking for key, scrubbing down with water and removal of rubbish, out off the premises, etc complete all as specified & directed. (Note : WPC shall be measured and paid separately)

M&L for rendering 10mm thick on brick work or concrete surface in CM (1:6) on wall surfaces finished even and smooth using extra cement incl. in patches incl. taking down cement or cement lime plaster of any description and raking out joints, hacking for key, scrubbing down with water and removal of rubbish, out off the premises complete all as specified & directed.

M&L for rendering 10mm thick on brick work or concrete surface in CM (1:3) on in fasia /edges/ ceiling of chajjas/ roof projections etc surfaces finished even and smooth using extra cement including taking down cement or cement lime plaster of any description and raking out joints, hacking for key, scrubbing down with water and removal of rubbish, out off the premises complete all as specified & directed.

S&F in repair for Vitreous china white wash down water closet pan (pedestal pattern) with normal closing seat cover S-trap (Make : Jaquar Cat part No CNS-WHT-553SN or equivalent Cat Part/Model of Hindware/Parryware/ Somany) & hand shower (Health foucet) 8mm dia 1.5m long flex tube in chrome finish and wall hook with NRV (Back flow preventer) and connection to drain (or out going pipe) (Make : Jaquar Cat Part No ALD-577 or equivalent Cat Part/Model of Hindware/Parryware) and to flush pipe, antisyphonic pipe etc complete all as specified and directed

S&F in repair PVC flushing cistern dual flush type 10 Ltr capacity, valve-less syphonic action type, low level, complete with inlet, ball valve, handle, including brackets/pins, PVC flush pipe 32mm bore and PVC connection 15mm bore 450mm long complete all as specified and directed.

M&L for Vitreous china wash hand basin, white, flat back, size 550x400mm (Make : Jaquar Cat part No CNS-WHT-801 or equivalent model in Hindware/Parryware/Somany) including 15mm bore fancy type , chromium plated single hole wash basin mixer (Make : Jaquar Cat part No QQT7167B or equivalent model in Hindware/Marc.) brackets, CP waste coupling, 32mm bore PVC waste pipe of min 600mm long & 15 mm bore PVC connections, including cutting for and pinning in end of brackets or erecting stand fixed in repairs complete all as specified and directed.

S&F in repair for Vitreous China urinals, half stall urinal type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; flush pipe, waste coupling , and Union for discharge pipe. complete all as specified and directed.

M&L for Filling of sunken floor with PCC 1:5:10 type E2 using 40mm graded crushed stone aggregate including breaking and removal of existing filling of lime concrete/PCC/brick bats and rubbish out off the premises, etc complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for RCC( 1:1.5:3) type A-1 using 20mm graded crushed stone aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including necessary formwork including demolition of existing cover slabs of any description and removal of rubbish out off the premises etc complete all as specified and directed.

S&F in repair for 100 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with ears, fixed to wall with stack clamp made out of 50mm x 5mm galvanised flat iron fixed with bolt and nuts etc complete all as specified and directed.

S&F in repair for 75 mm bore, sand cast, cast iron soil, waste and vent pipe with cement joints, in any length with ears, fixed to wall with stack clamp made out of 50mm x 5mm galvanised flat iron fixed with bolt and nuts etc complete all as specified and directed.

S&F in repair for 100 mm bore, cast iron bends (any radius), diminishing pieces or tapers (large bore measured) with oval access door complete all as specified and directed.

S&F in repair for 75 mm bore, cast iron bends (any radius), diminishing pieces or tapers (large bore measured) with oval access door complete all as specified and directed.

S&F in repair for 75 mm Cast iron floor trap, with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F in repair for 75 mm Cast iron nahani trap, with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F in repair 100 mm Cast iron cowl, fixed with cement joints complete all as specified and directed.

S&F in repair stainless steel grating doom 100 mm dia fixed in floor complete all as specified and directed.

S&F in repair stainless steel grating doom 100 mm dia with waste hole fixed in floor complete all as specified and directed.

Supply only Polymer liquid water proofing compound of make Pidilite/Bauchemic/Fosrock, all as specified and directed.

M&L for 0.56 mm thick Plain Aluminium sheeting Alloy 31000 H4 fixed on crumple joint with overlap not less than 15 cm fixed in repairs complete all as specified and directed

Removing existing roof treatment (any type) roughening surfaces of old concrete by picking, sweeping/Brushing clean and washing down with water to remove dust and apply neat cement slurry with 3.Kg of cement per sqm.

M & L for APP modified roof treatment over existing non-accessible RCC roof slab / chajjah / canopy / parapet wall to be executed through approved applicator of the membrane manufacturer with following specification complete all as directed :- (a) Cleaning existing surface properly. (b) Applying oil bound bitumen primer @ 0.30 liter/Sqm manufactured by the same agency as that of APP with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface. (c) Laying not less than 3mm thick APP modified water proofing membrane weighing not less than 3.60 Kg/Sqm reinforced with non woven polyster fiber weight not less than 160gsm/Sqm using butane torch by torch application with 10cm side laps and 15cm end lap. Laying of membrane, Physical property of membrane shall be as under :- (i) Membrane weight not less than 3.60 Kg/Sqm. (ii) Non woven polyester weight not less than 160 gsm/Sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650/Sqcm and transverse not less than 450/sqcm at 230 degree Celsius. (v) Tear strength - longitudinal not less than 300 N & transverse not less than 250N. (vi) Elongation of reinforcement not less than 30%. (vii) Impermeability under water pressure not less than 3 Kg/Sqcm. (d) APP membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap. (e) Top of membrane shall be provide with solar reflective bituminous aluminum paint @ 0.1 Kg/Sqm as prescribed by manufacture of membrane.

M&L for preparation of newly plastered surfaces of wall & applying two coats of distemper oil emulsion (OBD) over a coat of primer as per manufacturer instructions (from same manufacturer of OBD) over a layer of wall care putty 3mm thick complete all as specified and directed.

M&L for preparation of old treated plastered surfaces of wall & applying one coat of distemper oil emulsion (OBD) complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint over a coat of alkali resistance primer as per manufacturer instructions complete all as specified and directed.

Preparing old treated wall surface and applying one coats of cement base paint complete all as specified and directed.

Preparing old treated wall surface including making surface clean, dry and free from any loose paint film, dirt, chalk, grease, fungus and algae and applying one coats of acrylic , antifungal emulsion exterior weather proof paint over a coat of alkali resistance primer as per manufacturer instructions complete all as specified and directed.

M&L preparation of old treated steel surfaces of any description over 10 cm in width or girth & applying one coats of synthetic enamel paint complete all as specified and directed.

M&L preparation of old treated wooden surfaces of any description over 10 cm in width or girth & applying one coats of synthetic enamel paint complete all as specified and directed.

M&L for one coats black bitumenous paint on surfaces of any description wood, steel, iron, concrete, brick, stone etc exceeding 10cm in width or girth all as specified and directed

M&L for preparation of new plastered surfaces of ceiling / chajjas etc and apply three coats of white wash on plastered surfaces complete all as specified and directed.

M&L for preparation of existing white washed surfaces of walls and apply one coats of white wash on plastered surfaces complete all as specified and directed.

M&L for preparation of existing white washed surfaces of ceiling and apply one coats of white wash on plastered surfaces complete all as specified and directed.

Taking down carefully unserviciable/ damaged copper/aluminium surface (batten/coduit or casing caping) point wiring any length for light/fan/socket or power including unscrewing from board (fitting and fixture such as switches, sockets, ceiling rose, lamp holders, brackets, pendent, regulators, sockets, Bracket /sketch fitting etc ) and removing material from site and making good to the disturbed surface to match with existing finish complete all as specified and directed.

M&L for Modular Point wiring using FRLS PVC insulated unsheathed /multi stranded copper conductor cable 1.5 sqmm including 1.5 Sqmm FRLS PVC insulated unsheathed copper conductor earth wire drawn through and including concealed PVC conduit of appropriate size not less than 20 mm dia and 1.8 mm thick including all fittings viz tees, bends, junctions box and approved make sunken modular metal flush gang box and suitable support frame and cover plate (inner/outer) of required modules for mounting modular switches/ sockets etc, connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing including connection of cable with MCBs or bus bar shall be done through proper size copper/brass thimble of pin/u type etc (conduit shall be fixed on surface of ceiling with necessary saddles where concealing of conduit is not feasible), for light/fan/bell point complete all as specified and directed. (Note : Modular switch/bell push/fan regulator etc shall be measured and paid separately under respective items.)

All as per Srl item No. 81 above but two point controlled by two Nos switch 06 Amp one way, complete all as specified and directed.

All as per Srl item No. 81 above but for 5 pin 5 Amp socket outlet point on independent gang box and suitable support frame and cover plate (inner/outer) controlled by one switch 5Amp one way, etc complete all as specified and directed.

All as per Srl item No. 81 above but for 5 Pin 5 Amp socket outlet point on same board controlled by one switch 5 Amps one way on same gang box support frame and cover plate etc complete all as specified and directed.

All as per Srl item No. 81 above but for one 15Amp socket outlet point concealed using 2.5Sqmm FRLS PVC insulated multi-strand copper conductor wire including 2.5Sqmm FRLS PVC insulated unsheathed copper conductor earth wire and making good to disturbed surfaces of wall floor to match existing finishes complete all as specified and directed.

S&F Modular Socket outlet, 5 pin, multi purpose 2 module 6 Amps, AC 230 volts, etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVKSWW065 /Legrand Cat Part No 673452/ schneider Cat Part No P2005.

S&F Modular Socket outlet, 6 pin, multi purpose, 2 module 16 Amp, AC 230 volts, etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVKCWW163 Legrand Cat Part No 673455 / schneider Cat Part No P2106.

S&F Modular Switch 2 way 6/10 Amps , 1 module etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVSXXW101 or equivalent of Legrand/Siemens/schneider.

S&F Modular Switch 1 way 16 Amps , 1 module etc complete , all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVSXXW161 /Legrand Cat Part No 673411/ schneider Cat Part No P1101.

S&F Modular Switch 1 way 6/10 Amps , 1 module etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVSXXW101, Legrand Cat Part No 673401, Anchor Roma Cat Par No 289101, schneider Cat Part No P1001.

S&F Ceiling rose polycarbonate isolated body surface Bakelite, not less than 65 x 50 mm, three terminals, AC 230 volts etc, complete all as specified and directed. Make : Havells Cat Part No Reo/Cona Cat Part No 9246/GM Cat Part No 8224

S & F Fan regulator modular step type suitable for 1200/1400mm sweep ceiling fan hum free, 120W- 2 module including necessary connections complete all as specified and directed. Make : Legrand Cat Part No 673028/Crabtree Cat Part No ACARFHW005/Anchor Roma Cat Part No 66502.

Taking down ceiling fan of any sweep & size and refix in same position after overhauling including minor repairs by replacement of capacitor, safety pin, cap, nuts & bolts etc and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose to fan, including testing to ensure efficient functioning including application of one coat of synthetic enamel paint by spray painting & rewriting number complete all as specified and directed.

S&F Surface mounted 1x20 watt LED tube light fittings (4 feet long), prewired, decorative luminaire with inbuilt LED tube rod and acrylic end covers with all accessories and PVC Round/Square block for fixing of fittings and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc complete all as specified and directed.

S&F Surface mounted 1x10 watt LED tube light fittings (2 feet long), prewired, decorative luminaire with inbuilt LED tube rod and acrylic end covers with all accessories and PVC Round/Square block for fixing of fittings and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc complete all as specified and directed.

S &F the Bulk head light fitting LED type 10 watt complete with 10 watt LED and having IP-63 protection and fixing on wall/ceiling complete with all accessories and including connecting up with ceiling rose with & including PVC insulated and overall sheathed flexible copper conductor cable and including 3 core 0.50 Sqmm complete all as specified and directed.

S&F decorative wall mounting bed side light 2 watt fitting LED type having flexible complete all as specified and directed.

S &F building LED security light luminaries 25 W LED 5000K AC 230 volts, new generation saving & enviromental friendly long life versatile pressure die cast aluminium luminaries with high power LED as light source complete making connection with street light/ building security light box or OH line using PVC insulated and sheathed single core multi stranded copper conductor cable of size 1.5Sqmm including suitable size 32mm of bracket and light grade pipe for muntaining of fitting complete all as specified and directed.

S&F Lamp holder insulated body with back plate suitable for batten fitting including 12W LED lamp of approved make and cat part and PVC Round/Square block etc complete all as specifeid and directed.(Notes : Notes for Srl item No 94 to 99:- 1. Driver shall be potted antivibration type. 2. LM-79 and LM-80 test report with 1 Lakh burning hours LED life from NABL lab shall be povided. 3. CRI (Colou Rendring Index) of fixture shall be > 70. 4. CCT (Colout Correlated Temprature of fixture shall be 5700K ± 300 K. 5. System Lumen Efficacy shall be > 100Lm/W 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. 5 years gurantee shall be provided by contractor suppoted by OEM covering all parts of luminaire. 8. Lenses shall be Modular Type. 9. PCB used shall be MC PCB type 10. The defect liability period of LED light shall be 05 years from the certified date of completion & the Contractor shall replace / repair the defective fitting within 07 Days after handing over to Contractor for replacement / repair 11. CA No shall be written on each fitting before installation.

S&F for MCCB triple pole & neutral (TPN) 415 volts, 100 Amps, 10KA complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F Double door MCB DB VTPN, 415 Volts, 04 Way made out of CRCA powder coated sheets, IP43 protection with copper bus bar, including taking out old unserviciable DB any size/type complete all as specified and directed. Make: Legrand /L&T/Hager/SCHNEIDER

S&F Double door MCB DB SPN, 240 Volts, 12 Way made out of CRCA powder coated sheets, IP43 protection with copper bus bar including taking out old unsv DB any size/type, complete all as specified and directed. Make: Legrand Cat Part No 6077-11 or equivalent model in L&T/Hager/SCHNEIDER

S&F Single pole & neutral enclosure with a two pin & earth plug & socket complete with & incl. one single pole MCB 20 Amps 240 volts (C-series) complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F for MCB single pole (SP) 240 volts, 6 to 32 Amps, 10KA (C-series) , complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F for MCB single pole neutral (SPN) 240 volts, 6 to 32 Amps, 10KA ((C-series) complete all as specified and directed. Make : Legrand/Schneider/Hager

M&L for Sub main wiring with FRLS PVC insulated unsheathed 2X6 sqmm multistranded copper conductor cable 1100 V with 1X6 sqmm FRLS PVC insulated green multistranded copper cable for continuous earth drawn through & including concealed PVC conduit of appropriate size not less than 20 mm dia & 1.8mm wall thickness with all accessories including cutting grooves and making good disturbed surface to match existing including taking down existing surface sub main wiring complete all as specified and directed. (Note: Two runs of FRLS PVC cable with one run of earth conductor and conduit shall be measured as one RM.) Make for wiring : Polycab/Anchor/Finolex

M&L for earthing complete with galvanised steel earth plate electrode, 600mm x 600mm x 6mm thick, buried directly in the ground (earth pit not less than 2.25m deep below normal (ground level) with top edge of the plate not less than 1.50m below ground level connected to galvanized iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point, HDPE pipe 15mm bore as protection pipe, GI watering pipe 20mm bore light grade with funnel and wire mesh, charcoal and salt, 40mm thick pre-cast RCC (1:2:4) type B-0 (Nominal mix) cover reinforced with XPM (weighing n.less than 4 Kg/Sqm) with suitable steel handle, and angle iron 40X40X3mm frame and chamber of PCC (1:3:6) type C-0 (including earth work in any type of soil, removal of surplus soil to a distance n.exc.50m) and connecting, testing on completion, all as shown on electric plate No. 03 of SSR-2009 Part-I, complete all as directed. Notes: 1. Earth lead & protection pipes length upto & including 7.50 metre is deemed included in unit rate quoted by the contractor. 2. Earth filling shall be done by vegitable soil. 3. Soil shall be free from stone, boulders, aggregate, gravels .

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation etc (for cable, pole stay manhole etc), in any type of soil and getting out, complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc. 25cm thick, etc complete all as specified and directed.

Removing excavation material n exc. 50m & deposited where directed at a level n exc. 1.5m above the starting point etc complete all as specified and directed.

Supply , laying, testing and commissioning for 1100 volt grade XLPE insulated heavy duty cable, 25 sqmm 4 core, strip armoured with aluminium stranded conductor overall PVC sheathed laid in trenches including taking down existing cable & bricks complete all as specified and directed. Note : Excavation & Earthwork shall be measured and paid separately.

M & L for sand filling in trenches dry and and clean sand unwashed including punning around cable for protection of under ground cable complete all as specified and directed. [Note : Punned thickness shall be measured and paid]

M & L for well burnt bricks , laid flat ( old size) sub class B designation 75 for cable protection complete all as specifed and directed.

S&F for GI tubing 40 mm bore light grade laid in trenches/floors/ fixed to wall/poles for protection of cable with necessary fittings and FI clamps duly painted complete all as specified and directed.

Abrol construction co

dadwal engineers

Raghbir chand

RD BUILDERS

GANDOTRA CONSTRUCTION CO

Alishan Builders

KULBHUSHAN AGGARWAL

v k engineers and builders